Search NASA⌕ Search

SEARCH · Search NASA

Results for “ELASTIC BAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Finite element modeling of stress in the Nazca plate - Driving forces and plate boundary earthquakes

The state of stress within the Nazca plate due to plate driving forces and large plate boundary earthquakes has been analyzed by applying a finite element method using the wave front solution technique to models of the intraplate stress field in a single plate using a refined grid. Although only static elastic models have been explicitly calculated, certain limiting cases of an elastic plate over a viscous asthenosphere were also treated. A state of nearly east-west compression inferred from the source mechanism of thrust earthquakes in the interior of the plate requires ridge pushing forces. The net pulling force on the oceanic plate by the subducted slab has a maximum value comparable to pushing forces. The estimated horizontal deviatoric stress in intraplate regions, based on potential forces associated with the ridge, is on the order of a few hundred bars. The intraplate stress field in the region of the 1960 earthquake may change by a few tens of bars at most once the asthenosphere has relaxed, with changes on the order of one bar occurring at greater distances into the plate. The changes in the intraplate stress field are probably not noticeable unless the lithosphere is near failure.

Richardson, R. M.↗
NASA NTRS1993

Nondestructive Characterization of the Elastic Constants of Fiber Reinforced Composites

Composite structural components may be subjected to a variety of defects resulting in a sharp reduction in their load carrying capacity or even catastrophic failure...A nondestructive method based on ultrasonics has recently been developed for the quantitative evaluation of composite structural components during service...In this paper the method is applied to determine the stiffness constants of unidirectional graphite/epoxy materials.

composites↗
NASA NTRS2001

Multiplexed ultrasonic system

A system which rapidly determines the elastic stiffness constants of materials in plate shape as well as characterize material flaws that are affecting these constants. Rapid (below a minute) nondestructive evaluation system allow for the determination of material stiffness constants, low noise data acquisition algorithm for measuring spectral data. A real time method of displaying leaky Lamb wave spectral data.

Bar-Cohen, Yoseph↗
NASA NTRS2020

Composite Piezoelectric Resonator 1D Modeling with Loss

Abstract – Maximizing the benefit of applying piezoelectric materials in composite structures, which are a mix of piezoelectric and elastic elements, requires analytical modeling. In this paper we describe two main classes of resonators and how to model using network equivalent including material losses. These include extensional devices where the layer areas are parallel to the direction of wave travel as found in a variety of thickness or length mode transducers (BC. Stress T1 = T2 at boundary) and transverse mode resonators (BC. Strain S1 = S2 at boundary) where the major layer area is perpendicular to the wave direction as is found in radial mode or length thickness mode composite resonators. In order to illustrate these models we will use Mason’s equivalent circuits with elastic, dielectric and piezoelectric loss. It is noted that in order to maintain consistency with the linear equations of piezoelectricity and the wave equation care is required when applying complex loss coefficients to the models. Although these techniques are applicable to other models we use Mason’s network equivalent circuit because it is intuitive for composite modeling due to the frequency independent turns ratio and the independence of the equations describing the elastic layers from the adjoining layer properties which aids in understanding the boundary conditions to impose on the layer boundaries. We will present network models for a variety of applications with loss and show how to calculate their impedance spectra, interface stress, strain velocity and displacement spectra.

Sherrit, Stewart↗
NASA NTRS1994

Scaling, elasticity, and CLPT

The first few viewgraphs describe the general solution properties of linear elasticity theory which are given by the following two statements: (1) for stress B.C. on S(sub sigma) and zero displacement B.C. on S(sub u) the altered displacements u(sub i)(*) and the actual stresses tau(sub ij) are elastically dependent on Poisson's ratio nu alone: thus the actual displacements are given by u(sub i) = mu(exp -1)u(sub i)(*); and (2) for zero stress B.C. on S(sub sigma) and displacement B.C. on S(sub u) the actual displacements u(sub i) and the altered stresses tau(sub ij)(*) are elastically dependent on Poisson's ratio nu alone: thus the actual stresses are given by tau(sub ij) = E tau(sub ij)(*). The remaining viewgraphs describe the minimum parameter formulation of the general classical laminate theory plate problem as follows: The general CLT plate problem is expressed as a 3 x 3 system of differential equations in the displacements u, v, and w. The eighteen (six each) A(sub ij), B(sub ij), and D(sub ij) system coefficients are ply-weighted sums of the transformed reduced stiffnesses (bar-Q(sub ij))(sub k); the (bar-Q(sub ij))(sub k) in turn depend on six reduced stiffnesses (Q(sub ij))(sub k) and the material and geometry properties of the k(sup th) layer. This paper develops a method for redefining the system coefficients, the displacement components (u,v,w), and the position components (x,y) such that a minimum parameter formulation is possible. The pivotal steps in this method are (1) the reduction of (bar-Q(sub ij))(sub k) dependencies to just two constants Q(*) = (Q(12) + 2Q(66))/(Q(11)Q(22))(exp 1/2) and F(*) - (Q(22)/Q(11))(exp 1/2) in terms of ply-independent reference values Q(sub ij); (2) the reduction of the remaining portions of the A, B, and D coefficients to nondimensional ply-weighted sums (with 0 to 1 ranges) that are independent of Q(*) and F(*); and (3) the introduction of simple coordinate stretchings for u, v, w and x,y such that the process is neatly completed.

Brunelle, Eugene J.↗
NASA NTRS1993

Characterization of the Elastic Constants of Unidirectional Laminates Using Oblique-Incidence Pulsed Data

From Intro: In this paper, wer apply the LLW (leaky Lamb Wave) technique to determine the stiffness constants of unnidirectional graphite/epoxy materials...In this paper, we describe a new technique which can be used to determine all five stiffness constants by analyzing the times-of-flight of the recorded reflected acoustic waves in a pulsed LLW experiment.

composites composite components ultrasonics ultras↗
NASA NTRS2006

Ultrasonic/Sonic Driller/Corer (USDC) as a Subsurface Sampler and Sensors Platform for Planetary Exploration Applications

The search for existing or past life in the Universe is one of the most important objectives of NASA's mission. For this purpose, effective instruments that can sample and conduct in-situ astrobiology analysis are being developed. In support of this objective, a series of novel mechanisms that are driven by an Ultrasonic/Sonic actuator have been developed to probe and sample rocks, ice and soil. This mechanism is driven by an ultrasonic piezoelectric actuator that impacts a bit at sonic frequencies through the use of an intermediate free-mass. Ultrasonic/Sonic Driller/Corer (USDC) devices were made that can produce both core and powdered cuttings, operate as a sounder to emit elastic waves and serve as a platform for sensors. For planetary exploration, this mechanism has the important advantage of requiring low axial force, virtually no torque, and can be duty cycled for operation at low average power. The advantage of requiring low axial load allows overcoming a major limitation of planetary sampling in low gravity environments or when operating from lightweight robots and rovers. The ability to operate at duty cycling with low average power produces a minimum temperature rise allowing for control of the sample integrity and preventing damage to potential biological markers in the acquired sample. The development of the USDC is being pursued on various fronts ranging from analytical modeling to mechanisms improvements while considering a wide range of potential applications. While developing the analytical capability to predict and optimize its performance, efforts are made to enhance its capability to drill at higher power and high speed. Taking advantage of the fact that the bit does not require rotation, sensors (e.g., thermocouple and fiberoptics) were integrated into the bit to examine the borehole during drilling. The sounding effect of the drill was used to emit elastic waves in order to evaluate the surface characteristics of rocks. Since the USDC is driven by piezoelectric actuation mechanism it can designed to operate at extreme temperature environments from very cold as on Titan and Europa to very hot as on Venus. In this paper, a review of the latest development and applications of the USDC will be given.

sampling↗
NASA NTRS1996

Measuring the Thickness and Elastic Properties of Electroactive Thin-Film Polymers Using Platewave Dispersion Data

Electroactive thin-film polymers are candidate sensors and actuators materials. They are also finding significant potential in muscle mechanisms and microelectromechanical systems (MEMS). In these applications, polymer thin films of thickness varying between 20 and 300 micrometers are utilized. The authors are currently studying the potential use of platewave dispersion curve measurements as an effective gauging tool for electroactive thin-film polymers.

sensors actuators film thickness measurements piez↗
NASA NTRS1994

Ultrasonic Evaluation of Thermal Degradation in Adhesive Bonds

The critical role played by adhesive bonds in lap joints is well known. A good knowledge of the mechanical properties of adhesive bonds in lap joints is a prerequisite to the design and reliable prediction of the performance of these bonded structures. Furthermore, the lap joint may be subject to high-temperature environments in service. Early detection of the degree of thermal degradation in adhesive bonds is required under these circumstances. A variety of ultrasonic nondestructive evaluation (NDE) techniques can be used to determine the thickness and the elastic moduli of adhesively bonded joints. In this paper we apply a previously developed technique based on the leaky Lamb wave (LLW) experiment to investigate the possibility of characterizing the thermal degradation of adhesive bonds in lap joints. The degradation of the adhesive bonds is determined through comparison between experimental data and theoretical calculations.

degradation lap joints mechanical properties bonde↗
NASA NTRS1997

(abstract) Oblique Insonification Ultrasonic NDE of Composite Materials for Space Applications

In recent years, a great deal of research has been exerted to developing NDE methods for the characterization of the material properties of composites as well as other space structural materials. The need for information about such parameters as the elastic properties, density, and thickness are critical to the safe design and operation of such structural materials. Ultrasonics using immersion methods has played an important role in these efforts due to its capability, cost effectiveness, and ease of use. The authors designed a series of ultrasonic oblique insonification experiments in order to develop a practical field applicable NDE method for space structures.

ultrasonic composites nondestructive evaluation ND↗
NASA NTRS1992

Equations of motion of slung-load systems, including multilift systems

General simulation equations are derived for the rigid body motion of slung-load systems. This work is motivated by an interest in trajectory control for slung loads carried by two or more helicopters. An approximation of these systems consists of several rigid bodies connected by straight-line cables or links. The suspension can be assumed elastic or inelastic. Equations for the general system are obtained from the Newton-Euler rigid-body equations with the introduction of generalized velocity coordinates. Three forms are obtained: two generalize previous case-specific results for single-helicopter systems with elastic and inelastic suspensions, respectively; and the third is a new formulation for inelastic suspensions. The latter is derived from the elastic suspension equations by choosing the generalized coordinates so that motion induced by cable stretching is separated from motion with invariant cable lengths, and by then nulling the stretching coordinates to get a relation for the suspension forces. The result is computationally more efficient than the conventional formulation, is readily integrated with the elastic suspension formulation, and is easily applied to the complex dual-lift and multilift systems. Results are given for two-helicopter systems; three configurations are included and these can be integrated in a single simulation. Equations are also given for some single-helicopter systems, for comparison with the previous literature, and for a multilift system. Equations for degenerate-body approximations (point masses, rigid rods) are also formulated and results are given for dual-lift and multilift systems. Finally, linearlized equations of motion are given for general slung-load systems are presented along with results for the two-helicopter system with a spreader bar.

Cicolani, Luigi S.↗
NASA NTRS1981

Fracture toughness of brittle materials determined with chevron notch specimens

Short bar, short rod, and four-point-bend chevron-notch specimens were used to determine the plane strain fracture toughness of hot-pressed silicon nitride and sintered aluminum oxide brittle ceramics. The unique advantages of this specimen type are: (1) the production of a sharp natural crack during the early stage of test loading, so that no precracking is required, and (2) the load passes through a maximum at a constant, material-independent crack length-to-width ratio for a specific geometry, so that no post-test crack measurement is required. The plane strain fracture toughness is proportional to the maximum test load and functions of the specimen geometry and elastic compliance. Although results obtained for silicon nitride are in good mutual agreement and relatively free of geometry and size effects, aluminum oxide results were affected in both these respects by the rising crack growth resistance curve of the material.

Shannon, J. L., Jr.↗
NASA NTRS1993

Nondestructive characterization of the elastic constants of fiber reinforced composites

Composite structural components may be subjected to a variety of defects resulting in a sharp reduction in their load carrying capacity or even catastrophic failure. Thus, it is extremely important to have the means to monitor the degradation suffered by critical components of a structure for safe operation during its service life. A nondestructive method based on ultrasonics has recently been developed for the quantitative evaluation of composite structural components during service. The experimental part of the technique uses a two-transducer, pitch-catch type arrangement to generate a variety of elastic waves within the specimen immersed in water. The recorded reflection data are then analyzed by means of a theoretical model to back out the relevant properties. In this paper the method is applied to determine the stiffness constants of unidirectional graphite/epoxy materials. The measurements are shown to be efficient and sufficiently accurate so that it can be used for early detection of material degradation in composite structural elements during service.

Mal, Ajit K.↗
NASA NTRS1999

Coal Thickness Gauging Using Elastic Waves

The efforts of a mining crew can be optimized, if the thickness of the coal layers to be excavated is known before excavation. Wave propagation techniques can be used to estimate the thickness of the layer based on the contrast in the wave velocity between coal and rock beyond it. Another advantage of repeated wave measurement is that the state of the stress within the mine can be estimated. The state of the stress can be used in many safety-related decisions made during the operation of the mine. Given these two advantages, a study was carried out to determine the feasibility of the methodology. The results are presented herein.

Nazarian, Soheil↗
NASA NTRS2020

Elastic wave analyzer for icy sub-surfaces (EWAIS) in water-bearing worlds

In this paper, we discuss the current status of the development of an elastic wave analyzer for icy sub-surface (EWAIS). We begin with an introductory overview of the necessity to develop an active elastic wave transmitter that will enable reaching distances of kilometer thru ice. It is being developed to be driven by piezoelectric transducers with a bouncing constrained mass that impacts a transmission head. The EWAIS transmits the waves at two distinct frequencies; the primary frequency at ~10 kHz for high resolution, and the secondary converted low frequency (LF) in the range of 100 to 500 Hz for long distance transmission. Sonar equation was used for the estimation of required source level, and an impact force sensor is used for the performance measurement of EWAIS prototype.

Lee, Hyeong Jae↗
NASA NTRS1999

Composite Materials NDE Using Enhanced Leaky Lamb Wave Dispersion Data Acquisition Method

The leaky Lamb wave (LLW) technique is approaching a maturity level that is making it an attractive quantitative NDE tool for composites and bonded joints. Since it was first observed in 1982, the phenomenon has been studied extensively, particularly in composite materials. The wave is induced by oblique insonification using a pitch-catch arrangement and the plate wave modes are detected by identifying minima in the reflected spectra to obtain the dispersion data. The wave behavior in multi-orientation laminates has been well documented and corroborated experimentally with high accuracy. The sensitivity of the wave to the elastic constants of the material and to the boundary conditions led to the capability to measure the elastic properties of bonded joints. Recently, the authors significantly enhanced the LLW method's capability by increasing the speed of the data acquisition, the number of modes that can be identified and the accuracy of the data inversion. In spite of the theoretical and experimental progress, methods that employ oblique insonification of composites are still not being applied as standard industrial NDE methods. The authors investigated the issues that are hampering the transition of the LLW to industrial applications and identified 4 key issues. The current capability of the method and the nature of these issues are described in this paper.

Bar-Cohen, Yoseph↗
NASA NTRS2012

Wideband Single-Crystal Transducer for Bone Characterization

The microgravity conditions of space travel result in unique physiological demands on the human body. In particular, the absence of the continual mechanical stresses on the skeletal system that are present on Earth cause the bones to decalcify. Trabecular structure decreases in thickness and increases in spacing, resulting in decreased bone strength and increased risk of injury. Thus, monitoring bone health is a high priority for long-term space travel. A single probe covering all frequency bands of interest would be ideal for such measurements, and this would also minimize storage space and eliminate the complexity of integrating multiple probes. This invention is an ultrasound transducer for the structural characterization of bone. Such characterization measures features of reflected and transmitted ultrasound signals, and correlates these signals with bone structure metrics such as bone mineral density, trabecular spacing, and thickness, etc. The techniques used to determine these various metrics require measurements over a broad range of ultrasound frequencies, and therefore, complete characterization requires the use of several narrowband transducers. This is a single transducer capable of making these measurements in all the required frequency bands. The device achieves this capability through a unique combination of a broadband piezoelectric material; a design incorporating multiple resonator sizes with distinct, overlapping frequency spectra; and a micromachining process for producing the multiple-resonator pattern with common electrode surfaces between the resonators. This device consists of a pattern of resonator bars with common electrodes that is wrapped around a central mandrel such that the radiating faces of the resonators are coplanar and can be simultaneously applied to the sample to be measured. The device operates as both a source and receiver of acoustic energy. It is operated by connection to an electronic system capable of both providing an excitation signal to the transducer and amplifying the signal received from the transducer. The excitation signal may be either a wide-bandwidth signal to excite the transducer across its entire operational spectrum, or a narrow-bandwidth signal optimized for a particular measurement technique. The transducer face is applied to the skin covering the bone to be characterized, and may be operated in through-transmission mode using two transducers, or in pulse-echo mode. The transducer is a unique combination of material, design, and fabrication technique. It is based on single-crystal lead magnesium niobate lead titanate (PMN-PT) piezoelectric material. As compared to the commonly used piezoceramics, this piezocrystal has superior piezoelectric and elastic properties, which results in devices with superior bandwidth, source level, and power requirements. This design necessitates a single resonant frequency. However, by operating in a transverse length-extensional mode, with the electric field applied orthogonally to the extensional direction, resonators of different sizes can share common electrodes, resulting in a multiply-resonant structure. With carefully sized resonators, and the superior bandwidth of piezocrystal, the resonances can be made to overlap to form a smooth, wide-bandwidth characteristic.

Liang, Yu↗
NASA NTRS2020

Elastic wave analyzer for icy sub-surfaces (EWAIS) in the solar system

The sub-surface structures of water-bearing icy worlds (e.g., Europa, Enceladus, and Titan) and the structures of icy regions on Mars contain critical information about their origin and evolution. These bodies have been identified as high-priority targets in the NRC Planetary Science Decadal Survey, which noted a lack of technology readiness as one impediment to related missions. An Elastic Wave Analyzer for Icy Sub-surfaces (EWAIS) instrument is being developed to acquire data that can provide answers to fundamental science questions related to these bodies. The EWAIS instrument generates and receives elastic waves using an array of piezoelectric transducers capable of operating at temperatures as low as 30K. A developed breadboard acquires reflected signals from discontinuities in the traveled materials’ impedance (the product of wave velocity and density) along the wave path. Analysis of the acquired data can be used to determine the elastic properties, presence of cracks, locations of cavities and other discontinuities, as well as the thicknesses of ice and liquid layers. The EWAIS instrument is being developed with a novel dual-frequency transmitter array that will enable reaching distances of kilometers through ice, as well as resolving smaller acoustic reflectors nearer the EWAIS instrument. The selected dual frequencies correspond to two depth ranges that can be analyzed, with resolutions of tens of centimeters in the region of tens to hundreds of meters and tens of meters on the kilometers scale, respectively. The EWAIS will be applicable for operation from any in-situ platform, including surface assets (e.g., lander and rover) and sub-surface assets (e.g., melting probes).

Bar-Cohen, Y.↗