Search NASA⌕ Search

SEARCH · Search NASA

Results for “Direct Drive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

A Lightweight, Direct-Drive, Fully Superconducting Generator for Large Wind Turbines

The current trend in the offshore wind turbine industry favors direct-drive generators based on permanent magnets, as they allow for a simple and reliable drivetrain without a gearbox. These generators, however, do not scale very well to high power levels beneficial for offshore wind, and their use in wind turbines over 6 MW is questionable in terms of mass and economic feasibility. Moreover, rare earth materials composing the permanent magnets are becoming less available, more costly and potentially unavailable in the foreseeable future. A stated goal of the DOE is a critical materials strategy that pursues the development of substitute materials and technology for rare earth materials to improve supply chain flexibility and meet the needs of the clean energy economy.Therefore, alternative solutions are needed, in terms of both favorable up-scaling and minimizing or eliminating the use of permanent magnets. The generator design presented in this document addresses both these issues with the development of a fully superconducting generator (FSG) with unprecedented high specific torque. A full-scale, 10-MW, 10-rpm generator will weigh less about 150 metric tons, compared to 300 metric tons for an equivalent direct-drive, permanent magnet generator. The developed concept does not use any rare earth materials in its critical drive components, but rather relies on a superconductor composed of mainly magnesium and boron (MgB2), both of which are in abundant supply from multiple global sources.

17 WIND ENERGY↗

Adaptive Fuzzy Control of a Direct Drive Motor: Experimental Aspects

This paper presents a state feedback adaptive control method for position and velocity control of a direct drive motor. The proposed control scheme allows for integrating heuristic knowledge with mathematical knowledge of a system. It performs well even when mathematical model of the system is poorly understood. The controller consists of an adaptive fuzzy controller and a supervisory controller. The supervisory controller requires only knowledge of the upper bound and lower bound of the system parameters. The fuzzy controller is based on fuzzy basis functions and states of the system. The adaptation law is derived based on the Lyapunov function which ensures that the state of the system asymptotically approaches zero. The proposed controller is applied to a direct drive motor with payload and parameter uncertainty, and the effectiveness is experimentally verified. The real-time performance is compared with simulation results.

Medina, E.↗

Plasma Interactions with High Voltage Solar Arrays for a Direct Drive Hall Effect Thruster System

The Environmental Effects Group of NASA s Marshall Space Flight Center (MSFC) is conducting research into the effects of plasma interaction with high voltage solar arrays. These high voltage solar arrays are being developed for a direct drive Hall Effect Thruster propulsion system. A direct drive system configuration will reduce power system mass by eliminating a conventional power-processing unit. The Environmental Effects Group has configured two large vacuum chambers to test different high-voltage array concepts in a plasma environment. Three types of solar arrays have so far been tested, an International Space Station (ISS) planar array, a Tecstar planar array, and a Tecstar solar concentrator array. The plasma environment was generated using a hollow cathode plasma source, which yielded densities between 10(exp 6) - 10(exp 7) per cubic centimeter and electron temperatures of 0.5-1 eV. Each array was positioned in this plasma and biased in the -500 to + 500 volt range. The current collection was monitored continuously. In addition, the characteristics of arcing, snap over, and other features, were recorded. Analysis of the array performance indicates a time dependence associated with the current collection as well as a tendency for "conditioning" over a large number of runs. Mitigation strategies, to reduce parasitic current collection, as well as arcing, include changing cover-glass geometry and layout as well as shielding the solar cell edges. High voltage performance data for each of the solar array types tested will be presented. In addition, data will be provided to indicate the effectiveness of the mitigation techniques.

Schneider, T.↗

Absolute stimulated Raman side scatter in direct-drive laser-produced plasmas

Production of suprathermal electrons by stimulated Raman scattering (SRS) is a principal concern for contemporary direct-drive inertial confinement fusion experiments at the National Ignition Facility and similar systems since such electrons penetrate and preheat the target core, preventing efficient implosion. The higher temperatures and longer scale lengths in these experiments favor SRS over two-plasmon decay, which predominated in earlier experiments. In particular, current experiments are expected to exceed the threshold for absolute Raman side scatter, which would then dominate the interaction since it grows temporally until saturated by nonlinear mechanisms such as hot-electron production. Until recently, analyses of SRS side scatter have treated the case of a single laser beam incident on a plasma, but the direct-drive approach to laser fusion employs a multitude of beams to drive the implosion. Here in this paper, we present an analysis that can be applied to an arbitrary number of beams with varied angles of incidence and polarizations. In the case of a single beam, it allows a physically motivated derivation and verification of an analytic threshold formula. In the general case of multiple beams and arbitrary orientation and polarizations, the threshold is found by numerical integration of a set of first-order linear partial differential equations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Design Considerations of a Transverse Flux Machine for Direct-Drive Wind Turbine Applications

This paper presents the design considerations of a double-sided transverse flux machine (TFM) for direct-drive wind turbine applications. The proposed TFM has a modular structure with quasi-U stator cores and toroidal ring windings. The rotor is constructed with ferrite magnets in a flux-concentrating setup to achieve high air gap flux density. Pole number selection is critical in the design process of a TFM as it affects both the torque density and power factor under fixed magnetic and changing electrical loading. Several key design ratios are introduced to facilitate the initial design procedure. The effect of pole shaping on back-EMF and inductance is also analyzed. These investigations provide guidance toward the required design of a TFM for direct-drive applications. The analyses are carried out using analytical and three-dimensional finite element analysis (FEA). A proof-of-concept prototype was developed to experimentally validate the FEA results.

17 WIND ENERGY↗

Test of a Novel, Commercial-Scale Wave Energy Direct-Drive Rotary Power Take-Off at the NREL National Wind Technology Center (CRADA CRD-14-571 Final Report)

The National Renewable Energy Laboratory (NREL) will work with Columbia Power Technologies [C-Power] to support work under US DOE DE-EE-0006399, “Build and Test of a Novel, Commercial-Scale Wave Energy Direct-Drive Rotary Power Take-Off Under Realistic Open-Ocean Conditions.” Work will include a review of their design for a novel wave energy direct drive generator. After review, the system will be prototyped and tested in the NREL National Wind Technology Center (NWTC) 5MW dynamometer and data will be recorded and analyzed. Conclusions from data analysis will be used to improve the design prior to completing a version of the system for ocean deployment. Additionally, NREL will work with Columbia Power Technologies [C-Power] to quantify the system levelized cost of energy (LCOE) and analyze the system in agreement with US DOE System Performance Advancement (SPA) goals 1 and 2.

16 TIDAL AND WAVE POWER↗

Direct-drive DT implosions with Knudsen number variations

Direct-drive implosions of DT-filled plastic-shells have been conducted at the Omega laser facility, measuring nuclear yields while varying Knudsen numbers (i.e., the ratio of mean free path of fusing ions to the length of fuel region) by adjusting both shell thickness (e.g., 7.5, 15, 20, 30 μm) and fill pressure (e.g., 2, 5, 15 atm). In addition, the fusion reactivity reduction model showed a stronger effect on yield as the Knudsen number increases (or the shell thickness decreases). The Reduced-Ion-Kinetic (RIK) simulation which includes both fusion reactivity reduction and mix model was necessary to provide a better match between the observed neutron yields and those simulated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Laser-Beam Zooming to Mitigate Crossed-Beam Energy Losses in Direct-Drive Implosions

In this study, spherically symmetric direct-drive-ignition designs driven by laser beams with a focal-spot size nearly equal to the target diameter suffer from energy losses due to crossed-beam energy transfer (CBET). Significant reduction of CBET and improvements in implosion hydrodynamic efficiency can be achieved by reducing the beam diameter. Narrow beams increase low-mode perturbations of the targets because of decreased illumination uniformity that degrades implosion performance. Initiating an implosion with nominal beams (equal in size to the target diameter) and reducing the beam diameter by ~ 30% - 40% after developing a sufficiently thick target corona, which smooths the perturbations, mitigate CBET while maintaining low-mode target uniformity in ignition designs with a fusion gain >> 1.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Numerical analysis of the direct drive illumination uniformity for the Laser MegaJoule facility

The illumination uniformity provided during the initial imprinting phase of the laser foot pulse in a direct drive scenario at the Laser MegaJoule facility has been analyzed. This study analyzes the quality of the illumination of a spherical capsule and concerns the uniformity of the first shock generate in the absorber of an Inertial Confinement Fusion capsule. Four configurations making use of all or some of the 80 laser beams organized in the 20 quads of the cones at 49° and 131° with respect to the polar axis have been considered in order to assemble the foot pulse. Elliptical and circular super-gaussian laser intensity profiles taking into account beam-to-beam power imbalance (10%), pointing error (50 μm), and target positioning (20 μm) have been considered. It has been found that the use of the Polar Direct Drive technique can in some cases reduce the irradiation non-uniformity by a factor as high as 50%. In all cases, elliptical profile provides better results in comparison with the circular one and it is shown that the minimum of the non-uniformity is also a function of the capsule radius.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Demonstration of fuel hot-spot pressure in excess of 50 Gbar for direct-drive, layered deuterium-tritium implosions on OMEGA

A record fuel hot-spot pressure P hs = 56±7 Gbar was inferred from x-ray and nuclear diagnostics for direct-drive inertial confinement fusion cryogenic, layered deuterium–tritium implosions on the 60-beam, 30-kJ, 351-nm OMEGA Laser System. When hydrodynamically scaled to the energy of the National Ignition Facility (NIF), these implosions achieved a Lawson parameter ~60% of the value required for ignition [A. Bose et al., Phys. Rev. E (in press)], similar to indirect-drive implosions [R. Betti et al., Phys. Rev. Lett. 114, 255003 (2015)], and nearly half of the direct-drive ignition-threshold pressure. Relative to symmetric, one-dimensional simulations, the inferred hot-spot pressure is ~40% lower. Furthermore, three-dimensional simulations suggest that low-mode distortion of the hot spot seeded by laser-drive nonuniformity and target-positioning error reduces target performance.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Self-generated magnetic fields in the hot spot of direct-drive cryogenic implosions at Omega

This work reports that Biermann self-generated magnetic fields of ≈200 MG and Hall parameters of ≈1.5 are produced in the stagnation phase of direct-drive cryogenic implosions at Omega. The magnetic fields produce a drop of 2.4% in fusion yield and 1% in ion temperature. A quantitative estimate of the effect of self-generated magnetic fields on yield and ion temperature is essential, since direct measurements of these fields are not available. Reconstructed simulations of the 50 Gbar implosions, with all the stagnation measurements reproduced simultaneously by a combination of mid- and low-mode asymmetries as degradation mechanisms [Bose et al., Phys. Plasmas 25, 062701 (2018)], are used to obtain the estimates. The magnetic fields cause a decrease in yield due to the Righi–Leduc heat flow, which exceeds any benefits from heat flow suppression due to magnetization. It is important to note that both direct-drive Omega-scale implosions and indirect-drive National Ignition Facility (NIF)-scale implosions [Walsh et al., Phys. Rev. Lett. 118, 155001 (2017)] produce similar estimates for the magnetic field strength, and both show a decrease in fusion yield, with the Righi–Leduc transport as the loss mechanism. However, the yield degradation at Omega is small and lower by ≈5× compared to the indirect-drive ignition-scale NIF estimate.

Physics↗

Thermally Simulated Testing of a Direct-Drive Gas-Cooled Nuclear Reactor

This paper describes the concept and preliminary component testing of a gas-cooled, UN-fueled, pin-type reactor which uses He/Xe gas that goes directly into a recuperated Brayton system to produce electricity for nuclear electric propulsion. This Direct-Drive Gas-Cooled Reactor (DDG) is designed to be subcritical under water or wet-sand immersion in case of a launch accident. Because the gas-cooled reactor can directly drive the Brayton turbomachinery, it is possible to configure the system such that there are no external surfaces or pressure boundaries that are refractory metal, even though the gas delivered to the turbine is 1144 K. The He/Xe gas mixture is a good heat transport medium when flowing, and a good insulator when stagnant. Judicious use of stagnant cavities as insulating regions allows transport of the 1144-K gas while keeping all external surfaces below 900 K. At this temperature super-alloys (Hastelloy or Inconel) can be used instead of refractory metals. Super-alloys reduce the technology risk because they are easier to fabricate than refractory metals, we have a much more extensive knowledge base on their characteristics, and, because they have a greater resistance to oxidation, system testing is eased. The system is also relatively simple in its design: no additional coolant pumps, heat exchanger, or freeze-thaw systems are required. Key to success of this concept is a good knowledge of the heat transfer between the fuel pins and the gas, as well as the pressure drop through the system. This paper describes preliminary testing to obtain this key information, as well as experience in demonstrating electrical thermal simulation of reactor components and concepts.

Godfroy, Thomas↗

Experimental Investigation of a Direct-drive Hall Thruster and Solar Array System at Power Levels up to 10 kW

As NASA considers future exploration missions, high-power solar-electric propulsion (SEP) plays a prominent role in achieving many mission goals. Studies of high-power SEP systems (i.e. tens to hundreds of kilowatts) suggest that significant mass savings may be realized by implementing a direct-drive power system, so NASA recently established the National Direct-Drive Testbed to examine technical issues identified by previous investigations. The testbed includes a 12-kW solar array and power control station designed to power single and multiple Hall thrusters over a wide range of voltages and currents. In this paper, single Hall thruster operation directly from solar array output at discharge voltages of 200 to 450 V and discharge powers of 1 to 10 kW is reported. Hall thruster control and operation is shown to be simple and no different than for operation on conventional power supplies. Thruster and power system electrical oscillations were investigated over a large range of operating conditions and with different filter capacitances. Thruster oscillations were the same as for conventional power supplies, did not adversely affect solar array operation, and were independent of filter capacitance from 8 to 80 ?F. Solar array current and voltage oscillations were very small compared to their mean values and showed a modest dependence on capacitor size. No instabilities or anomalous behavior were observed in the thruster or power system at any operating condition investigated, including near and at the array peak power point. Thruster startup using the anode propellant flow as the power 'switch' was shown to be simple and reliable with system transients mitigated by the proper selection of filter capacitance size. Shutdown via cutoff of propellant flow was also demonstrated. A simple electrical circuit model was developed and is shown to have good agreement with the experimental data.

Snyder, John S.↗

Mitigating laser-imprint effects in direct-drive inertial confinement fusion implosions with an above-critical-density foam layer

Low-density foams of low-/mid-Z materials have been previously proposed to mitigate laser imprint for direct-drive inertial confinement fusion (ICF). For foam densities above the critical density of the drive laser, the mechanism of laser-imprint mitigation relies on the reduced growth rate of Rayleigh–Taylor instability because of the increased ablation velocity and density scale length at the ablation surface. Experimental demonstration of this concept has been limited so far to planar-target geometry. The impact of foams on spherical implosions has not yet been explored in experiments. To examine the viability of using an above-critical-density foam layer to mitigate laser-imprint effects in direct-drive ICF implosions on OMEGA, we have performed a series of 2-D DRACO simulations with state-of-the-art physics models, including nonlocal thermal transport, cross-beam energy transfer, and first-principles equation-of-state tables. The simulation results indicate that a 40-μm-thick CH or SiO 2 foam layer with a density of p = 40 mg/cm 3 added to a D2-filled polystyrene (CH) capsule can significantly improve the moderate-adiabat (α ≈ 3) implosion performance. In comparison with the standard CH target implosion, an increase of neutron yield by a factor of 4 to 8 and the recovery of 1-D compression pR are predicted by DRACO simulations for a foam-target surface roughness of σ rms ≤ 0.5 μm. These encouraging results could readily facilitate experimental demonstrations of laser-imprint mitigation with an above-critical-density foam layer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Exploration of cross-beam energy transfer mitigation constraints for designing an ignition-scale direct-drive inertial confinement fusion driver

The compression of direct-drive inertial confinement fusion (ICF) targets is strongly impacted by cross-beam energy transfer (CBET), a laser-plasma instability that limits ablation pressure by redirecting laser energy outward and that is projected to be mitigated by laser bandwidth. Here, we explore various CBET mitigation constraints to guide the design of future ICF facilities. First, we find that the flat, Gaussian, and Lorentzian spectral shapes have similar CBET mitigation properties, and a flat shape with nine spectral lines is a good surrogate for what can be obtained with other spectral shapes. Then, we conduct a comprehensive study across energy scales and ignition designs. 3D hydrodynamic simulations are used to derive an analytical model for the expected CBET mitigation as a function of laser and plasma parameters. From this model, we study the bandwidth requirements of conventional and shock ignition designs across four different energy scales and find that they require between 0.5 and 3±0.2% relative bandwidth. Further, best mitigation is achieved when the beam radius over critical radius R b /R c is kept low during the drive while the plasma temperature is kept high. In a steady state, we find that the bandwidth required to mitigate 85% of CBET scales as (R b /R c ) 2.15 L n –0.58 I 0.7 , where L n is the density scale length, and I the laser intensity. Finally, we find that the chamber beam port layout does not influence CBET mitigation. In the case of a driver using many monochromatic beamlets, we find that ~10 beamlets per port is required, with diminishing returns above ~20.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct-drive laser fusion: status, plans and future

Laser-direct drive (LDD), along with laser indirect (X-ray) drive (LID) and magnetic drive with pulsed power, is one of the three viable inertial confinement fusion approaches to achieving fusion ignition and gain in the laboratory. The LDD programme is primarily being executed at both the Omega Laser Facility at the Laboratory for Laser Energetics and at the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory. LDD research at Omega includes cryogenic implosions, fundamental physics including material properties, hydrodynamics and laser–plasma interaction physics. LDD research on the NIF is focused on energy coupling and laser–plasma interactions physics at ignition-scale plasmas. Limited implosions on the NIF in the ‘polar-drive’ configuration, where the irradiation geometry is configured for LID, are also a feature of LDD research. The ability to conduct research over a large range of energy, power and scale size using both Omega and the NIF is a major positive aspect of LDD research that reduces the risk in scaling from OMEGA to megajoule-class lasers. Furthermore, the paper will summarize the present status of LDD research and plans for the future with the goal of ultimately achieving a burning plasma in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Core conditions for alpha heating attained in direct-drive inertial confinement fusion

It is shown that direct-drive implosions on the OMEGA laser have achieved core conditions that would lead to significant alpha heating at incident energies available on the National Ignition Facility (NIF) scale. The extrapolation of the experimental results from OMEGA to NIF energy assumes only that the implosion hydrodynamic efficiency is unchanged at higher energies. This approach is independent of the uncertainties in the physical mechanism that degrade implosions on OMEGA, and relies solely on a volumetric scaling of the experimentally observed core conditions. It is estimated that the current best-performing OMEGA implosion [Regan et al., Phys. Rev. Lett. 117, 025001 (2016)] extrapolated to a 1.9 MJ laser driver with the same illumination configuration and laser-target coupling would produce 125 kJ of fusion energy with similar levels of alpha heating observed in current highest performing indirect-drive NIF implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Subpercent-Scale Control of 3D Low Modes of Targets Imploded in Direct-Drive Configuration on OMEGA

In a series of direct-drive implosions on OMEGA, multiple time resolved x-ray images were used to tomographically measure their 3-D modes 1, 2, and 3 at a convergence ratio of ~3. Results show that the target modes vary linearly with the laser modes and are not affected by the Rayleigh–Taylor growth or lateral heat transport. This indicates that the residual modes (resulting from physical effects including beam mistiming, mispointing, and laser energy calibration) are approximately constant between shots. Lastly, this demonstrates that the low-mode amplitudes can be mitigated within by adjusting the laser-energy balance to compensate the residual target modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗