Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW DEFLECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Flow measurements of an airfoil with deflected spoiler

Spoilers are used as an effective control surface in various stages of flight. The steady and unsteady flow characteristics change with incidence and spoiler angle. An experimental investigation is undertaken to understand the flow phenomena. Typical boundary layer and wake profiles at various incidences and spoiler angles are presented and discussed. A laminar separation is observed at low incidence and high spoiler angle. At incidence, a turbulent boundary layer develops and separation point moves downstream. Generally the wake profiles are asymmetric. When different length scales are used, the profiles become self-similar and symmetric. The importance of laser velocimetry in the reverse flow region is demonstrated by comparing the preliminary LDV measurements with the hot-wire results.

Lee, C. S.↗
NASA NTRS1957

A Method for Predicting Lift Increments Due to Flap Deflection at Low Angles of Attack in Incompressible Flow

A method is presented for estimating the lift due to flap deflection at low angles of attack in incompressible flow. In this method provision is made for the use of incremental section-lift data for estimating the effectiveness of high-lift flaps. The method is applicable to swept wings of any aspect ratio or taper ratio. The present method differs from other current methods mainly in its ease of application and its more general application. Also included is a simplified method of estimating the lift-curve slope throughout the subsonic speed range.

WINGS, COMPLETE - TAPER AND TWIST↗
NASA NTRS1993

Corrections to fringe distortion due to flow density gradients in optical interferometry

An analytical method is formulated to account for distortions of optical interferograms used for studies of flow over airfoils experiencing dynamic stall. It is shown that such distortions are generated primarily due to optical path deflections in the test flow, caused by large density gradients. Such in-flow optical path deflections are neglected in conventional optical techniques for flow studies. The present method employs a ray analysis to determine these in-flow optical path deflections, and accurately predicts the interferogram distortions.

Cho, Y. C.↗
NASA NTRS1987

Field line draping about fast coronal mass ejecta - A source of strong out-of-the-ecliptic interplanetary magnetic fields

Fast coronal mass ejecta interact strongly with the ambient interplanetary plasma and magnetic field into which they propagate. A shock forms in front of an ejection, and the slower moving ambient plasma ahead is accelerated and deflected from its path. It is argued that such flow accelerations and deflections of the ambient plasma must produce a draping of the ambient interplanetary magnetic field about the ejected material similar to that which occurs in the magnetosheath surrounding the earth's magnetosphere. The draping pattern should depend upon the overall size and shape of the ejection, its speed relative to the ambient plasma ahead, the orientation of the ambient magnetic field, and the position where the shocked plasma is sampled. At some locations upstream from an ejection draping leads to an enhancement of the out-of-the-ecliptic field component B(Z) at the expense of the ecliptic components. It is suggested that draping plays an important role in producing intervals of strong and prolonged negative B(Z) in the ecliptic plane at 1 AU, and thus may be an important factor in stimulating geomagnetic activity.

Gosling, J. T.↗
NASA NTRS1991

A finite element large deflection random response of a pipe containing fluid flow

A finite element approach is developed for beam type pipes undergoing large deflections subjected to random loadings. The influence of fluid velocity on the random response is investigated. The root-mean-square (rms) deflections and frequencies for different sound spectrum level values are determined for pipes with both ends either simply supported or clamped. The required number of modes to achieve accurate rms deflections is studied. The prediction of fatigue life is then based on the maximum rms stress. This analytical investigation will help to broaden the basic understanding of the role of fluid flow within structures subjected to random excitations.

Chiang, C. K.↗
NASA NTRS1980

High-frequency sound propagation in a spatially varying mean flow

An equation for acoustic ray paths in a spatially varying mean flow was examined to determine some of the characteristics of the flow gradient effects on sound propagation. In a potential flow, the acoustic rays are deflected in the direction of increasing mean flow, and the gradient of the mean flow speed is the dominant factor causing the ray deflection. In contrast, in a sheared mean flow, the vorticity is the dominant factor in deflection of the acoustic rays.

Cho, Y. C.↗
NASA NTRS1981

High-frequency sound propagation in a spatially varying mean flow

An equation for acoustic ray paths in a spatially varying mean flow has been examined to determine some of the characteristics of the flow gradient effects on sound propagation. In a potential flow the acoustic rays are deflected in the direction of increasing mean flow, and the gradient of the mean flow speed is the dominant factor causing the ray deflection. In contrast, in a sheared mean flow, the vorticity is the dominant factor in deflection of the acoustic rays.

Cho, Y. C.↗
NASA NTRS1993

Turbulence model evaluation for the prediction of flows over a supercritical airfoil with deflected aileron at high Reynolds number

Navier-Stokes solutions about a supercritical airfoil with aileron deflection have been computed using the CFL3D code coupled with the Baldwin-Lomax, Johnson-King, Baldwin-Barth, and Spalart-Allmaras turbulence models. Computations were made at a Mach number of 0.716 and chord Reynolds numbers of 5, 15, and 25 million. The airfoil was analyzed with both 0 deg and 2 deg (TED) aileron deflections. Comparisons over a range of angles-of-attack showed that solutions obtained using the Baldwin-Barth turbulence model presented the best agreement with experimental pressures and sectional lift coefficients. However, Reynolds number trends in sectional lift coefficient and in aileron effectiveness were not predicted consistently.

Londenberg, W. K.↗
NASA NTRS1999

Deflection of the local interstellar dust flow by solar radiation pressure

Interstellar dust grains intercepted by the dust detectors on the Ulysses and Galileo spacecrafts at heliocentric distances from 2 to 4 astronomical units show a deficit of grains with masses from 1 x 10(-17) to 3 x 10(-16) kilograms relative to grains intercepted outside 4 astronomical units. To divert grains out of the 2- to 4-astronomical unit region, the solar radiation pressure must be 1.4 to 1.8 times the force of solar gravity. These figures are consistent with the optical properties of spherical or elongated grains that consist of astronomical silicates or organic refractory material. Pure graphite grains with diameters of 0.2 to 0.4 micrometer experience a solar radiation pressure force as much as twice the force of solar gravity.

Cosmic Dust↗
NASA NTRS1996

Experimental and computational investigation of lift-enhancing tabs on a multi-element airfoil

An experimental and computational investigation of the effect of lift enhancing tabs on a two-element airfoil was conducted. The objective of the study was to develop an understanding of the flow physics associated with lift enhancing tabs on a multi-element airfoil. A NACA 63(sub 2)-215 ModB airfoil with a 30 percent chord Fowler flap was tested in the NASA Ames 7 by 10 foot wind tunnel. Lift enhancing tabs of various heights were tested on both the main element and the flap for a variety of flap riggings. Computations of the flow over the two-element airfoil were performed using the two-dimensional incompressible Navier-Stokes code INS2D-UP. The computer results predict all of the trends in the experimental data quite well. When the flow over the flap upper surface is attached, tabs mounted at the main element trailing edge (cove tabs) produce very little change in lift. At high flap deflections. however, the flow over the flap is separated and cove tabs produce large increases in lift and corresponding reductions in drag by eliminating the separated flow. Cove tabs permit high flap deflection angles to be achieved and reduce the sensitivity of the airfoil lift to the size of the flap gap. Tabs attached to the flap training edge (flap tabs) are effective at increasing lift without significantly increasing drag. A combination of a cove tab and a flap tab increased the airfoil lift coefficient by 11 percent relative to the highest lift tab coefficient achieved by any baseline configuration at an angle of attack of zero percent and the maximum lift coefficient was increased by more than 3 percent. A simple analytic model based on potential flow was developed to provide a more detailed understanding of how lift enhancing tabs work. The tabs were modeled by a point vortex at the training edge. Sensitivity relationships were derived which provide a mathematical basis for explaining the effects of lift enhancing tabs on a multi-element airfoil. Results of the modeling effort indicate that the dominant effects of the tabs on the pressure distribution of each element of the airfoil can be captured with a potential flow model for cases with no flow separation.

Ashby, Dale↗
NASA NTRS1990

Large deflection random response of a pipe containing fluid flow subjected to random loading

An analytic approach is developed for beam type pipes undergoing large deflections subjected to random loadings. The influence of fluid velocity on the random response is investigated. The root-mean-square (rms) deflections and frequencies for different sound spectrum level values are determined for pipes with both ends either simply supported or clamped. The required number of modes to achieve accurate rms deflections and strains is also studied. The prediction of fatigue life is then based on obtained rms maximum stress. This analytical investigation will help to broaden the basic understanding of the role of fluid flow within structures subjected to acoustic loading.

Chiang, C. K.↗
NASA NTRS1980

On minimal surfaces, membranes and compressible flows

The theory, variational formulation and finite element analysis of a class of nonlinear problems arising in optimization, thin membrane deflection and compressible flows are developed. Error estimates are summarized, and representative numerical results are presented. Particular theoretical questions pertaining to the existence and uniqueness of solutions are addressed, and their implications for such applications of finite element analysis as the study of compressible flows indicated.

Carey, G. F.↗
NASA NTRS1984

Circulation control technology applied to propulsive high lift systems

Technology developed for the Circulation Control Wing high-lift system has been extended to augment lift by entraining and redirecting engine thrust. Ejecting a thin jet sheet tangentially over a small curved deflecting surface adjacent to the slipstream of a turbofan engine causes the slipstream to flow around that deflecting surface. The angle of deflection is controlled pneumatically by varying the momentum of the thin jet sheet. The downward momentum of the slipstream enhances wing lift. This concept of pneumatically deflecting the slipstream has been applied to an upper surface blowing high-lift system and to a thrust deflecting system. The capability of the pneumatic upper surface blowing system was demonstrated in a series of investigations using a wind tunnel model and the NASA Quiet Short-haul Research Aircraft (QSRA). Full-scale thrust deflections greater than 90 deg were achieved. This mechanically simple system can provide increased maneuverability, heavy lift or overload capability, or short takeoff and landing performance.

Englar, R. J.↗
NASA NTRSDate not supplied

Active Flow Control Enhanced Aileron of the High-Lift Common Research Model at Takeoff Condition

An experimental investigation was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel on the NASA 10% scale High-Lift Common Research Model (CRM-HL) to improve the high-lift aerodynamic performance of the takeoff configuration. Active flow control (AFC) was applied at the aileron hinge line to control flow separation at high aileron deflection angles to increase lift-to-drag ratio (L/D). Improvements in low speed L/D can increase vehicle payload and/or range resulting in a more efficient vehicle. Aileron deflection angles of 0°, 7.5°, 16°, and 25° were investigated. Flow control was applied to the two largest aileron deflections, which are considered the high-lift (HL) improved takeoff configurations. A companion paper will discuss baseline flow characteristics of the CRM-HL at the three takeoff conditions: reference, nominal, and HL-improved. In this paper, we focus on the aerodynamic improvement obtained when AFC was applied to an aileron deflected at 16° relative to the nominal configuration of 7.5° deflection. Multiple flow control parameters, including actuator type, spacing, and intensity, were investigated to evaluate the efficiency of the actuation system. The different AFC configurations tested were assessed with tuft visualization, steady surface pressure data, and force and moment data. The results indicated that all actuation types and spacings examined led to an increase in lift across the range of angles of attack investigated. Flow separation was mitigated with the injection of momentum at the aileron hinge line. The configurations with the smallest spacing produced the highest improvement in L/D. Steady jet actuation showed higher efficiency but similar aerodynamic performance when compared to the sweeping jet actuators. This work was performed in support of the NASA Advanced Air Transport Technology (AATT) Project.

CRM-HL↗
NASA NTRS1971

Cross-flow blowing of a two-dimensional stationary arc.

It is demonstrated in an analysis that the electrons emitted from the cathode undergo collisions with the heavy particles and are deflected in the flow direction by the component of a collisional force associated with the relative difference in flow velocities between electrons and heavy particles. The resultant motion of the electrons describing the arc is thus caused by a combined action of the collisional force that results from the externally applied electric field. An expression is given which enables computation of the arc shape to be made provided the velocity distribution of the cross-flow and the distribution of the externally applied electric field are prescribed.

Bose, T. K.↗
NASA NTRS2004

Concentration Measurements in Self-Excited, Momentum-Dominated Helium Jets

Flow structure of momentum-dominated pure helium jets discharged vertically into ambient air was investigated using high-speed rainbow schlieren deflectometry (RSD) technique. Effects of the operating parameters, i.e., Reynolds number (Re) and Richardson number (Ri), on the oscillatory behavior of the flow were examined over a range of experimental conditions. To seek the individual effect of these parameters, one of them was fixed and the other was varied with certain constraints. Measurements revealed highly periodic oscillations in the laminar region as well as high regularity in transition and turbulent regions. Maximum spectral power profiles at different axial locations indicated the oscillation amplitude increasing until the breakdown of the jet in the turbulent regime. The transition from the laminar to turbulent flow was also investigated. Fast Fourier transform analysis performed in the transition regime showed that the flow oscillates at a unique frequency, which was the same in the upstream laminar flow region. Measured deflection angle data were used in Abel inversion algorithm to construct the helium concentration fields. Instantaneous helium concentration contours revealed changes in the flow structure and evolution of vortical structures during an oscillation cycle. Temporal evolution plots of helium concentration at different axial location showed repeatable oscillations at all axial and radial locations up to the turbulent regime. A cross-correlation technique, applied to find the spatial displacements of the vortical structures, provided correlation coefficient peaks between consecutive schlieren images. Results show that the vortical structure convected and accelerated only in the axial direction.

Yildirim, Bekir Sedat↗
NASA NTRS1997

Thrust reverser with variable nozzle

A thrust reverser is provided for both modulating and reversing bypass flow discharged from a fan through a bypass duct of a turbofan gas turbine engine. The reverser includes an aft cowl joined to a forward cowl and having an aft end surrounding a core engine to define a discharge fan nozzle of minimum flow throat area. The aft cowl is axially translatable relative to the forward cowl from a first position fully retracted against the forward cowl, to a second position partially extended from the forward cowl, and to a third position fully extended from the forward cowl. A plurality of cascade turning vanes are disposed between the forward and aft cowls, and a plurality of thrust reversing deflector doors are pivotally mounted to the aft cowl and bound the bypass duct. The deflector doors are selectively deployed from a stowed position corresponding with the first and second positions of the aft cowl for allowing unrestricted flow of the bypass flow through the fan nozzle. The doors also have a deployed position corresponding with the third position of the aft cowl for substantially deflecting the bypass flow from discharging through the fan nozzle to discharging through the cascade vanes for effecting thrust reverse. Axial translation of the aft cowl between the first and second positions varies flow area of the fan nozzle to vary thrust effected by the discharged bypass flow.

Butler, Lawrence↗
NASA NTRS2016

Meeting the Grand Challenge of Protecting Astronauts Health: Electrostatic Active Space Radiation Shielding for Deep Space Missions

This report describes the research completed during 2011 for the NASA Innovative Advanced Concepts (NIAC) project. The research is motivated by the desire to safely send humans in deep space missions and to keep radiation exposures within permitted limits. To this end current material shielding, developed for low earth orbit missions, is not a viable option due to payload and cost penalties. The active radiation shielding is the path forward for such missions. To achieve active space radiation shielding innovative large lightweight gossamer space structures are used. The goal is to deflect enough positive ions without attracting negatively charged plasma and to investigate if a charged Gossamer structure can perform charge deflections without significant structural instabilities occurring. In this study different innovative configurations are explored to design an optimum active shielding. In addition, to establish technological feasibility experiments are performed with up to 10kV of membrane charging, and an electron flux source with up to 5keV of energy and 5mA of current. While these charge flux energy levels are much less than those encountered in space, the fundamental coupled interaction of charged Gossamer structures with the ambient charge flux can be experimentally investigated. Of interest are, will the EIMS remain inflated during the charge deflections, and are there visible charge flux interactions. Aluminum coated Mylar membrane prototype structures are created to test their inflation capability using electrostatic charging. To simulate the charge flux, a 5keV electron emitter is utilized. The remaining charge flux at the end of the test chamber is measured with a Faraday cup mounted on a movable boom. A range of experiments with this electron emitter and detector were performed within a 30x60cm vacuum chamber with vacuum environment capability of 10-7 Torr. Experiments are performed with the charge flux aimed at the electrostatically inflated membrane structure (EIMS) in both charged and uncharged configurations. The amount of charge shielding behind and around the EIMS was studied for different combinations of membrane structure voltages and electron energies. Both passive and active shielding were observed, with active shielding capable of deflecting nearly all incoming electrons. The pattern of charge distribution around the structure was studied as well as the stability of the structures in the charge flow. The charge deflection experiments illustrate that the EIMS remain inflated during charge deflection, but will experience small amplitude oscillations. Investigations were performed to determine a potential cause of the vibrations. It is postulated these vibrations are due to the charge flux causing local membrane charge distribution changes. As the membrane structure inflation pressure is changed, the shape responds, and causes the observed sustained vibration. Having identified this phenomenon is important when considering electrostatically inflated membrane structures (EIMS) in a space environment. Additionally, this project included a study of membrane material impacts, specifically the impact of membrane thickness. Extremely thin materials presented new challenges with vacuum preparation techniques and rapid charging. The thinner and lighter membrane materials were successfully inflated using electrostatic forces in a vacuum chamber. However, care must be taken when varying the potentials of such lighter structures as the currents can cause local heating and melting of the very thin membranes. Lastly, a preliminary analysis is performed to study rough order of magnitude power requirements for using EIMS for radiation shielding. The EIMS power requirement becomes increasingly more challenging as the spacecraft voltage is increased. As a result, the emphasis is on the deflection of charges away from the spacecraft rather than totally stopping them. This significantly alleviates the initial power requirements. With modest technological development(s) active shielding is emerging to be a viable option.

Radiation↗