Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLAME PROPAGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

OH production by transient plasma and mechanism of flame ignition and propagation in quiescent methane-air mixtures

Transient plasma induced production of OH is followed in a quiescent, stoichiometric CH{sub 4}-air mixture using the planar laser induced fluorescence technique. Ignition and subsequent flame propagation, for both the transient plasma and traditional spark ignition, are observed with a high speed camera (2000 fps). The transient plasma is generated using a 70 ns FWHM, 60 kV, 800 mJ pulse. OH production was confirmed throughout the chamber volume; however, the mean number density was found to decay below 1.3 x 10{sup 14}cm{sup -3} near 100 {mu}s. Nonetheless, ignition induced by transient plasma was decidedly faster than by spark ignition. Using the high speed camera, ignition initiated by transient plasma was found to occur along the length of the anode at approximately 1 ms, leading to the formation of a wrinkled, cylindrically-shaped flame. Analysis of the flame front propagation rates shows that flames ignited by transient plasma propagate essentially at the speed consistent with well accepted literature values for the stoichiometric methane-air mixture. This supports the notion that residue plasma, if any, has little effect on flame propagation. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Experimental study on tribrachial flames in narrow channels with small fuel concentration gradients

Edge flames have become a subject of interest as basic structures for lifted-flame stabilization and turbulent flame propagation. Recently, with the development of small diffusion flame devices as energy sources for various small mechanical systems, edge flames within narrow spaces have also been investigated. In this study, the structures and propagation characteristics of a tribrachial flame (or an edge flame) in a confined narrow channel, with very small fuel concentration gradients, were experimentally investigated. Tribrachial flames could be successfully stabilized in the narrow channels. The flame shapes and propagation velocities were compared by changing the four experimental parameters of the mean velocity, fuel concentration gradient, channel gap, and fuel dilution ratio. It was experimentally observed that the luminosity of the diffusion branch diminished when the channel gap decreased. It was also found that there is a critical condition in the channel gap for maximum propagation velocity. A flow redirection effect and a heat loss effect are thought to have played a key role in the variation of the PVTF in a narrow channel, and their competition with each other caused a peak value of the PVTF at the critical channel gap. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Large Eddy Simulation Modeling of Flashback and Flame Stabilization in Hydrogen-Rich Gas Turbines Using a Hierarchical Validation Approach

This project was a combined computational and experimental effort to improve predictive capability for boundary layer flashback of premixed swirl flames relevant to gas-turbine power plants operating with high-hydrogen-content fuels. During the course of this project, significant progress in modeling was made on four major fronts: 1) use of direct numerical simulation of turbulent flames to understand the coupling between the flame and the turbulent boundary layer; 2) improved modeling capability for flame propagation in stratified pre-mixtures; 3) improved portability of computer codes using the OpenFOAM platform to facilitate transfer to industry and other researchers; and 4) application of LES to flashback in swirl combustors, and a detailed assessment of its capabilities and limitations for predictive purposes. A major component of the project was an experimental program that focused on developing a rich experimental database of boundary layer flashback in swirl flames. Both methane and high-hydrogen fuels, including effects of elevated pressure (1 to 5 atm), were explored. For this project, a new model swirl combustor was developed. Kilohertz-rate stereoscopic PIV and chemiluminescence imaging were used to investigate the flame propagation dynamics. In addition to the planar measurements, a technique capable of detecting the instantaneous, time-resolved 3D flame front topography was developed and applied successfully to investigate the flow-flame interaction. The UT measurements and legacy data were used in a hierarchical validation approach where flows with increasingly complex physics were used for validation. First component models were validated with DNS and literature data in simplified configurations, and this was followed by validation with the UT 1-atm flashback cases, and then the UT high-pressure flashback cases. The new models and portable code represent a major improvement over what was available before this project was initiated.

42 ENGINEERING↗

Effect of NO on extinction and re-ignition of vortex-perturbed hydrogen flames

The catalytic effect of nitric oxide (NO) on the dynamics of extinction and re-ignition of a vortex-perturbed non-premixed hydrogen-air flame is studied in a counterflow burner. A diffusion flame is established with counterflowing streams of nitrogen-diluted hydrogen at ambient temperature and air heated to a range of temperatures that brackets the auto-ignition temperature. Localized extinction is induced by impulsively driving a fuel-side toroidal vortex into the steady flame, and the recovery of the extinguished region is monitored by planar laser-induced fluorescence (PLIF) of the hydroxyl radical (OH). The dynamics of flame recovery depend on the air temperature and fuel concentration, and four different recovery modes are identified. These modes involve combinations of edge-flame propagation and the expansion of an auto-ignition kernel that forms within the extinguished region. The addition of a small amount of NO significantly alters the re-ignition process by shifting the balance between chain-termination and chain-propagation reactions to enhance auto-ignition. The ignition enhancement by this catalytic effect causes a shift in the conditions that govern the recovery modes. In addition, the effects of NO concentration and vortex strength on the flame recovery are examined. Direct numerical simulations of the flame-vortex interaction with and without NO doping show how the small amount of OH produced by NO-catalyzed reactions has a significant impact on the development of an auto-ignition kernel. This joint experimental and numerical study provides detailed insight into the interaction between transient flows and ignition processes. (author)

08 HYDROGEN↗

Assessment of impinged flame structure in high-pressure direct diesel injection

Spray impingement often occurs during cold-start in direct-injection diesel engines, affecting the subsequent combustion process by altering the local flow condition. This work has investigated the impinged flame structure by examining local expansion distance and planar curvature of the boundary in details. The experiments were carried out in a constant volume combustion chamber. The injection pressure and ambient density were varied from 120 to 180 MPa and 14.8 to 30.0 kg/m 3 under non-vaporizing conditions, respectively. For reacting conditions, the injection pressure and ambient density were fixed at 150 MPa and 22.8 kg/m 3 but with different ambient temperatures from 800 to 1000 K. Unlike orthogonal spray impingement, the profile of expansion distance along the radial direction at the 60° impinging angle is non-uniform but the profile is comparable between the non-vaporizing and reacting conditions under the same injection pressure and ambient density. With the help of Intensity-aXial-Time method, the most intensive soot luminosity region and Mie scattering intensity region are identified and the region has been found to be along the impinged spray axial direction. Outmost boundary of an impinged flame is found to have wrinkles attributed to air entrainment. The temporal level of flame wrinkles is higher in reacting conditions than in non-vaporizing conditions. The scatter distribution of the boundary curvature and near-field soot formation illustrates an inverted “S” shape correlation with time. High flame luminosity is found to be formed in concave regions while less soot is formed in convex regions. This inverted S-shape is a new finding of the state relationship at the solid–liquid–gas impinged flame propagation. Finally, heat flux measurement through the plate is examined.

Engineering↗

Direct numerical simulation of flame stabilization assisted by autoignition in a reheat gas turbine combustor

A three-dimensional direct numerical simulation (DNS) is performed for a turbulent hydrogen-air flame, represented with detailed chemistry, stabilized in a model gas-turbine combustor. The combustor geometry consists of a mixing duct followed by a sudden expansion and a combustion chamber, which represents a geometrically simplified version of Ansaldo Energia’s GT26/GT36 sequential combustor design. In this configuration, a very lean blend of hydrogen and vitiated air is prepared in the mixing duct and convected into the combustion chamber, where the residence time from the inlet of the mixing duct to the combustion chamber is designed to coincide with the ignition delay time of the mixture. The results show that when the flame is stabilized at its design position, combustion occurs due to both autoignition and flame propagation (deflagration) modes at different locations within the combustion chamber. A chemical explosive mode analysis (CEMA) reveals that most of the fuel is consumed due to autoignition in the bulk-flow along the centerline of the combustor, and lower amounts of fuel are consumed by flame propagation near the corners of the sudden expansion, where the unburnt temperature is reduced by the thermal wall boundary layers. An unstable operating condition is also identified, wherein periodic auto-ignition events occur within the mixing duct. These events appear upstream of the intended stabilization position, due to positive temperature fluctuations induced by pressure waves originating from within the combustion chamber. This DNS investigation represents the initial step of a comprehensive research effort aimed at gaining detailed physical insight into the rate-limiting processes that govern the sequential combustor behavior and avoid the insurgence of the off-design auto-ignition events.

20 FOSSIL-FUELED POWER PLANTS↗

Numerical study of the ignition behavior of a post-discharge kernel in a turbulent stratified crossflow

Ensuring robust ignition is critical for the operability of aeronautical gas-turbine combustors. For ignition to be successful, an important aspect is the ability of the hot gas generated by the spark discharge to initiate combustion reactions, leading to the formation of a self-sustained ignition kernel. This study focuses on this phenomena by performing simulations of kernel ignition in a crossflow configuration that was characterized experimentally. First, inert simulations are performed to identify numerical parameters correctly reproducing the kernel ejection from the ignition cavity, which is here modeled as a pulsed jet. In particular, the kernel diameter and the transit time of the kernel to the reacting mixture are matched with measurements. Considering stochastic perturbations of the ejection velocity of the ignition kernel, the variability of the kernel transit time is also reproduced by the simulations. Subsequently, simulations of a series of ignition sequences are performed with varying equivalence ratio of the fuel-air mixture in the crossflow. The numerical results are shown to reproduce the ignition failure that occurs for the leanest equivalence ratio ($φ = 0.6$). For higher equivalence ratios, the simulations are shown to capture the sensitivity of the ignition to the equivalence ratio, and the kernel successfully transitions into a propagating flame. Significant stochastic dispersion of the ignition strength is observed, which relates to the variability of the transit time of the kernel to the re- active mixture. An analysis of the structure of the ignition kernel also highlights the transition towards a self-propagating flame for successful ignition conditions.

42 ENGINEERING↗

Invited Review. Combustion instability in spray-guided stratified-charge engines. A review

Our article reviews systematic research on combustion instabilities (principally rare, random misfires and partial burns) in spray-guided stratified-charge (SGSC) engines operated at part load with highly stratified fuel -air -residual mixtures. Results from high-speed optical imaging diagnostics and numerical simulation provide a conceptual framework and quantify the sensitivity of ignition and flame propagation to strong, cyclically varying temporal and spatial gradients in the flow field and in the fuel -air -residual distribution. For SGSC engines using multi-hole injectors, spark stretching and locally rich ignition are beneficial. Moreover, combustion instability is dominated by convective flow fluctuations that impede motion of the spark or flame kernel toward the bulk of the fuel, coupled with low flame speeds due to locally lean mixtures surrounding the kernel. In SGSC engines using outwardly opening piezo-electric injectors, ignition and early flame growth are strongly influenced by the spray's characteristic recirculation vortex. For both injection systems, the spray and the intake/compression-generated flow field influence each other. Factors underlying the benefits of multi-pulse injection are identified. Finally, some unresolved questions include (1) the extent to which piezo-SGSC misfires are caused by failure to form a flame kernel rather than by flame-kernel extinction (as in multi-hole SGSC engines); (2) the relative contributions of partially premixed flame propagation and mixing-controlled combustion under the exceptionally late-injection conditions that permit SGSC operation on E85-like fuels with very low NO x and soot emissions; and (3) the effects of flow-field variability on later combustion, where fuel-air-residual mixing within the piston bowl becomes important.

42 ENGINEERING↗

Experimental annular stratified flames characterisation stabilised by weak swirl

A burner for the investigation of lean stratified premixed flames propagating in intense isotropic turbulence has been developed. Lean pre-mixtures of methane at different equivalence ratios were divided between two concentric co-flows to obtain annular stratification. Turbulence generators were used to control the level of turbulence intensity in the oncoming flow. A third annular weakly swirling airflow provided the flame stabilisation mechanism. A fundamental characteristic was that flame stabilisation did not rely on flow recirculation. The flames were maintained at a position where the local mass flux balanced the burning rate, resulting in a freely propagating turbulent flame front. The absence of physical surfaces in the vicinity of the flame provided free access for laser diagnostics. Stereoscopic Planar Image Velocimetry (SPIV) was applied to obtain the three components of the instantaneous velocity vectors on a vertical plane above the burner at the point of flame stabilisation. The instantaneous temperature fields were determined through Laser Induced Rayleigh (LIRay) scattering. Planar Laser Induced Fluorescence (PLIF) of acetone was used to calculate the average equivalence ratio distributions. Instantaneous turbulent burning velocities were extracted from SPIV results, while flame curvature and flame thermal thickness were calculated using the instantaneous temperature fields. The PDFs of these quantities were analysed to consider the separate influence of equivalence ratio stratification and turbulence. Increased levels of turbulence resulted in the expected higher turbulent burning velocities and flame front wrinkling. Flames characterised by higher fuel gradients showed higher turbulent burning velocities. Increased fuel concentration gradients gave rise to increased flame wrinkling, particularly when associated with positive small radius of curvature. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Application and refinement of scaling analyses for mild ignition

Thermal and compositional inhomogeneities may significantly affect outcomes in a variety of fundamental and practical systems, including shock tubes, rapid compression machines, and combustion engines. Even in idealized configurations, homogenous reactive mixtures can never be completely uniform. This can lead to premature ignition, undesired flame propagation, or even detonation. Such perturbations to reacting flows have been recently analyzed by the authors of this work using a novel scaling analysis. That analysis identified three competing processes that affect the influence of an inhomogeneity on the globally observed ignition. First, diffusive quenching of a locally perturbed hot-spot can compete with premature ignition of this reaction center. Next, the ignited flame may extinguish due to high stretch rate. Finally, compressive heating of the end-gas due to flame propagation can compete with homogeneous ignition of the unperturbed bulk gas. In the present work, this scaling analysis is applied to ignition delay measurements reported in the literature. In these experiments, ignition often occurs earlier than expected due to inhomogeneities in the mixture. The previously-developed framework is utilized to infer a representative hot-spot geometry which could lead to the observed early ignition, demonstrating the validity of the scaling analysis.

mild ignition↗

Ignition, Flame Progation, and End-Gas Autoignition Studies of Natural Gas/ EGR Blends in a Rapid Compression Machine

The development of high efficiency, spark ignited natural gas engines is currently limited by engine knock at high power density (at high compression ratio and/or elevated boost pressures) and misfire (at lean conditions and/or high exhaust gas recirculation levels). The knock and misfire limits are further confounded by the wide variety in fuel reactivity observed in “pipeline quality” natural gas. In this study, a rapid compression machine (RCM) was used to characterize the effects of variation in natural gas fuel reactivity and exhaust gas recirculation (EGR) on homogeneous ignition delay, flame propagation rate and end-gas autoignition (EGAI) propensity for stoichiometric natural gas/oxidizer/EGR blends. Pipeline quality natural gas with variable reactivity (68 < Methane Number < 95) was simulated using mixtures of methane, ethane, and propane. EGR was simulated with mixtures of Ar, CO2, CO, and NO. EGR substitution rates were varied from 0 to 30 mass percent. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures of 24.0 to 33.1 bar and compressed temperatures of 667 to 980 K. Flame propagation rate and EGAI propensity was measured at spark-ignition pressures of 29.9 to 32.9 bar and temperatures of 721 to 782 K.

Mohr, Jeffrey↗

Detection of low Temperature heat release (LTHR) in the standard Cooperative Fuel Research (CFR) engine in both SI and HCCI combustion modes

To this date, extensive research has been conducted to understand the low-temperature auto-ignition chemistry of gasoline. The detection of low-temperature chemical reactions under Spark Ignition (SI) combustion cannot be detected, as they are hidden by the flame propagation. Alternatively, Homogeneous Charge Compression Ignition (HCCI) combustion has a two-stage combustion involving low and high-temperature heat release (LTHR and HTHR respectively). Both Knocking SI and HCCI combustion involve auto-ignition and are governed by fuel characteristics and the pressure-temperature (P-T) history. Therefore, HCCI combustion might provide an alternative to understand the knocking behavior and LTHR in modern SI engines. A standard Cooperative Fuel Research (CFR) engine was operated at lean HCCI conditions (lambda 3), as well as SI conditions at stoichiometry. For SI combustion, the CFR engine was operated with RON-like conditions, but at late spark timing to induce LTHR prior to flame propagation. Three RON 90 binary fuel blends were investigated, being composed of n-heptane with isooctane, toluene, or ethanol. This work demonstrated that the CFR engine under stoichiometric SI with late spark timing and HCCI combustion mode can help to detect LTHR which is not possible in the standard RON test. The intake pressure and temperature sweeps showed similar effects on LTHR for both combustion modes. The linking of auto-ignition behavior of SI and HCCI was dependent primarily on intake valve closing (IVC) conditions. In conclusion, the high exhaust temperature in SI lead to high IVC temperatures. In order to match the IVC temperatures and to overlap the P-T trajectories, the intake temperature for HCCI was increased.

33 ADVANCED PROPULSION SYSTEMS↗

THE EFFECT OF FUEL REACTIVITY AND EXHAUST GAS RECIRCULATION ON KNOCK PROPENSITY OF NATURAL GAS

The development of high efficiency, spark ignited natural gas engines is currently limited by engine knock at high compression ratio/elevated boost pressures and misfire at lean conditions/high exhaust gas recirculation (EGR) levels. The knock and misfire limits are further confounded by the wide variety in fuel reactivity observed in “pipeline quality” natural gas. In this study, a rapid compression machine was used to characterize the effects of EGR and variation in natural gas fuel reactivity on the homogeneous ignition delay, flame propagation rate, and end- gas autoignition propensity for stoichiometric natural gas/oxidizer/EGR blends. A reduced chemical kinetic mechanism was also developed to accurately model the homogeneous ignition delays measured in the Colorado State University rapid compression machine (CSU RCM). Pipeline quality natural gas with a range of chemical reactivity (68 < Methane Number < 95) was simulated using mixtures of CH4, C2H6, and C3H8. Exhaust gas recirculation gases were simulated with mixtures of Ar, CO2, CO, and NO at substitution rates of 0 to 30 mass percent. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures of 30.2 to 34.0 bar and compressed temperatures of 667 to 980 K. End-gas autoignition fraction and flame propagation rate were measured by initiating a laser spark in the center of the combustion chamber, after compression, at pressures of 30.7 to 32.7 bar and temperatures of 751 to 795 K. The results indicate that both fuel reactivity and the presence of reactive species (NO and CO) in the exhaust gas recirculation have a strong impact on end-gas autoignition fraction. A chemical kinetic mechanism was developed to predict homogeneous ignition delays for pipeline quality natural gas in a pressure and temperature range of 1-100 bar and 500-1000 K respectively. This mechanism accurately predicted measured homogeneous ignition delay in the RCM with a total average relative error of 11.0%.

Mohr, Jeffrey↗

Direct numerical simulations of reacting flows with detailed chemistry using many-core/GPU acceleration

A new direct numerical simulation (DNS) code for multi-component gaseous reacting flows has been developed at KAUST, with the state-of-the-art programming model for next generation high performance computing platforms. The code, named KAUST Adaptive Reacting Flows Solver (KARFS), employs the MPI+X programming, and relies on Kokkos for “X” for performance portability to multi-core, many-core and GPUs, providing innovative software development while maintaining backward compatibility with established parallel models and legacy code. The capability and potential of KARFS to perform DNS of reacting flows with large, detailed reaction mechanisms is demonstrated with various model problems involving ignition and turbulent flame propagations with varying degrees of chemical complexities.

Computer Science↗

Sensitivity of He Flames in X-Ray Bursts to Nuclear Physics

Through the use of axisymmetric 2D hydrodynamic simulations, we further investigate laterally propagating flames in X-ray bursts (XRBs). Our aim is to understand the sensitivity of a propagating helium flame to different nuclear physics. Using the Castro simulation code, we confirm the phenomenon of enhanced energy generation shortly after a flame is established by adding 12 C(p, γ) 13 N(α, p) 16 O to the network, in agreement with the past literature. This sudden outburst of energy leads to a short accelerating phase, causing a drastic alteration in the overall dynamics of the flame in XRBs. Furthermore, we investigate the influence of different plasma screening routines on the propagation of the XRB flame. We finally examine the performance of simplified spectral deferred correction, a novel approach to hydrodynamics and reaction coupling incorporated in Castro, as an alternative to operator splitting.

79 ASTRONOMY AND ASTROPHYSICS↗

The role of collisional energy transfer in the thermal and prompt dissociation of 1-methyl allyl

Collisional energy transfer plays a pivotal role in a-priori calculations of the pressure-dependent rate constants obtained from a master equation. However, accurate determinations of collisional energy transfer parameters are rare and so most kinetic studies rely on best-fits of these parameters to experimental measurements (if available) or estimates guided from literature studies. In this work, we have quantified the effect of the uncertainty in energy transfer parameters on the thermal and prompt dissociation kinetics of a resonance stabilized radical, 1-methyl allyl (1MA), of relevance to the combustion of 1- and 2-butene isomers. Simulations using literature kinetics models were performed to assess the impact of these uncertainties on flame propagation and speciation data in laminar flames of 1- and 2-butene. Analyses of the uncertainty propagated by the energy transfer parameters for 1MA dissociation to the flame simulations, in particular the laminar flame speed, indicate an intricate coupling between the kinetics of 1MA dissociation (chain propagation) and its reaction with H-atoms (chain-termination). Ab-initio based theoretical calculations were also performed to obtain pressure-dependent kinetics for the reaction of 1MA with H-atoms. Lastly, theoretically calculated energy transfer parameters were used to best characterize the kinetics and branching between the chain propagating 1MA dissociation and the chain-terminating reaction 1MA + H.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Studies of premixed and non-premixed hydrogen flames

The hydrogen oxidation chemistry constitutes the foundation of the kinetics of all carbon- and hydrogen-containing fuels. The validation of rate constants of hydrogen-related reactions can be complicated by uncertainties associated with experimental data caused by the high reactivity and diffusivity of hydrogen.Here, accurate experimental data on flame propagation and extinction were determined for premixed and non-premixed hydrogen flames at pressures between p = 1 and 7 atm. The experiments were designed to sensitize the three-body H + O 2 + M → HO 2 + M reaction, whose rate is subject to notable uncertainty. This was achieved by increasing the pressure and by adding to the reactants H 2 O and CO 2 whose collision efficiencies are high compared to other species. In the present study, directly measured flame properties were compared against computed ones, in order to eliminate uncertainties associated with extrapolations, as is the case for laminar flame speeds. The measured extinction strain rates exhibit both a positive and negative dependence on pressure with and without weighting with the density, and this non-monotonic behavior is caused by the competition between the H + O 2 → O + OH and H + O 2 + M → HO 2 + M reactions as well as HO 2 kinetic pathways as pressure increases. The various kinetic models considered in this investigation did not reproduce equally well the non-premixed flame extinction data with added H 2 O. Yet, the predicted extinction strain rates were consistent between the various models in the case of added CO 2 . Finally, it was shown that the formulation of binary diffusion coefficient pairs including H–N 2 and H 2 –N 2 has a first order effect on the prediction of extinction strain rates of non-premixed H 2 flames.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗