Search NASA⌕ Search

SEARCH · Search NASA

Results for “Geometry Process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Experimental and Numerical Study of Coating Thickness Using Multi-slot Air Knives

Gas-jet wiping is a widely employed production technology for controlling the final zinc coating thickness on a moving substrate during continuous hot-dip galvanizing. This paper presents an experimental investigation and numerical analysis of a prototype multi-slot air knife, which offers an increase in wiping efficiency relative to the traditional single-slot jet geometry in the continuous galvanizing process. The applicability of the analytical coating weight model of Elsaadawy et al. (Metall Mater Trans B, 38:413-424, 2007) to predict the final coating weight was determined for the multi-slot geometry, where particular focus was devoted to the effect of geometric parameters. Experimental measurements under a variety of knife geometry and process conditions agreed with the coating weight predictions of the analytical model. It was also shown that the air-knife geometric parameters had a significant effect on the pressure profile and shear stress distribution applied by the air knives to the moving substrate. It was determined that the final coating thickness was significantly affected by the auxiliary jet width, D{sub a}, where lighter coating weights at higher strip velocities (up to 5.4 pct at V{sub s} = 1.5 m/s) could be achieved by using the multi-slot air-knives prototype vs. the conventional single-slot configuration.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Design of fabric preforms for double diaphragm forming

Resin Transfer Molding (RTM) has the potential of becoming one of the most cost effective ways of producing composite structures since the raw materials used, resin and dry fabric, are less costly than prepregs. Unfortunately these low material costs are offset by the high labor costs incurred to layup the dry fabric into 3D shapes. To reduce the layup costs, double diaphragm forming is being investigated as a potential technique for creating a complex 3D preform from a simple flat layup. As part of our effort to develop double diaphragm forming into a production capable process, we have undertaken a series of experiments to investigate the interactions between process parameters, mold geometry, fabric weave, tow size, and the quality of the formed part. The results of these tests will be used to determine the forming geometry limitations of double diaphragm forming and to characterize the formability of fabric configurations. An important part of this work was the development of methods to measure and analyze fiber orientations, deformation angles, tow spreading, and shape conformation of the formed parts. This paper will describe the methods used to mark plies, the double diaphragm forming process, the techniques used to measure the formed parts, and the calculation of the parameters of interest. The results can be displayed as 3D contour plots. These experimental results have also been used to verify and improve a computer model which simulates the draping of fabrics over 3D mold shapes.

Luby, Steven↗
DOE OSTI2024

Modeling of Sagging for 3D Printed Layers During the Curing Process

Here, a printed layer of silica-enforced poly(dimethylsiloxane)-co-(diphenylsiloxane) is modeled as a two-phase system consisting of air and polymer with an interface set up during the printing process. The structural geometry changes mostly due to the action of surface tension, while all material properties are strongly temperature dependent. Polymer flow is described using equations of the extended Herschel–Bulkley model, with parameters strongly dependent on temperature and degree of curing. Parameters of the model are determined using flow sweep measurements and separate experiments with vertical structure sagging at different temperatures. The curing process is modeled using dependencies between the curing rate, degree of curing, and temperature obtained in studies by differential scanning calorimetry. The developed model is used for simulations of printed structure deformations with different initial and boundary conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Towards Multilayered Coatings of 304L Stainless Steels Using Friction Surfacing

Abstract The objective of this work is to study friction surfacing process variability when depositing multilayered coatings. This is motivated by the need to maintain deposition quality when depositing multiple friction surfacing layers, whether for repair, remanufacturing, or new part creation using this solid-state metal additive manufacturing process. In this study, 10-mm-diameter 304L stainless steel rods were used to create up to five layers of 40-mm-long coatings on 304L substrates using a constant set of processing parameters. In-process measurement of forces (X, Y, Z), flash temperature, flash geometry, layer temperature, and post-process measurement of layer geometry, microhardness, and microstructure are used to characterize changes in the friction surfacing process as more layers are deposited. It was observed that with increasing layers: layer thickness and deposition efficiency decrease; offsetting of the deposition towards the retreating side, and temperature in the deposited layer increase; and flash temperature does not change. Metallurgical analyses of friction-surfaced cross-sections revealed fine grain refinement and transformation of base austenite to strain-induced martensite. It is concluded that the process parameters need to be adjusted even after the second or third layer is deposited, corrections to the tool path are required after a couple of layers, and the measured process forces, as well as deposited layer temperature, may be useful to monitor and control the process and its instabilities.

Engineering↗
NASA NTRS2019

Bumper: A Tool for Analyzing Spacecraft Micrometeoroid and Orbital Debris Risk

“Bumper” is NASA’s computer program for analyzing spacecraft micrometeoroid and orbital debris (MMOD) risk. Bumper was developed in the late-1980s and has been continuously used and maintained since. The user base has grown from a few government entities to now include numerous commercial entities as well. The NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) Team is responsible for all aspects of the Bumper software. Bumper has been used to characterize MMOD risk on hundreds of spacecraft. All of the International Space Station (ISS) modules, visiting vehicles and numerous external components and systems have been analyzed. Bumper was used to analyze each of the Space Shuttle missions since STS-50. The Orion Multi-Purpose Crew Vehicle (MPCV) MMOD shielding is being developed using Bumper as well. Bumper has also been used on numerous telescopes (Hubble, James Webb, and Fermi Gamma-ray Space Telescopes), scientific probes (Stardust, New Horizons, Parker Solar Probe), and Earth observation satellites (Landsat, Joint Polar Satellite System). Bumper is also being used to analyze the micrometeoroid risk and support design of the Deep Space Gateway (DSG) and Mars Sample Return (MSR) missions. The HVIT Bumper Configuration Control Board (CCB) ensures that all changes to the code are approved, reviewed, and documented. Most of the changes are made to add new MMOD damage “ballistic limit equations” (BLEs). BLEs are typically added in response to completion of a hypervelocity impact (HVI) test series and development of an associated BLE. Other less frequent changes include updates of the debris or meteoroid environment models, feature enhancements, and feature retirement. Some BLEs are commercially sensitive and/or proprietary, so the CCB also manages code user-version control and software distribution. The current version – “Bumper 3” – is a FORTRAN executable that utilizes a 64-bit architecture. Bumper 3 has numerous features that make it a powerful tool for analyzing spacecraft MMOD risk. Bumper uses the latest orbital debris and micrometeoroid environment models. Bumper also easily processes large spacecraft geometry models, recognizes hidden surfaces, permits BLE assignment by name or number, and conducts quality checks of the spacecraft geometry model. Bumper 3 can also be used to estimate the effects of particle penetration through thin, high-standoff distance hardware components such as solar arrays and radiators. This is done using a special HVIT-developed technique know as the “3-Part Analysis.” The paper introduces the Bumper 3 MMOD risk analysis code and provides an example MMOD risk assessment showing Bumper’s role in the overall MMOD protection design process.

Lear, Dana M.↗
DOE OSTI2020

Geometry and dynamics of lipid membranes: The Scriven-Love number

The equations governing lipid membrane dynamics in planar, spherical, and cylindrical geometries are presented here. Unperturbed and first-order perturbed equations are determined and nondimensionalized. In membrane systems with a nonzero base flow, perturbed in-plane and out-of-plane quantities are found to vary over different length scales. Here, a new dimensionless number, named the Scriven-Love number, and the well-known Föppl–von Kármán number result from a scaling analysis. The Scriven-Love number compares out-of-plane forces arising from the in-plane, intramembrane viscous stresses to the familiar elastic bending forces, while the Föppl–von Kármán number compares tension to bending forces. Both numbers are calculated in past experimental works, and span a wide range of values in various biological processes across different geometries. In situations with large Scriven-Love and Föppl–von Kármán numbers, the dynamical response of a perturbed membrane is dominated by out-of-plane viscous and surface tension forces—with bending forces playing a negligible role. Calculations of non-negligible Scriven-Love numbers in various biological processes and in vitro experiments show in-plane intramembrane viscous flows cannot generally be ignored when analyzing lipid membrane behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Volumetric analysis and mesh generation of real and artificial microstructural geometries

Producing a viable finite element mesh of realistic microstructural structural geometry is a critical step in analyzing the thermo-mechanical behavior of complex multi-material composites. Advancements in imaging technology such as micro computed tomography have allowed modelers to access high resolution mesoscale geometries for direct numerical simulation. However, converting from voxel based 3D images to usable finite element meshes has been challenging. A robust method including algorithms and software scripts for generating finite element meshes from 3D imaged microstructures is presented in this paper. It includes a routine for inserting cohesive elements around material interfaces to enable modeling of interface properties including delamination and damage. The algorithms and procedures presented in this method leverage currently available software packages for processing surface based geometry into volume based meshes. In addition to converting real geometry from physical imaging systems, algorithms for producing numerically generated and statistically equivalent microstructural geometry are also included. These artificial microstructures can be a valuable resource for modelers when physical specimens do not exist or are limited in quantity: Method establishes a workflow from voxel data to viable finite element mesh including interface information, and Includes a method for synthetic geometry generation based on metrics from real microstructures.

36 MATERIALS SCIENCE↗
NASA NTRS1988

Digital image processing for quantification through full flow field tracing (FFFT) in narrow geometries at low Reynolds numbers

This paper introduces a computer based image processing technique to the field of nonintrusive velocity measurements in fluid mechanics. The method is presented with two alternatives: the first is involving intense interaction between the operator and the computer system; the second is a first generation artificial intelligence based system, where a set of initially imputed rules replaces the operator. The methods are applied to flow in narrow gaps.

Braun, M. J.↗
NASA NTRSDate not supplied

Towards Integrated Computational Materials Engineering for Quantifying Performance Impacts of Microstructure and Defect Interactions in Powder Bed Fusion Parts

Powder bed fusion (PBF) additive manufacturing (AM) enables the creation of parts with complexity and functionality levels that were previously impossible with traditional manufacturing methods. By modifying the laser power, hatch spacing, or the numerous other processing parameters, the PBF process supports the production of a wide set of materials and geometries. However, that same process parameter design flexibility causes the process-design space of PBF to be massive and expensive to explore experimentally. Another challenge is quality variation across a build. As a part is being built, geometric variance between locations, such as at a thin-wall section vs. the bulk material, may cause the specified processing parameters to no longer be acceptable for producing defect-free printing. Furthermore, if the processing parameters deviate during the print process, it is difficult to assess if the part will still perform satisfactorily. Integrated Computational Materials Engineering (ICME) provides a way to understand and address these various challenges. This talk will present advancements in process-structure simulations of PBF at NASA Langley Research Center. The ability to simulate grain-scale PBF microstructures using the Physically Based Monte Carlo method will be demonstrated and compared to experimental measurements. Techniques for simulating three-dimensional lack-of-fusion and keyhole porosity defects based on the specific processing conditions and approaches for integrating the two porosity prediction techniques alongside the computational microstructure evolution models will be shown. Finally, the integration of simulated PBF microstructures, embedded process defects, and crystal plasticity finite element models to elucidate the interaction of porosity and microstructure on micromechanical fields will be demonstrated. These integrated techniques demonstrate an example of using ICME to relate processing to performance for PBF AM materials. With continued maturity, it is hoped that such ICME approaches will lead to next-generation computational-materials supported qualification and certification of AM parts.

Additive manufacturing↗
NASA NTRS1989

Detection of edges using local geometry

Researchers described a new representation, the local geometry, for early visual processing which is motivated by results from biological vision. This representation is richer than is often used in image processing. It extracts more of the local structure available at each pixel in the image by using receptive fields that can be continuously rotated and that go to third order spatial variation. Early visual processing algorithms such as edge detectors and ridge detectors can be written in terms of various local geometries and are computationally tractable. For example, Canny's edge detector has been implemented in terms of a local geometry of order two, and a ridge detector in terms of a local geometry of order three. The edge detector in local geometry was applied to synthetic and real images and it was shown using simple interpolation schemes that sufficient information is available to locate edges with sub-pixel accuracy (to a resolution increase of at least a factor of five). This is reasonable even for noisy images because the local geometry fits a smooth surface - the Taylor series - to the discrete image data. Only local processing was used in the implementation so it can readily be implemented on parallel mesh machines such as the MPP. Researchers expect that other early visual algorithms, such as region growing, inflection point detection, and segmentation can also be implemented in terms of the local geometry and will provide sufficiently rich and robust representations for subsequent visual processing.

Gualtieri, J. A.↗
NASA NTRSDate not supplied

Boundary Representation Tolerance Impacts on Mesh Generation and Adaptation

The control of discretization error is critical to obtaining reliable simulation results. Re-cent progress has matured anisotropic mesh adaptation, which automates discretization error control for complex geometries. However, the meshing process can fail when geometric model Boundary REPresentation (BREP) tolerances are larger than boundary layer surface nor-mal and tangential spacing requirements. Geometry sources are often created in Mechanical Computer-Aided Design (MCAD) systems, which are designed to produce models for manufacturing and not the stricter requirements of viscous flow analysis. BREP tolerances are strained by three factors: the inherent complexity of the model (e.g., large range of scales and complex topology), the numerical difficulties arising from surface/surface intersections, and the omission of crucial data during export and translation. Manual preparation of geometry is commonly employed to enable expert-guided mesh generation, which severely inhibits work-flow automation. Accommodation of loose BREP tolerances is required for automated mesh processes, because barrier issues may not be detected until well into the solution process. To raise awareness of this class of geometry issues and their impact on simulation, a survey of these barrier issues is presented with example mitigation techniques. This awareness may also impact geometry creation workflows to prevent the introduction of these artifacts.

CAD↗
DOE OSTI2025

Accelerating detector simulations with Celeritas: Profiling and performance optimizations

Celeritas is a GPU-optimized Monte Carlo (MC) particle transport code designed to meet the growing computational demands of next-generation high energy physics (HEP) experiments. It provides efficient simulation of electromagnetic (EM) physics processes in complex geometries with magnetic fields, detector hit scoring, and seamless integration into Geant4-driven applications to offload EM physics to GPUs. Recent efforts have focused on performance optimizations and expanding profiling capabilities. This paper presents some key advancements, including the integration of the Perfetto system profiling tool for detailed performance analysis and the development of track-sorting methods to improve computational efficiency.

Lund, Amanda [Argonne National Laboratory (ANL)]↗
DOE OSTI2022

Understanding the Elastic, Plastic, and Damage Features in Fracturing of Self-reinforced Thermoplastic Composites via Non-destructive Digital Imaging Correlation

This work demonstrated the utilization of non-destructive Digital Imaging Correlation (DIC) method to characterize the elastic, plastic, and damage features during the Mode I intra-laminar fracturing process of self-reinforced thermoplastic composites by using a self-reinforced polypropylene (PP) composite as an example. The DIC results clearly showed the development of huge plastic zone (PZ) and non-negligible Fracture Process Zone (FPZ) in front of the notch tip during the fracturing process, and the geometries and sizes of the foregoing zones at the peak load were further quantified. Such an interesting fracturing behavior of self-reinforced thermoplastic composites is way different from brittle materials (e.g., glass, acrylic, etc.), ductile materials (e.g., aluminum, steel, etc.), and even quasi-brittle materials (e.g., concrete, nanoparticle-reinforced composites, tough ceramics, wood, cement, carbon/glass fiber-reinforced polymers, etc.). Thus, understanding the elastic, plastic, and damage features is the first step before better characterizing the material fracture properties of self-reinforced thermoplastic composites through new analytical methods and computational modeling. These efforts are of utmost importance for wide applications of self-reinforced thermoplastic composites in various engineering fields in the future.

Lightweight Composites, Self-reinforced Thermoplas↗
DOE OSTI2024

Advanced Manufacturing Basic Entity Relationships Ontology

A data ontology defined using the W3C Web Ontology Language (OWL) format. It defines classes and attributes for objects directly implicated in manufacturing such as materials, preform geometries, and manufacturing processes and settings. It also includes classes to describe entities that are instrumental to making digital twins and performing predictive activities on manufacturing data such as designs of experiment and predictive models.

Harris, BrennanKay↗
DOE OSTI2020

Application of an Erosion Wear Model to Predict Wear of Hammer Milling Components

A workable analytical erosion model that relates critical hammermill process parameters (hammermill geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness, toughness, and fatigue ductility) was applied to model wear (more specifically, change in the shape of hammers) in hammer milling operations. Results of the model were compared to experimental observations of the shape of hammers used in the INL Stage 1 Vermeer hammermill. Results showed good agreement between predicted and measured shape of the hammer, and that a quality-by-design (QbD) approach can be developed to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2021

An Abrasion Wear Model of Rotary Shear Comminution of Biomass Feedstock

The research team formulated a workable analytical abrasion model that relates critical rotary shear process parameters (shear geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness and elastic modulus) that enabled us to model the wear of shear cutters in a rotary shear milling system developed by Forest Concepts. We compared results of the model to experimental observations of the shape of rotary shear cutters used in a Forest Concept Crumbler® shear mill. Results showed good agreement between the predicted and measured shape of a worn cutter; thus, a quality-by-design (QbD) approach can be developed to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches.

42 ENGINEERING↗
DOE OSTI2022

Analysis of Cutter Blade Wear in Rotary Shear Mills

Following development of an analytical abrasive wear model to predict wear of components in a rotary shear mill, the team used a finite element analysis (FEA) approach to calculate forces and loads acting on particles responsible for abrasive wear. The analytical model related critical rotary shear process parameters (shear geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness and elastic modulus) that enabled us to model the wear of shear cutters in a rotary shear milling system developed by Forest Concepts. With proper knowledge of the forces acting between abrasive particles and cutter components built into it, the model can accurately predict wear of the cutters and provides a quality by design (QbD) approach to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches. During this reporting period, researchers at Oak Ridge National Laboratory applied an FEA package to simulate the local stresses and forces between an abrasive silica particle and two rotary shear cutters as the distance between the cutters decreases. The output of the FEA was used to provide more accurate projections of the loads applied to the particles in the analytical wear model. Comparison of the FEA force calculations are in good agreement with the loads assumed in the analytical predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Celeritas R&D Report: Accelerating Geant4

Celeritas is a new Monte Carlo (MC) detector simulation code designed for computationally intensive applications on high-performance heterogeneous architectures. In the past two years Celeritas has advanced from prototyping a Graphics Processing Unit (GPU)-based single physics model in infinite medium to implementing a full set of electromagnetic (EM) physics processes in complex geometries. The current release of Celeritas, version 0.4, has incorporated full device-based navigation, an event loop in the presence of magnetic fields, and detector hit scoring. New functionality incorporates a scheduler to offload electromagnetic physics to the GPU within a Geant4-driven simulation, enabling straightforward integration of Celeritas into the high energy physics (HEP) experimental frameworks CMSSW and ATLAS FullSimLight. On the Perlmutter supercomputer, Celeritas performs EM physics between 3× and 18× faster using the machine’s Nvidia GPUs compared to using only CPUs, corresponding to an electrical power efficiency up to a factor of 5. When running a multithreaded Geant4 ATLAS test beam application with full hadronic physics, using Celeritas to accelerate the EM physics results in an overall simulation speedup of 1.7–2.2× on GPU and 1.2× on CPU. In a CMS test application using tt¯ events and the prototype Run 4 configuration, compared to Geant4 CPU, Celeritas with a Nvidia A100 improves overall throughput up to a factor of 2.7× but cannot be efficiently shared with more than 8 cores.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗