Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cutouts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Blended Cutout Flap for Reduction of Jet-Flap Interaction Noise

An aircraft system includes a wing and a trailing edge device coupled to the wing. The trailing edge device is movable relative to the wing, and includes a leading edge and a trailing edge having a center flap portion and a plurality of outer edge portions integrally combined with the center flap portion such that the center flap portion is shorter in width than that of outer edge portions.

Czech, Michael J↗
NASA NTRSDate not supplied

GeoNEX-SUBSETS: Cutouts of geostationary satellite data over long-term monitoring sites

Satellite remote sensing data are important tool for extrapolating the knowledge obtained at the Fluxnet towers. We introduce our GEO-NEX geostationary satellite subset products, which make it easy to compare between ground observation and Geo-NEX products. The MODIS subset has been frequently used for validating ecosystem models developed at flux towers and upscaling the observed flux data to regional scales. However, MODIS on the polar orbiting satellites can observe target regions only once a day, while the Fluxnet eddy-covariance data are compiled as sub-hourly datasets. As a results, summarizing the sub-hourly flux data into daily statistics is necessary for the comparison between MODIS and Flux data. Here, the new generation geostationary satellite sensors (GOES-16/17 ABI and Himawari-8/9 AHI) has the high-frequent observation feature (10 minutes) in addition to similar spectral band and spatial resolution with MODIS. The high frequent observation allows us to compare the flux diurnal cycle with geostationary satellite sensor data. Some studies have already shown the effective utilization of time series of geostationary satellite data for ecosystem modeling. We are producing NEX Level-1G products, which is the gridded Top-of-Atmosphere reflectance and brightness temperature data of geostationary satellite sensors. We cut out the NEX Level-1G data using the same file format with the MODIS subset except for the projection. The other data products (e.g., surface reflectance, land surface temperature, vegetation indices and climate data) will be also added upon their availability. We selected the ground observation sites from Fluxnet, Phenocam, and AERONET networks. The NEX subset data will be provided through NASA NEX data portal.

GeoNEX↗
NASA NTRS1979

Computer design synthesis of a below knee-Syme prosthesis

A detailed design synthesis analysis of the BK Syme prosthesis is provided, to determine the socket's cutout orientation size and shape, cutout fillet shape, socket wall thickness distribution and the reinforced fiber distribution in the socket wall, for a minimally stressed structurally safe lightweight prosthesis. For analysis purposes, the most adverse socket loading is obtained at the push-off stage of gait; this loading is idealized as an axial in-plane loading on the bottom edge of the circular cylindrical socket shell whose top edge is considered fixed. Finite element stress analysis of the socket shell (with uniform and graded wall thickness) are performed for various orientations of the cutout and for various types of corner fillets. A lateral cutout with a streamline fillet is recommended. The wall material (i.e., thickness) distribution is determined so as to minimize the stresses, while ensuring that the wall material's stress limits are not exceeded. For such a maximally stressed lightweight socket shell, the panels in the neighborhood of the cutout are checked to ensure that they do not buckle under their acquired stresses. A fiber-reinforced laminated composite socket shell is also analyzed in order to recommend optimum variables in orientations and densities of reinforcing fibers.

Elangovan, P. T.↗
NASA NTRS1978

Finite element stress analysis of idealized composite damage zones

A quasi three dimensional finite element stress analysis of idealized damage zones in composite laminates is presented. The damage zones consist of a long centered groove or cutout extending one or two layers in depth from both top and bottom surfaces of a thin composite laminate. Elastic results are presented for compressive loading of four and eight layer laminates. It is shown that a boundary layer exists near the cutout edge similar to that previously shown to exist along free edges. The cutout is shown to produce significant interlaminar stresses in the interior of the laminate away from free cutout edges. The interlaminar stresses are also shown to contribute to failure which is defined using the Tsai-Wu failure criteria.

Obrien, D.↗
NASA NTRS1989

Subcomponent tests for composite fuselage technology readiness

An account is given of a NASA research effort aimed at the development of an all-composite transport aircraft fuselage incorporating joints and cutouts which meets all design requirements. The design, construction, and analysis activities associated with the 30-ft-long fuselage section gave attention to critically important subcomponent specimens, including shear-tee pulloff specimens, stiffened and unstiffened cutout panels, longitudinal and transverse skin splices, longeron runouts, transverse skin-longerons, stiffened shear panels, and window belt panels. The analysis of large cutouts was conducted with coupling FEM analyses incorporating accurate failure criteria for tension and shear; the strategic application of S2 glass fiber plies around cutouts was demonstrated both analytically and experimentally to increase load capacity with virtually no weight penalty.

Madan, R. C.↗
NASA NTRS1953

Experimental Stress Analysis of Stiffened Cylinders with Cutouts.pure Torsion

Torsion tests were made on a cylindrical semimonocoque shell of circular cross section. The cylinder was first tested without a cutout, and then with a rectangular cutout which was successively enlarged through six sizes varying from 30 degrees to 130 degrees in circumference and from 1 to 2 bays in length. Strain measurements were made with resistance-type wire strain gages near the cutout on the stringers, the skin, and the rings for each size of cutout, and the stresses obtained are presented in tables. (author)

LOADS AND STRESSES, STRUCTURAL - TORSION↗
NASA NTRS1995

Low-speed longitudinal aerodynamic characteristics through poststall for 21 novel planform shapes

To identify planform characteristics which have promise for a highly maneuverable vehicle, an investigation was conducted in the Langley Subsonic Basic Research Tunnel to determine the low-speed longitudinal aerodynamics of 21 planform geometries. Concepts studied included twin bodies, double wings, cutout wings, and serrated forebodies. The planform models tested were all 1/4-in.-thick flat plates with beveled edges on the lower surface to ensure uniform flow separation at angle of attack. A 1.0-in.-diameter cylindrical metric body with a hemispherical nose was used to house the six-component strain gauge balance for each configuration. Aerodynamic force and moment data were obtained across an angle-of-attack range of 0 to 70 deg with zero sideslip at a free-stream dynamic pressure of 30 psf. Surface flow visualization studies were also conducted on selected configurations using fluorescent minitufts. Results from the investigation indicate that a cutout wing planform can improve lift characteristics; however, cutout size, shape, and position and wing leading-edge sweep will all influence the effectiveness of the cutout configuration. Tests of serrated forebodies identified this concept as an extremely effective means of improving configuration lift characteristics; increases of up to 25 percent in the value of maximum lift coefficient were obtained.

Gatlin, Gregory M.↗
NASA NTRSDate not supplied

TPSAS-NF1676L-26160-DND

The structural performance of two advanced composite tow-steered shells is assessed using experiments and analyses. The fiber angles vary continuously around the shell circumference, and one shell has all 24 tows applied during fabrication, while the second shell uses the fiber placement systems tow drop/add capability to achieve a uniform wall thickness. The shells are tested in compression, and their axial stiffnesses and buckling loads are estimated using linear finite element analyses. Scaled passenger and cargo door cutouts are machined into one side of each shell. Axial stiffnesses and buckling loads of the shells with cutouts are computed using linear finite element analyses. The retested shells carry over 90 percent of the axial stiffness, and 85 percent of the buckling loads, of the shells without cutouts. These small reductions demonstrate the potential of tow steering to mitigate adverse effects of cutouts on the structural performance. The good correlation between experimental buckling loads and linear buckling analyses noted here may result from their circumferential stiffness variation, reducing geometric imperfection sensitivity. Analysis models of both shells were evaluated without and with measured geometric imperfections superposed in different longitudinal orientations. Small variations in prebuckling stiffness and buckling load of the shells are observed.

K C Wu↗
DOE OSTI2025

The Mantis Shrimp Dataset

The Mantis Shrimp Dataset (MSD) is a combination of matched cutouts of galaxies with known redshift in the ultra-violet, optical, and infrared wavelengths. MSD redshifts come from ''high-quality'' (as reported by the spectroscopic experiment) redshift measurements from a variety of spectroscopic surveys, including: SDSS, DESI early release, DEEP2, GAMA, VVDS, VIPERS, 6dF, and WiggleZ. Each redshift is accompanies with astrometry (ra,dec) pairs that were used to query cutout image services from PanSTARRs, UnWISE, and GALEX servers. The main data products are image vectors of these cutouts accompanied by the redshift value to be used to train computer vision networks on the supervised photometric redshift task. We also provide extinction values pre-queried at each galaxies' astrometry from the PLANCK and SFD dutstmaps, the SDSS MGS photometric redshift from Beck 2014 (if available) and the WISE x PS1 STRM photometric redshift for the galaxy (if available).

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1971

Analysis of transient, linear wave propagation in shells by the finite difference method

The applicability of the finite difference method to propagation problems in shells, and the response of a cylindrical shell with cutouts to both longitudinal and radial transient excitations are investigated. It is found that the only inherent limitation of the finite difference method is its inability to reproduce accurately response discontinuities. The short wave length limitations of thin shell theory create significant convergence difficulties may often be overcome through proper selection of finite difference mesh dimensions and temporal or spatial smoothing of the excitation. Cutouts produce moderate changes in early and intermediate time response of a cylindrical shell to axisymmetric pulse loads applied at one end. The cutouts may facilitate the undesirable late-time transfer of load-injected extensional energy into nonaxisymmetric flexural response.

Geers, T. L.↗
NASA NTRS1993

A probabilistic method for the buckling assessment of stiffened composite shells

A method is described to computationally simulate probabilistic buckling behavior of multilayered composite shells. The simulation accounts for all naturally-occurring uncertainties including those in constituent (fiber/matrix) material properties, fabrication variables, and structure geometry. The method is demonstrated for probabilistically assessing the buckling survivability of a specific case of a stiffened composite cylindrical shell with and without cutouts. The sensitivities of various uncertain variables on the buckling survivability are evaluated at specified reliability. The results show that the buckling survivability for a shell without cutouts depends primarily on shell skin related uncertainties. However, stringer related uncertainties become important for a shell with cutouts.

Shiao, Michael C.↗
NASA NTRS1999

Development of Analysis Methods for Designing with Composites

The project involved the development of new analysis methods to achieve efficient design of composite structures. We developed a complex variational formulation to analyze the in-plane and bending coupling response of an unsymmetrically laminated plate with an elliptical cutout subjected to arbitrary edge loading as shown in Figure 1. This formulation utilizes four independent complex potentials that satisfy the coupled in-plane and bending equilibrium equations, thus eliminating the area integrals from the strain energy expression. The solution to a finite geometry laminate under arbitrary loading is obtained by minimizing the total potential energy function and solving for the unknown coefficients of the complex potentials. The validity of this approach is demonstrated by comparison with finite element analysis predictions for a laminate with an inclined elliptical cutout under bi-axial loading.The geometry and loading of this laminate with a lay-up of [-45/45] are shown in Figure 2. The deformed configuration shown in Figure 3 reflects the presence of bending-stretching coupling. The validity of the present method is established by comparing the out-of-plane deflections along the boundary of the elliptical cutout from the present approach with those of the finite element method. The comparison shown in Figure 4 indicates remarkable agreement. The details of this method are described in a manuscript by Madenci et al. (1998).

Madenci, E.↗
DOE OSTI2024

Localized phase contrast imaging at the Wendelstein 7-X stellarator

In its basic form, phase contrast imaging (PCI) provides line-integrated measurements of electron density fluctuations in plasmas. As turbulent fluctuations in magnetically confined plasmas have wave vectors almost perpendicular to the background magnetic field, the signals scattered by fluctuations from different parts of the PCI line-of-sight (LoS) are spatially separated in focal planes of the plasma. This allows localized PCI measurements by placing a mask in such a plane, to only permit signals from specific parts of the LoS to reach the PCI detectors. The present paper describes modeling and design of localization masks for the PCI system at the Wendelstein 7-X (W7-X) stellarator as well as the first results obtained using the masks in the recent long-pulse W7-X experimental campaign. During this project, we have extended the theory describing the mask response within the Fraunhofer diffraction model. As a novel development, we show from first principles that the mask response is determined by the fraction of power of the scattered beam spots that passes the mask. These insights have been used to select the W7-X mask design, consisting of a circular cutout, allowing the unscattered beam spot to pass the mask, with wedges covering a fixed angular range outside the central cutout. In the recent W7-X experimental campaign, the masks have verified the location of the main turbulence features observed by the PCI system and provided new information about the location of short-wavelength magnetohydrodynamic modes.

Physics↗