Search NASA⌕ Search

SEARCH · Search NASA

Results for “FUEL SYSTEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Handbook for Performing Hydrocarbon Fuel Fires in XTF For Fast-Heat System Level Tests

This document serves to provide information on all aspects of a system level thermal qualification test including a description of the setup and conduct of a full system fuel fire test in the Thermal Test Complex (TTC) Crosswind Test Facility (XTF). This might be referred to as a “handbook” for future tests. This information is intended to assist technologists and test directors in performing these types of tests in the future.

42 ENGINEERING↗
DOE OSTI2025

Development of a Real-Time Neutron Noise Analysis System for Fuel Debris Removal at Fukushima Daiichi

The decommissioning of Units 1, 2, and 3 at Fukushima Daiichi presents unique challenges, particularly in mitigating the risk of re-criticality during fuel debris removal. Disturbing previously stable debris configurations has the potential to cause changes in the multiplication of the system, necessitating real-time monitoring to ensure operational safety. Current neutron detection systems, primarily passive, are not optimized for continuous real-time analysis and are limited in their ability to detect rapid changes in system reactivity.

Neutron Detection Systems↗
DOE OSTI2021

Fuel Performance Analysis of Chromium-Coated Cladding under Burst Conditions

To reduce the oxidation of zirconium-based alloy cladding at high temperatures, accident tolerant fuel systems have been proposed. Of the concepts identified, chromium-coated cladding has been shown to slow oxidation without greatly impacting the fuel system geometry or neutronic performance. To determine how coated-cladding tubes will perform under high-temperature accident conditions, pressurized-tube burst tests have been performed using the Severe Accident Test Station at Oak Ridge National Laboratory. To begin modeling these tubes to better understand how the coating will impact cladding behavior, these burst tests were simulated with the BISON fuel performance code. Cladding tube surface temperatures for the burst test were developed by fitting thermocouple data into axial and azimuthal profiles, while pressure data were compared until cladding failure. The temperatures at failure and the pressure evolution show relatively good agreement between the simulation and experiment results. This is the first step of a larger effort to simulate the cladding deformation process under high-temperature transient conditions and assess the cladding margin to failure more accurately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Summary of Geometric Parameters and Their Effects on Performance of U-10Mo Fuel Plates

A monolithic plate-type fuel system has been under development to convert high-performance test reactors from highly enriched uranium to low-enrichment uranium fuels and is now moving into the qualification phase, a predecessor to the timely conversion of the target reactors. To qualify this fuel system, the plates must meet safety standards and perform well in a reactor. The plates must maintain mechanical integrity, exhibit geometric stability, and have stable and predictable in-reactor behavior. The requirement to maintain mechanical integrity under normal operating conditions is primarily demonstrated by successful testing. However, each high-performance reactor employs a distinct design, resulting in distinct plate geometries, with unique features, attributes, irregularities, and tolerances. Due to the abundance of such distinct geometric varieties, a single “generic” plate geometry capturing all extremes is not achievable. It is also impractical to test each of these proposed designs in a reactor. This limitation necessitates cautious evaluations since the thermomechanical response of a plate with a certain geometry may not be representative for a plate with a significantly different geometry. To address concerns related to in-reactor plate performance, large set of sensitivity studies were performed. These parametric studies aimed to better understand irradiation performance, while evaluating the sensitivity of results to various modeling inputs, including geometric, operational, and material parameters. This work studied selected geometric parameters based on provided fuel specifications and performed a series of parametric simulations. The resulting temperature, displacement, and stress strains were comparatively evaluated to determine the effects of various geometric parameters. This draft provides a “high-level summary” of our parametric sensitivity studies and summarizes the key findings.

42 ENGINEERING↗
DOE OSTI2021

Destructive Examination of a FeCrAl-UO 2 Irradiation Test

Several destructive postirradiation examinations were performed on an irradiation specimen that coupled an early iron-chromium-aluminum (FeCrAl) candidate alloy cladding with UO2 pellets. This irradiation test was designed to investigate the early life performance and compatibility of the FeCrAl-UO 2 cladding-fuel system under prototypic light water reactor neutronic conditions. Additionally, these tests were expected to provide neutron irradiated samples for severe accident testing of this fuel system. The irradiation studied in this work was part of the ATF-1 series of drop-in style irradiations performed in the Idaho National Laboratory Advanced Test Reactor. The rodlet studied in this work is one of three similar rodlets irradiated in ATF-1 that had approximately 7.6 cm of cladding machined from a wrought FeCrAl alloy and fueled with a 6.1 cm stack of UO 2 pellets. The outer diameter of the cladding was ~0.94 cm and the inner diameter was ~0.83 cm. After irradiation and non-destructive examination in Idaho this rodlet was shipped to the Oak Ridge National Laboratory hot-cells for further examination. The irradiated rodlet was sectioned into several samples for microstructural, micromechanical, and severe accident testing. During sectioning, it was noted that the fuel was not firmly bonded to the cladding and could be readily removed from small cladding slices. Microstructural characterization of fuel cross sections also revealed no significant interaction between the fuel and the cladding. Samples were also prepared for microhardness testing. To prepare for high temperature oxidation testing, the fuel was dissolved from segments of the cladding. High temperature oxidation testing of cladding segments was performed at 1200°C and 1300°C in a steam environment. Comparisons between the oxidation of this FeCrAl alloy in its neutron irradiated state, as-fabricated state, and the oxidation of Zircaloy-2 are made. The oxidation testing will be followed by ring compression testing to evaluate ductility. The microstructure of the samples after oxidation and ring compression testing will also be analyzed.

Harp, Jason↗
DOE OSTI2023

Fuel performance evaluation of two high burnup PWR core designs during normal operation, control rod withdrawal, and control rod ejection scenarios

There is interest among utilities to extend the current, 18-month operating cycle to 24 months. Economically, this extension would require greater than 5 % enrichment and peak rod average discharge burnup levels above 62 GWd/MTU. A notable challenge of increasing enrichment is the resulting additional excess reactivity encountered during the early stages of fuel life. To accommodate, burnable absorbers beyond soluble boron are introduced into the fuel system. In high burnup fuels, the possibilities of cladding lift-off and fuel melting increase due, in part, to increased rod internal pressures and limited fuel thermal conductivity, respectively. This work collaboratively employs PARCS, RELAP5-3D, and BISON to compare the fuel performance of two high burnup fuel candidates with higher than 5 % enrichment. Here, the fuel performance parameters were compared to current NRC guidance. The results demonstrate an annular fuel design with homogenously blended gadolinium as a burnable absorber operates with greater safety margins during normal operation, allowing for additional operational flexibility. During normal operation, the core design utilizing Integral Fuel Burnable Absorber pins contained fuel pins which reached plenum pressures above 15.5 MPa by the end of the first fuel cycle and fuel pins experienced cladding hoop strains above 1 %. In the Gd core design, only two observed pins experienced plenum pressures above 15.5 MPa and no pins exceeded 1 % cladding hoop strain. During the control rod withdrawal scenario, plenum pressures for pins in both designs marginally exceeded system pressure, however neither experienced excessive hoop strain. The Gd core design experienced a maximum fuel temperature of 2418 K, which is significantly higher than the Integral Fuel Burnable Absorber design at 2157 K, but still within regulatory guidance. We predicted that the fuel in both could return to service after the CRW event. We also predicted that cladding would not fail during the Control Rod Ejection in either core design. Generally, the Integral Fuel Burnable Absorber core design performed with greater safety margin with regards to temperature during normal operation and the transient events. However, the Gd core design performed with greater safety margin regarding plenum pressure and hoop strain limits during normal operation and both transient events.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Development of Instrumented Advanced Test Reactor Irradiation Capsule Experiment for In-situ Thermal Conductivity Measurements of High-Density Fuels

Idaho National Laboratory (INL) is developing a first-of-a-kind leadout instrumented capsule experiment design to enable in-situ measurement capabilities in the Advanced Test Reactor (ATR) core. The Ceramic Advanced Thermal Evolution Research (CRATER) experiment supports the aLEU program objective to accelerate fuel performance irradiation testing for identifying alternative high-assay, low enriched uranium (HALEU) fuel systems. CRATER is a fueled, instrumented capsule experiment to measure in-situ temperature and thermal conductivity of ceramic fuels. Two ceramic fuel types will be used, uranium mono-nitride (UN) and uranium mono-carbide (UC), with a third metallic fuel used for comparison (UMo). The three fuel specimens will use a stainless-steel cladding. Programmatic objectives include linear heat generation rates (LHGR) of 210 ± 25 Watts per cm. and an inner clad temperature of 300-450 °C. The evolution of fuel thermal conductivity during irradiation has never been successfully measured in-situ for these systems and this experiment is designed to use advances in measurement sciences to characterize how thermal transport properties evolve while in reactor. Neutronic simulations of the experiment and its surrounding reactor environment were conducted using the Monte Carlo N-Particle Transport code (MCNP) and result in optimized fuel enrichment to meet target linear heat generation rates (LHGRs) influencing fuel temperatures, and fuel burnup requirements. Fabrication research and development (R&D) efforts are underway to produce annular right cylinder UC and UN pellets using carbothermic reduction and nitridation (or hydride-dehydride-nitride) synthesis methods, followed double-action die cold isostatic pressing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Transmission electron microscopy study of a high burnup U-10Zr metallic fuel

To support the development of U-10 wt.% Zr (U-10Zr) metallic fuel for Gen IV sodium-cooled fast reactors, we analysed a solid, Na-bonded, U-10Zr (by weight percent) fuel cross section that was irradiated to a burnup of ~ 12.4 % at.% at the Fast Flux Test Facility (FFTF). Advanced characterization techniques, including site specific sample preparation by focused ion beam (FIB) and phase/chemical determination by transmission electron microscopy (TEM), were used to reveal the constituent redistribution of Zr, characterize the fuel phases and the secondary phases (such as solid fission products) present at the end of life. It is shown that the fuel pin cross section is divided into three major concentric zones: a Zr-rich central region, a Zr-lean intermediate region, and a Zr intermediate peripherical region. The phase characterization revealed that the irradiation environment enhanced the development and stabilization of phases not predicted by the standard equilibrium U-Zr phase diagrams. Comparing the current results with the ones from previous studies, it is reaffirmed that the irradiation temperature and the time spent in the reactor, rather than the fuel burnup, are the two factors that most influence the formation of redistribution zones and their extension along the fuel cross section. Various solid fission products precipitated inside the fission gas pores, such as lanthanides, ZrRu, BaTe, CsI, and Ba and Sr oxides. Here, this study provides unprecedented nanoscale understandings in the U-10Zr fuel system that may benefit fuel performance modelling and advanced fuel development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Status of Eddy Current Developments at INL

Both standard and advanced Light Water Reactor (LWR) fuel systems are composed of fuel pellets enclosed in a metallic cladding. The fuel cladding represents the first containment of the fission products and the first safety barrier. Upon progression of irradiation, the cladding properties deteriorate, mainly due to the pick-up of hydrogen, which causes embrittlement, and the consequence corrosion that reduced the metallic substrate. Those changes in the properties combined with the harsh environment, e.g., fatigue and fretting occurring during operation, might eventually lead to loss of hermeticity. Therefore, it is important to be able to quantify the amount of corrosion taking place and to detect and size structural discontinuity that can promote cladding failure. Eddy current testing is one of the non-destructive methods employed for this purpose. Inspections are carried out using special probes, which are designed and optimized to inspect a tube with well-defined geometrical and physical characteristics, i.e. external diameter, wall thickness, material electric conductivity and magnetic permeability. The inspection goals are mainly twofold: first, the determination of the amount of corrosion by measurement of the external oxide thickness; second, the detection of flaws in the tube wall, ether on the external or the internal surface of the tube. This report summarizes the available capabilities for eddy current testing of LWR fuel claddings, identifies needs and are of developments for testing of ATF claddings.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

The Jupiter High-240 Experiment

The Jupiter High-240 experiment was performed in May of 2019 by researchers from Los Alamos National Laboratory (LANL) at the National Criticality Experiments Research Center (NCERC) in the Device Assembly Facility (DAF) located at the Nevada National Security Site (NNSS). This experiment has previously been mentioned briefly in prior publication related to a collaborative effort with the Japan Atomic Energy Agency (JAEA) to assess lead void coefficients of reactivity in uranium- and plutonium-fueled systems with lead. This series of experiments supports JAEA’s research into the development of an accelerator driven transmutation system for spent nuclear fuel. The Jupiter High-240 experiment built upon the previous Jupiter experiment by incorporating plutonium fuel plates with higher 240 Pu content. Efforts to formally benchmark the original Jupiter experiment have continued for inclusion in the benchmark handbook of the International Criticality Safety Benchmark Evaluation Project (ICSBEP). Whereas there is much similarity between the two Jupiter experiments, there is a desire to also evaluate and benchmark this second experiment to further contribute towards the availability of lead-sensitive benchmarks. The components utilized in these two experiments have also been used to perform other subcritical and Rossi-α measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Methods and systems for a fuel injector

Methods and systems are provided for a ducted fuel injector. In one example, a method may include adjusting a temperature of combustion chamber gases in a combustion chamber and/or adjusting a fuel rail pressure in response to an amount of light sensed by a photodiode of the duct.

02 PETROLEUM↗
DOE OSTI2021

System and method for consolidating used nuclear fuel

A system and method for consolidating used nuclear fuel rods using tools operably suspendable in a recess containing the used nuclear fuel rods. The systems and methods safely consolidate the used nuclear fuel rods in containers.

Rose, Scott E.↗
DOE OSTI2022

Overview of Base Model in Parametric Studies Specific to Performance of U-Mo Plates

This paper provides an overview of the base model specifically developed to perform parametric sensitivity studies on the U-10Mo monolithic fuel system. U-Mo monolithic fuels are being considered for the conversion of test reactors into high-performance research reactors that operate using proliferation-resistant, low-enriched uranium (LEU) fuels. These plate-type fuels contain a high-density, low-enrichment fuel sandwiched between zirconium diffusion barriers and encapsulated in aluminum claddings. All U.S. high-performance research reactors have released the designs of their LEU monolithic fuel reactor cores. These designs include nearly 50 distinct fuel plate geometries with different operational parameters. Consequently, a single generic plate geometry representing all the extreme points in this design matrix is unrealistic. To evaluate the performance for various parameters, a set of sensitivity studies was performed. These studies considered various input parameters (i.e., geometric, operational, and material property-related). The results revealed valuable information about plate performance and the sensitivity of this performance to various modeling inputs. To establish a reference state for comparing these result, base model featuring representative irradiation conditions was developed. To capture in-reactor behavior accurately, incorporation of representative constitutive models capable of evolving properties with respect to temperature, irradiation time, and burnup was needed. The behavioral models considered burnup-dependent properties, swelling, creep, and degradation. This paper introduces the base model created for the parametric sensitivity studies. The detailed description of the procedure includes the model geometry, model discretization, thermo-mechanical coupling, material properties and behavioral models. This paper also provides selected results and assesses the performance of the base model.

42 ENGINEERING↗
DOE OSTI2021

Global Ethanol-Blended-Fuel Vehicle Compatibility Study

The objective of this study is to understand the impact of ethanol-blended fuel at various blending levels (10%, 15%, and 20% vol.) on "in-operation" vehicles built to differing emissions and manufacturing standards around the world. The study focuses on vehicles used in Canada, China, India, Indonesia, Japan, South Korea, and Mexico. Historical experience in the United States and Brazil informs the analysis. The primary study question is: Are vehicles in targeted countries physically and operationally compatible with ethanol blended fuel? For a fuel to be compatible with a vehicle, the fuel must perform its function as part of the integrated fuel-vehicle system, meaning: the car should start easily and drive normally, the fuel should not cause catastrophic fuel system leaks, the fuel should not cause corrosion or degradation of any engine or fuel system components (including emissions control components). The history of E10 use in the United States, beginning in 1978, was evaluated and shows no reliability or operability issues for cars dating back to pre-emissions-control times -- and likely included many cars manufactured in the 1960s. This strongly supports the contention that fuel chemistry and property differences between E0 and E10 are so small that any car made to international standards in the last 50 years will have a very high probability of being fully compatible with E10. This conclusion is supported by the experience in Brazil in the 1970s, where E10 was also introduced, and ethanol blending for conventional cars rapidly ramped up to even higher blend levels. A limited number of fuel system and component manufacturers supply the global market, including Bosch, Continental, Denso, Delphi, and Visteon. To reduce complexity, ethanol-compatible materials began to be integrated in fuel system designs globally. Fuel systems evolved over the following decades to incorporate ethanol-compatible materials with core subsystem families, such as in-tank fuel pumps used across several global vehicle original equipment manufacturers (OEMs). A similarly compelling case can be made that all cars at the Tier 1 (or equivalent) emissions-control technology level or higher are fully compatible with E15 blends, based on the data evaluated by the U.S. Environmental Protection Agency (EPA) and Ricardo in 2010. For cars at this technology level, the minor differences in fuel chemistry and properties between E10 and E15 are not significant. For E20, studies are not as extensive but are still highly significant. A long-term durability study conducted on mileage accumulation dynamometers presents convincing evidence that Tier 2 technology level cars have materials of construction and engine control authority for compatibility with E20, although this conclusion is not as strong as those drawn for E10 and E15, which are also partly based on real-world experience.

09 BIOMASS FUELS↗