Search NASA⌕ Search

SEARCH · Search NASA

Results for “HIGH THRUST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Nuclear Thermal Propulsion (NTP) Fission Product and Source Term Analysis

Nuclear thermal propulsion (NTP) is an in-space propulsion technology that uses a nuclear reactor to directly heat a propellant to provide high thrust, at higher efficiencies than achievable with conventional chemical propulsion systems. Due to the ability of NTP rockets to efficiently provide high thrust, this technology has been proposed for long duration space missions such as crewed missions to Mars and beyond. A primary hurdle for NTP technology development is the demonstration of an integrated reactor engine system to verify its functionality and performance. This primarily requires the manufacture and testing of candidate reactor and engine technologies to demonstrate the proposed design enables desired performance and exhibits acceptable response under all known operation modes. A major component in this testing is fission product accumulation, since after operation radioactive isotopes can be produced and pose radiological dose concerns. This paper explains the background behind fission product analysis and the methodology used to evaluate current reactor designs and identify the amount of fission products present and their radiological impact. Results of multiple thrust level engines at different time periods are discussed and highlight the need for additional experimental testing to confirm fractional release levels of fission products out of the system. Benchmarking of models and future paths of analysis are also discussed.

Nuclear Thermal Propulsion↗
NASA NTRS1990

Aerodynamic Performance of a 0.27-Scale Model of an AH-64 Helicopter with Baseline and Alternate Rotor Blade Sets

Performance of a 27 percent scale model rotor designed for the AH-64 helicopter (alternate rotor) was measured in hover and forward flight and compared against and AH-64 baseline rotor model. Thrust, rotor tip Mach number, advance ratio, and ground proximity were varied. In hover, at a nominal thrust coefficient of 0.0064, the power savings was about 6.4 percent for the alternate rotor compared to the baseline. The corresponding thrust increase at this condition was approx. 4.5 percent which represents an equivalent full scale increase in lift capability of about 660 lbs. Comparable results were noted in forward flight except for the high thrust, high speed cases investigated where the baseline rotor was slightly superior. Reduced performance at the higher thrusts and speeds was likely due to Reynolds number effects and blade elasticity differences.

Kelley, Henry L.↗
NASA NTRS1994

Sensitivity of lag-damping correlations to structural and aerodynamic approximations of isolated experimental rotors in forward flight

The predictions of regressive lag-mode damping levels are correlated with the database of an isolated, soft-inplane, three-blade rotor operated untrimmed. The database was generated at the Army Aeroflightdynamics Directorate at Ames. The correlation covers a broad range of data, from near-zero thrust conditions in hover to high-thrust and highly stalled conditions in forward flight with advance ratio as high as 0.55 and shaft angle as high as 20 degrees. In the experimental rotor, the airfoil or blade portion has essentially uniform mass and stiffness distributions, but the root flexure has highly nonuniform mass and stiffness distributions. Accordingly, the structural approximations refer to four models of root-flexure-blade assembly. They range from a rigid flap-lag model to three elastic flap-lag-torsion models, which differ in modeling the root flexure. The three models of root-flexure are: three root springs in which the bending-torsion couplings are fully accounted for; a finite-length beam element with some average mass and stiffness distributions such that the fundamental frequencies match those of the experimental model; and accurate modal representation in which the actual mass and stiffness distributions of the experimental root-flexure-blade assembly are used in calculating the nonrotating mode shapes. The four models of root-flexure-blade assembly are referred to as the rigid flap-lag model, spring model, modified model and modal model. For each of these four models of the root-flexure-blade assembly, the predictions are based on the following five aerodynamic theories: ear theory, which accounts for large angle-of-attack and reverse-flow effects on lift, and has constant drag and pitching moment; quasisteady stall theory, which includes quasisteady stall lift, drag and pitching moment characteristics of the airfoil section, dynamics stall theory, which uses the ONERA dynamic stall models of lift, drag and pitching moment; dynamic wake theory, which is based on a finite-state three-dimensional wake model and includes all wake effects including both shed and trailing vorticity; and dynamics and wake theory, which combines both dynamic stall theory and dynamic wake theory and is a relatively complete aerodynamic representation.

Gaonkar, G. H.↗
NASA NTRS1988

Tests of high current hollow cathodes for ion engines

The development of high power, high thrust ion engines requires the development of long life hollow cathodes capable of producing emission currents of hundreds of amperes. This paper describes results obtained through the extended testing of two 12.7 mm diameter hollow cathodes at high emission currents. The first cathode, operated on xenon for a total of 170 hours at an emission current of 100 A, sustained very little damage except for an increase in the cathode orifice diameter, from 0.953 to 1.71 mm. The second cathode was operated on xenon at 150 A emission current continuously for 24 hours, and for over 1000 hours at 100 A on argon with essentially no change in the cathode operating characteristics. Operation of this cathode was terminated due to severe erosion of several discharge chamber components located downstream of the cathode. The erosion of these components occurred despite operation at discharge voltages less than 24 volts, and poses a serious challenge to the sucessful implementation of multi-hundred ampere cathodes and high thrust ion engines.

Brophy, John R.↗
NASA NTRS2011

Cryo Propulsive Stage: HEFT Phase 2 Point of Departure

The CPS is an in-space high thrust propulsive stage based largely on state of the practice design for launch vehicle upper stages. However, unlike conventional propulsive stages, it also contains power generation and thermal control systems to limit the loss of liquid hydrogen and oxygen due to boil-off during extended in-space storage. The CPS provides high thrust GV for rapid transfer of in-space elements to their destinations or staging points (i.e., E-M L1). The CPS is designed around a block upgrade strategy to provide maximum mission/architecture flexibility: a) Block 1 CPS: Short duration flight times (hours), passive cryofluid management. b) Block 2 CPS: Long duration flight times (days/weeks/months), active and passive cryofluid management.

Martinez, Roland M.↗
NASA NTRS1992

Prospective new transportation application initiatives in NASA's earth-to-orbit propulsion technology program

NASA's Earth-to-Orbit (ETO) Propulsion Technology Program, a multi-year/multi-task focused technology effort is, today, highly focused on conventional high-thrust cryogenic liquid chemical rocket engines and their envisioned future technology needs. But as highlighted in the U.S. National Ten-Year Space Launch Technology Plan, a set of less-conventional propulsion subjects, ones which offer significant promise for both, improving the state of the art and opening up new propulsion-capability possibilities, is now directed to the space propulsion planning community's attention. In conducting its forward-planning activities, it is highly appropriate that the ETO Program (and other programs as well) carefully consider integrating these "new initiative" subjects into the taskwork of future years. After an introductory consideration of the National Plan's propulsion-related directives, followed by a brief background overview of the ETO Program, the following specific new-initiative candidates are discussed from the standpoint of technology-program planning: operationally efficient propulsion systems; high-thrust hybrid rocket propulsion; low-cost, low-pressure expendable propulsion subsystems; advanced cryogenic in-space propulsion systems; integrated modular engine (IME) configured propulsion systems, and combined-cycle airbreathing/rocket propulsion systems.

Escher, William J. D.↗
NASA NTRS2015

High Thrust-to-Power Annular Engine Technology

Gridded ion engines have the highest efficiency and total impulse of any mature electric propulsion technology, and have been successfully implemented for primary propulsion in both geocentric and heliocentric environments with excellent ground-in-space correlation of performance. However, they have not been optimized to maximize thrust-to-power, an important parameter for Earth orbit transfer applications. This publication discusses technology development work intended to maximize this parameter. These activities include investigating the capabilities of a non-conventional design approach, the annular engine, which has the potential of exceeding the thrust-to-power of other EP technologies. This publication discusses the status of this work, including the fabrication and initial tests of a large-area annular engine. This work is being conducted in collaboration among NASA Glenn Research Center, The Aerospace Corporation, and the University of Michigan.

electric propulsion↗
NASA NTRS2015

High Thrust-to-Power Annular Engine Technology

Gridded ion engines have the highest efficiency and total impulse of any mature electric propulsion technology, and have been successfully implemented for primary propulsion in both geocentric and heliocentric environments with excellent ground/in-space correlation of performance. However, they have not been optimized to maximize thrust-to-power, an important parameter for Earth orbit transfer applications. This publication discusses technology development work intended to maximize this parameter. These activities include investigating the capabilities of a non-conventional design approach, the annular engine, which has the potential of exceeding the thrust-to-power of other EP technologies. This publication discusses the status of this work, including the fabrication and initial tests of a large-area annular engine. This work is being conducted in collaboration among NASA Glenn Research Center, The Aerospace Corporation, and the University of Michigan.

Thruster↗
NASA NTRS1992

Combined high and low thrust propulsion for fast piloted Mars missions

The mission benefits of using both high thrust nuclear thermal propulsion (NTP) and low acceleration, high specific impulse nuclear electric propulsion (NEP) to reduce piloted trip times to Mars with reasonable initial mass are assessed. Recent updates in mission design, such as the Earth fly-by return, are assessed for their impact on previous studies. In addition, the Synthesis Commission split mission to Mars in 2014 is also assessed using combined propulsion. Results show an 80 to 100 day reduction in trip time over the reference NTP or NEP systems and missions, with comparable or reduced vehicle initial masses. The impacts of the mission and system analyses upon technology planning and design are discussed.

Gilland, James H.↗
NASA NTRS2011

Low Cost Nuclear Thermal Rocket Cermet Fuel Element Environment Testing

Deep space missions with large payloads require high specific impulse (Isp) and relatively high thrust in order to achieve mission goals in reasonable time frames. Conventional, storable propellants produce average Isp. Nuclear thermal rockets (NTR) capable of high Isp thrust have been proposed. NTR employs heat produced by fission reaction to heat and therefore accelerate hydrogen which is then forced through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3000K) and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high temperature hydrogen exposure on fuel elements is limited. The primary concern is the mechanical failure of fuel elements which employ high-melting-point metals, ceramics or a combination (cermet) as a structural matrix into which the nuclear fuel is distributed. It is not necessary to include fissile material in test samples intended to explore high temperature hydrogen exposure of the structural support matrices. A small-scale test bed designed to heat fuel element samples via non-contact RF heating and expose samples to hydrogen is being developed to assist in optimal material and manufacturing process selection without employing fissile material. This paper details the test bed design and results of testing conducted to date.

Bradley, David E.↗
NASA NTRS1991

Thrust stand for high-power electric propulsion devices

This paper describes a new high-power thrust stand developed for use with high-power (up to 250 kW) magnetoplasmadynamic (MPD) thrusters, which is installed in a high-vacuum MPD facility at Lewis Research Center. The design of the stand is based on inverted pendulum configuration, with the result of large displacements and high resolution. Calibration results showed that thrust measurements were linear and repeatable to within a fraction of 1 percent. The thrust stand was used for testing water-cooled MPD thrusters at power levels up to 125 kW. The thruster, however, is quite well suited for testing other types of electric propulsion devices.

Haag, T. W.↗
NASA NTRS1989

Heat Flux In A Dual-Throat Rocket Engine

Report describes tests of dual-throat rocket engine burning hydrogen in oxygen. In tests, heat-flux profiles measured in inner nozzle and outer chamber. Dual-throat engine being considered for advanced space transportation. Consisting of two combustion chambers in series operating separately or together, engine makes it possible to change mode of operation in flight to obtain performance in most advantageous regime. Produces high thrust at sea level or low thrust with higher performance at high altitudes or in space.

Ewen, R. L.↗
NASA NTRS2015

Multi-Objective Hybrid Optimal Control for Multiple-Flyby Interplanetary Mission Design Using Chemical Propulsion

Preliminary design of high-thrust interplanetary missions is a highly complex process. The mission designer must choose discrete parameters such as the number of flybys and the bodies at which those flybys are performed. For some missions, such as surveys of small bodies, the mission designer also contributes to target selection. In addition, real-valued decision variables, such as launch epoch, flight times, maneuver and flyby epochs, and flyby altitudes must be chosen. There are often many thousands of possible trajectories to be evaluated. The customer who commissions a trajectory design is not usually interested in a point solution, but rather the exploration of the trade space of trajectories between several different objective functions. This can be a very expensive process in terms of the number of human analyst hours required. An automated approach is therefore very desirable. This work presents such an approach by posing the impulsive mission design problem as a multiobjective hybrid optimal control problem. The method is demonstrated on several real-world problems.

Trajectory↗
NASA NTRS2002

Magnetized Target Fusion

Magnetized target fusion (MTF) is under consideration as a means of building a low mass, high specific impulse, and high thrust propulsion system for interplanetary travel. This unique combination is the result of the generation of a high temperature plasma by the nuclear fusion process. This plasma can then be deflected by magnetic fields to provide thrust. Fusion is initiated by a small traction of the energy generated in the magnetic coils due to the plasma's compression of the magnetic field. The power gain from a fusion reaction is such that inefficiencies due to thermal neutrons and coil losses can be overcome. Since the fusion reaction products are directly used for propulsion and the power to initiate the reaction is directly obtained from the thrust generation, no massive power supply for energy conversion is required. The result should be a low engine mass, high specific impulse and high thrust system. The key is to successfully initiate fusion as a proof-of-principle for this application. Currently MSFC is implementing MTF proof-of-principle experiments. This involves many technical details and ancillary investigations. Of these, selected pertinent issues include the properties, orientation and timing of the plasma guns and the convergence and interface development of the "pusher" plasma. Computer simulations of the target plasma's behavior under compression and the convergence and mixing of the gun plasma are under investigation. This work is to focus on the gun characterization and development as it relates to plasma initiation and repeatability.

Steven T. Griffin↗
NASA NTRS1979

The MPD thruster development program

Recent research results have inferred that the self-field magnetoplasmadynamic (MPD) thruster can attain efficiency and specific impulse levels which are competitive with ion thrusters. Based on these results, a program was initiated at JPL to develop this thruster for application on future spacecraft. Preliminary mission analyses have shown that the high thrust density MPD arcjet is advantageous for high power missions, such as a short trip time earth orbit transfer vehicle or a nuclear powered outer planet explorer. Direct thrust stand verification of the inferred performance levels used in these analyses is planned for a facility being assembled at Princeton University. A parallel effort at JPL is considering various thruster system configurations, energy storage concepts and propellant control techniques. In addition, a one pulse per second thruster test facility is planned at JPL to be used for thruster optimization studies including erosion and lifetime measurements.

Rudolph, L. K.↗
NASA NTRS1994

Test Plan. GCPS Task 4, subtask 4.2 thrust structure development

The Single Stage To Orbit (SSTO) vehicle is designed to lift off from a vertical position, go into orbit, return to earth for a horizontal landing, and be reusable for the next mission. (NASA baseline only) In order to meet its performance goals, the SSTO relies on light weight structure and the use of 8 tri-propellant engines. These engines are mounted to the thrust structure. This test plan addresses selection of the material for this structure, and the integrity of the design through testing of elements and a full-scale subcomponent. This test plan supports the development of the design for an advanced composite thrust structure for a Single Stage to Orbit manned, heavy launch vehicle. The thrust structure is designed to transmit very high thrust loads from the engines to the rest of the vehicle (see Figure 1 ). The thrust structure will also be used for primary attachment of the twin vertical tails and possibly act as the aft attach point for the wing. The combination of high loading, high vibration, long service life and high acoustic environments will need to be evaluated by tests. To minimize design risk, a building block approach will be used. We will first screen materials to determine which materials show the most promise for this application. Factors in this screening will be the suitability of these materials for chosen design concepts, particularly concerning specific strength, environmental compatibility and applicability to fabrication processes. Next we will characterize two material systems that will be used in the design; the characterization will allow us to generate preliminary design data that will be used for the analysis. Element testing will be performed to evaluate critical structural locations under load. Final testing on the full scale test article will be performed to verify the design and to demonstrate predictability of the analysis. Additionally, risks associated with fabricating full scale thrust structures will be reduced through testing activities. One of the major concerns that stems from full scale fabrication is the realities of size and the associated complexities of handling, manufacturing, and assembly. The need exists to fabricate, assemble and test_representative joint specimens to achieve_confidence in the design and manufacturing technologies being proposed.

Greenberg, H. S.↗