SEARCH · Search NASA

Results for “CdTe:I”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Mitigation of J–V distortion in CdTe solar cells by Ga-doping of MgZnO emitter

Distortions in the current–voltage curves of CdTe-based thin-film solar cells with MgZnO emitter layers are not uncommon. Even when such distortions are very subtle with standard sunlight, they can be greatly accentuated by the removal of short-wavelength photons with optical filters, and the dark-curve turn-on voltage can be noticeably increased. The strong suggestion is that good J–V curves with full-spectrum light often rely on photogeneration of electrons from trap states in the MgZnO emitter. When the carrier concentration of the CdTe absorber is increased with external doping, there is a corresponding need for a larger MgZnO carrier concentration. Based on the assumption that the emitter carrier concentration needs to be comparable to that of the absorber, Ga-doping of the MgZnO was shown to very nearly eliminate the large filtered-light distortions and is arguably superior to MgZnO that relies on photogeneration. In addition, it was shown that photogeneration and recovery in MgZnO is relatively slow, so that without Ga-doping, the cell efficiency improves gradually for most of an hour in the light, and the turn-on voltage of the dark curve increases on a similar time scale when the light is removed.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Correlative nm-Scale Nonuniformity of Active Charge Carriers and Electrical Potential Along Both the Plane-View and Depth Directions in Group-V-Doped CdTe Thin Films: Preprint

We report nanometer-scale imaging on inhomogeneous distributions of active carrier and electrical potential in an As-doped CdTe film along both plane-view and film-depth directions. Despite Se grading, the SCM imaging does not show a clear variation of carrier concentration along the depth of the film. Instead, we observe carrier concentration variations of about 1 order of magnitude (high 1015 to low 1017/cm3) with inhomogeneous spatial regions ranging from a few hundred nm to a few ?m. This nonuniformity is distributed randomly in both the film lateral and vertical directions, independent of grain structure and GBs. We further mapped the surface potential using Kelvin probe force microscopy (KPFM). Higher potential was found on GBs, illustrating positive GB charging but not GB-specific carrier concentration. The results indicate that this suite of techniques can help identify nonuniform carrier concentration and potential fluctuations that can contribute to Voc deficits in GrV-doped CdTe devices.

CdTe thin film photovoltaics↗

DOE OSTI2026

Collaborative R&D with REEL Solar Inc (REEL) to Understand and Overcome Performance Limitations in CdTe Solar Cells: Cooperative Research and Development (Final Report)

This CRADA will focus on processing, advanced characterization, and testing of photovoltaic materials and devices to understand and improve REEL CdTe solar technology. This will include examining process variations and different buffer, absorber, and contact layers from REEL and NLR to maximize performance. The unique and diverse advanced characterization tools at NLR, such as time-resolved photoluminescence, capacitance-voltage measurements, electron beam scattered diffraction, cathodoluminescence, electron microscopy, TOF-SIMS, and other measurements will be applied to characterize REEL processing to improve understanding and guide experimental directions. Accelerated stability and potential induced degradation tests will be used to analyze metastability, short-and-long term degradation, and improve bankability. A second and major thrust this period will be joint development of Si/CdTe tandem solar cells to overcome industry wide terrestrial solar efficiency limits with the two lowest cost and manufacturable solar materials today. This will include developing novel transparent back contacts that can be incorporated into tandem structures and other novel solar applications, detailed analysis of designs and configurations for CdTe/Si tandem modules, and prototyping REEL CdTe Technology with Si bottom cells in tandem structures.

14 SOLAR ENERGY↗

DOE OSTI2024

Human Health Risk Assessment for Improper Landfill Disposal of End-of-Life CdTe Modules

The present work is a continuation of the 2020 IEA PVPS Task 12 Human Health Risk Assessment Methods for PV Part 3: Module Disposal Risks. The 2020 report performed a human health risk assessment (HHRA) for disposal of a cadmium telluride (CdTe) PV module in an unlined landfill, focusing solely on risks from cadmium. This study extends the 2020 HHRA on CdTe PV, analyzing eleven constituent elements: Cd, Se, Te, Cu, Si, Cr(III), Mo, Sn, Zn, Ni, and Al. The present HHRA was performed through two methods: utilization of the U.S. Environmental Protection Agency's (USEPA) Delisting Risk Assessment Software (DRAS V.4.0) on eight exposure pathways for cancer risk and non-cancer hazards; and comparison of exposure point concentrations to federal standards for groundwater, surface water, air, and soil exposure pathways. Cancer risks and non-cancer hazards posed by elemental leaching through all evaluated exposure pathways, using both methods, were found to be several orders of magnitude below USEPA health-protective thresholds. Cadmium exhibited both the highest risks and lowest uncertainty considering data availability on chemical content, leachate, and federal screening levels.

CdTe↗

DOE OSTI2020

Environmentally improved CdTe photovoltaic recycling through novel technologies and facility location strategies

Abstract Photovoltaic waste is projected to reach up to 78 million tons across globally dispersed locations through 2050. Current recycling infrastructure is inadequate to process these waste volumes responsibly. This necessitates commercializing novel, environmentally advantageous photovoltaic recycling technologies that improve upon incumbent industrial operations. CdTe photovoltaic recycling is a promising candidate for improvements as 25,000 tons of spent modules are recycled worldwide annually. This paper evaluates the operational performance and compares six novel technologies, the incumbent technology used in industry and one technology which extends the incumbent process across ten environmental impact categories. The tradeoff between incurring a transportation burden (ship or road) to recycle in a large‐scale centralized facility with a higher operational efficiency and avoiding transportation by recycling in a small‐scale decentralized facility with a lower operational efficiency is evaluated. Thermal delamination to eliminate the ethylene vinyl acetate and separate the photovoltaic glass panels is preferable to the incumbent mechanical process across nine environmental impact categories and decreases the climate‐change impact of CdTe photovoltaic recycling by 23%. Bath and probe sonication are ineffective for delamination, and the use of organic solvents is more environmentally burdensome than the incumbent mechanical process. Centralized recycling with shipping is environmentally preferable than with road‐based transportation. For every 100‐km increase in road transportation from the decentralized to the centralized facility, the inventory requirement in the centralized facility should be 6% lower than the decentralized facility for centralized recycling to have a lower climate‐change impact than decentralized recycling. The corresponding value for shipping is 0.4%.

Ravikumar, Dwarakanath↗

DOE OSTI2023

Photoluminescence of CdTe and CdZnTe compounds doped with 2% selenium

The addition of 2 % of selenium in CdTe and CdZnTe (CZT) exhibited an additional acceptor-bound exciton in photoluminescence (PL). From the PL and inductively coupled plasma mass spectrometer (ICP/MS) analyses, the additional acceptor-bound exciton emission is associated with a Cu impurity in the relatively low-purity (5N) precursor CdSe starting material. Additionally, thermal quenching of the acceptor/donor bound exciton emissions do not require a shift to any higher excited states or to the free exciton state. ICP/MS analysis also showed a higher concentration of Sn in CdZnTeSe (CZTS) compared to CdTe and CZT which is known to form a deep level trap at around E C – 0.83 eV. The trapping and de-trapping times indicate that the Sn-related deep trap acts as an electron trapping center. The relatively low electron mobility-lifetime product of CZTS might be correlated with the concentration of Sn in the impure CdSe material. Pulse height spectra using an Eu-152 gamma-ray source was taken for a 2-mm-thick planar CZTS detector. The spectra clearly showed all the expected gamma peaks with energy lower than 344.3 keV.

47 OTHER INSTRUMENTATION↗

DOE OSTI2023

Use of non-contact voltmeter to quantify potential induced degradation in CdTe modules

Potential induced degradation (PID) is a significant reliability issue for photovoltaic modules in the field. Conventionally, to detect the PID-affected modules, all the modules in a string are individually disconnected and measured using I-V (current–voltage) tracers. It is extremely time-consuming, expensive and unsafe (if the module connectors are field aged) approach. In our approach, we aim detecting the PID-affected modules quickly, inexpensively and safely without disconnecting individual modules in the string. In this study, contactless electrostatic voltmeter’s (ESV) strength was explored to detect the PID-affected cadmium telluride (CdTe) modules in a string. These contactless measurements on high-voltage PV strings could make this technique unique and preferable to detect PID-affected modules in a string compared to the I-V curve method. In this work, a CdTe module was stressed for PID using the Aluminum (Al) foil method in a walk-in environmental chamber, which resulted in a reduction of module's peak current (I max ), peak voltage (Vmax), and fill factor (FF), and hence power (Pmax). Outdoor light I-V, EL, and ESV measurements were performed pre- and post-PID to determine the effectiveness of the non-contact ESV technique. Further, the ESV technique successfully detected the change in V max , and hence Pmax, compared to the pre-and post-PID conditions. A difference of less than 2% was observed in the results of the non-contact and non-interruptive method compared to the conventionally used interruptive voltmeter or I-V tracer method. This technique and the test results demonstrate a significant promise to identify poor-performing modules in PV string without disconnection of individual modules in the string.

14 SOLAR ENERGY↗

DOE OSTI2025

Defect Stability in CdTe Based on Formation Energies and Migration Barriers

Native point defects are thought to play a key role in CdTe, either as compensation centers in intentionally doped material, as a source of conductivity in nominally undoped material, or as electron–hole recombination centers. Here, the discussion of their concentration and impact has often centered only on formation energies and transition levels. Using hybrid density functional calculations, including the effects of spin–orbit coupling (SOC), we discuss the stability of native point defects in CdTe based on their formation energies and migration barriers. We show that although Cd interstitials are the lowest energy donor defects, they are unstable at room temperature due to a low migration barrier. They are important for maintaining charge neutrality during growth or annealing at high temperatures, but once the material is brought to room temperature, they are not frozen in as often assumed and are expected to anneal out, leaving the other more stable defects to determine the conductivity. Taking this into account in the solution of the charge neutrality equation, we are able to predict the conductivity type and carrier concentrations that are in good agreement with experimental observations.

14 SOLAR ENERGY↗

DOE OSTI2023

Doping Limits of Phosphorus, Arsenic, and Antimony in CdTe

Low p-type doping is a limiting factor to increase CdTe thin-film solar-cell efficiency toward the theoretical Shockley-Queisser limit of 33%. Previous calculations predict relatively high ionization energies for group-V acceptors (P, As, and Sb) and they are plagued by self-compensation, forming AX-centers, severely limiting hole concentration. However, recent experiments on CdTe single crystals indicate a much more favorable scenario, where P, As, and Sb behave as shallow acceptors. Using hybrid functional calculations, we solve this puzzle by showing that the ionization energies significantly decrease with the supercell size. When including the effects of spin-orbit coupling and extrapolating the results to the dilute limit, we find these impurities behave as hydrogenic-like shallow acceptors, and AX-centers are unstable and do not limit ptype doping. We address the differences between our results and previous theoretical predictions and show that our ionization energies predict hole concentrations that agree with recent temperature-dependent Hall measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Imaging CdCl 2 defect passivation and formation in polycrystalline CdTe films by cathodoluminescence

Polycrystalline thin-film solar cells are attractive for low-cost photovoltaics, but their efficiencies are hindered by material quality issues. State-of-the-art CdTe solar cells use CdCl 2 annealing treatments whose effects are still being discovered at a fundamental level. Here, a series of CdTe samples with different annealing temperatures is investigated with high-resolution hyperspectral cathodoluminescence mapping measured at both room temperature and low temperature on the same microscopic areas. A statistical analysis over a large number of grains is combined with a local analysis at grain boundaries. The results elucidate the dynamic interplay between grain boundary and intragrain defect passivation and formation, in the midst of grain growth. The CdCl 2 annealing initially contributes to an increase of the grain size and the passivation of both grain boundaries and grain interiors, increasing the overall luminescence and diffusion length. For higher annealing temperatures, a further increase of grain size is counterbalanced by the rise of bulk defects. The results illustrate the tradeoffs that lead to an optimal annealing temperature, as well as new methods for understanding defect passivation and creation in thin film solar cells.

14 SOLAR ENERGY↗

DOE OSTI2023

12.3% Efficient Lifted-Off and Reconstructed As-Doped CdTe Thin Film Solar Cell

CdTe:As devices grown by MOCVD in the superstrate configuration have been reconfigured to a substrate structure, by employing a cleaving and reconstruction technique. Indium and aluminium doped Zinc oxide (IZO and AZO) layers were used as the transparent front interface without a metal grid. A substrate efficiency of 12.3% was realized with AZO front contact, retaining 80% of the superstrate device efficiency and an impressive approximately 99% of the open-circuit voltage. The IZO-based substrate device on the other hand performed at approximately 69 % retained efficiency. The crucial role of front interfaces is highlighted by the two contacts used here. The results in this work show promise for the development of highly efficient substrate CdTe:As devices.

II-VI semiconductor materials↗

DOE OSTI2023

Human Health Risk Assessment for Improper Landfill Disposal of End-of-Life CdTe PV

chemicals↗

DOE OSTI2026

Understanding Defect Activation and Kinetics in Next Generation CdTe Absorbers

This project investigated the role of defects and dopants in cadmium telluride (CdTe) solar cells to improve efficiency and long-term stability. Advanced X-ray microscopy and spectroscopy techniques were used to map composition, identify defect structures, and measure charge collection at the nanoscale. These experimental results were combined with computational modeling to understand how dopants such as copper and arsenic interact with other elements during processing. The study found that many dopants become electrically inactive due to the formation of complexes with chlorine and oxygen, limiting carrier concentration and device performance. It also showed that selenium, used to enhance efficiency, can migrate within the material during both manufacturing and operation, altering local structure and potentially affecting stability. The project developed new diagnostic and analysis tools for studying photovoltaic materials and provided a mechanistic understanding of key performance limitations. These insights support the development of more efficient, stable, and cost-effective CdTe solar technologies for large-scale energy deployment.

14 SOLAR ENERGY↗

NASA NTRS1987

Determination of a natural valence-band offset - The case of HgTe and CdTe

A method to determine a natural valence-band offset (NVBO), i.e., the change in the valence-band maximum energy which is intrinsic to the bulk band structures of semiconductors is proposed. The HgTe-CdTe system is used as an example in which it is found that the valence-band maximum of HgTe lies 0.35 + or - 0.06 eV above that of CdTe. The NVBO of 0.35 eV is in good agreement with the X-ray photoemission spectroscopy measurement of the heterojunction offset. The procedure to determine the NVBO between semiconductors, and its implication on the heterojunction band lineup and the electronic structures of semiconductor alloys, are discussed.

Shih, C. K.↗

NASA NTRS1988

Experimental ground-based Bridgman CdTe growth in NASA's advanced automated directional solidification furnace

The role of gravity-induced phenomena in bulk CdTe crystal growth is studied with emphasis placed on the negative effects of buoyancy-driven convection, container effects, and hydrostatic pressure. An earth-bound crystal growth data base utilizing NASA's prototype advanced automated directional solidification furnace is described. Growth procedures that can be employed in a microgravity environment aboard the Space Shuttle or Space Station are presented. It is found that NASA's directional solidification furnace can produce Bridgman-type CdTe and has the potential for producing it in space.

Bostrup, G.↗

NASA NTRS1988

Molecular beam epitaxy and metalorganic chemical vapor deposition growth of epitaxial CdTe on (100) GaAs/Si and (111) GaAs/Si substrates

Epitaxial CdTe has been grown on both (100)GaAs/Si and (111)GaAs/Si substrates. A combination of molecular beam epitaxy (MBE) and metalorganic chemical vapor deposition (MOCVD) has been employed for the first time to achieve this growth: the GaAs layers are grown on Si substrates by MBE and the CdTe film is subsequently deposited on GaAs/Si by MOCVD. The grown layers have been characterized by X-ray diffraction, scanning electron microscopy, and photoluminescence.

Nouhi, A.↗

NASA NTRS1989

High-efficiency CdTe thin-film solar cells using metalorganic chemical vapor deposition techniques

Energy conversion efficiency of metalorganic chemical vapor deposited CdTe as an intrinsic active layer in n-i-p solar cell structures is reported. Small-area devices with efficiencies over 9 percent have been demonstrated. I-V characteristics, photospectral response, and the results of Auger profiling of structural composition for typical devices will be presented. Also presented are preliminary results on similar photovoltaic devices having Cd(0.85)Mn(0.15)Te in place of CdTe as an i layer.

Nouhi, A.↗

NASA NTRS1989

Electronic structures of HgTe and CdTe surfaces and HgTe/CdTe interfaces

A Green's-function method has been used to study the surface and interface electronic structures of the II-VI compounds HgTe and CdTe. Localized surface and resonance states near the cation-terminated (100) surface of CdTe and the anion-terminated surface of HgTe have been found for the ideal surfaces. The energies and strengths of these surface states are altered by surface perturbations. The bulk states near the surface are drastically modified by the creation of the surface, but the band gaps remain unchanged. Numerical evaluation of the local densities of states at the Gamma and J points shows that, at the (100) interface of HgTe/CdTe, the previously observed surface states are no longer present. However, in the interface region, bulk states of one material penetrate some distance into the other material.

Schick, J. T.↗