Search NASA⌕ Search

SEARCH · Search NASA

Results for “Distributed temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Velocity and temperature distributions of coal-slag layers on magnetohydrodynamic generators walls

Approximate analytical expressions are derived for the velocity and temperature distributions in steady state coal slag deposits flowing over MHD generator walls. Effects of slag condensation and Joule heating are included in the analysis. The transport conditions and the slag temperature at the slag-gas interface are taken to be known parameters in the formulation. They are assumed to have been predetermined either experimentally or from the slag properties and the gas dynamic calculations of the free stream flow. The analysis assumes a power law velocity profile for the slag and accounts for the coupling between the energy and momentum conservation equations. Comparisons are made with the more exact numerical solutions to verify the accuracy of the results.

Pian, C. C. P.↗
NASA NTRS1997

Effect of Velocity and Temperature Distribution at the Hole Exit on Film Cooling of Turbine Blades

An existing three-dimensional Navier-Stokes code (Arnone et al, 1991), modified Turbine Branch, to include film cooling considerations (Garg and Gaugler, 1994), has been used to study the effect of coolant velocity and temperature distribution at the hole exit on the heat transfer coefficient on three film-cooled turbine blades, namely, the C3X vane, the VKI rotor, and the ACE rotor. Results are also compared with the experimental data for all the blades. Moreover, Mayle's transition criterion (1991), Forest's model for augmentation of leading edge heat transfer due to free-stream turbulence (1977), and Crawford's model for augmentation of eddy viscosity due to film cooling (Crawford et al, 1980) are used. Use of Mayle's and Forest's models is relevant only for the ACE rotor due to the absence of showerhead cooling on this rotor. It is found that, in some cases, the effect of distribution of coolant velocity and temperature at the hole exit can be as much as 60 percent on the heat transfer coefficient at the blade suction surface, and 50 percent at the pressure surface. Also, different effects are observed on the pressure and suction surface depending upon the blade as well as upon the hole shape, conical or cylindrical.

Garg, V. K.↗
NASA NTRS1972

Pyrometer for measurement of surface temperature distribution on a rotating turbine blade.

A conceptual optical method and some test results are presented for measuring the surface temperature distribution on one of the rotating turbine blades with a surface resolution of 0.05 cm spot diameter at a tip speed of 400 m/sec. The blade is scanned line-by-line by a fixed optical system. During each line-scan, the detector analog output signal is converted to 200 consecutive digital values that are temporarily stored in a high-speed buffer memory and then transferred at a slower rate to a computer for processing. The signal-to-noise ratio of the silicon avalanche detector is large enough to obtain an accuracy of 1% at 1050 K blade temperature. By averaging 25 scans of the same line the same accuracy can be obtained at 900 K.

Buchele, D. R.↗
NASA NTRS1972

Pyrometer for measurement of surface temperature distribution on a rotating turbine blade

A conceptual optical method and some test results are presented for measuring the surface temperature distribution on one of the rotating turbine blades with a surface resolution of 0.05 cm spot diameter at a tip speed of 400 m/sec. The blade is scanned line-by-line by a fixed optical system. During each line-scan, the detector analog output signal is converted to two hundred consecutive digital values that are temporarily stored in a high speed buffer memory, and then transferred at a slower rate to a computer for processing. The signal-to-noise ratio of the silicon avalanche detector is large enough to obtain an accuracy of one percent at 1050 K blade temperature. By averaging 25 scans of the same line the same accuracy can be obtained at 900 K.

Buchele, D. R.↗
NASA NTRS1972

Wall temperature distribution calculation for a rocket nozzle contour

The JANNAF turbulent boundary layer (TBL) computer program, applicable to rocket nozzles, requires a wall temperature distribution among other input parameters to determine boundary layer behavior, heat transfer, and performance degradation. The inclusion of a complete regenerative cooling cycle model with associate geometry, material and fluid property data provides a capability to internally calculate wall temperature profiles on the hot gas and coolant flow-side, as well as the coolant flow bulk temperature variation. Besides the regular heat transfer and performance degradation calculations, the new concept can be used to optimize the cooling cycle, flow requirements, and cooling jacket geometry.

Omori, S.↗
NASA NTRS1977

Computation of the temperature distribution in cooled radial inflow turbine guide vanes

A two-dimensional finite-difference numerical technique is presented to determine the temperature distribution of an internally-cooled blade of radial turbine guide vanes. A simple convection cooling is assumed inside the guide vane. Such an arrangement results in relatively small cooling effectiveness at the leading edge and at the trailing edge. Heat transfer augmentation in these critical areas may be achieved by using impingement jets and film cooling. A computer program is written in Fortran IV for IBM 370/165 computer.

Tabakoff, W.↗
NASA NTRS1947

Preliminary Results of an Altitude-Wind-Tunnel Investigation of a TG-100A Gas Turbine-Propeller Engine: Pressure and Temperature Distributions - 3

An altitude-wind-tunnel investigation of a TG-100A gas turbine-propeller engine was performed. Pressure and temperature data were obtained at altitudes from 5000 to 35000 feet, compressor inlet ram-pressure ratios from 1.00 to 1.17, and engine speeds from 800 to 13000 rpm. The effect of engine speed, shaft horsepower, and compressor-inlet ram-pressure ratio on pressure and temperature distribution at each measuring station are presented graphically.

Geisenheyner, Robert M.↗
NASA NTRS1936

The Effect of Baffles on the Temperature Distribution and Heat-transfer Coefficients of Finned Cylinders

This report presents the results of an investigation to determine the effect of baffles on the temperature distribution and the heat-transfer coefficient of finned cylinders. The tests were conducted in a 30-inch wind tunnel on electrically heated cylinders with fins of 0.25 and 0.31 inch pitch. The results of these tests showed that the use of integral baffles gave a reduction of 31.9 percent in the rear wall temperatures and an increase of 54.2 percent in the heat transfer coefficient as compared with a cylinder without baffles.

Schey, Oscar W↗
NASA NTRS1972

Approximate temperature distribution for a diffuse, highly reflecting material.

The application of a 'two-flux' technique is considered for determining the reflective characteristics and approximate temperature distribution in highly backscattering materials characterized by a very small absorption coefficient. With respect to the transmitted internal radiation fields, the internal radiative emission is assumed to be negligible. A comparison of theory and experiment is presented.

Weston, K. C.↗
NASA NTRS1977

Numerical solution for the temperature distribution in a cooled guide vane blade of a radial gas turbine

A two dimensional finite difference numerical technique is presented to determine the temperature distribution of an internal cooled blade of radial turbine guide vanes. A simple convection cooling is assumed inside the guide vane blade. Such cooling has relatively small cooling effectiveness at the leading edge and at the trailing edge. Heat transfer augmentation in these critical areas may be achieved by using impingement jets and film cooling. A computer program is written in FORTRAN IV for IBM 370/165 computer.

Hosny, W. M.↗
NASA NTRS1987

Determination of the cross-sectional temperature distribution and boiling limitation of a heat pipe

A computer model is developed and verified which is capable of determining the cross-sectional temperature distribution within a heat pipe with an attached radiator fin; such heat pipes would be plugged into contact heat exchangers designed to carry heat from a space station habitation module to the radiator elements through a centralized fluid loop. The model can furnish information for determining the susceptibility of the monogroove heat pipe to boiling, as well as the location and magnitude of that boiling.

Peterson, G. P.↗
NASA NTRS1995

Temperature Distributions in Semitransparent Coatings: A Special Two-Flux Solution

Radiative transfer is analyzed in a semitransparent coating on an opaque substrate and in a semitransparent layer for evaluating thermal protection behavior and ceramic component performance in high temperature applications. Some ceramics are partially transparent for radiative transfer, and at high temperatures internal emission and reflections affect their thermal performance. The behavior is examined for a ceramic component for which interior cooling is not provided. Two conditions are considered: (1) the layer is heated by penetration of radiation from hot surroundings while its external surface is simultaneously film cooled by convection, and (2) the surface is heated by convection while the semitransparent material cools from within by radiant emission leaving through the surface. By using the two-flux method, which has been found to yield good accuracy in previous studies, a special solution is obtained for these conditions. The analytical result includes isotropic scattering and requires only an integration to obtain the temperature distribution within the semitransparent material. Illustrative results are given to demonstrate the nature of the thermal behavior.

Siegel, Robert↗
NASA NTRS1971

Steady-state temperature distribution in living tissue modeled as cylindrical shells.

Closed form, analytical solutions to the problem of steady-state heat transfer in living tissue modeled as cylindrical shells are presented and discussed. These solutions are particularly useful for the study of temperature distributions in the extremities. Metabolic heat generation, conduction, and heat transported by the blood perfusing the tissue are considered in the model. The results demonstrate the important role that the blood stream plays in the transfer of heat inside living tissue. Solutions are also presented for the limiting cases of diminishing blood flow that would occur during vasoconstriction or occlusion of blood by external means.

Shitzer, A.↗
NASA NTRS1978

Experimental temperature distribution and heat load characteristics of rotating heat pipes

Experimental results show conclusively that the presence of a small quantity of a noncondensable gas (NCG) mixed with the working fluid has a considerable effect on the condensation process in a rotating heat pipe. The temperature distribution in the condenser shows the blanketing effect of the NCG and the ratio of the molecular weight of the working fluid to that of the NCG has a very definite effect on the shape of this distribution. Some of the effects are quite similar to the well-established data on stationary heat pipes.

Daniels, T. C.↗