Search NASA⌕ Search

SEARCH · Search NASA

Results for “Composite load model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Fatigue behavior analysis and multi-scale modelling of chopped carbon fiber chip-reinforced composites under tension-tension loading condition

Here, the fatigue damage behavior of chopped carbon fiber chip-reinforced composite has been experimentally and numerically investigated. A large scatter is exhibited in the S-N diagram due to the random distribution of carbon fiber chips, and therefore a new analysis procedure is proposed to link the local microstructure to the fatigue behavior of the bulk material. Interrupted fatigue tests are also performed so that microstructure characterization can be conducted on the tested samples to analyze the crack initiation and propagation. Inspired from the experimental findings, a multi-scale progressive damage fatigue model is proposed to predict the fatigue behavior. The model incorporates a new stochastic chip-packing algorithm for microstructure reconstruction along with continuum damage models into the representative volume element (RVE) model in ABAQUS/Explicit. Finally, the simulation results based on the proposed model are in good agreement with the experimental data in terms of cracking modes and predicted life.

36 MATERIALS SCIENCE↗

Evaluation of Composite Materials for Heliostat Cost Reduction

This is an evaluation of composite materials for heliostat cost reduction, including the motivation, reference heliostat model, characteristic wind loads, selection of pultruded structural composites, and technoeconomic analysis using equivalent deformation.

composite materials↗

Meso-scale modeling and damage analysis of carbon/epoxy woven fabric composite under in-plane tension and compression loadings

The mechanical properties and damage behaviors of carbon/epoxy woven fabric composite under in-plane tension and compression are studied at the meso-scale level through experiment and simulation. An efficient representative volume element (RVE) modeling method with consistent mesh, high yarn volume fraction and realistic geometry is proposed. The material constitutive laws with plasticity, tension-compression asymmetry and damage evolution are established for the three components - yarn, matrix and interface, respectively. Significantly different mechanical properties and damage evolutions are observed depending on loading conditions and initial geometry characteristics. It shows a non-linear stress-strain curve with clear transition region and intensive damage in tension, while a quasi-linear behavior up to facture is observed in compression with little damage prior to final fracture. Furthermore, compared to the constant Poisson's ratio with straining in compression, a dramatic increase in Poisson's ratio appears in tension. Simulation shows damage mechanisms including transverse damage, matrix damage and delamination, which all play critical roles in the property evolution. In particular, the rapid damage accumulation after elastic deformation destroys the strong bonds and causes the easy deformation of transverse yarns which results in the transition region and large Poisson's ratio in tension. All the mechanical behaviors and damage evolutions are well captured and explained with the current RVE model.

42 ENGINEERING↗

Evaluation of some scale effects in the response and failure of composite beams

The feasibility of using scale model testing for predicting full-scale behavior of composite beams loaded in tension and flexure was investigated. Classical laws of similitude were applied to fabricate and test replica model beams to identify scaling effects in the load response, strength, and mode of failure. Experiments were conducted using graphite-epoxy composite beams having different laminate stacking sequences and a range of scaled sizes. Results indicated that the elastic response of scaled composite beams was independent of specimen size. However, a significant scale effect in strength was observed. In addition, a transition in failure mode was observed among scaled beams of certain laminate stacking sequences. Weibull statistical and fracture mechanics based models were applied to predict the strength scale effect since standard failure criteria cannot account for the influence of absolute specimen size in failure.

Jackson, Karen E.↗

RESULTS OF THE FY09 ENHANCED DOE HIGH LEVEL WASTE MELTER THROUGHPUT STUDIES AT SRNL

High-level waste (HLW) throughput (i.e., the amount of waste processed per unit time) is a function of two critical parameters: waste loading (WL) and melt rate. For the Waste Treatment and Immobilization Plant (WTP) at the Hanford Site and the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS), increasing HLW throughput would significantly reduce the overall mission life cycle costs for the Department of Energy (DOE). The objective of this task is to develop data, assess property models, and refine or develop the necessary models to support increased WL of HLW at SRS. It is a continuation of the studies initiated in FY07, but is under the specific guidance of a Task Change Request (TCR)/Work Authorization received from DOE headquarters (Project Number RV071301). Using the data generated in FY07, FY08 and historical data, two test matrices (60 glasses total) were developed at the Savannah River National Laboratory (SRNL) in order to generate data in broader compositional regions. These glasses were fabricated and characterized using chemical composition analysis, X-ray Diffraction (XRD), viscosity, liquidus temperature (TL) measurement and durability as defined by the Product Consistency Test (PCT). The results of this study are summarized below: (1) In general, the current durability model predicts the durabilities of higher waste loading glasses quite well. A few of the glasses exhibited poorer durability than predicted. (2) Some of the glasses exhibited anomalous behavior with respect to durability (normalized leachate for boron (NL [B])). The quenched samples of FY09EM21-02, -07 and -21 contained no nepheline or other wasteform affecting crystals, but have unacceptable NL [B] values (> 10 g/L). The ccc sample of FY09EM21-07 has a NL [B] value that is more than one half the value of the quenched sample. These glasses also have lower concentrations of Al{sub 2}O{sub 3} and SiO{sub 2}. (3) Five of the ccc samples (EM-13, -14, -15, -29 and -30) completely crystallized with both magnetite and nepheline, and still had extremely low NL [B] values. These particular glasses have more CaO present than any of the other glasses in the matrix. It appears that while all of the glasses contain nepheline, the NL [B] values decrease as the CaO concentration increases from 2.3 wt% to 4.3 wt%. A different form of nepheline may be created at higher concentrations of CaO that does not significantly reduce glass durability. (4) The T{sub L} model appears to be under-predicting the measured values of higher waste loading glasses. Trends in T{sub L} with composition are not evident in the data from these studies. (5) A small number of glasses in the FY09 matrix have measured viscosities that are much lower than the viscosity range over which the current model was developed. The decrease in viscosity is due to a higher concentration of non-bridging oxygens (NBO). A high iron concentration is the cause of the increase in NBO. Durability, viscosity and T{sub L} data collected during FY07 and FY09 that specifically targeted higher waste loading glasses was compiled and assessed. It appears that additional data may be required to expand the coverage of the T{sub L} and viscosity models for higher waste loading glasses. In general, the compositional regions of the higher waste loading glasses are very different than those used to develop these models. On the other hand, the current durability model seems to be applicable to the new data. At this time, there is no evidence to modify this model; however additional experimental studies should be conducted to determine the cause of the anomalous durability data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

2016 Update of Hanford Glass Property Models and Constraints for Use in Estimating the Glass Mass to be Produced at Hanford by Implementing Current Enhanced Glass Formulation Efforts

Recent glass formulation and melter testing data have suggested that significant increases in waste loading in high-level waste (HLW) and low-activity waste (LAW) glasses are possible over current system planning estimates. In 2013 a set of models and constraints based on these data were developed and published (Vienna et al. 2013). Since that report roughly 200 additional glasses have been tested and lessons were learned in the application of the preliminary set of models and constraints. This report summarizes the advancements in glass formulation and glass property estimation since Vienna et al. 2013 (using the additional data and lessons learned) and updates the recommended set of enhanced glass property-composition models and constraints for use in River Protection Project (RPP) planning. The combined data (although limited in some cases) were evaluated to determine a set of constraints and models that could be used to estimate the maximum loading of specific waste compositions in glass. It is recommended that these models and constraints be used to estimate the likely HLW and LAW glass masses that would result if the current glass formulation studies are successfully completed. It is recognized that some of the models are preliminary in nature and will change in the coming years. In addition, the models do not currently address the prediction uncertainties that would be required before they could be used in plant operations. The models and constraints are only meant to give an indication of rough glass masses and are not intended to be used in quality-affecting activities or decisions. A current research program is in place to develop the data, models, and uncertainty descriptions for that purpose. A fundamental tenet underlying the research reported in this and the previous document is the attempt to be less conservative, but still realistic, than previous studies when developing constraints for the estimation of glass to be produced by implementing current enhanced glass formulation efforts. The less conservative approach documented herein should allow for the estimate of glass masses that may be realized if the current efforts in enhanced glass formulations are completed over the coming years, and are as successful as early indications suggest they may be. Because of this approach, there is an unquantifiable uncertainty in the ultimate glass mass projections due to model prediction uncertainties that must be considered, along with other system uncertainties, such as waste compositions and amounts to be immobilized, split factors between LAW and HLW, etc. A plan to estimate the impact of those uncertainties has been developed and a future update will document the results.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Micromechanical analysis of filamentary metal matrix composites under longitudinal loading

A two-material composite cylinder model (CCM) was considered for the study of the mechanical behavior at different temperatures of a fiber-reinforced silicon carbide/aluminum (SiC/Al) composite. An elastoplastic analysis of the model was performed in which the fiber was assumed to be linear elastic and the matrix elastoplastic with work-hardening. The analysis was based on the deformation theory of plasticity in conjunction with the von-Mises yield criterion. Experimental stress-strain curves of an SiC/Al composite were obtained at 24 and 288 C (75 and 550 F). The complete three-dimensional stress distribution in the composite using the CCM was determined. It was found that, in addition to longitudinal stresses, transverse stresses in both the fiber and the matrix were developed as a result of the different Poisson's ratios of the two materials. The transverse stresses, although much smaller than the longitudinal stresses, contributed to the plastic deformation of the matrix. The experimental stress-strain curves were favorably compared with the theoretical predictions.

Gdoutos, Emmanuel E.↗

Implementation of Fiber Substructuring Into Strain Rate Dependent Micromechanics Analysis of Polymer Matrix Composites

A research program is in progress to develop strain rate dependent deformation and failure models for the analysis of polymer matrix composites subject to impact loads. Previously, strain rate dependent inelastic constitutive equations developed to model the polymer matrix were incorporated into a mechanics of materials based micromechanics method. In the current work, the micromechanics method is revised such that the composite unit cell is divided into a number of slices. Micromechanics equations are then developed for each slice, with laminate theory applied to determine the elastic properties, effective stresses and effective inelastic strains for the unit cell. Verification studies are conducted using two representative polymer matrix composites with a nonlinear, strain rate dependent deformation response. The computed results compare well to experimentally obtained values.

Goldberg, Robert K.↗

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

Simulation of probabilistic wind loads and building analysis

Probabilistic wind loads likely to occur on a structure during its design life are predicted. Described here is a suitable multifactor interactive equation (MFIE) model and its use in the Composite Load Spectra (CLS) computer program to simulate the wind pressure cumulative distribution functions on four sides of a building. The simulated probabilistic wind pressure load was applied to a building frame, and cumulative distribution functions of sway displacements and reliability against overturning were obtained using NESSUS (Numerical Evaluation of Stochastic Structure Under Stress), a stochastic finite element computer code. The geometry of the building and the properties of building members were also considered as random in the NESSUS analysis. The uncertainties of wind pressure, building geometry, and member section property were qualified in terms of their respective sensitivities on the structural response.

Shah, Ashwin R.↗

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

Thermal Effects on the Compressive Behavior of IM7/PET15 Laminates

The effect of changing operating temperature on the compressive response of IM7/PETI5 composite laminates is investigated within this paper. The three temperatures evaluated for this study were 129 C, 21 C, and 177 C, a spectrum from cryogenic to an elevated operating temperature. Laminate compressive strength property testing was conducted using the Wyoming Combined Load Compression fixture to generate strength data at the three operating temperatures of interest for several lay-ups. A three-dimensional finite element analysis model of a [90/0]8s composite laminate subject to compressive loading is developed. The model is used to study the key attributes of the laminate that significantly influence the state of stress in the laminate. Both the resin rich layer located between lamina and the thermal residual stresses present in the laminate due to curing are included in the analysis model. For the laminate modeled, the effect of modeling temperature dependent material properties was determined to be insignificant for the operating temperatures studied. Simply using the material properties measured at the operating temperature of interest was sufficient for predicting stresses accurately in a linear analysis for the current problem. The three-dimensional analysis results revealed that the application of an applied compressive axial load in the 0-degree direction decreased the interlaminar stresses present in the laminate initially due to curing. Therefore, failure was concluded not be attributable to the interlaminar stresses in the composite laminate being studied when a compressive load is applied. The magnitude of the measured laminate compressive strength change with a change in temperature is concluded to be dominated by the change in the lamina compressive axial strength with a change in temperature.

Walker, Sandra Polesky↗

Test and Analysis Correlation for Sandwich Composite Longitudinal Joint Specimens

The NASA Composite Technology for Exploration (CTE) project is tasked with evaluating methods to analyze and manufacture composite joints for potential use in block upgrades to the Space Launch System (SLS) launch-vehicle structures such as the Payload Attach Fitting (PAF). To perform this task, the CTE project has initiated test and analysis correlation studies for composite joints under various loading conditions. Herein, NASA-developed numerical models are correlated with the experimental results from a series of tension tests. Pretest strain results matched the far-field test data well, but did not capture the nonlinear response in the vicinity of the joint. A refined pretest analytical model was modified to represent progressive failure of the specimens at failure locations observed during the experimental tests. The nonlinear strain response from this progressive failure model predicted the delamination failure load within 15% of the test data, but underpredicted the nonlinearity of the strain response. Further study of composite material models that account for the nonlinear shear response of fabric composites is recommended for the composite joint structures considered in this paper.

Mason, Brian H.↗

Analysis of longitudinal thickness-shear stiffness of a monolayer filamentary composite

The longitudinal thickness-shear behavior of a rectangular cross-section prism containing circular cross-section fibers embedded in a matrix is analyzed. The problem is formulated as a Saint-Venant flexure problem modeled by a tip-loaded cantilever composite beam and solution is obtained by the boundary-point least-squares method. It is shown that the longitudinal thickness-shear modulus is much greater than the in-plane shear modulus for a monofilament composite and therefore an independent analysis is necessary to predict the longitudinal thickness-shear behavior of the composite. Numerical results are presented in graphical form for various values of fiber volume fraction and material parameters typical of modern advanced composites.

Chang, S.↗

Implementation of Laminate Theory Into Strain Rate Dependent Micromechanics Analysis of Polymer Matrix Composites

A research program is in progress to develop strain rate dependent deformation and failure models for the analysis of polymer matrix composites subject to impact loads. Previously, strain rate dependent inelastic constitutive equations developed to model the polymer matrix were implemented into a mechanics of materials based micromechanics method. In the current work, the computation of the effective inelastic strain in the micromechanics model was modified to fully incorporate the Poisson effect. The micromechanics equations were also combined with classical laminate theory to enable the analysis of symmetric multilayered laminates subject to in-plane loading. A quasi-incremental trapezoidal integration method was implemented to integrate the constitutive equations within the laminate theory. Verification studies were conducted using an AS4/PEEK composite using a variety of laminate configurations and strain rates. The predicted results compared well with experimentally obtained values.

Goldberg, Robert K.↗

Test-Free Fracture Toughness

Computational simulation results can give the prediction of damage growth and progression and fracture toughness of composite structures. The experimental data from literature provide environmental effects on the fracture behavior of metallic or fiber composite structures. However, the traditional experimental methods to analyze the influence of the imposed conditions are expensive and time consuming. This research used the CODSTRAN code to model the temperature effects, scaling effects and the loading effects of fiberbraided composite specimens with and without fiber-optic sensors on the damage initiation and energy release rates. The load-displacement relationship and fracture toughness assessment approach is compared with the test results from literature and it is verified that the computational simulation, with the use of established material modeling and finite element modules, adequately tracks the changes of fracture toughness and subsequent fracture propagation for any fiberbraided composite structure due to the change of fiber orientations, presence of large diameter optical fibers, and any loading conditions.

Minnetyan, Levon↗

Test-Free Fracture Toughness

Computational simulation results can give the prediction of damage growth and progression and fracture toughness of composite structures. The experimental data from literature provide environmental effects on the fracture behavior of metallic or fiber composite structures. However, the traditional experimental methods to analyze the influence of the imposed conditions are expensive and time consuming. This research used the CODSTRAN code to model the temperature effects, scaling effects and the loading effects of fiber/braided composite specimens with and without fiber-optic sensors on the damage initiation and energy release rates. The load-displacement relationship and fracture toughness assessment approach is compared with the test results from literature and it is verified that the computational simulation, with the use of established material modeling and finite element modules, adequately tracks the changes of fracture toughness and subsequent fracture propagation for any fiber/braided composite structure due to the change of fiber orientations, presence of large diameter optical fibers, and any loading conditions.

Minnetyan, Levon↗