Search NASA⌕ Search

SEARCH · Search NASA

Results for “FUEL PELLETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Spark plasma sintering (SPS) densified U 3 Si 2 pellets: Microstructure control and enhanced mechanical and oxidation properties

Dense U 3 Si 2 pellets with controlled grain structure and enhanced thermal-mechanical and oxidation properties are synthesized with spark plasma sintering (SPS). Microstructure and phase composition of the SPS densified pellets are characterized systematically using SEM, EDS, and XRD. Thermal-mechanical properties and oxidation behavior of the sintered silicide fuel pellets are analyzed by laser flash, indentation, and dynamic thermogravimetric analysis. Dense U 3 Si 2 pellets are consolidated by combining high energy ball milling and rapid sintering by SPS, and the microstructure structures are controlled from micron-sized (~5.7 μm grain size) for conventional silicide to a nanocrystalline matrix with an average grain size of ~280 nm. A dominant phase of distorted U 3 Si 2 was identified with lattice expansion due to residual thermal stress upon SPS consolidation and rapid cooling processes. Both micron-sized and nano-sized pellets show exceptional thermal transport properties, consistent with monolithic silicides reported in literature. The SPS-densified pellets possess simultaneously high hardness and fracture toughness. The SPS-densified silicide pellets also demonstrate exceptional oxidation performance with extended onset oxidation temperature above 500 °C and reduced oxidation kinetics, particularly for nano-sized pellets. A strong strain effect was proposed in which compressive stress in nano-sized pellets enhances the oxidation resistance of silicide fuels, as evidenced by the degradation of oxidation performance upon strain relaxation by isothermal annealing. The correlation among the sintering process – microstructure control – physical properties and fuel behavior is established. A new concept of strain engineering is proposed further properties optimization, enabling the development of potential oxidation and corrosion-resistant silicides with extended performance, the key technological challenge of U 3 Si 2 as the leading concept of accident tolerant fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

040226_AnnularFuel_FuelPerformance_LRSv2

This slide deck summarizes a comparative fuel performance assessment of four annular fuel concepts for pressurized water reactor applications against a reference 17×17 fuel design. Overall, annular fuel geometry improves several key thermal-mechanical performance metrics, with the large-annulus configuration providing the most favorable balance of benefits. Relative to the reference design, annular fuel reduces peak fuel temperature by lowering thermal resistance through a thinner fuel pellet and smaller heat-conduction path. At the same time, the reduced fuel volume raises local burnup and correspondingly increases fission gas release. Despite this, rod internal pressure at end of life decreases because the annular geometry provides greater internal void volume. Annular designs also tend to delay fuel-cladding gap closure, although this advantage diminishes in thin-gap configurations where the smaller initial gap accelerates closure. Similarly, hoop stress and hoop strain are generally reduced for annular fuel, but both increase as the initial gap becomes smaller, indicating a potential cladding integrity concern for thin-gap designs. Corrosion performance shows no meaningful variation among the concepts considered. Taken together, the results indicate that annular fuel can offer significant performance advantages in a PWR environment, with large-annulus designs emerging as the strongest candidate while thin-gap geometries introduce more challenging mechanical margins.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Cluster Dynamics Simulations of Intra-Granular Fission Gas Bubble Size and Pressure Evolution in UO 2

Fission gases such as xenon (Xe) play a critical role in determining the behavior and response of nuclear fuel. Given that Xe has little solubility in UO 2 , it accumulates and forms bubbles, which significantly impact fuel performance. Intra- and inter-granular bubble nucleation and growth can lead to fuel swelling, and once bubbles interconnect at grain boundaries, fission gas can be released into the plenum. At low temperatures, limited uranium vacancy mobility can restrict swelling, therefore causing the bubbles to become highly pressurized. Consequently, this can induce micro-cracking, promote fission gas release (increasing the likelihood of cladding failure), and even lead to fuel pulverization under accident conditions such as a loss of coolant accident. As bubble evolution is strongly influenced by local temperature and fission rate, markedly different behavior occurs across the radial profile of the fuel pellet. Capturing the mechanisms that underpin bubble evolution is therefore important to predict these behaviors in the fuel. Previous models describing important mechanisms informed by lower length scale simulations have been developed under the NEAMS program. These can describe the evolution of a single bubble type (i.e., single value for radius and pressure) at each position in the pellet, for instance using the Centipede cluster dynamic code. However, in reality, a full distribution in bubble sizes and pressures exists within the microstructure at a given position in the pellet. To address this the cluster dynamics code Xolotl, which can predict Xe and vacancy phase space (i.e., bubble distributions) for intra-granular bubbles, has been used before. Prior work benchmarked the Xolotl code against the Centipede cluster dynamics code to ensure compatibility and to verify that mobile defect properties are adequately transferred between the two codes, along with some physics improvements. In this work, we go further by introducing a physics-based set of improvements that will allow us to accurately predict bubble size distributions and internal bubble pressures under representative UO 2 irradiation conditions. The improvements include (i) coupling bubble-defect reaction energies to a virial equation of state (EOS), (ii) including a bubble surface tension contribution, (iii) incorporating radiation-induced re-solution of Xe and vacancies, (iv) enabling pressure-driven dislocation loop punching through an effective emission of interstitial clusters informed by interstitial loop energetics, (v) accounting for radiation induced athermal diffusion of Xe, and (vi) implementing a Booth-type grain boundary sink representation for all mobile defects and defect clusters. After these modifications, we observe good agreement of Xolotl fission gas bubble size and concentration predictions with legacy experimental measurements. Additionally, it allows the distribution of Xe bubble pressures and radius to also be predicted and compared to data produced through the Advanced Fuels Campaign (AFC) program. Here, we have done this by running simulations under conditions similar to the AFC post-irradiation examination (PIE) samples irradiated at North Anna 2 light water reactor (LWR). Our results shows excellent agreement with these experimental measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1972

Fabrication of fuel pin assemblies, phase 3

Five full size and eight reduced length fuel pins were fabricated for irradiation testing to evaluate design concepts for a fast spectrum lithium cooled compact space power reactor. These assemblies consisted of uranium mononitride fuel pellets encased in a T-111 (Ta-8W-2Hf) clad with a tungsten barrier separating fuel and clad. Fabrication procedures were fully qualified by process development and assembly qualification tests. Detailed specifications and procedures were written for the fabrication and assembly of prototype fuel pins.

Keeton, A. R.↗
DOE OSTI2025

Design of a separate effects MiniFuel irradiation experiment investigating microstructure evolution in high burnup UO 2

The microstructural evolution of UO 2 fuel pellets during commercial operation in light water reactors (LWRs) is known to vary significantly across the pellet radius due to spatial variations in local temperature and burnup. The primary obstacle to extending LWR refueling cycles to 24-month intervals is the susceptibility of certain high burnup fuel microstructures to fuel fragmentation, relocation, and dispersal (FFRD) during a loss of coolant accident (LOCA). Although FFRD of the high burnup structure in the rim region of a pellet is well studied, the fine fragmentation that has been observed in a second region, near the midradius of the pellet (termed the “dark zone”) following mock LOCA testing of high burnup commercial fuel rods is less understood. This paper describes the design, analysis, and execution of a separate effects MiniFuel irradiation experiment that aims to identify the specific temperature and burnup regimes under which FFRD-susceptible dark zone microstructures form. The small disc specimens (3 mm diameter by ∼0.3 mm thick) enable more precise control of the relatively uniform temperature and burnup conditions. A total of 42 specimens were fabricated with typical LWR fuel densities (∼96%–98% of theoretical density) and grain sizes (∼12 μm) and are being irradiated over a range of temperatures (600°C–1000°C) and discharge burnups (50–72 MWd/kg-U) that bound the midradius region of high burnup LWR fuel. Fuel specimens with identical 235 U enrichments were inserted in two irradiation locations in the High Flux Isotope Reactor and are currently undergoing irradiation to further evaluate the impact of rate effects (fission rate, time at temperature) on the microstructural evolution. The fuel fabrication and the thermal and neutronic simulations used for designing the experiment are detailed in this paper. A secondary objective of the experiment is to observe fission gas release (FGR) under the various irradiation conditions, and this work provides first-order predictions of FGR from all fuel specimens. The insights gained from these experiments will inform future high burnup core designs that could minimize the formation of susceptible microstructures and ultimately enable 24-month refueling cycles while minimizing the fraction of the fuel susceptible to FFRD.

FFRD↗
DOE OSTI2024

Prediction of pellet mass thresholds for ELM triggering in low-collisionality, ITER-like discharges

Abstract In ITER, pellets are calculated to require more than 8 times the mass than currently planned to reliably trigger edge-localized modes (ELMs). Unmitigated heat flux impulses from ELMs are intolerable in ITER at full power and current. Therefore, ITER operation relies on multiple approaches to control ELM heat fluxes. One method is pellet ELM pacing to instigate small rapid ELMs with low heat flux. Predicting the performance of pellet pacing is critical for ITER, which is expected to operate in a regime with a low-collisionality, peeling-limited pedestal. However, to trigger ELMs the local pressure increase in the expanding pellet cloud pushes the equilibrium over the ballooning stability limit. In this work, linear and nonlinear M3D-C1 simulations are used to predict pellet mass thresholds in DIII-D discharges and ITER scenarios with peeling-limited pedestals. It is found that the distance of the equilibrium’s operational point from the ballooning branch of the pedestal stability boundary strongly changes thresholds. Linear M3D-C1 simulations find a strong dependence of the pellet mass threshold on the poloidal injection location for ITER’s 15 MA, Q = 10 scenario. The required pellet mass at the planned injection locations is 8 to 17 times larger than currently considered. However, such linear simulations do not include pellet ablation physics or time evolution of density and temperature. A new scheme of 2D nonlinear simulations, coupled with linear stability analysis at various steps throughout the nonlinear time evolution, was developed to include such physics and improve on the linear results. These new nonlinear-to-linear simulations confirm previous findings. This result suggests that pellet ELM triggering in ITER could require pellets much larger than those currently planned, which makes ELM-pacing operationally challenging. On the other hand, fueling pellets injected from the high-field side will likely not unintentionally trigger ELMs in an otherwise ELM-stable plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Evaluating Nuclear Forensic Signatures for Advanced Reactor Deployment: A Research Priority Assessment

The development and deployment of a new generation of nuclear reactors necessitates a thorough evaluation of techniques used to characterize nuclear materials for nuclear forensic applications. Advanced fuels proposed for use in these reactors present both challenges and opportunities for the nuclear forensic field. Many efforts in pre-detonation nuclear forensics are currently focused on the analysis of uranium oxides, uranium ore concentrates, and fuel pellets since these materials have historically been found outside of regulatory control. The increasing use of TRISO particles, metal fuels, molten fuel salts, and novel ceramic fuels will require an expansion of the current nuclear forensic suite of signatures to accommodate the different physical dimensions, chemical compositions, and material properties of these advanced fuel forms. In this work, a semi-quantitative priority scoring system is introduced to identify the order in which the nuclear forensics community should pursue research and development on material signatures for advanced reactor designs. This scoring system was applied to propose the following priority ranking of six major advanced reactor categories: (1) molten salt reactor (MSR), (2) liquid metal-cooled reactor (LMR), (3) very-high-temperature reactor (VHTR), (4) fluoride-salt-cooled high-temperature reactor (FHR), (5) gas-cooled fast reactor (GFR), and (6) supercritical water-cooled reactor (SWCR).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Preliminary Testing of a Continuous Cryopump for Primary Fusion Device Pumping and Direct Internal Recycling

Here, the concept of directly recirculating fusion machine exhaust gas, bypassing the tritium plant, to make fuel pellets was proposed in the 1990s and later termed direct internal recycling (DIR). In the DIR concept, the residual fusion fuel in the machine exhaust stream is separated from impurities locally and diverted directly to the fueling systems, bypassing isotopic separation and other processing equipment, and therefore significantly reducing the required size of the fuel processing plant, reducing plant inventory, and thus increasing the economic viability of fusion as an energy source. One concept for DIR consists of a series of cryogenic pumps to separate the impurities from the machine exhaust gas using different triple point temperatures and saturation curves of exhaust constituents. In this concept, the plasma exhaust is initially passed through an impurity trap operating at ~25–30 K to desublimate impurities such as hydrocarbons, argon, oxygen, and nitrogen. The resulting process stream will consist of DT fuel and helium. The process stream is then pumped by a continuous cryopump known as a “snail pump.” This pump is a steady-state continuous cryopump that desublimates all remaining exhaust gas constituents while allowing helium, a byproduct of the fusion reaction, to pass through. The helium is pumped to the tritium plant for processing while the desublimated material is continuously scraped off, heated up, and transported to the fueling system. This article will present the cryogenic DIR concept and outline the design and operation of the snail pump, along with results from preliminary testing. Tests to assess pumping and separation efficiency found that at D2 flows below 50.7 Pa ⋅ m3/s with 1% helium, the pump is capable of pumping and separating the gas with a resulting DIR fraction of >99%, with no helium entrained in the primary fuel exhaust stream. The main limitation is due to the thermal performance of the cryogenic circuits of the pump, which will be addressed in future testing.

Gebhart III, Trey E. [Oak Ridge National Laborator↗
DOE OSTI2023

Evaluation of Thermal Neutron Scattering Cross Section of Uranium Silicide with Ab Initio Lattice Dynamics

Uranium silicide (U 3 Si 2 ) is a candidate material for the high-density nuclear fuel in commercial light water reactors [1], [2]. Its higher uranium density, 11.3 g-U/cm3, compared to that of uranium dioxide (UO 2 ), 9.7 g-U/cm3, can improve the performance of a nuclear reactor while using low enriched uranium (LEU) and diversify the choice of cladding materials [1]–[3]. It also has a higher thermal conductivity than UO 2 , which can reduce the thermal stress on the material caused by a temperature gradient across the fuel pellet and provide a larger margin for some postulated accidents [1], [2], [4]. Furthermore, compared to U3Si, another high-density fuel candidate, it has better resistance to in-pile swelling due to less irradiation-induced rapid amorphization [1], [3]. Corresponding to its importance in nuclear engineering, many previous studies have reported the properties of U3Si2. Experiments showed that U 3 Si 2 is a paramagnetic (PM) metal, where a slight linear increase in magnetic susceptibility was measured with increasing temperature [5], [6]. In addition, thermodynamic quantities such as thermal expansion coefficient, heat capacity, and thermal conductivity were experimentally determined over a wide temperature range [1], [7], [8]. In several computational studies, ab initio atomistic simulations based on density functional theory (DFT) were performed to calculate various properties including elastic constants, electronic density of states (DOS), and phonon dispersion curves [9]–[12]. Nevertheless, thermal neutron scattering cross sections, which are critical to the prediction of the parameters in reactor physics that are ultimately related to reactor criticality, have not yet been evaluated for U3Si2. The scattering cross section can be calculated from the phonon DOS, or the energy spectrum of lattice vibrations, of the crystalline system [13], [14]. However, there is also no experimental data available for the phonon DOS of U 3 Si 2 . While some computational studies reported the phonon DOS and/or dispersion curves from ab initio simulations [9]–[12], the accuracy cannot be guaranteed because it is unclear whether the spin-polarization behavior of PM U 3 Si 2 was properly described. In the present study, the thermal neutron scattering cross section for U 3 Si 2 is evaluated for the first time by calculating the phonon DOS for U3Si2 from ab initio lattice dynamics (AILD) simulations based on DFT. First, U 3 Si 2 is modeled based on the experimental structure, and AILD simulations are performed on the modeled U3Si2 to optimize the structure. Next, AILD simulations are performed for supercells with atomic displacement to calculate Hellmann-Feynman forces. Based on the calculated forces, partial phonon DOSs for U and Si are obtained, and the thermal neutron scattering law (TSL) for U 3 Si 2 is finally evaluated. To verify the accuracy of the calculations in the present study, the calculation results are compared with experimental data on the structure and heat capacity of U3Si2 [1], [7], [8], [15].

Geometry Optimization↗
DOE OSTI2022

Optimization of particle tracking methods for stochastic media

Random media emerge in several applications involving particle transport, encompassing e.g. photon propagation through Rayleigh-Taylor instabilities in fuel pellets for inertial confinement fusion, or neutron multiplication problems related to the assessment of re-criticality risk following severe accidents with fuel degradation. Reference calculations in such material configurations by means of Monte Carlo transport codes are particularly challenging, since high-density stochastic media might involve several hundreds of thousands of volumes and thus make particle tracking routines extremely cumbersome. In order to cope with these issues, two distinct strategies have been proposed so far: the use of neighbor maps, or the use of delta tracking. In this work we will compare these methods and illustrate their specific merits and drawbacks, as taken both alone and in combination with each other. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Mechanical response and microstructure evolution from multiaxial stress relaxation in textured zircaloy nuclear cladding

Modern energy markets provide motivation for nuclear reactors to increase operational flexibility and load following capacity of existing reactor designs. The operational power changes result in fuel pellet expansion and contraction resulting in pellet-cladding mechanical interaction (PCMI) and high cladding stresses that are strongly related to stressed corrosion cracking (SCC) which can lead to fuel rod failure. This work aims to quantify the stress fields in cladding with a focus on multiaxial stress relaxation response from an imposed strain and the resulting microstructure changes in textured zircaloy claddings. Stress relaxation tests resulting in multiaxial stress fields are performed to measure the material response of Zircaloy-4 nuclear cladding. Multiple experiments using samples from the same piece of cladding are performed so samples with the same processing history may be removed at strategic points throughout mechanical testing for microstructure characterization. The microstructure evolution is analyzed with mechanical response to evaluate the static recovery impact on crystallographic texture and grain morphology. Experiments are performed at Idaho National Laboratory using an experimental device capable of applying internal pressure and independent axial load to commercial nuclear cladding at elevated temperatures with stress- or strain-controlled experimental capability. X-ray diffraction and electron backscatter diffraction are used for microstructure analysis. Rheological models are used to visualize the multiaxial stress-strain relationships and isolate elastic, plastic, and viscoplastic material properties for analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Reactor and fuel cycle performance of light water reactor fuel with 235 U enrichments above 5%

Recent advances in nuclear fuel materials research, particularly on the topic of accident-tolerant fuels, have brought up potential opportunities for expanding the operating envelope of existing light water reactors. As many of the performance improvements offered by these technologies may be most fully realized by increasing fuel enrichment beyond the standard 5% limit, this paper examines the potential reactor performance and fuel cycle performance of low-enriched uranium oxide fueled light water reactors by generically considering pressurized water reactors with 235 U enrichment from 5 to 7%. Advanced cladding, including accident-tolerant cladding, has the potential to increase fuel burnup limits related to hydrogen in the cladding that coincide with those limits associated with end-of-life reactivity. Therefore, higher enrichment will be necessary in order to realize the higher fuel burnups. This work includes evaluation of the fuel cycle length, discharge burnup, reactivity coefficients, and fuel cycle performance, including radioactive waste and environmental impact metrics per unit energy generated. The analysis was performed using the evaluation metrics from the US Department of Energy Office of Nuclear Energy Fuel Cycle Evaluation and Screening Study. The reactor performance and safety analysis show that enrichments between 5 and 7% would have similar fuel temperature and moderator temperature coefficients. However, the soluble boron coefficient would decrease in magnitude, requiring more corrosive boric acid in the coolant or other methods of reactivity control during the fuel cycle. At these higher enrichments the maximum burnup at the rim of the fuel pellet would increase by almost a factor of two, which is expected to impact the formation of high-burnup structure in the fuel and the corresponding thermo-mechanical fuel properties. The fuel cycle performance assessment shows that increasing enrichment reduces the quantity of high-level waste disposed per unit energy generated, but it increases the natural resource requirements normalized to a gigawatt-electricity-per-year basis. Another impact is the slightly higher discharge burnup, resulting in somewhat different activity levels of the spent nuclear fuel and high-level waste radioactivity at 100 and 100,000 years after fuel discharge. The environmental impacts—including land use, water use, carbon emission, and radiological exposure—are of the same magnitude per unit energy generated. Finally, however, the impacts are distributed differently. Less than 5% enrichment has marginally more impact on the back-end of the fuel cycle, and greater than 5% enrichment has marginally more impact on the front-end of the fuel cycle. Ultimately, no neutronic or reactor safety hindrances to employing light water reactor fuel with enrichments greater than 5% are identified; given the achievable reactor performance benefits with advanced fuels, further practical exploration of increased enrichment fuel is recommended.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Simultaneous Isotopic Analysis of U, Pu, and Am in Spent Nuclear Fuel by Resonance Ionization Mass Spectrometry

Solid samples of spent nuclear fuel were analyzed for actinide isotopic composition by resonance ionization mass spectrometry. Isotopes of U, Pu, and Am were simultaneously quantified using a new method that removes and/or resolves the isobaric interferences at 238 U/ 238 Pu and 241 Pu/ 241 Am without sample preparation other than cutting and mounting small (~10 μm) samples. Trends in burnup and neutron capture product distributions were correlated with the sampling positions inside the reactor. Overall, the results show the skin effect, in which the core and near-edge regions of a fuel pellet exhibit strong differences in actinide concentrations and isotope distributions due to differences in the neutron energy spectra between the pellet rim and the core. While no elemental concentration measurements were made, the ability to measure the 238 Pu/ 239 Pu ratio in the presence of a 7400× excess of 238 U enabled an estimate of the enhancement in Pu concentration due to the skin effect at the rim of the pellet.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Mechanistic verification of empirical UO 2 fuel fracture models

Standard UO 2 fuel pellets used in light-water reactors fracture during irradiation due to the large thermal gradient in the radial direction. Over the decades, numerous researchers have explored fuel cracking from experimental and modeling points of view. To date, there have been both empirical and mechanistic approaches to predict the number of fragments that form in UO 2 . The empirical models only consider maximum power and burnup as inputs. Existing mechanistic approaches for normal operation have not accounted for irradiation effects. Here, this work employs a mechanistic fuel cracking model using the extended finite element method to explore radial crack formation while including a sensitivity analysis that accounts for the randomization of tensile strength within the fuel, the strength randomization criteria (uniform or volume-weighted Weibull), power ramping rates, computational mesh density, maximum power level, and irradiation (burnup) effects. The results indicate that the uncertainty in this mechanistic modeling approach envelopes the predicted values from three different empirical correlations in almost all cases. This means that, for computationally intensive analyses involving UO 2 fragmentation, the empirical correlations can be used. However, since the mechanistic calculations bound those of the empirical correlations, there is confidence in the applicability of the mechanistic approach developed in this work to generate a correlation for fuel types where limited data exists (e.g., doped-UO 2 , U 3 Si 2 ).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Fabrication and Characterization of Single-Particle Compacts

The programmatic objective of the advanced low enriched uranium (aLEU) fuel Project within the Office of Nonproliferation Research and Development (NA-22) is to advance the development of nuclear reactor designs, fuel materials, and fabrication technologies capable of meeting a number of challenging customer requirements, including reactor stability, extended lifetime, and power density without refueling, while using only low-enriched uranium (i.e., less than 20% enrichment of 235 U). The tandem requirements of delivering sufficient power density and maintaining fuel performance over the course of a multidecade fuel lifetime tightly constrain the field of potential fuel options. Monolithic fuel forms (e.g., fuel pellets) provide maximized density of fissile material, but they may face challenges in maintaining their structure and performance over the long reactor lifetimes envisioned in this program. Dispersion fuel forms with an inert matrix provide enhanced long-term stability but sacrifice fissile material density, and they may not provide sufficient power density over the reactor lifetime with the limit of low enrichment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Influence of point defect accumulation on in-pile thermal conductivity degradation: Fuel rod defect distribution and deviation between in-pile and post irradiation thermal conductivity

As nuclear fuel burn-up increases, its thermal conductivity degrades due to the accumulation of defects that lead to increased phonon scattering rates. This results in a rise in the centerline temperature of the fuel rod, whereby heat generation must be decreased to avoid undesired behavior such as fuel melting and extensive fission gas release. Fuel performance codes are utilized to optimize the fuel's operational conditions; while they are based on established physical principles, their empirical nature limits their predictive capabilities. Recently, an effort has been made to develop predictive fuel performance codes for commonly used nuclear fuels, as well as accelerated qualification of advanced nuclear fuels. In this report, we elaborate on the importance of careful analysis of point defects’ impact on thermal conductivity in fuel performance analysis. Further, a model is presented where point defect concentration is estimated based on Rate Theory modeling and used as input to the Klemens-Callaway model to calculate their contribution to the degradation of thermal conductivity in UO 2 under prototypical irradiation conditions. This analysis suggests that point defect concentration is significant at the rim of the fuel pellet and neglecting this leads to underestimation of the centerline temperature, which may have consequences on fission gas behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗