Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electrodeposition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Solar absorption characteristics of several coatings and surface finishes

Solar absorption characteristics are established for several films potentially favorable for use as receiving surfaces in solar energy collectors. Included in the investigation were chemically produced black films, black electrodeposits, and anodized coatings. It was found that black nickel exhibited the best combination of selective optical properties of any of the coatings studied. A serious drawback to black nickel was its high susceptibility to degradation in the presence of high moisture environments. Electroplated black chrome generally exhibited high solar absorptivities, but the emissivity varied considerably and was also relatively high under some conditions. The black chrome had the greatest moisture resistance of any of the coatings tested. Black oxide coatings on copper and steel substrates showed the best combination of selective optical properties of any of the chemical conversion films studied.

Lowery, J. R.↗
NASA NTRS1977

Estimating surface temperature in forced convection nucleate boiling: A simplified method

During a test program to investigate low-cycle thermal fatigue, 21 of 22 cylindrical test sections of a cylindrical rocket thrust chamber were thermally cycled to failure. Cylinder liners were fabricated from OFHC copper, Amzirc, and NARloy-Z. The cylinders were fabricated by milling cooling channels into the liner and closing out the backside with electrodeposited copper. The tests were conducted at a chamber pressure of 4.14 MN/sq m (600 psia) and an oxidant-fuel ratio of 6.0 using hydrogen-oxygen as propellants. The average throat heat flux was 54 MW/sq m (33 Btu/sq in./sec). All of the failures were characterized by a thinning of the cooling channel wall and eventual failure by tensile rupture. The 1/2-hard Amzirc material showed little improvement in cyclic life when compared with OFHC copper; while the NARloy-Z and aged Amzirc materials had the best cyclic life characteristics. One OFHC copper cylinder was thermall cycled 2044 times at a steady-state hot-gas-side wall temperature of 514 K (925 R) without failing.

Hendricks, R. C.↗
NASA NTRS1977

Status of the Electroforming Shield Design (ESD) project

The utilization of a digital computer to augment electrodeposition/electroforming processes in which nonconducting shielding controls local cathodic current distribution is reported. The primary underlying philosophy of the physics of electrodeposition was presented. The technical approach taken to analytically simulate electrolytic tank variables was also included. A FORTRAN computer program has been developed and implemented. The program utilized finite element techniques and electrostatic theory to simulate electropotential fields and ionic transport.

Fletcher, R. E.↗
NASA NTRS1977

Improved catalysts by low-G processing

The advantages of space for manufacturing more perfect microcrystalline morphologies and structures will be investigated. Production of smaller silver and palladium crystals with enhanced catalytic properties is discussed. The elimination of convection accompanying electrodeposition of fine metallic powders at high overvoltages in a low gravity environment is outlined.

Grodzka, P. G.↗
NASA NTRS1977

Diffraction grating transmission efficiencies for XUV and soft X rays

The manufacture and properties of a grating intended for extrasolar X-ray studies are described. The manufacturing process uses a split laser beam exposing an interference pattern on the photoresist-coated glass plated with a nickel parting layer. The grating, supporting structure, and mounting frame are electrodeposited on the nickel parting layer, and the final product is lifted from the glass substrate by selective etching of the nickel. A model was derived which relates the number of counts received in a given order m as a function of photon wavenumber. A 4-deg beam line was used to measure the efficiencies of gold transmission gratings for diffraction of X-rays in the range of 45 to 275 eV. The experimental results are in good agreement with model calculations.

Schnopper, H. W.↗
NASA NTRS1979

Electroplated "cold patch" for critical parts

Cracks in metal parts are filled by electrodeposition in plating tank that conforms to part to be repaired. Principle is applicable to repair of cracks in components of chemical reactors and other critical structures.

Tripp, H. A.↗
NASA NTRS1977

High-temperature ductility of electro-deposited nickel

Work done during the past several months on high temperature ductility of electrodeposited nickel is summarized. Data are presented which show that earlier measurements made at NASA-Langley erred on the low side, that strain rate has a marked influence on high temperature ductility, and that codeposition of a small amount of manganese helps to improve high temperature ductility. Influences of a number of other factors on nickel properties were also investigated. They included plating solution temperature, current density, agitation, and elimination of the wetting agent from the plating solution. Repair of a large nozzle section by nickel plating is described.

Dini, J. W.↗
NASA NTRS1978

Investigation of the effect of ceramic coatings on rocket thrust chamber life

Cylindrical rocket thrust chamber cylinders were coated with a 0.203 mm (0.008 in.) layer of zirconium oxide using a process that employed electrodeposition of metal to a spray coated mandrel. The cylinders were cyclically tested using hydrogen oxygen propellants at a nominal chamber pressure of 4.14 MN/sq m (600 psia) to show the effect of the coating on life. Both cylinders failed prematurely due to causes unrelated to the coatings. Post destructive analysis showed no cooling passage wall deformation. Where erosion of the coating occurred, the coating thickness stabilized at 0.061 mm (0.0024 in.) within 80 cycles and remained well adhered throughout the tests.

Quentmeyer, R. J.↗
NASA NTRS1978

Investigation of the effect of ceramic coatings on rocket thrust chamber life

Two cylindrical rocket thrust chamber cylinders were coated with a 0.203 mm layer of zirconium oxide using a process that employed electrodeposition of metal to a spray-coated mandrel. The cylinders were cyclically tested using hydrogen-oxygen propellants at a nominal chamber pressure of 4.14 MN/sq m to show the effect of the coating on life. Both cylinders failed prematurely due to causes unrelated to the coatings. Post destructive analysis showed no cooling passage wall deformation. Where erosion of the coating occurred, the coating thickness stabilized at 0.061 mm within 80 cycles and remained well adhered throughout the tests. The hot-gas-side metal wall temperature and the theoretical maximum effective strain were reduced by 80 and 92%, respectively, where the coating was 0.203 mm thick and by 40 and 50%, respectively, where the coating was 0.061 mm thick compared to an uncoated cylinder. The 50 and 92% reductions in maximum effective strain resulted in theoretical lives of 1900 cycles and greater than 10,000 cycles, respectively, compared to 300 cycles for the uncoated cylinder.

Quentmeyer, R. J.↗
NASA NTRS1970

Electroplating offers embrittlement protection

Thin copper electrodeposited layer protects metal parts in environments with which they may be incompatible. Originally developed for main engine of Space Shuttle where high strength nickle alloy bellows must operate in high-pressure hydrogen, technique protects nickel and is unaffected by forming process or subsequent heat treatment and preinstallation processing.

Daniels, C. M., Jr.↗
NASA NTRS1980

Selective optical coatings for solar collectors

For best performance, energy-absorbing surface of solar collector should be characterized by high ratio of solar absorptance to thermal emitance. Report on optical characteristics of several chemical treatments and electrodeposited coatings for metal solar-absorbing surfaces should interest designers and users of solar-energy systems. Moisture resistance of some coatings is also reported.

Lowery, J. R.↗
NASA NTRS1982

Electrochemical Assay of Gold-Plating Solutions

Gold content of plating solution is assayed by simple method that required only ordinary electrochemical laboratory equipment and materials. Technique involves electrodeposition of gold from solution onto electrode, the weight gain of which is measured. Suitable fast assay methods are economically and practically necessary in electronics and decorative-plating industries. If gold content in plating bath is too low, poor plating may result, with consequent economic loss to user.

Chiodo, R.↗
NASA NTRS1981

The Structure and Properties of Diffusion Assisted Bonded Joints in 17-4 PH, Type 347, 15-5 PH and Nitronic 40 Stainless Steels

Diffusion assisted bonds are formed in 17-4 PH, 15-5 PH, type 347 and Nitronic 40 stainless steels using electrodeposited copper as the bonding agent. The bonds are analyzed by conventional metallographic, electron microprobe analysis, and scanning electron microscopic techniques as well as Charpy V-notch impact tests at temperatures of 77 and 300 K. Results are discussed in terms of a postulated model for the bonding process.

Wigley, D. A.↗
NASA NTRS1980

Optical measurements and tests performed in a low-gravity environment

Shadowgraph and schlieren techniques have been used on board the NASA KC-135 low-gravity simulation aircraft to measure gravity-related fluid flow occurring in various experimental configurations. These configurations included cooled and solidified ammonium chloride and water, electrodeposited cobalt in CoSO4 solution, and immiscible and crystal melt solutions. Hardware tests have also been performed for such critical optical system components as lasers and spatial filters to determine their performance and operation under low-gravity conditions. These test results will be used in the design of the various future Shuttle experiments which will utilize advanced optical measurement techniques. The design and configuration of the optical systems used to make these measurements and tests are presented, and the performance and operation of these systems and their components under low-gravity conditions are discussed. Some preliminary results are included.

Owen, R. B.↗
NASA NTRS1982

Plating To Reinforce Welded Joints

Electrodeposition used to strengthen welded joints gouged, nicked, or suffered other mechanical damage. Plating cell, typically of acrylic plastic such as poly (Methylmetacrylate), is assembled around part to be plated. Areas not to be plated are masked with plater's tape. Weld area is plated in standard nickel-plating process.

Otousa, J. E.↗
NASA NTRS1981

Mechanism and models for zinc metal morphology in alkaline media

Based on experimental observations, a mechanism is presented to explain existence of the different morphologies of electrodeposited zinc in alkaline solution. The high current density dendrites appear to be due to more rapid growth on the nonbasal crystallographic planes than on the basal plane. The low current density moss apparently results from dissolution from the nonbasal planes at low cathodic voltages. Electrochemical models were sought which would produce such a phenomenon. The fundamental plating mechanism alone accounts only for different rates on different planes, not for zinc dissolution from a plane in the cathodic region. Fourteen models were explored; two models were in accord with the proposed mechanism. One involves rapid disproportionation of the zinc +1 species on the nonbasal planes. The other involves a redox reaction (corrosion) between the zinc-zincate and hydrogen-water systems.

May, C. E.↗
NASA NTRS1982

Interferometry and holography in a low-gravity environment

The groundwork for the use of advanced optical measurement techniques in Space Shuttle materials processing in space (MPS) experiments is being laid in tests, conducted aboard a NASA KC-135 aircraft flying a parabolic trajectory, involving a Mach-Zehnder interferometer and a sideband holographic unit. The two experiments described are (1) the observation of flow during solidification, in which fluid concentration and temperature profiles were measured during unidirectional solidification of a saturated NH4Cl-H2O solution, and (2) the observation of electrodeposition flow, in which interferometry is used to provide quantitative data required in the understanding of electrochemical process transport properties. The free-floating holographic unit was operated in the microgravity environment to both test the practicality of optical systems in such conditions and test the shock and vibration characteristics of the package.

Owen, R. B.↗
NASA NTRS1981

Electrorefining process for lunar free metal - Space and terrestrial applications and implications

An electrochemical refining process is proposed for the separation and recovery of principal and trace elements from reduced metallic particles found in lunar soils. A process variation is presented for purification and recovery of chromium and manganese from electrodeposited impure iron available from lunar silicate and other minerals. The process involves anodic dissolution of impure metal and cathodic deposition in divided cells using aqueous chloride solutions. The anolyte is withdrawn and separated using ion exchange techniques.

Waldron, R. D.↗