SEARCH · Search NASA

Results for “HOVERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Simulation investigation of the effects of helicopter hovering dynamics on pilot performance

A fixed base simulation has been performed to investigate the handling qualities requirements for the mid-term pitch response of a helicopter at hover and in low-speed flight. Pilot rating results from this simulation were compared with those from previous experiments to develop handling qualities limits on the frequency and damping of the oscillatory mode in the hovering cubic. Pilot performance data obtained during the experiment were used to confirm the pilot rating results. These data show the pilot performance to closely match that predicted by the theory of piloted control. A means of predicting pilot ratings from the open-loop aircraft dynamics is presented.

Aponso, Bimal L.↗

NASA NTRS1988

A comparison of theory and experiment for coupled rotor body stability of a bearingless rotor model in hover and forward flight

Seven cases were selected for correlation from a 1/5.86 Froude-scale experiment that examined several rotor designs which were being considered for full-scale flight testing as part of the Bearingless Main Rotor (BMR) program. The model rotor hub used in these tests consisted of back-to-back C-beams as flexbeam elements with a torque tube for pitch control. The first four cases selected from the experiment were hover tests which examined the effects on rotor stability of variations in hub-to-flexbeam coning, hub-to-flexbeam pitch, flexbeam-to-blade coning, and flexbeam-to-blade pitch. The final three cases were selected from the forward flight tests of optimum rotor configuration as defined during the hover test. The selected cases examined the effects of variations in forward speed, rotor speed, and shaft angle. Analytical results from Bell Helicopter Textron, Boeing Vertol, Sikorsky Aircraft, and the U.S. Army Aeromechanics Laboratory were compared with the data and the correlations ranged from poor-to-fair to fair-to-good.

Mirick, Paul H.↗

NASA NTRS1988

Comparisons of predicted and measured rotor performance in hover using a new free wake analysis

A new free-wake analysis has been developed to predict the performance of rotors in hover and axial flight. The analysis finds the rotor wake geometry using a novel influence coefficient/relaxation scheme. In this paper, the features of the analysis are reviewed, and the accuracy of the analysis is assessed for a wide range of rotor configurations in hover and vertical climb. The effects of variations in the analysis parameters are addressed, and recommendations for future development are presented. Generally good results were obtained for the predicted performance of a wide range of rotor geometries and operating conditions without any special 'tuning' of the analysis. The analysis also provides predictions of rotor performance in vertical climb that are substantially more accurate than momentum theory.

Felker, Fort F.↗

NASA NTRS1989

The free-wake prediction of rotor hover performance using a vortex embedding method

A method is developed to predict the rotor hover performance. This method solves the compressible mass conservation equation much like current full potential codes and can therefore predict the transonic flows on a rotor. However, the newly developed approach also allows for the free convection of shed vorticity and permits the computation of the entire hover wake system. The method uses a vortex embedding scheme in potential flow and has been implemented in a computer code, HELIX -I. To predict power we implement a simple boundary layer and two different induced-drag integration schemes. The induced-drag is obtained from surface pressure integration and an energy flux integral. Comparisons between computations and experiment show good agreement for the prediction of power polars, surface pressure distribution, and tip vortex geometry.

Ramachandran, K.↗

NASA NTRS1989

Rotorcraft deceleration to hover using image-based guidance

Rotorcraft operating in hostile environment fly at low altitudes to minimize exposure to the defensive weapons arrayed against them. The development of intelligent guidance commands at low altitudes requires the integration of conventional guidance with the information provided by the sensor on relative position between the vehicle and local terrain or obstacles. Deceleration to hover (DTH) is one of the common maneuvers executed by a rotorcraft. The authors describe the integration of DTH guidance logic with an image-based scheme to estimate the hover point. The performance of such a system is affected by parameters of the guidance and by navigation and image processing algorithms. Results are presented on the effect of the parameters on system performance.

Sridhar, Banavar↗

NASA NTRS1990

Effect of Blade Planform Variation on a Small-Scale Hovering Rotor

A hover test was conducted on a small-scale rotor model for three sets of tapered rotor blades and a baseline rectangular planform rotor blade. All configurations had the same airfoils, twist, and thrust-weighted solidity. The tapered blade planforms had taper initiating at 50, 75, and 94 percent of the blade radius with a taper ratio of 3 to 1 for each blade set. The experiment was conducted for a range of thrust coefficients, and the data were compared to the predictions of three hover analysis methods. The data show the 94 percent tapered blade was slightly more efficient at the higher rotor thrust levels. The other tapered planform rotors did not show the expected improvement over the baseline rotor, and all configurations had similar performance for low thrust coefficients. None of the analysis methods correlated well with the experimental data.

Althoff, Susan L.↗

NASA NTRS1990

Analysis of small-scale rotor hover performance data

Rotor hover-performance data from a 1/6-scale helicopter rotor are analyzed and the data sets compared for the effects of ambient wind, test stand configuration, differing test facilities, and scaling. The data are also compared to full scale hover data. The data exhibited high scatter, not entirely due to ambient wind conditions. Effects of download on the test stand proved to be the most significant influence on the measured data. Small-scale data correlated resonably well with full scale data; the correlation did not improve with Reynolds number corrections.

Kitaplioglu, Cahit↗

NASA NTRS1989

Tip vortex geometry of a hovering helicopter rotor in ground effect

The wide-field shadowgraph method has been used to photograph the tip vortices of a hovering helicopter rotor in ground effect. The shadowgraphs were used to obtain quantitative measurements of the rotor tip vortex geometry both in and out of ground effect. Many important phenomena are visible in the rotor wake using this method. These include the variation in descent and contraction rates of the tip vortices in ground effect, and the interaction between tip vortices in the far wake. The tip vortex geometry from the shadowgraphs is compared with the tip vortex geometry predicted using a free wake hover performance analysis. The free wake analysis accurately predicts the tip vortex geometry both in and out of ground effect. Performance data from the test is compared with the performance predicted using several methods, including the free wake analysis. All methods provided reasonable predictions for the helicopter performance in ground effect.

Light, Jeffrey S.↗

NASA NTRS1989

The effect of an unsteady three-dimensional wake on elastic blade-flapping eigenvalues in hover

This paper describes the formulation of a finite-state inflow model based on an acceleration potential and a helical wake geometry. The states of the model are coefficients of an inflow expansion in terms of a Fourier series (azimuthally) and of special polynomials (radially). The integrals over the wake are done in closed-form to obtain a set of ordinary differential equations for the inflow coefficients. The forcing functions for these equations are generalized forces which are integrals of the blade loading exactly as in structural dynamics. This model implicitly includes (for the hover case) Prandtl-Goldstein tip losses, dynamic inflow, and Theodorsen/Loewy lift deficiency. Thus, it is a fully three-dimensional unsteady wake model. Here, this model is coupled with elastic-blade equations in hover and eigenvalues are found. The results show that the three-dimensional wake has a large effect on the flap damping of all modes.

Peters, David A.↗

NASA NTRS1989

Theoretical and experimental investigation of the aeroelastic stability of an advanced bearingless rotor in hover and forward flight

The aeroelastic stability of a shaft-fixed, 1/8th Froude scaled bearingless rotor was investigated in a series of wind tunnel experiments simulating a wide range of operating conditions. A finite element formulation was used to perform a parallel theoretical analysis, with the goal of determining whether a bearingless rotor system could be made aeroelastically stable without the incorporation of auxilliary dampers. A quick estimate of lag mode damping was provided by a refined moving-block analysis implemented in real time which predicted similar damping values. Model rotor and blade properties were also determined, and these properties were used as inputs for a newly refined bearingless rotor analysis. Predicted results were compared with experimental results in hover and forward flight. Results indicated that soft pitch link stiffness increases pitch-lag coupling and stabilizes lag mode stability in hover and at low advance ratios, but destabilizes at higher advance ratios.

Wang, James M.↗

NASA NTRS1990

Model tilt-rotor hover performance and surface pressure measurement

A test of a small scale 3-bladed model rotor, with geometry typical of that used on tilt rotor aircraft, was conducted in the Army Aeroflightdynamics Directorate's anechoic hover chamber. The purpose was to determine the hover performance of the rotor and investigate the pressure distributions on a blade at various collective pitch angles and tip speeds. The measured pressures indicate that the rotor did not stall for high collective pitch angles up to theta sub c = 25 deg. This is clearly a 3-D effect since 2-D theory predicts flow separation at these high angles. The flow near the trailing edge separated above theta sub c = 25 deg which caused a sharp increase in power.

Tung, Chee↗

NASA NTRS1990

Analysis and prediction of tilt rotor hover noise

This paper presents new and improved tilt rotor hover noise prediction methods. Calculations include both discrete frequency harmonic noise and broadband noise mechanisms due to the ground plane/fountain recirculating flow. The noise mechanisms studied are thickness, loading, and inflow turbulence noise. In each case aeroacoustic models are developed and compared to noise measurements obtained experimentally for the XV-15 experimental tilt rotor aircraft. Both the effects of the mean and the turbulent fountain flows are found to be important noise sources and have strongly directional radiation patterns toward the rear of the aircraft (the direction of the rotor motion through the fountain flow). Calculations also show that the noise generated by the inflow of ambient atmospheric turbulence can also be an important noise source in hover in some directions. Further development of the methods and models, and precise information about the fountain flow, are needed to improve the predictions and to initiate noise minimization studies.

Coffen, Charles D.↗

NASA NTRS1991

Identification and simulation evaluation of an AH-64 helicopter hover math model

Frequency-domain parameter-identification techniques were used to develop a hover mathematical model of the AH-64 Apache helicopter from flight data. The unstable AH-64 bare-airframe characteristics without a stability-augmentation system were parameterized in the convectional stability-derivative form. To improve the model's vertical response, a simple transfer-function model approximating the effects of dynamic inflow was developed. Additional subcomponents of the vehicle were also modeled and simulated, such as a basic engine response for hover and the vehicle stick dynamic characteristics. The model, with and without stability augmentation, was then evaluated by AH-64 pilots in a moving-base simulation. It was the opinion of the pilots that the simulation was a satisfactory representation of the aircraft for the tasks of interest. The principal negative comment was that height control was more difficult in the simulation than in the aircraft.

Schroeder, J. A.↗

NASA NTRS1990

Wing force and surface pressure data from a hover test of a 0.658-scale V-22 rotor and wing

A hover test of a 0.658-scale V-22 rotor and wing was conducted in the 40 x 80 foot wind tunnel at Ames Research Center. The principal objective of the test was to measure the surface pressures and total download on a large scale V-22 wing in hover. The test configuration consisted of a single rotor and semispan wing on independent balance systems. A large image plane was used to represent the aircraft plane of symmetry. Wing flap angles ranging from 45 to 90 degrees were examined. Data were acquired for both directions of the rotor rotation relative to the wing. Steady and unsteady wing surface pressures, total wing forces, and rotor performance data are presented for all of the configurations that were tested.

Felker, Fort F.↗

NASA NTRS1992

An exploratory investigation of the flight dynamics effects of rotor rpm variations and rotor state feedback in hover

This paper presents the results of an analytical study conducted to investigate airframe/engine interface dynamics, and the influence of rotor speed variations on the flight dynamics of the helicopter in hover, and to explore the potential benefits of using rotor states as additional feedback signals in the flight control system. The analytical investigation required the development of a parametric high-order helicopter hover model, which included heave/yaw body motion, the rotor speed degree of freedom, rotor blade motion in flapping and lead-lag, inflow dynamics, a drive train model with a flexible rotor shaft, and an engine/rpm governor. First, the model was used to gain insight into the engine/drive train/rotor system dynamics and to obtain an improved simple formula for easy estimation of the dominant first torsional mode, which is important in the dynamic integration of the engine and airframe system. Then, a linearized version of the model was used to investigate the effects of rotor speed variations and rotor state feedback on helicopter flight dynamics. Results show that, by including rotor speed variations, the effective vertical damping decreases significantly from that calculated with a constant speed assumption, thereby providing a better correlation with flight test data. Higher closed-loop bandwidths appear to be more readily achievable with rotor state feedback. The results also indicate that both aircraft and rotor flapping responses to gust disturbance are significantly attenuated when rotor state feedback is used.

Chen, Robert T. N.↗

NASA NTRS1993

Jet-induced ground effects on a parametric flat-plate model in hover

The jet-induced forces generated on short takeoff and vertical landing (STOVL) aircraft when in close proximity to the ground can have a significant effect on aircraft performance. Therefore, accurate predictions of these aerodynamic characteristics are highly desirable. Empirical procedures for estimating jet-induced forces during the vertical/short takeoff and landing (V/STOL) portions of the flight envelope are currently limited in accuracy. The jet-induced force data presented significantly add to the current STOVL configurations data base. Further development of empirical prediction methods for jet-induced forces, to provide more configuration diversity and improved overall accuracy, depends on the viability of this STOVL data base. The data base may also be used to validate computational fluid dynamics (CFD) analysis codes. The hover data obtained at the NASA Ames Jet Calibration and Hover Test (JCAHT) facility for a parametric flat-plate model is presented. The model tested was designed to allow variations in the planform aspect ratio, number of jets, nozzle shape, and jet location. There were 31 different planform/nozzle configurations tested. Each configuration had numerous pressure taps installed to measure the pressures on the undersurface of the model. All pressure data along with the balance jet-induced lift and pitching-moment increments are tabulated. For selected runs, pressure data are presented in the form of contour plots that show lines of constant pressure coefficient on the model undersurface. Nozzle-thrust calibrations and jet flow-pressure survey information are also provided.

Wardwell, Douglas A.↗

NASA NTRS1993

Robust crossfeed design for hovering rotorcraft

Control law design for rotorcraft fly-by-wire systems normally attempts to decouple angular responses using fixed-gain crossfeeds. This approach can lead to poor decoupling over the frequency range of pilot inputs and increase the load on the feedback loops. In order to improve the decoupling performance, dynamic crossfeeds may be adopted. Moreover, because of the large changes that occur in rotorcraft dynamics due to small changes about the nominal design condition, especially for near-hovering flight, the crossfeed design must be 'robust.' A new low-order matching method is presented here to design robost crossfeed compensators for multi-input, multi-output (MIMO) systems. The technique identifies degrees-of-freedom that can be decoupled using crossfeeds, given an anticipated set of parameter variations for the range of flight conditions of concern. Cross-coupling is then reduced for degrees-of-freedom that can use crossfeed compensation by minimizing off-axis response magnitude average and variance. Results are presented for the analysis of pitch, roll, yaw, and heave coupling of the UH-60 Black Hawk helicopter in near-hovering flight. Robust crossfeeds are designed that show significant improvement in decoupling performance and robustness over nominal, single design point, compensators. The design method and results are presented in an easily-used graphical format that lends significant physical insight to the design procedure. This plant pre-compensation technique is an appropriate preliminary step to the design of robust feedback control laws for rotorcraft.

Catapang, David R.↗

NASA NTRS1992

Hover performance validation of an ejector configured STOVL fighter aircraft

The hover thrust performance of a full-scale model of an ejector-lift/vectored thrust Short Take-Off and Vertical Landing (STOVL) fighter configuration was measured at the Outdoor Aerodynamic Research Facility of the National Full-Scale Aerodynamics Complex located at NASA Ames Research Center. The static thrust of the lifting ejector and ventral nozzle was calibrated at an out-of-ground-effect height. The test permitted comparison with static thrust calibrations obtained in the 80- by 120-Foot Wind Tunnel. The average static thrust augmentation ratio of the ejector system was 1.55 compared with the design goal of 1.63. The outdoor test showed that the addition of short extensions to the diffuser on the fuselage sidewall decreased suckdown and increased ejector performance. As expected, an increase in the ventral nozzle thrust deflection angle from nearly horizontal to the vertical-lift hover position caused a significant decrease in thrust. Flow visualization using smoke revealed greater secondary airflow into the left ejector and the penetration of hot ventral gases along the ground beneath and between the cool plumes from the ejector system.

Naumowicz, Tim↗