Search NASA⌕ Search

SEARCH · Search NASA

Results for “Creep resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

MoSi2-Base Composite for Engine Applications

The intermetallic compound MoSi2 has long been known as a high temperature material that has excellent oxidation resistance and electrical/thermal conductivity. Also its low cost, high melting point (2023 C), relatively low density (6.2 g/cm versus 8 g/cm for current engine materials), and ease of machining make it an attractive structural material. However, the use of MoSi2 has been hindered because of the brittle nature of the material at low temperatures, inadequate creep resistance at high temperatures, accelerated oxidation (also known as 'pest' oxidation) at temperatures between approximately 400 and 500 C, and a coefficient of thermal expansion (CTE) that is relatively high in comparison to potential reinforcing fibers such as SiC. This CTE mismatch between the fiber and the matrix resulted in severe matrix cracking during thermal cycling.

Hebsur, Mohan G.↗
NASA NTRS2012

Improvement of GRCop-84 Through the Addition of Zirconium

GRCop-84 (Cu-8 at.% Cr-4 at.% Nb) has excellent strength, creep resistance, low cycle fatigue (LCF) life and stability at elevated temperatures. It suffers in comparison to many commercially available precipitation-strengthened alloys below 500 C (932 F). It was observed that the addition of Zr consistently improved the mechanical properties of Cu-based alloys especially below 500 C. In an effort to improve the low temperature properties of GRCop-84, 0.35 wt.% Zr was added to the alloy. Limited tensile, creep, and LCF testing was conducted to determine if improvements occur. The results showed some dramatic increases in the tensile and creep properties at the conditions tested with the probability of additional improvements being possible through cold working. LCF testing at room temperature did not show an improvement, but improvements might occur at elevated temperatures.

Ellis, David L.↗
NASA NTRS1986

Toughening of BIS maleimide resins: Synthesis and characterization of maleimide terminated poly(arylene ether) oligomers and polymers

Amine functional poly(arylene ether) sulfones were previously reported. Herein, the chemistry was extended to amorphous poly(arylene ether) ketones because of their higher fracture toughness values, relative to the polysulfones. It was demonstrated that the amino functional oligomers undergo a self-crosslinking reaction at temperatures above about 220 C. This produces an insoluble, but ductile network that has excellent resistance. A ketamine structure hypothesis was proposed and verified using solid state magic angle NMR. In most cases, the water generated upon ketamine formation is too low to produce porosity and solid networks are obtained. The stability of the ketamine networks towards hydrolysis is excellent. The chemistry was further demonstrated to be able to crosslink preformed nonfunctional poly(arylene ether) ketones if a difunctional amine was utilized. This concept has the possibility of greatly improving the creep resistance of thermoplastics. Also, a new technique was developed for converting the amine functional oligomers cleanly into maleimide structures. This method involves reacting maleic anhydride with monomeric aminophenols in the presence of solvent mixtures.

Mcgrath, J. E.↗
NASA NTRSDate not supplied

Understanding the Durability of SiC Based Ceramic Matrix Composites (CMCs) for Gas Turbine Engine Hot Section Components

Silicon carbide fiber reinforced silicon carbide ceramic matrix composites (SiCf/SiC-CMCs) are being used in the fabrication of gas turbine engine hot section components due to their light weight and excellent thermal and chemical stabilities at high-temperature. These superior properties enable significant enhancements in engine efficiency and reduced fuel burn, emissions, and cooling requirements. In support of NASA’s Aeronautics Mission under various programs at Glenn Research Center, different types of composites have been developed and assessed for a high temperature (2700 °F) SiCf/SiC CMC system for turbine engine applications. These composites have creep-resistant SiC fibers, advanced 3D weaves, 2700 °F-capable hybrid SiC matrices, and durable environmental barrier coatings (EBCs). These efforts have resulted in improvements in the overall CMC thermomechanical and environmental durability. In order to study the role of different constituents and processing variables, a single fiber tow CVI (chemical vapor infiltration) SiC/SiC mini-composite can be considered the basic architectural feature of woven and laminate SiC/SiC CMCs. Moreover, the mini-composite mechanical and tensile creep damage behavior represents the creep behavior of 0° fiber tows in the axial loading direction of a macro-composite or component. In addition, a large number of mini-composite samples can be fabricated at relatively low cost within a short time, which makes them attractive for obtaining a robust set of experimental data and studying constituent behavior. In this presentation, the mini-composite approach to study damage mechanisms that limit CMC life in extreme environments including exposure to steam will be presented. The effects of constituent type and volume fraction on the CMC durability, which will help influence CMC design, will be discussed.

Ceramic Matrix Composites (CMCs)↗
NASA NTRS2021

Microstructural, Strength, and Creep Characterization of Sylramic™, Sylramic™-iBN and Super Sylramic™-iBN SiC Fibers

The chemical composition, microstructure, strength, and thermal stability of polymer-derived Sylramic™ SiC fibers fabricated by Dow Corning and COI Ceramics, Inc., and nitrogen-treated Sylramic™ SiC fibers, referred to as Sylramic™-iBN and Super Sylramic™-iBN SiC fibers, were investigated and compared. The baseline Sylramic™ SiC fibers fabricated by both vendors as well as the nitrogen-treated Sylramic™ SiC fibers are composed mostly of β-SiC (~97 wt%) with small amounts of TiB2 (~2 wt%), amorphous carbon (~1 wt%) and trace amounts of B4C. Most of the amorphous carbon is segregated at the core/interior of the fibers. Both baseline and nitrogen-treated Sylramic™ SiC fibers have similar grain size and pore size distribution, except for a thin layer of in-situ grown crystalline BN (30 to 70 nm) on the surface of Sylramic™-iBN and Super Sylramic™-iBN fibers. Wide variation in strength within a batch as well as between batches is observed in both baseline and nitrogen-treated Sylramic™ SiC fibers but both types of fibers are microstructurally stable at temperatures to 1800°C in argon and nitrogen environments compared to Nicalon™-S and Tyranno®-SA SiC fibers. Under the same creep condition, Super Sylramic™-iBN fibers show better creep resistance compared to Sylramic™, Sylramic™-iBN, Hi-Nicalon™-S, and Tyranno®-SA fibers. Possible reasons for strength variability and the mechanism of in-situ BN formation on Sylramic™ SiC fibers are discussed.

SiC fibers↗
NASA NTRS2002

Robust Low Cost Liquid Rocket Combustion Chamber by Advanced Vacuum Plasma Process

Next-generation, regeneratively cooled rocket engines require materials that can meet high temperatures while resisting the corrosive oxidation-reduction reaction of combustion known as blanching, the main cause of engine failure. A project was initiated at NASA-Marshal Space Flight Center (MSFC) to combine three existing technologies to build and demonstrate an advanced liquid rocket engine combustion chamber that would provide a 100 mission life. Technology developed in microgravity research to build cartridges for space furnaces was utilized to vacuum plasma spray (VPS) a functional gradient coating on the hot wall of the combustion liner as one continuous operation, eliminating any bondline between the coating and the liner. The coating was NiCrAlY, developed previously as durable protective coatings on space shuttle high pressure fuel turbopump (HPFTP) turbine blades. A thermal model showed that 0.03 in. NiCrAlY applied to the hot wall of the combustion liner would reduce the hot wall temperature 200 F, a 20% reduction, for longer life. Cu-8Cr-4Nb alloy, which was developed by NASA-Glenn Research Center (GRC), and which possesses excellent high temperature strength, creep resistance, and low cycle fatigue behavior combined with exceptional thermal stability, was utilized as the liner material in place of NARloy-Z. The Cu-8Cr-4Nb material exhibits better mechanical properties at 650 C (1200 F) than NARloy-Z does at 538 C (1000 F). VPS formed Cu-8Cr-4Nb combustion chamber liners with a protective NiCrAlY functional gradient coating have been hot fire tested, successfully demonstrating a durable coating for the first time. Hot fire tests along with tensile and low cycle fatigue properties of the VPS formed combustion chamber liners and witness panel specimens are discussed.

Holmes, Richard↗
NASA NTRSDate not supplied

Molecular dynamics simulation of effects of solutes on dislocation propagation in Ni-based superalloys

Ni-based superalloys are used in the hot sections of jet turbine engines because of their high strength, stability and resistance to oxidation. The properties of these alloys can be further optimized by adding alloying elements. Therefore, a fundamental knowledge on the effect of different elements on properties of Ni-based superalloys is required. Molecular dynamics simulation could shed light here but its application is hindered by the absence of reliable and computationally cheap semi-empirical potential of the interatomic interaction for 4 and more element alloys. We will present a new Ni-Al-Cr-Nb Finnis-Sinclair (FS) potential specially designed to simulate the dislocation propagation from to  phase. In order to construct this potential, we designed a special algorithm to incorporate the data on element partitioning in the potential development procedure. For example, it is known from experiment, that Cr is mostly present in the gamma phase. Figure 1 shows a snapshot obtained after equilibration of the model of the Ni68Al17Cr15 alloy at T=1000 K using the hybrid Monte-Carlo (MC)/molecular dynamics (MD) simulation with the developed semi-empirical potential. One can clearly see that the Cr partitioning is in agreement with the experimental data. We will discuss the developed algorithm to incorporate the solute partition data in details. Using the developed semi-empirical potential, we first investigated the effect of anti-site defects in the  phase on the single dislocation propagation. It was found that the dislocation velocity increases with the increasing of the anti-site defect concentration. This effect was attributed to smaller number of Al-Al pairs forming during the dislocation migration in the presence of the anti-site defects. Next, we investigated the effect of Nb on the dislocation pair propagation in the Kolbe mechanism. It was found that the addition of Nb leads to considerable decrease in the dislocation propagation rate. This is in agreement with the experimental data on the effect of Nb on the creep resistance of the Ni-based superalloys. We will discuss the origin of this effect.

Mikhail I. Mendelev↗
NASA NTRS1970

High-strength magnetic materials

Two new precipitation-hardened magnetic alloys are suitable for operation in 800 to 1600 deg F range. One is a martensitic alloy and the other a cobalt-based alloy. They possess improved creep resistance and have application in high temperature inductors and alternators.

Detert, K.↗
NASA NTRS1973

Further characterization of Closed Pore Insulation (CPI)

The thermophysical and mechanical properties of closed pore insulation (CPI) were measured after exposure to 25 simulated reentry thermal cycles. In addition, mechanical properties were obtained at elevated temperatures before and after cycling. The properties of CPI were not compromised by the cycling. High temperature creep studies were done on three CPI compositions (4, 8, and 12 Wt% CoO additive). CPI-4 had the best creep resistance at temperatures up to 1363 K.

Russak, M.↗
NASA NTRS1973

Correlation of creep rate with microstructural changes during high temperature creep

The techniques of electron microscopy were used to examine the microstructural changes which occur during primary creep for two important types of engineering alloys: (1) alloys strengthened by solid-solution additions, and (2) dispersion-strengthened alloys. The metals chosen for study are unalloyed titanium, Ti-6Al-4V, and the cobalt-base alloy, Haynes 188. Results to date on NGR 47-004-108 show that development of prior dislocation substructure in Haynes 188 by 10% prestrain and annealing for one hour at 1800 F increases the time to reach 0.5% creep strain at 1600 F by more than an order of magnitude for creep stresses from 3 to 20 ksi. For creep at 1800 F, similar results were obtaind for stresses above 7 ksi, but the prior substructure decreases creep resistance below 7 ksi. This effect appears to be related to instability of grain structure at 1800 F in prestrained material.

Young, C. T.↗
NASA NTRS1975

Seals

Seal configurations generally found in fluid systems are given. Special attention is given to material selection and the process for achieving a seal. Seal material characteristics including wear resistance, creep, and cold flow properties are discussed.

Source record↗
NASA NTRS1975

The elastic modulus correction term in creep activation energies Applied to oxide dispersion strengthened superalloy

The effect of elastic modulus and the temperature dependence of elastic modulus on creep activation energies for an oxide dispersion strengthened nickel-base superalloy are investigated. This superalloy is commercially known as Inconel Alloy MA 753, strengthened both by gamma-prime precipitates and by yttria particles. It is shown that at intermediate temperatures, say below 1500 F, where elastic modulus is weakly dependent on temperature, the modulus correction term to creep activation energy is small. Accordingly, modulus corrections are insignificant for the superalloy considered, which shows high apparent creep activation energies at this temperature. On the contrary, at very high temperatures, the elastic modulus correction term can be significant, thus reducing the creep activation energy to that of vacancy self-diffusion. In order to obtain high-temperature creep resistance, a high-value elastic modulus with a weak dependence on temperature is required.

Malu, M.↗
NASA NTRS1976

The metallurgy of high temperature alloys

Nickel-base, cobalt-base, and high nickel and chromium iron-base alloys are dissected, and their microstructural and chemical components are assessed with respect to the various functions expected of high temperature structural materials. These functions include the maintenance of mechanical integrity over the strain-rate spectrum from creep resistance through fatigue crack growth resistance, and such alloy stability expectations as microstructural coarsening resistance, phase instability resistance and oxidation and corrosion resistance. Special attention will be given to the perennial conflict and trade-off between strength, ductility and corrosion and oxidation resistance. The newest developments in the constitution of high temperature alloys will also be discussed, including aspects relating to materials conservation.

Tien, J. K.↗
NASA NTRS1977

Alloy design with oxide dispersoids and precipitates

The mechanical behavior of particle-strengthened alloys is reviewed. On the basis of this knowledge, it is concluded that second-phase particles, coherent or incoherent, can enhance the flow strength, creep resistance, and stress-rupture life of alloys. Unfortunately, particles are usually not beneficial alloy-design elements if enhanced uniaxial ductility, plane-strain ductility, stress-rupture ductility, and toughness are called for. Such properties as fatigue-crack propagation resistance appear to require, for example, both high strength and high ductility, a situation which can come to pass only when the perennial conflict between strength and ductility is resolved in particle-strengthened systems in particular and in any other material system in general. Wherever possible, the role of coherent and incoherent particles in alloy design is distinguished.

Tien, J. K.↗
NASA NTRS1981

New pressure-sensitive silicone adhesive

Adhesive for high or low temperatures does not stretch severely under load. It is produced by combining intermediate-molecular-weight pressure sensitive adhesive which does not cure with silicone resin that cures with catalyst to rubbery tack-free state. Blend of silicone tackifier and cured rubbery silicone requires no solvents in either atmospheric or vacuum environments. Ratio of ingredients varies for different degrees of tack, creep resistance, and tensile strength.

Leiffer, J. L.↗
NASA NTRS1980

Thermal decomposition of a Si3N4-22 wt% Al2O3 alloy

It is pointed out that materials near the Si3N4 corner of the Si3N4-AlN-Al2O3-SiO2 quaternary, termed sialons are candidate materials for high performance applications. Hot pressed alloys in this system are useful because they possess high flexure strengths and good oxidation and creep resistance. The results of the thermal decomposition studies conducted indicate that dissociation and resulting weight loss lead to inhomogeneous specimens. Material loss comes primarily from near the surface (at least initially) thus causing differences between the composition of the surface material and the bulk. In these specimens, the O-prime phase was found to be the least stable to dissociation and the beta-prime phase the most stable. This result is in accord with the conclusions of Mitomo et al. (1979) that Si2N2O has a larger equilibrium SiO partial pressure than either the X phase or the beta-prime phase.

Ditchek, B. M.↗