Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flexural testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Tribological behavior of spark plasma sintered Ti 3 SiC 2 MAX phase composites

Ti₃SiC₂ MAX phases are considered promising candidates for tribological applications; but, their low hardness (5-6 GPa) can lead to increased abrasive wear and higher wear rates. This study investigates the effect of incorporating hard SiC particles on microstructure, mechanical, and tribological behavior of Ti₃SiC₂-SiC-based MAX phase composites prepared using spark plasma sintering at 1400 °C, 40 MPa, 15-minute holding time. Phase and microstructural characterization of composites confirmed the formation of Ti₃SiC₂ MAX phase (90%) along with TiC as a minor phase (10%). For Ti₃SiC₂-SiC, homogeneous distribution of SiC grains within Ti₃SiC₂ matrix resulted in increased hardness from ~11.6 GPa to ~14.8 GPa; however, the flexural strength decreased from ~615 MPa to ~597 MPa due to coefficient of thermal expansion mismatch. Tribological behavior of Ti₃SiC₂-SiC MAX phase composites was assessed using unidirectional sliding ball-on-flat tests with a 52100 steel ball at different loads and a constant speed of 0.05 m/s. SiC reinforced composites exhibited a decreased friction coefficient from 0.39 to 0.29 and wear rates comparable to Ti₃SiC₂ (7-10×10⁻³ mm³/N·m). SEM and EDS analysis of the worn surfaces indicated material transfer from the steel ball counter body and its oxidation due to frictional heating, at lower loads (2N and 5N), whereas at higher load (10N), fracture of the transfer layer dominated, with the presence of microcracks, delamination, grain pull-outs, and wear debris. Improved mechanical properties and good adhesion of SiC with Ti₃SiC₂ matrix resulted in reduced microcracks and grain pull-outs, making Ti₃SiC₂-SiC/Steel tribo-pair more suitable for tribological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Simulated lightning strike investigation of CFRP comprising a novel Polyaniline/Phenol based electrically conductive resin matrix

Traditional carbon fiber reinforced plastics (CFRPs) have been reported to exhibit lower electrical conductivity in the through-thickness direction, and have since paved the path for developing new resin systems to improve the through-thickness electrical conductivity and functionality of CFRP laminates. This work designs and investigates a novel Polyaniline (PANI)/Phenol resin, which possesses high electrical conductivity and mechanical strength. The CFRP manufactured by this PANI/Phenol resin with an addition of up to (~23.30%) phenol resulted in 0.6 S/cm through-thickness conductivity and demonstrated flexural strength and modulus values of 477 MPa and 59.2 GPa, respectively. We further evaluate the effectiveness of lightning strike protection of PANI/Phenol-based conductive CFRP laminates with a simulated lightning strike test. In essence, this research reports on PANI/Phenol-based CFRP's effectiveness as a material for lightning suppression without applying traditional metal-based lightning strike protection (LSP) systems.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Aging of Limestones and Silane–Siloxane-Based Protective Hydrophobics: The Impact of Heating–Cooling and Freeze–Thaw Cycles

Stones are traditionally used in construction and architectural applications as building elements due to their aesthetic and technical/structural performance. Like other environmental factors (rain, humidity, moisture, salt presence, biological activity, etc.), heating–cooling and freeze–thaw cycles significantly threaten the longevity of stone materials. Hence, considering the socio-economic and cultural value of stones, preventive actions such as hydrophobic coatings are applied to prevent or mitigate damage. The scope of this study is the performance assessment of limestones with different characteristics and the efficiency of various commercial silane/siloxane-based hydrophobic coatings when exposed to thermal variation and freeze–thaw. For that purpose, the standards EN 14066:2013 (determination of resistance to aging by thermal shock) and EN 12371:2010 (determination of frost resistance) were followed. Open porosity and static contact angles were estimated to assess the stone durability and water protection capabilities of the hydrophobics. Additionally, sound speed propagation velocity, quality of building material index, elastic modulus and flexural strength were measured to evaluate the variation of mechanical properties. Static contact angle revealed that the coatings maintained an efficient level of hydrophobicity even after thermal-shock and freeze–thaw weathering tests. The study also revealed a critical interaction between freeze–thaw cycles, hydrophobic coatings and structural integrity of the stones, mostly on more porous ones. When they are subjected to harsh environmental conditions, untreated porous limestones keep structural cohesion, allowing for the natural absorption and release of water during freezing and thawing. On the contrary, when limestones are treated, the hydrophobic coatings can moderately obstruct the water release due to the partial saturation of the porous framework by the products. It also probably resulted from the different mechanical behavior between the inner matrix and layer of stone coated, resulting in a premature breakout and mechanical damage of the stone.

Lisci, Carla (ORCID:000000032179130X)↗
DOE OSTI2024

MOLLER Spectrometer Magnet Design With Measured Mechanical Properties of Irradiated S2-Glass Reinforced Cyanate Ester Resin at Elevated Temperature

Here, the aim of this study was to retire the risk of maintaining the integrity of S2-glass reinforced CTD-403 (a cyanate ester resin) that is exposed to radiation and elevated temperature over the life of the measurement of a lepton–lepton electroweak reaction (MOLLER) experiment in experimental Hall A at Jefferson Lab, Newport News, VA. In this article, the shear strength and flexural modulus of irradiated S2-glass reinforced CTD-403 specimens were measured at 65 °C (the magnets are to operate at less than 65 °C) under two scenarios: vacuum and gaseous nitrogen. The testing method is the short-beam shear (SBS) test according to ASTM D2344. The specimens were exposed to neutrons and gamma rays up to 124 MGy. The results show that specimens have excellent resistance against radiation, only 23% degradation of apparent shear strength with 124 MGy at 65 °C under vacuum. At the highest dose areas of the coils, tungsten plates are used to reduce the radiation dose to the resin system. The conclusion is that S2-glass reinforced CTD-403 is well-suited for electrical insulation of MOLLER magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Carbon Fiber and Syntactic Foam Hybrid Materials via Core–Shell Material Extrusion Additive Manufacturing

Abstract Biological materials often employ hybrid architectures, such as the core–shell (C–S) motif present in porcupine quills and plant stems, to achieve unique specific properties and performance. Drawing inspiration from these natural materials, a new method to fabricate lightweight and stiff C–S architected filaments is reported. Specifically, a C–S printhead conducive to printing highly loaded fiber‐filled inks, as well as a new low‐density syntactic foam ink, are utilized to 3D‐print C–S architectures consisting of a syntactic epoxy foam core surrounded by a stiff carbon fiber‐reinforced epoxy composite shell. Effective printing of test specimens and structures with controlled geometry, composition, and architecture is demonstrated. The new foam ink exhibits density as low as 0.68 g cm −3 and C–S structures exhibit up to 25% higher specific flexural stiffness ( E 1/3 /ρ) than either constituent alone. Finally, a new mechanical model is presented to predict this performance improvement while accounting for potential eccentricity of the core.

Pack, Robert C.↗
DOE OSTI2024

Sister Rod Destructive Examinations (FY23): Appendix H: Instron Uncertainty Calculations

This document discusses the uncertainty of measurements associated with the Instron system and the resulting uncertainty in the acquired measurements and calculated information. The primary parameters measured during the Instron test include the applied load and specimen deflection. The associated primary calculated parameters are the maximum beam deflection at the rod’s axial center and modulus of elasticity. Secondary calculated parameters include specimen stress and strain amplitudes, as well as flexural rigidity. The uncertainty associated with the primary and secondary calculated parameters was investigated based on the known uncertainty in the measured parameters.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Multiscale Porous High-temperature Heat Exchanger Using Ceramic Co-extrusion

In this project, our MIT, Purdue, and GE team aims to design, model, fabricate, and test a novel high temperature, compact, and durable ceramic heat exchanger to be operated under high temperature and pressure conditions for aerospace applications. Our approach is grounded in introducing multiscale porosity, i.e., centimeter-scale channels embedded with micrometer-scale channels, into the ceramic heat exchanger to significantly improve its heat transfer performance and mechanical strength while maintaining minimal pressure losses. We first developed high-fidelity thermal-fluid-mechanical model capable of precisely capturing the heat transfer rate, temperature profile, pressure drop, and mechanical stress throughout the entire heat exchanger design. Guided by our model, we identified the optimal design parameters for the SiC heat exchanger body and manifolds. Then, we established a completed fabrication procedure to create multiscale features in the ceramic heat exchanger, including co-extrusion, lamination, burnout, and sintering. We fabricated multiple heat exchanger bodies consisting of 6 × 6 and 3 × 3 centimeter-scale channels where each individual centimeter-scale channel comprises 625 crack-free microchannels with 90 μm × 90 μm opening. Owing to the multiscale features, our fabricated heat exchanger bodies exhibited desirable mechanical strength with 156 MPa flexural strength under 1300 Celsius degree. Despite the demonstrated highly tailorable microscopic features and superior mechanical strength, we identified delamination due to the complex interaction among ceramic, polymer, and gas species can be a critical challenge to create fully defect-free heat exchanger, which requires further fundamental investigations in future works. To test the heat exchanger performance, we constructed a high-temperature and high-pressure experimental apparatus that can be safely operated under 400 Celsius degree and 4 bar. With insights gained from mechanistic modeling, material development, and detailed characterization, a cost model was finally developed to understand the market potential of the developed technology, where a cost of $43,000 Celsius degree/kW was envisioned. This project developed a transformative approach to high-performance heat exchanger design. The thermal-fluid-mechanical design approach developed in this project can serve as a generic tool to guide the design of various heat-exchangers operated under high-temperature and high-pressure conditions. The material fabrication approach established in this project can be a useful guide for ceramic processing at extreme length scales.

42 ENGINEERING↗
DOE OSTI2024

Dissimilar Material Joining via Interlocking Metasurfaces

Background The integration of dissimilar materials poses a significant challenge in engineering, necessitating innovative solutions for robust and reliable joining. Interlocking metasurfaces (ILMs) are a new joining technology comprising arrays of autogenous features patterned across two surfaces that interlock to form robust structural joints. Objective Here, this study elucidates the factors influencing the tensile performance of ILM joints formed between dissimilar materials. Methods We employed parametric optimization to identify optimal unit cell geometries for maximal yield strength based on the hypothesis that the elastic tensile properties of the materials are the primary determinants of tensile performance. Experimental validation was performed by mechanically testing the theorized optimal ILM geometry and a range of ILM geometries to capture the overall behavior trends of joints between two additively manufactured polymers, VeroPureWhite (VW) and RGDA8430-DM (8430). Results Experimental validation of optimized designs revealed that additional factors, e.g. flexural strength and localized plasticity, also strongly influenced the tensile performance of T-slot ILMs joining dissimilar materials. The proposed optimal design remained the best performer. Conclusions This study demonstrates the viability of ILMs as a joining method for dissimilar materials. ILMs can join dissimilar materials with no loss in joint yield strength compared to joints composed solely of the weaker of the two constitutive materials. ILMs demonstrated their potential as a versatile and effective joining technology in diverse engineering applications.

Elbrecht, Benjamin James [Sandia National Laborato↗
DOE OSTI2025

Environmentally Friendly Use of Carbon Ore for Advanced Building Materials for Homes and Commercial Buildings

Through this effort, X-MAT CCC sought to confirm the utility and commercialization potential of carbon-derived building materials (CDBM) technology licensed from our partner, Semplastics. These CDBM products contain at least 52% coal-derived carbon by mass. Including the binders within the resin, the products contain at least 71% carbon by mass overall, meeting a key criterion for DE-FOA-0002185 – Area of Interest (AOI) 5 – Design Research and Development, Validation, and Fabrication of a Prototype Carbon-Based Building. The Phase II project has resulted in a technology demonstrator prototype structure, a detailed design for a carbon-based building, and updated techno-economic analysis (TEA) including detailed market surveys to show the commercial viability of CDBM products. We pursued the following objectives in Phase II: (1) construction of a partial building shell as a technology demonstrator, (2) testing of CDBM products, individually and in assemblies, (3) demonstration of bonding of CDBM and traditional building materials (TBM) in structural applications, (4) production of a detailed design for a carbon-based building, and (5) an update of the TEA that was performed in Phase I. In Phase II, X-MAT CCC and our industry team performed the development and testing needed to improve the maturity of the technology from a Technology Readiness Level (TRL) of 5 to TRL 6. CDBM have been shown by our partner Semplastics to exhibit a number of high-performance characteristics, including high strength (five times the flexure strength of the best commercial brick, and more than twice the compressive strength of construction-grade concrete block), lower density, improved mechanical durability and abrasion resistance, very high temperature stability, and resistance to chemicals, acids, salts, and water. These properties offer significant improvements over conventional building materials. Phase II built upon the work accomplished in Phase I by performing technical and economic research and development to confirm the viability of CDBM as commercial products in various markets. Acknowledgment: This material is based upon work supported by the Department of Energy under Award Number DE-FE0031985.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Relationship between microstructure evolution and properties enhancement of carbon nanotubes‐filled polybutylene terephthalate/polypropylene blends induced by thermal annealing

Abstract Thermal annealing induced microstructure evolution and properties enhancement of polybutylene terephthalate/polypropylene/carbon nanotubes (PBT/PP/CNTs) nanocomposites was methodically investigated. The electrical conductive PBT/PP/CNTs nanocomposites with a low percolation threshold were obtained by simple melt blending due to the selective location of the CNTs in PBT phase and the formation of the double percolation structure. Thermal annealing further remarkably decreased the volume resistivity of the nanocomposites, with the maximum reduction of seven orders of magnitude. Scanning electron microscope observation and rheology tests demonstrated that the relatively large CNTs agglomerates were redistributed to build more homogeneous CNTs networks after annealing. The phase coalescence during annealing promoted the formation of the more perfect co‐continuous structure. These phenomena helped to enhance the electrical conductivity of the nanocomposites. Flexural properties of the nanocomposites were also enhanced after annealing, which might be due to the more effective stress transfer between the polymer and CNTs induced by the reconstructed CNTs networks. The nanocomposites obtained in this study possess excellent electrical and mechanical properties, which can be applied to the fields of sensors, electromagnetic interference shielding, anti‐static materials, and so forth.

Shang, Mengyao↗
DOE OSTI2022

Sister Rod Destructive Examinations (FY2021) Appendix G: CRIFT Uncertainty Calculations

This document discusses the uncertainty of measurements associated with the CIRFT system and the resulting uncertainty in the acquired measurements and calculated information. The primary parameters measured during the CIRFT test include the deflection magnitude of the specimen, the load applied in bending, and the number of cycles to specimen gross failure. The associated primary calculated parameters are the bending radius/curvature and bending moment. Secondary calculated parameters include specimen stress and strain amplitudes and flexural rigidity. The uncertainty associated with the primary and secondary calculated parameters are investigated based on the known uncertainty in the measured parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Sister Rod Destructive Examinations (FY23) Appendix G: CIRFT Uncertainty Calculations

This document discusses the uncertainty of measurements associated with the cyclic integrated reversible-bending fatigue tester (CIRFT) system and the resulting uncertainty in the acquired measurements and calculated information. The primary parameters measured during the CIRFT test include the deflection magnitude of the specimen, the load applied during bending, and the number of cycles to specimen gross failure. The associated primary calculated parameters are the bending radius/curvature and the bending moment. Secondary calculated parameters include specimen stress and strain amplitudes, as well as flexural rigidity. The uncertainty associated with the primary and secondary calculated parameters is investigated based on the known uncertainty in the measured parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Supersonic hot jet ablative testing and analysis of boron nitride nanotube hybrid composites

Boron nitride nanotubes (BNNTs) are high-strength, high-modulus nanotubes with high thermal and oxidative stabilities. Two hybrid composites were prepared with satin weave carbon fiber (CF) and resole-type phenolic resin: one with surface layers of BNNTs and one with alternating interlayers of BNNTs. The samples were subjected to hot jet tests that simulate realistic high-pressure-temperature conditions to understand the behavior of BNNTs under high-pressure erosion. Adding BNNTs to CF/phenolic laminates enhanced the ablation resistance by reinforcing the char material and mitigated localized thermal damage. Hybrid laminates exhibited up to 14% lower weight loss, 55% increase in flexural modulus, higher thermal diffusivity, and improved char yield and microstructure compared to CF/phenolic samples. The surface layer hybrid had many surviving nanotubes reinforcing the char and crystalline oxide structures that could mitigate further oxygen diffusion. Further, various characterization methods were used to deduce possible mechanisms and their products, indicating that BNNTs could serve as growth templates for direct crystalline boron oxide formation. Overall, hybrid BNNT/CF/phenolic laminates displayed better ablation resistance and favorable microstructure evolution under high-pressure conditions.

42 ENGINEERING↗
DOE OSTI2021

MXene Reinforced Thermosetting Composite for Lightning Strike Protection of Carbon Fiber Reinforced Polymer

Ti 3 C 2 – a member of the MXenes (2D transition metal carbides and nitrides) family, is investigated as an effective filler to improve the electrical, mechanical, and thermal properties of divinylbenzene (DVB) thermosetting resin. Consequently, its performance as a lightning strike protection (LSP) coating for carbon fiber reinforced polymer (CFRP) is evaluated. Polyaniline (PANI) – dodecylbenzene sulfonic acid (DBSA) complex is used to cure the DVB resin. The synergic effect of MXenes (with surface that is negatively charged) with polyaniline (positive charge) shows electrostatic bonding and improved electrical conductivity in the composite. We also find that the addition of MXenes at 2 wt% into the PANI-DVB composite shows ≈139%, 10%, and 9% improvement in electrical conductivity, flexural strength, and flexural modulus, respectively, compared to the neat PANI-DVB composite. The composites are investigated using various material characterization techniques including Fourier transforms infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and scanning electron microscopy. Furthermore, MXenes-DVB is utilized to create a conductive thermosetting coating on top of a CFRP substrate and tested against a lightning strike of 100 kA. CFRP with MXenes-DVB coating reduced the surface damage from 40.61 cm 2 (reference CFRP panel) to 13.29 cm 2 (CFRP coated with MXenes-DVB).

36 MATERIALS SCIENCE↗
DOE OSTI2025

DROP DURABILITY ASSESSMENT OF ELECTRONIC ASSEMBLIES UNDER OFF-AXIS LOADING WITH SKEWED FIXTURES

This thesis studies drop durability of electronic assemblies when the acceleration vector is oriented at 45° to the out-of-plane direction of the circuit card. The off-axis drop tests are accomplished with a skewed fixture and are conducted as a proxy for multiaxial drop testing. Advanced shock testing and vibration test methods have been developed over the last few decades to better represent real-world field environments during ground-based laboratory testing. However, many of these test methods require expensive and specialized equipment not available in most laboratories. An alternative approach for approximating simultaneous loading along multiple axes on conventional equipment utilizes skewed fixtures which have seen use in off-axis random vibration and drop impact testing. These methods generally rely on the conversion of a uniaxial input load from the test equipment (using a uniaxial drop tower or shaker) into a multiaxial load when resolved in the reference frame of the test article (mounted on a skewed fixture). Skewed fixture design is presented and recommendations for conducting skewed angle drop testing are introduced based on local measurements along the skewed face of the fixture to accurately monitor the impact event. Characterization tests were performed with a skewed fixture, at simultaneous acceleration loads from 500 to 3,000 g in two (in-plane and out-of-plane) directions, while meeting standard time domain tolerances. Upon experimental characterization, drop shock durability tests were conducted on a printed circuit assembly (PCA). Mean drops-to-failure were measured and quantified with Weibull statistics. Dominant solder joint failure modes were identified via failure analysis. Prior work on inclined angle impact testing is limited, and the majority of solder joint interconnect level fatigue studies are conducted considering perpendicular loading normal the circuit card. Low-cycle fatigue curves are generated based on plastic strain and plastic work density within the solder joint. A multiscale nonlinear finite element model is used to relate board-level flexure to solder joint interconnect level plastic strain. A high strain rate solder constitutive model allows for accurate modeling of solder plasticity resulting from high-impact drop shock. Fatigue parameters are computed from the Coffin-Manson relation and Palmgren-Miner damage accumulation. This work serves to apply established low-cycle fatigue methods for conventional drop shock loading (impact normal to circuit card) to non-perpendicular loading with a skewed fixture.

Hower, Jonathan [Kansas City National Security Cam↗
DOE OSTI2021

Detrital U-Pb zircon and 40 Ar/ 39 Ar muscovite geochronology from Middle Pennsylvanian strata in the Anadarko Basin, Texas Panhandle, USA

The Late Mississippian-Permian Anadarko Basin formed in Texas and Oklahoma, USA as the result of inversion of Neoproterozic and Cambrian rift structures. Subsidence was driven by flexural loading of the Amarillo-Wichita Uplift, and this uplift may represent the easternmost element of the Ancestral Rocky Mountains system. The northwestern part of this basin has generally been interpreted to have been filled by sediment derived from the Ancestral Front Range Uplift, ~475 km to the northwest during the early stages of basin filling. We test this model using U-Pb detrital zircon and 40 Ar/ 39 Ar detrital muscovite results from three subsurface samples of the Morrow B sandstone in the northwestern part of the Anadarko Basin. We provide a new maximum depositional age of 310.9 ± 4.9 Ma that indicates the age of the Morrow B to be no older than late Atokan to early Desmoinesian Age (Moscovian), ~10 Myr younger than previously interpreted. In contrast to some previous interpretations, we propose that the most likely source for the sediment in the Morrow B is the Amarillo Uplift to the south. Detrital zircon and detrital muscovite data have age peaks at 900–1300 Ma, 1370 Ma and 1600–1800 Ma corresponding to derivation from Grenville, Granite-Rhyolite and Yavapai-Mazatzal basement provinces, respectively. A dominant detrital zircon peak at 1370 Ma suggests that Mesoproterozoic granites in the Amarillo Uplift were exposed by Middle Pennsylvanian time, and detritus eroded from the Amarillo Uplift dominated the lowstand sediment budget of the Texas Panhandle during this time; small volumes of sediment were likely sourced from the Ancestral Front Range. In conclusion, this study presents the first detrital geochronology data from the subsurface Anadarko Basin and the first detrital muscovite data from late Paleozoic southwestern Laurentia. The results presented here highlight the interpretive power of combined detrital zircon and muscovite datasets.

58 GEOSCIENCES↗
DOE OSTI2022

Carbon nanofibers (CNFs) dispersed in ultra-high performance concrete (UHPC): Mechanical property, workability and permeability investigation

This paper presents experimental data on the effect of carbon nano-fiber (CNF) dispersion on mechanical behavior, workability, and permeability of ultra-high-performance concrete containing CNF (UHPC-CNF). The addition of CNFs in concrete has been shown to provide improved performance. However, an inhomogeneous distribution of CNFs in the cement matrix can result in no impact or decreased mechanical performance. Due to the van der Waal's forces and hydrophobic surface properties of the CNFs, good dispersion in mix fluids and cement paste is challenging. Experimental studies of UHPC-CNF with different dispersion methods are provided. Further mixing with optimized UHPC paste allowed for the investigation of the optimal dosage of CNFs, impact on porosity, compressive strength, flexural strength, hydration rate, and slump. Scanning electron microscopy (SEM) analysis visually revealed the effect of dispersion. Our results indicate that shear mixing and subsequent ultrasonic dispersion with chemical surfactants can provide a well-dispersion liquid admixture of CNFs resulting in high mechanical performance of UHPC-CNFs composites. The water permeability and chloride resistance of optimized UHPC-CNFs composites were further evaluated with the wicking test and ponding test to reveal improved performance for these properties as well.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Evaluation of Thermal & Mechanical Properties of Additively Manufactured Monolithic SiC for Solar Receiver Applications

Increasing the operating temperatures of solar receivers is paramount to the efficiency of concentrated solar thermal (CST) and solar power (CSP) systems. Owing to its high temperature stability combined with excellent thermal and optical properties, SiC has been the material of choice for application in high-temperature solar receivers. State-of-the-art SiC volumetric concentrating solar air receivers such as the honeycomb design have successfully demonstrated in field exit air temperatures approaching 800oC. However, a successful application of CST systems for the decarbonization of heat reliant industrial sectors requires significant increases in the temperature capability of SiC receiver technology. Supported by an award from the Solar Technology Office (SETO), US Department of Energy (DOE), GE Research in collaboration with Heliogen Holdings Inc, is engaged in the development of an ultra-High Operating Temperature SiC-matrix Solar Thermal Air Receiver (HOTSSTAR) enabled by additive manufacturing. The program objective is to design and demonstrate a techno-economically viable SiC air receiver technology that can achieve exit air temperatures up to 1100oC for CST applications. We report and discuss the results of our testing and evaluation of thermal and mechanical properties of reaction-bonded SiC fabricated via binder jet printing to support the receiver component design, development, and analyses.

14 SOLAR ENERGY↗