Search NASA⌕ Search

SEARCH · Search NASA

Results for “EXIT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Control of exit velocity profile of an asymmetric annular diffuser using wall suction

An asymmetric annular diffuser equipped with wall bleed (suction) capability was tested for controllability of exit velocity profile. The diffuser area ratio was 3.2, and the length to inlet height ratio was 1.6. Results show that the diffuser radial exit velocity profile could be controlled from a hub peaked to a tip peaked form by selective use of bleed on the outer wall or on both diffuser walls. Based on these results, application of the diffuser bleed technique to gas turbine combustors may be possible. Diffuser bleed could be used to tailor the airflow distribution for optimizing combustor performance at a variety of operating conditions.

Juhasz, A. J.↗

The effect of exit conditions on the development of an axisymmetric turbulent free jet

The mean flow in the near field of a submerged axisymmetric jet emitting from a plane wall is presented. An experimental configuration to provide a nearly uniform mean velocity profile with a core of homogeneous turbulence of variable intensity and scale was developed. Eight cases with intensity values of 0.004 less than or equal to U prime less than or equal to 0.035 and integral scales up to l sub x/R = 0.28 were investigated using conditional sampling techniques. It was found that the jet exhibits an increasing momentum flux in the near field. Contrary to expectation and the accepted assumption of ambient static pressure in a turbulent jet, results seem to be conclusive and borne out by comparison with published data. Both integral measures, mass and momentum flux ratios, are insensitive to exit turbulence variations, but, the detailed structure (including centerline velocity) variations with exit conditions are systematic and explainable.

Kleis, S. J.↗

Sound propagation through a subsonic jet due to a source near the duct exit

Matched asymptotic solutions are constructed for the acoustic potentials of a periodic point source located in a two-dimensional subsonic jet near the exit of the duct with the ratio of the duct thickness to the acoustic wave length as the small parameter. The leading term of the far field solution has the same directionality effect as that for an infinite jet without the duct and that when the plane at the duct exit is considered to be a plane of symmetry. However, the intensity is different because of the wave propagation into the duct and is dependent on the location of the source.

Ting, L.↗

Design, durability and low cost processing technology for composite fan exit guide vanes

A lightweight composite fan exit guide vane for high bypass ratio gas turbine engine application was investigated. Eight candidate material/design combinations were evaluated by NASTRAN finite element analyses. A total of four combinations were selected for further analytical evaluation, part fabrication by two ventors, and fatigue test in dry and wet condition. A core and shell vane design was chosen in which the unidirectional graphite core fiber was the same for all candidates. The shell material, fiber orientation, and ply configuration were varied. Material tests were performed on raw material and composite specimens to establish specification requirements. Pre-test and post-test microstructural examination and nondestructive analyses were conducted to determine the effect of material variations on fatigue durability and failure mode. Relevant data were acquired with respect to design analysis, materials properties, inspection standards, improved durability, weight benefits, and part price of the composite fan exit guide vane.

Blecherman, S. S.↗

Turbojet-exhaust-nozzle secondary-airflow pumping as an exit control of an inlet-stability bypass system for a Mach 2.5 axisymmetric mixed-compression inlet

The throat of a Mach 2.5 inlet that was attached to a turbojet engine was fitted with large, porous bleed areas to provide a stability bypass system that would allow a large, stable airflow range. Exhaust-nozzle, secondary-airflow pumping was used as the exit control for the stability bypass airflow. Propulsion system response and stability bypass performance were obtained for several transient airflow disturbances, both internal and external. Internal airflow disturbances included reductions in overboard bypass airflow, power lever angle, and primary-nozzle area, as well as compressor stall. Nozzle secondary pumping as a stability bypass exit control can provide the inlet with a large stability margin with no adverse effects on propulsion system performance.

Sanders, B. W.↗

Investigation of numerical properties of Hovenier's exit function equation for multiple scattering of light

A technique of deriving Hovenier's exit function equation (1978) for multiple scattering, starting with a set of invariant imbedding equations, is presented. The feasibility of the exit function equation as a means to obtain reflection and transmission functions is investigated for isotropic, Rayleigh, and Henyey-Greenstein phase functions with emphasis on the numerical stability, accuracy and timing. It is possible to compute the reflection function rather accurately with an efficiency comparable to that of the standard doubling technique for the same phase functions with moderate anisotropy. The resulting transmission is slightly less accurate than the reflection function, but it may be acceptable for practical purposes.

Kawabata, K.↗

Study of cooling air inlet and exit geometries for horizontally opposed piston aircraft engines

A semispan wing and nacelle of a typical general aviation twin-engine aircraft was tested to evaluate the cooling capability and drag of several nacelle shapes; the nacelle shapes included cooling air inlet and exit variations. The tests were conducted in the Ames Research Center's 40- by 80-Foot Wind Tunnel. It was found that the cooling air inlet geometry of opposed piston engine installations has a major effect on inlet pressure recovery, but only a minor effect on drag. Exit location showed a large effect on drag, especially for those locations on the sides of the nacelle where the suction characteristics were based on interaction with the wing surface pressures.

Katz, J.↗

Design, durability and low cost processing technology for composite fan exit guide vanes

A program was conducted to design, fabricate and test a durable, low cost, lightweight composite fan exit guide vane for high bypass ratio gas turbine engine application. Eight candidate material/design combinations were evaluated by NASTRAN finite element analysis. Four of these candidate systems were selected for composite vane fabrication by two vendors. A core and shell vane design was chosen in which the unidirectional graphite core fiber was the same for all candidates. The shell material, fiber orientation and ply configuration were varied. Material tests were performed on raw material and composite specimens to establish specification requirements. Composite vanes were nondestructively inspected and subsequently fatigue tested in both dry and 'wet' conditions. The program provided relevant data with respect to design analysis, materials properties, inspection standards, improved durability, weight benefits and part price of the composite fan exit guide vane.

Blecherman, S. S.↗

Turbulence characteristics in the annulus-wall boundary layer and wake mixing region of a compressor rotor exit

The flow at the exit of a turbomachinery rotor near the annulus wall is three-dimensional with a varying degree of turbulence and nonisotropic characteristics. The characteristics of the turbulence vary considerably with radial and axial location, blade loading, Reynolds number, free-stream turbulence, and the rotor blade geometry. This paper is concerned with the turbulence properties near the annulus wall region of a moderately loaded compressor blade. The variation of the streamwise, normal, and radial intensities as well as the stresses across the wake, its profile and decay characteristics, were determined with a tri-axial hot-wire probe in the stationary frame of reference. The turbulence characteristics in the annulus-wall region of the rotor exit were found to be highly complex due to the interaction of the blade wake and the annulus wall.

Davino, R.↗

Numerical simulations of a transverse indirect circulation and low-level jet in the exit region of an upper-level jet

A numerical study was performed of a severe weather event (tornado) which occurred on May 10, 1973 in the Ohio region. The situation was modeled with a primitive equation mesoscale dynamic formulation. Account was taken of precipitation, the planetary boundary layer parameters as bulk quantities, the vertical pressure gradient, and lateral boundary conditions based on radiosonde data. Two 12-hr simulations, adiabatic and nondivergent, respectively, were analyzed for relationships between upper and lower level jets. In the adiabatic formulation, a transverse circulation with a low level jet formed at the exit region of the upper level jet. The nondivergent situation led to similar, but weaker, phenomena. Both forms suggest that indirect circulation in the exit zone of an upper level jet is strongly influenced by the initial structure of the jet.

Brill, K. F.↗

Static investigation of post-exit vanes for multiaxis thrust vectoring

Transonic wind tunnel tests are conducted to determine the flow-turning capabilities and nozzle internal performance of axisymmetric and nonaxisymmetric nozzles employing postexit vanes for multiaxis thrust-vectoring. The geometric parameters investigated for the axisymmetric nozzle installation were number of vanes, vane curvature, vane location relative to nozzle exit, and vane deflection angle; for the nonaxisymmetric cases, the parameters were vane planform and curvature, nozzle type, and nozzle exit aspect ratio. Nozzle pressure ratio was varied from 1.5 to 6.0, using high pressure air.

Berrier, Bobby L.↗

Entrance and exit region friction factor models for annular seal analysis

The Mach number definition and boundary conditions in Nelson's nominally-centered, annular gas seal analysis are revised. A method is described for determining the wall shear stress characteristics of an annular gas seal experimentally. Two friction factor models are developed for annular seal analysis; one model is based on flat-plate flow theory; the other uses empirical entrance and exit region friction factors. The friction factor predictions of the models are compared to experimental results. Each friction model is used in an annular gas seal analysis. The seal characteristics predicted by the two seal analyses are compared to experimental results and to the predictions of Nelson's analysis. The comparisons are for smooth-rotor seals with smooth and honeycomb stators. The comparisons show that the analysis which uses empirical entrance and exit region shear stress models predicts the static and stability characteristics of annular gas seals better than the other analyses. The analyses predict direct stiffness poorly.

Elrod, David Alan↗

The effects of initial jet exit conditions on plume resonance

The acoustic emission and boundary layer of a cold jet issuing from an underexpanded sonic nozzle have been measured for lip thicknesses of the nozzle exit varying from 0.015-0.625 nozzle diameters. Near-field acoustic data demonstrate that the amplitude and frequency of certain modes of screech and the dominant mode of instability which exists in the shear layer are dependent on nozzle lip thickness. Changes in momentum thickness due to variations in the nozzle exit were also quantified.

Ponton, Michael K.↗

Anisotropy of thermal infrared exitance in sunflower canopies

Anisotropy of thermal infrared exitance above and within a relatively closed fully irrigated sunflower canopy is detailed. Azimuthal variation in thermal infrared exitance above canopies was weakly (statistically) related to solar position and was comparable to or larger than errors in satellite-based canopy estimates. Anisotropy within canopies was significantly lower and decreased with canopy closure and depth into the canopy. Measured azimuthal isotropy within canopies supports the use of this assumption in radiative transfer models. Significant differences in canopy temperature measurements were found depending upon whether the instruments were within or above the canopy. These differences could produce errors of 20-35 percent in latent energy estimates during periods of high evapotranspiration (ET) and greater errors in periods of restricted ET.

Tha Paw u, Kyaw↗

Bias and uncertainty in the absorption emission measurement of atomic sodium density in the SSME exit plane

The measurement of atomic sodium concentration in the TTB 019 firing of April 1990 is significant in that it represents the first measurement of density at the exit plane of the space shuttle main engine. The knowledge of the sodium density, combined with the certainty that the exit plane of the plume is optically thin at the sodium D-line wavelengths, provides essential information for evaluation of diagnostic techniques using sodium atoms, such as resonant Doppler velocimetry for temperature, pressure, and velocity through high resolution fluorescent lineshape analysis. The technique used for the sodium atom line transmission (SALT) measurements is that of resonant absorption emission using a hollow cathode lamp as the reference source. Through the use of two-dimensional kinetic (TDK) predictions of temperature and density for the flight engine case and radiative transfer calculations, this line-of-sight spectrally integrated transmission indicates a sodium atom concentration, i.e., mole fraction, of 0.91e-10. The subject of this paper is the assumptions and measurement uncertainties tied into the calculation. Because of the narrow shape of the source emission, the uncertainties in the absorption profile could introduce considerable bias in the measurement. The following were investigated: (1) the inclusion of hyperfine splitting of the D-lines in the calculation; (2) the use of the flight engine predictions of plume temperature and density versus those for the large throat engine; (3) the assumption of a Gaussian, i.e., Doppler, distribution for the source radiance with a temperature of 400 K; (4) the use of atomic collisional shift and width values for the work by Jongerius; and (5) a Doppler shift for a 7 degree outward velocity vector at the plume edge. Also included in the study was the bias introduced by an uncertainty in the measurement of the D1/D2 line ratio in the source.

Bauman, Leslie E.↗

Static thrust-vectoring performance of nonaxisymmetric convergent-divergent nozzles with post-exit yaw vanes

A static (wind-off) test was conducted in the Static Test Facility of the 16-ft transonic tunnel to determine the performance and turning effectiveness of post-exit yaw vanes installed on two-dimensional convergent-divergent nozzles. One nozzle design that was previously tested was used as a baseline, simulating dry power and afterburning power nozzles at both 0 and 20 degree pitch vectoring conditions. Vanes were installed on these four nozzle configurations to study the effects of vane deflection angle, longitudinal and lateral location, size, and camber. All vanes were hinged at the nozzle sidewall exit, and in addition, some were also hinged at the vane quarter chord (double-hinged). The vane concepts tested generally produced yaw thrust vectoring angles much less than the geometric vane angles, for (up to 8 percent) resultant thrust losses. When the nozzles were pitch vectored, yawing effectiveness decreased as the vanes were moved downstream. Thrust penalties and yawing effectiveness both decreased rapidly as the vanes were moved outboard (laterally). Vane length and height changes increased yawing effectiveness and thrust ratio losses, while using vane camber, and double-hinged vanes increased resultant yaw angles by 50 to 100 percent.

Foley, Robert J.↗

Pulsed laser Rayleigh scattering diagnostic for hydrogen/oxygen rocket exit plane flowfield velocimetry

A Doppler-resolved, pulsed laser Rayleigh scattering diagnostic has been developed to obtain local flowfield velocity measurements at the exit plane of a low thrust hydrogen/oxygen rocket engine operating in a high-altitude test facility. Fiberoptic signal collection was employed to obtain the forescatter and backscatter Doppler shifts necessary to resolve the axial and radial velocity components. A radial profile was obtained by traversing the collection probes along the beam path at the nozzle exit. The results are compared with theoretical predictions from a full Navier-Stokes model (RK/RPLUS). Significant discrepancies between the measured and predicted axial velocity profiles are observed, in terms of both magnitude and character. Radial velocity measurements exhibit excellent agreement with predictions near the centerline but show some departure off-axis. The discrepancies between theory and experiment are potentially the result of enhanced mixing between the core and fuel-film region beyond that predicted, and/or flow stratification between the hydrogen and oxygen injected into the central core region.

Zupanc, Frank J.↗

Plasma arc welding torch having means for vortexing plasma gas exiting the welding torch

A plasma arc welding torch is described wherein a plasma gas is directed through the body of the welding torch and out of the body across the tip of the welding electrode disposed at the forward end of the body. The plasma gas is provided with a vortexing motion prior to exiting the body by a vortex motion imparting member which is mounted in an orifice housing member and carried in the forward portion of the torch body. The orifice housing member is provided with an orifice of an predetermined diameter through which the electric arc and the plasma gas exits.

Rybicki, Daniel J.↗