Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLYING BOATS - RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1942

The Longitudinal Stability of Flying Boats as Determined by Tests of Models in the NACA Tank II : Effect of Variations in Form of Hull on Longitudinal Stability

Data taken from tests at constant speed to establish trim limits of stability, tests at accelerated speeds to determine stable limits of center of gravity shift, and tests at decelerated speeds to obtain landing characteristics of several model hull forms were used to establish hull design effect on longitudinal stability of porpoising. Results show a reduction of dead rise angle as being the only investigated factor reducing low trim limit. Various methods of reducing afterbody interference increased upper trim limit

Olson, Roland E.↗
NASA NTRS1945

The Effect of Afterbody Length of the Hydrodynamic Stability of a Dynamic Model of a Flying Boat: Langley Tank Model 134

A program of model tests has been completed at Langley tank no. 1 which will furnish a qualitative guide as to the relation of length of afterbody and depth of step. The model used for the tests was a l/12-size unpowered dynamic model of a hypothetical 160,000-pound airplane. The results showed that an increase in length of afterbody requires an accompanying increase in depth of step to maintain adequate landing stability. Changing the length of afterbody and depth of step in such a manner as to maintain a given landing stability will result in only small changes in take-off stability.

Land, Norman S↗
NASA NTRS1933

A Complete Tank Test of a Model of a Flying-Boat Hull - N.A.C.A. Model No.11

This note discusses the limitations of the conventional tank test of a seaplane model. The advantages of a complete test, giving the characteristics of the model at all speeds, loads, and trim angles in the useful range are pointed out. The data on N.A.C.A. Model No.11, obtained from a complete test, are presented and discussed. The results are analyzed to determine the best trim angle for each speed and load. The data for the best angles are reduced to non-dimensional form for ease of comparison and application. A practical problem using the characteristics of model no.11 is presented to show the method of calculating the take-off time and run of a seaplane from these data.

Shoemaker, James M.↗
NASA NTRS1941

Tests of Round and Flat Spoilers on a Tapered Wing in the NACA 19-Foot Pressure Wind Tunnel

Several arrangements of round and flat spanwise spoilers attached to the upper surface of a tapered wing were tested in the NACA 19-foot pressure wind tunnel to determine the most effective type, location, and size of spoiler necessary to reduce greatly the lift on the wings of large flying boats when moored. The effect of the various spoilers on the lift, the drag, and the pitching-moment characteristics of the tapered wing was measured over a range of angles of attack from zero to maximum lift. The most effective type of spoiler was found to be the flat type with no space between it and the wing surface. The chordwise location of such a spoiler was not critical within the range investigated, from 5 to 20 percent of the wing chord from the leading edge.

Wenzinger, Carl J↗
NASA NTRS1921

Ground influence on airfoils

The question of ground influence on airplanes has recently attracted some attention in view of the claims made by certain designers that the landing speed of their airplanes is much decreased by an increase in lift coefficient due to the proximity of the ground in landing. The results of wind tunnel tests indicate that ground effect is not entirely beneficial. It decreases the landing speed and cushions the landing shock somewhat. However, it does so at the expense of an increased length of preliminary skimming over the ground. By decreasing the drag and increasing the lift, it lengthens the distance necessary for the airplane to travel before losing enough speed to land. On the other hand, its influence is helpful in taking off, especially in the case of flying boats with their low-lying wings. In the conventional tractor airplane, the height of the wings above the ground is determined largely by propeller clearance. However, a small low-speed airplane like the Pischoff and large low-speed commercial aircraft with engines between wings can utilize ground influence to good advantage.

Raymond, Arthur E↗
NASA NTRS1946

Consideration of dynamic loads on the vertical tail by the theory of flat yawing maneuvers

Dynamic yawing effects on vertical tail loads are considered by a theory of flat yawing maneuvers. A comparison is shown between computed loads and the loads measured in flight in a fighter airplane. The dynamic effects were investigated on a large flying boat for both an abrupt rudder deflection and a sinusoidal rudder deflection. Only a moderate amount of control deflection was found to be necessary to attain the ultimate design load on the tail. In order to take into account dynamic effects in design, specifications of yawing maneuverability or control movement are needed.

Boshar, John↗
NASA NTRS1927

Experiments on airfoils with trailing edge cut away

Airfoils with their trailing edge cut away are often found on aircraft, as the fins on the hulls of flying boats and the central section of the wings for affording better visibility. It was therefore of some interest to discover the effect of such cutaways on the lift and drag and on the position of the center of pressure. For this purpose, systematic experiments were performed on two different airfoils, a symmetrical airfoil and an airfoil of medium thickness, with successive shortenings of their chords.

AIRFOILS↗