Search NASA⌕ Search

SEARCH · Search NASA

Results for “Feedforward control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Beam-Waveguide Antenna Servo Design Issues for Tracking Low-Earth-Orbiting Satellites

The upcoming NASA missions will require tracking of low-orbit satellites. As a consequence, NASA antennas will be required to track satellites at higher rates than for the current deep space missions. This paper investigates servo design issues for the 34-m beam-waveguide (BWG) antennas that track low-orbit satellites. This includes the upgrade of the servo with the feedforward loop, monopulse controller design, and tracking error reduction through proper choice of elevation pinion location, through application of a notch filter, and through the elevation drive amplifier gain adjustment. Finally, improvement of the signal-to-noise ratio through averaging of the oversampled monopulse signal is presented.

Mellstrom, J. A.↗
NASA NTRS1991

Towards practical control design using neural computation

The objective is to develop neural network based control design techniques which address the issue of performance/control effort tradeoff. Additionally, the control design needs to address the important issue if achieving adequate performance in the presence of actuator nonlinearities such as position and rate limits. These issues are discussed using the example of aircraft flight control. Given a set of pilot input commands, a feedforward net is trained to control the vehicle within the constraints imposed by the actuators. This is achieved by minimizing an objective function which is the sum of the tracking errors, control input rates and control input deflections. A tradeoff between tracking performance and control smoothness is obtained by varying, adaptively, the weights of the objective function. The neurocontroller performance is evaluated in the presence of actuator dynamics using a simulation of the vehicle. Appropriate selection of the different weights in the objective function resulted in the good tracking of the pilot commands and smooth neurocontrol. An extension of the neurocontroller design approach is proposed to enhance its practicality.

Troudet, Terry↗
NASA NTRS1987

Linear quadratic stationkeeping on travelling ellipses

An automatic controller for Space Shuttle stationkeeping or formationkeeping is presented. The controller, which is a candidate for future on-orbit autopilot enhancement, uses a fuel 'optimized' limit cycle trajectory in a feedforward loop for precise control at nonequilibrium set points. Disturbance rejection is accomplished by a discrete time, linear quadratic regulator, which is employed for tracking of the feedforward model. Feedback gain selection is done to provide good limit cycling performance and low fuel consumption. Velocity correlations are carried out by use of a pseudo 6 degree-of-freedom jet selection scheme. Results indicate that 20 ft precision can be achieved using current sensors.

Adams, Neil J.↗
NASA NTRS1998

Input Shaping to Reduce Solar Array Structural Vibrations

Structural vibrations induced by actuators can be minimized using input shaping. Input shaping is a feedforward method in which actuator commands are convolved with shaping functions to yield a shaped set of commands. These commands are designed to perform the maneuver while minimizing the residual structural vibration. In this report, input shaping is extended to stepper motor actuators. As a demonstration, an input-shaping technique based on pole-zero cancellation was used to modify the Solar Array Drive Assembly (SADA) actuator commands for the Lewis satellite. A series of impulses were calculated as the ideal SADA output for vibration control. These impulses were then discretized for use by the SADA stepper motor actuator and simulated actuator outputs were used to calculate the structural response. The effectiveness of input shaping is limited by the accuracy of the knowledge of the modal frequencies. Assuming perfect knowledge resulted in significant vibration reduction. Errors of 10% in the modal frequencies caused notably higher levels of vibration. Controller robustness was improved by incorporating additional zeros in the shaping function. The additional zeros did not require increased performance from the actuator. Despite the identification errors, the resulting feedforward controller reduced residual vibrations to the level of the exactly modeled input shaper and well below the baseline cases. These results could be easily applied to many other vibration-sensitive applications involving stepper motor actuators.

Doherty, Michael J.↗
NASA NTRS2005

Small Body GN&C Research Report: A Robust Model Predictive Control Algorithm with Guaranteed Resolvability

A robustly stabilizing MPC (model predictive control) algorithm for uncertain nonlinear systems is developed that guarantees the resolvability of the associated finite-horizon optimal control problem in a receding-horizon implementation. The control consists of two components; (i) feedforward, and (ii) feedback part. Feed-forward control is obtained by online solution of a finite-horizon optimal control problem for the nominal system dynamics. The feedback control policy is designed off-line based on a bound on the uncertainty in the system model. The entire controller is shown to be robustly stabilizing with a region of attraction composed of initial states for which the finite-horizon optimal control problem is feasible. The controller design for this algorithm is demonstrated on a class of systems with uncertain nonlinear terms that have norm-bounded derivatives, and derivatives in polytopes. An illustrative numerical example is also provided.

model predictive control algorithm (MPC)↗
NASA NTRS1979

Gust alleviation using direct turbulence measurements

The research reported upon in this paper describes an effective method of gust alleviation using direct measurements of atmospheric turbulence to drive the aircraft control surfaces in a way that attempts to directly counter or cancel those forces and moments produced on the aircraft by gusts. The method yields a feedforward or open loop control law, simple to mechanize and relatively insensitive to changes in flight condition. When applied directly, the resulting control law effectively gust-alleviates in the low frequency phugoid and short period range but has a tendency to amplify structural mode vehicle motions due to the phase lag of the actuators. A method of design based upon the use of a diagonal or Jordan form of the equations of motion enables the designer to avoid this problem of structural mode excitation.

Rynaski, E. G.↗
NASA NTRS1993

Active control of fan noise from a turbofan engine

A three channel active control system is applied to an operational turbofan engine in order to reduce tonal noise produced by both the fan and high pressure compressor. The control approach is the feedforward filtered-x least-mean-square algorithm implemented on a digital signal processing board. Reference transducers mounted on the engine case provides blade passing and harmonics frequency information to the controller. Error information is provided by large area microphones placed in the acoustic far field. In order to minimize the error signal, the controller actuates loudspeakers mounted on the inlet to produce destructive interference. The sound pressure level of the fundamental tone of the fan was reduced using the three channel controller by up to 16 dB over a 60 deg angle about the engine axis. A single channel controller could produce reduction over a 30 deg angle. The experimental results show the control to be robust. Simultaneous control of two tones is done with parallel controllers. The fundamental and the first harmonic tones of the fan were controlled simultaneously with reductions of 12 dBA and 5 dBA, respectively, measured on the engine axis. Simultaneous control was also demonstrated for the fan fundamental and the high pressure compressor fundamental tones.

Thomas, Russell H.↗
NASA NTRS1994

Active control of fan noise from a turbofan engine

A three-channel active control system is applied to an operational turbofan engine to reduce tonal noise produced by both the fan and the high-pressure compressor. The control approach is the feedforward filtered-x least-mean-square algorithm implemented on a digital signal processing board. Reference transducers mounted on the engine case provide blade passing and harmonics frequency information to the controller. Error information is provided by large area microphones placed in the acoustic far field. To minimize the error signal, the controller actuates loudspeakers mounted on the inlet to produce destructive interference. The sound pressure level of the fundamental tone of the fan was reduced using the three-channel controller by up to 16 dB over a +/- 30-deg angle about the engine axis. A single-channel controller could produce reduction over a +/- 15-deg angle. The experimental results show the control to be robust. Outside of the areas contolled, the levels of the tone actually increased due to the generation of radial modes by the control sources. Simultaneous control of two tones is achieved with parallel controllers. The fundamental and the first harmonic tones of the fan were controlled simultaneously with reductions of 12 and 5 dBA, respectively, measured on the engine axis. Simultaneous control was also demonstrated for the fan fundamental and the high-pressure compressor fundamental tones.

Thomas, Russell H.↗
NASA NTRS2012

Analysis of Control Strategies for Aircraft Flight Upset Recovery

This paper proposes a framework for studying the ability of a control strategy, consisting of a control law and a command law, to recover an aircraft from ight conditions that may extend beyond the normal ight envelope. This study was carried out (i) by evaluating time responses of particular ight upsets, (ii) by evaluating local stability over an equilibrium manifold that included stall, and (iii) by bounding the set in the state space from where the vehicle can be safely own to wings-level ight. These states comprise what will be called the safely recoverable ight envelope (SRFE), which is a set containing the aircraft states from where a control strategy can safely stabilize the aircraft. By safe recovery it is implied that the tran- sient response stays between prescribed limits before converging to a steady horizontal ight. The calculation of the SRFE bounds yields the worst-case initial state corresponding to each control strategy. This information is used to compare alternative recovery strategies, determine their strengths and limitations, and identify the most e ective strategy. In regard to the control law, the authors developed feedback feedforward laws based on the gain scheduling of multivariable controllers. In regard to the command law, which is the mechanism governing the exogenous signals driving the feed- forward component of the controller, we developed laws with a feedback structure that combines local stability and transient response considera- tions. The upset recovery of the Generic Transport Model, a sub-scale twin-engine jet vehicle developed by NASA Langley Research Center, is used as a case study.

Crespo, Luis G.↗
NASA NTRS1991

Implementation of a three degree of freedom, motor/brake hybrid force output device for virtual environment control tasks

The advent of high resolution, physical model based computer graphics has left a gap in the design of input/output technology appropriate for interacting with such complex virtual world models. Since virtual worlds consist of physical models, it is appropriate to output the inherent force information necessary for the simulation to the user. The detailed design, construction, and control of a three degree freedom force output joystick will be presented. A novel kinematic design allows all three axes to be uncoupled, so that the system inertia matrix is diagonal. The two planar axes are actuated through an offset gimbal, and the third through a sleeved cable. To compensate for friction and inertia effects, this transmission is controlled by a force feedforward and a closed force feedback proportional loop. Workspace volume is a cone of 512 cubic inches, and the device bandwidth is maximized at 60 Hz for the two planar and 30 Hz for the third axis. Each axis is controlled by a motor/proportional magnetic particle brake combination fixed to the base. The innovative use of motors and brakes allows objects with high resistive torque requirements to be simulated without the stability and related safety issues involved with high torque, energy storing motors alone. Position, velocity, and applied endpoint force are sensed directly. Different control strategies are discussed and implemented, with an emphasis on how virtual environment force information, generated by the MIT Media Lab Computer Graphics and Animation Group BOLIO system, is transmitted to the device controller. The design constraints for a kinesthetic force feedback device can be summarized as: How can the symbiosis between the sense of presence in the virtual environment be maximized without compromising the interaction task under the constraints of the mechanical device limitations? Research in this field will yield insights to the optimal human sensory feedback mix for a wide spectrum of control and interaction problems. A flexible research tool that is designed as an easily reproducible product prototype has been constructed to explore the variety of possible force interaction.

Russo, Massimo↗
NASA NTRS1976

Digital adaptive control of a VTOL aircraft

A technique has been developed for calculating feedback and feedforward gain matrices that stabilize a VTOL aircraft while enabling it to track input commands of forward and vertical velocity. Leverrier's algorithm is used in a procedure for determining a set of state variable, feedback gains that force the closed loop poles and zeroes of one pilot input transfer function to be at preselected positions in the s plane. This set of feedback gains is then used to calculate the feedback and feedforward gains for the velocity command controller. The method is computationally attractive since the gains are determined by solving systems of linear, simultaneous equations. Responses obtained using a digital simulation of the longitudinal dynamics of the CH-47 helicopter are presented.

Reid, G. F.↗
NASA NTRS1990

Neural networks for function approximation in nonlinear control

Two neural network architectures are compared with a classical spline interpolation technique for the approximation of functions useful in a nonlinear control system. A standard back-propagation feedforward neural network and a cerebellar model articulation controller (CMAC) neural network are presented, and their results are compared with a B-spline interpolation procedure that is updated using recursive least-squares parameter identification. Each method is able to accurately represent a one-dimensional test function. Tradeoffs between size requirements, speed of operation, and speed of learning indicate that neural networks may be practical for identification and adaptation in a nonlinear control environment.

Linse, Dennis J.↗
NASA NTRS1999

Active Control of Inlet Noise on the JT15D Turbofan Engine

This report presents the key results obtained by the Vibration and Acoustics Laboratories at Virginia Tech over the year from November 1997 to December 1998 on the Active Noise Control of Turbofan Engines research project funded by NASA Langley Research Center. The concept of implementing active noise control techniques with fuselage-mounted error sensors is investigated both analytically and experimentally. The analytical part of the project involves the continued development of an advanced modeling technique to provide prediction and design guidelines for application of active noise control techniques to large, realistic high bypass engines of the type on which active control methods are expected to be applied. Results from the advanced analytical model are presented that show the effectiveness of the control strategies, and the analytical results presented for fuselage error sensors show good agreement with the experimentally observed results and provide additional insight into the control phenomena. Additional analytical results are presented for active noise control used in conjunction with a wavenumber sensing technique. The experimental work is carried out on a running JT15D turbofan jet engine in a test stand at Virginia Tech. The control strategy used in these tests was the feedforward Filtered-X LMS algorithm. The control inputs were supplied by single and multiple circumferential arrays of acoustic sources equipped with neodymium iron cobalt magnets mounted upstream of the fan. The reference signal was obtained from an inlet mounted eddy current probe. The error signals were obtained from a number of pressure transducers flush-mounted in a simulated fuselage section mounted in the engine test cell. The active control methods are investigated when implemented with the control sources embedded within the acoustically absorptive material on a passively-lined inlet. The experimental results show that the combination of active control techniques with fuselage-mounted error sensors and passive control techniques is an effective means of reducing radiated noise from turbofan engines. Strategic selection of the location of the error transducers is shown to be effective for reducing the radiation towards particular directions in the farfield. An analytical model is used to predict the behavior of the control system and to guide the experimental design configurations, and the analytical results presented show good agreement with the experimentally observed results.

Smith, Jerome P.↗
NASA NTRS1989

Interface For Fault-Tolerant Control System

Interface unit and controller emulator developed for research on electronic helicopter-flight-control systems equipped with artificial intelligence. Interface unit interrupt-driven system designed to link microprocessor-based, quadruply-redundant, asynchronous, ultra-reliable, fault-tolerant control system (controller) with electronic servocontrol unit that controls set of hydraulic actuators. Receives digital feedforward messages from, and transmits digital feedback messages to, controller through differential signal lines or fiber-optic cables (thus far only differential signal lines have been used). Analog signals transmitted to and from servocontrol unit via coaxial cables.

Shaver, Charles↗
NASA NTRS1976

A velocity-command controller for a VTOL aircraft

A technique is presented for calculating feedback and feedforward gain matrices that enable a VTOL aircraft to track input commands of forward and vertical velocity while maintaining acceptable responses to pilot inputs. Leverrier's algorithm is used for determining a set of state-variable, feedback gains that force the closed-loop poles and zeros of one pilot-input transfer function to pre-selected positions in the s-plane. This set of feedback gains is then used to calculate the feedback and feedforward gains for the velocity-command controller. The method is computationally attractive since the gains are determined by solving systems of linear, simultaneous equations. The method is used in a digital simulation of the CH-47 helicopter to control longitudinal dynamics.

Reid, G. F.↗
NASA NTRS1976

A velocity-command controller for a VTOL aircraft

A technique is presented for calculating feedback and feedforward gain matrices that enable a VTOL aircraft to track input commands of forward and vertical velocity while maintaining acceptable responses to pilot inputs. Leverrier's algorithm is used for determining a set of state-variable, feedback gains that force the closed-loop poles and zeros of one pilot-input transfer function to pre-selected positions in the s-plane. This set of feedback gains is then used to calculate the feedback and feedforward gains for the velocity-command controller. The method is computationally attractive since the gains are determined by solving systems of linear, simultaneous equations. The method has been used in a digital simulation of the CH-47 helicopter to control longitudinal dynamics.

Reid, G. F.↗
NASA NTRS1976

A moving-window parameter adaptive control system for the F8-DFBW aircraft

This paper describes the moving-window parameter adaptive control system developed for the NASA F8-DFBW aircraft. The control system employs a parameter identification process that, iteratively, adjusts parameters of a model of the aircraft motions in a batch processing manner so that responses generated from the model fit the outputs of sensors stored in a finite record referred to as the moving window. Tests are made on the validity of the parameter estimates before using the parameters in an on-line design process. The on-line design process is an algebraic mapping of the parameters of the model into primary control system feedback and feedforward gains. The mapping was selected to satisfy specific flying quality characteristics over the range of parameter variations expected. Results are presented from simulation studies on the identification algorithm, tests for parameter validity, and the on-line design process.

Montgomery, R. C.↗
NASA NTRS1977

A moving window parameter adaptive control system for the F8-DFBW aircraft

This paper describes the moving window parameter adaptive control system developed for the NASA F8-DFBW aircraft. The control system employs a parameter identification process that, iteratively, adjusts parameters of a model of the aircraft motions in a batch-processing manner so that responses generated from the model fit the outputs of sensors stored in a finite record referred to as the moving window. Tests are made on the validity of the parameter estimates before using the parameters in an on-line design process. The on-line design process is an algebraic mapping of the parameters of the model into primary control system feedback and feedforward gains. The mapping was selected to satisfy specific flying quality characteristics over the range of parameter variations expected. Results are presented from simulation studies on the identification algorithm made during the development of the system.

Dunn, H. J.↗