Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hall measurements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Epitaxial growth of rock salt MgZrN 2 semiconductors on MgO and GaN

Ternary nitride compound semiconductors have attracted recent attention as electronic materials since their properties can be tuned by cation stoichiometry and ordering. A recently discovered example is MgZrN 2 , a ternary analog to the rock salt semiconductor ScN. MgZrN 2 has a larger bandgap and stronger dielectric response than the binary compound. Polycrystalline thin films of MgZrN 2 have been studied, but demonstration of high-quality growth is still required to establish its suitability for technological applications. Here, we report on epitaxial growth of MgZrN 2 thin films on (100) and (111) MgO substrates and (001) GaN templates. The MgZrN 2 composition is confirmed by Rutherford backscattering spectrometry, showing no oxygen in the film except for a thin surface oxide layer. Epitaxial growth results in MgZrN 2 with x-ray diffraction rocking curves with a full-width at half-maximum in the range of 0.3–3.0°, depending on the substrate. Transmission electron microscopy analysis of the MgZrN 2 film grown on a (111) MgO substrate confirms epitaxial growth and shows a sharp film/substrate interface. In-plane temperature-dependent Hall effect measurements show that the material is an n-type semiconductor with a relatively high concentration ( n 300K ≈ 10 19 –10 20 cm -3 ) of thermally activated electrons. Room-temperature transport measurements show a conductivity of 25 S cm -1 and a Seebeck coefficient of -80 μ V K -1 . Overall, these results provide an important step toward integration of rock salt MgZrN 2 with other technological nitrides for device applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The role of low Gd concentrations on magnetisation behaviour in rare earth:transition metal alloy films

The magnetisation reversal behaviour as a function of composition was studied in low rare earth concentration alloys. 30 nm thick rare earth:transition-metal films of composition GdxCo 100-x , GdxFe 100-x and Gd x (Co 50 Fe 50 ) 100-x were prepared by magnetron sputtering, where x ranged from 4 to 13 atomic%. Magnetisation behaviour was studied using MOKE and Hall hysteresis measurements. The magnetic reversal behaviour as a function of Gd content is strongly dependent on the transition metal. With increasing Gd content the film structure transitions from crystalline to amorphous and the saturation magnetisation decreases linearly. For GdCo, the reversal field, Hc, increases by less than a factor of two with Gd doping of 11%, while for Fe, the coercivity falls by a factor of ten with 8% Gd. This may be attributed to changes in the crystalline morphology. GdCoFe shows a similar trend with Gd doping for the in-plane reversal field to that of GdFe. With 13% Gd in Fe there is evidence indicating the presence of a weak perpendicular magnetic anisotropy, PMA. With Gd doping the anomalous Hall resistivity of Co, Fe and CoFe increases significantly with the largest increase observed for GdCoFe.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Large non-saturating Nernst thermopower and magnetoresistance in compensated semimetal ScSb

Today, high-performance thermoelectric and thermomagnetic materials operating in the low-temperature regime, particularly below the boiling point of liquid nitrogen remain scarce. Most thermomagnetic materials reported to date exhibit a strong Nernst signal along specific crystallographic directions in their single-crystal form. However, their performance typically degrades significantly in the polycrystalline form. Here, we report an improved Nernst thermopower of ~ 128 μV/K at 30 K and 14 T in polycrystalline compensated semimetal ScSb, in comparison to that was observed in single crystal ScSb previously. The magnetic field dependence of Nernst thermopower shows a linear and non-saturating behavior up to 14 T. The maximum Nernst power factor reaches to ~ 240 x 10 -4 W m −1 K −2 and Nernst figure of merit reaches to ~ 11 x 10 -4 K −1 . Polycrystalline ScSb also shows a large non-saturating magnetoresistance of ~ 940% at 2 K and 14 T. These enhanced properties originate from better electron–hole compensation, as revealed by Hall resistivity measurements. In conclusion, the cubic symmetry and absence of anisotropy in ScSb allow its polycrystalline form to achieve similar enhanced thermomagnetic and electromagnetic performance comparable to that of the single crystal.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Quantum oscillations with angular dependence in PdTe 2 single crystals

The layered transition-metal dichalcogenide PdTe 2 has been discovered to possess bulk Dirac points as well as topological surface states. By measuring the magnetization (up to 7 T) and magnetic torque (up to 35 T) in single crystalline PdTe2, we observe distinct de Haas–van Alphen (dHvA) oscillations. Eight frequencies are identified with H||c, with two low frequencies (F α = 8 T and F β = 117 T) dominating the spectrum. The effective masses obtained by fitting the Lifshitz–Kosevich (LK) equation to the data are $m_α^* =0.059m_0$ and $m_β^* =0.067m_0$ where $m_0$ is the free electron mass. The corresponding Landau fan diagrams allow the determination of the Berry phase for these oscillations resulting in values of ~0.67π for the 3D α band (hole-type) (down to the 1st Landau level) and ~0.23π–0.73π for the 3D β band (electron-type) (down to the 3rd Landau level). By investigating the angular dependence of the dHvA oscillations, we find that the frequencies and the corresponding Berry phase (Φ B ) vary with the field direction, with a Φ B ~ 0 when H is 10°–30° away from the ab plane for both α and β bands. Finally, the multiple band nature of PdTe 2 is further confirmed from Hall effect measurements.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Structural and Electronic Properties of Indium-Doped n-type Cd-Se-Te Crystals

Here, we present a comprehensive investigation into the potential of n-type indium-doped cadmium selenide telluride (CST:In) as a high-performance candidate for solar cell applications, without the need for resource-intensive post-growth treatments that are required for CdTe:In. We compared undoped CST and CST:In crystals under different growth conditions, analyzing their structural and electronic properties using x-ray diffraction (XRD), electron probe microanalysis (EPMA), current-voltage (IV) and Hall effect measurements, time-resolved photoluminescence (TRPL), optical transmission, and photoluminescence (PL) mapping. The results reveal that as-grown CST:In crystals achieve nearly 100% carrier activation, yielding an electron concentration of 9.5x1018 cm -3 , mobility of 653 cm 2 /V.s and a 5 ns lifetime which approaches the radiative limit. Furthermore, comparison of PL maps from crystal growths having different cooling profiles suggests a strong effect of cooling rate on selenium segregation and cubic/hexagonal/polytype phase distribution. Slower cooling leads to a more homogeneous cubic structure with lower Se segregation, while a faster cooling rate results in increased Se segregation, and twin boundaries and stacking faults with polytypic and hexagonal character.

14 SOLAR ENERGY↗
DOE OSTI2021

On the mechanism of ionization oscillations in Hall thrusters

Low-frequency ionization oscillations involving plasma and neutral density (breathing modes) are the most violent perturbations in Hall thrusters for electric propulsion. Because of its simplicity, the zero-dimensional (0D) predator–prey model of two nonlinearly coupled ordinary differential equations for plasma and neutral density has often been used for the characterization of such oscillations and scaling estimates. In this work, we investigate the properties of its continuum analog, the one-dimensional (1D) system of two nonlinearly coupled equations in partial derivatives (PDEs) for plasma and neutral density. This is a more general model, of which the standard 0D predator–prey model is a special limit case. We show that the 1D model is stable and does not show any oscillations for the boundary conditions relevant to Hall thrusters and the uniform ion velocity. We then propose a reduced 1D model based on two coupled PDEs for plasma and neutral densities that is unstable and exhibit oscillations if the ion velocity profile with the near-the-anode back-flow (toward the anode) region is used. Comparisons of the reduced model with the predictions of the full model that takes into account the self-consistent plasma response show that the main properties of the breathing mode are well captured. In particular, it is shown that the frequency of the breathing mode oscillations is weakly dependent on the final ion velocity but shows a strong correlation with the width of the ion back-flow region.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Electrical Switching and Imaging of Antiferromagnetic Spins in Perovskite Epitaxial Thin Films

Electrical control of antiferromagnets is essential for the field of antiferromagnetic spintronics that promises ultrafast speed and terahertz dynamics. However, the large family of complex oxide antiferromagnets such as perovskites have been largely unexplored. Here, we demonstrate electrical switching and detection of Néel vector in LaFeO 3 epitaxial thin films with an epitaxy-enabled biaxial anisotropy, of which the switching behavior is understood by comparing to magnetic field controlled spin Hall magnetoresistance measurements. The electrical switching is corroborated by imaging of antiferromagnetic domains using X-ray Magnetic Linear Dichroism Photoemission Electron Microscopy. Electrical switching of 3-nm and 10-nm LaFeO 3 films was achieved over a wide temperature range of 25 to 300 K. This work offers an attractive platform for exploration of antiferromagnetic spintronics and other emerging phenomena such as potential insulating altermagnetism.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Inert Gas Element as Active Infrared‐Absorption Source and Donor in Silicon for Forbidden‐Wavelength Sensing

Intrinsic silicon (Si) is forbidden for infrared (IR) sensing at the communication wavelength like 1.31 or 1.55 µm due to the well‐known bandgap limitation. In this work, an unexpected physical picture of using argon (Ar) is identified, which is usually inert to the surrounding chemical environment and used as a protective agent in semiconductor processing, to overcome the IR‐sensing‐forbidden problem in Si. Here, in this work, it is shown by an analysis of a dynamic secondary ion mass spectrometer that such a Si, when exposed to laser pulse in Ar gas, can contain a very high dose of Ar up to 10 20 cm −3 even after 1300 days. First‐principles calculations, molecular dynamics, and Hall effect measurements reveal that, due to both steric and dynamic repulsions by Ar orbitals to Si dangling bonds, the Ar‐filled‐vacancy produces a much wider defect band inside the gap, which is not only responsible for strong infrared absorption, but also causes a significant increase in n‐type conductivity, both in line with experiments. The study proves that originally inert elements in fact can act as active impurities in semiconductors for advanced applications, which updates the current knowledge of defect physics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Hall Effect Characterization of α ‐Irradiated p‐Type 4H‐SiC

Most electrical characterization of radiation damage to semiconductors is conducted on full devices or on low‐doped material. However, evaluating the radiation hardness is challenging in less mature semiconductor systems where low‐doped material is unavailable and full devices are difficult to realize. Herein, temperature‐dependent Hall effect measurements are used to demonstrate α particle‐induced radiation effects in p‐type 4H‐SiC with a room temperature hole concentration of . The 4H‐SiC is irradiated by α particles from a 210 Po source over a fluence of –. Modeling the hole concentration as a function of temperature shows that α radiation causes hole compensation through the introduction of hole traps. The radiation also induces a reduction in hole mobility due to an increase in defect‐related scattering centers. At low temperatures and increasingly higher fluences, the conduction mechanism changes from band conduction to another mechanism.

Frye, Clint D.↗
DOE OSTI2023

Enhancing the performance of the perovskite solar cells by modifying the SnO 2 electron transport layer

The tin oxide (SnO 2 ) electron transport layer (ETL) plays a vital role in the photo-conversion efficiency (PCE) and stability of organic-inorganic perovskite solar cells (PSCs). However, SnO 2 ETL-induced defects such as hydroxyl groups, oxygen vacancies, exposed Sn atoms, and dangling bonds hinder device performance. In this study, rubidium chloride (RbCl) has been used to modify the SnO 2 ETL. Perovskite film formed on the RbCl-modified SnO 2 ETL exhibits improved crystallinity with enlarged grain size and reduced grain boundaries and enhanced optical absorption. Further, the Hall-effect measurements indicate the improved carrier mobility, and the dark J-V curve shows the increment of electrical conductivity for the RbCl-modified SnO 2 ETL. X-ray photoelectron spectroscopy (XPS) results demonstrate the surface defects passivation of the perovskite layer by modifying the SnO 2 ETL. A champion PCE of 19.35% has been achieved for the RbCl-modified SnO 2 ETL-based devices with improved stability, while the control devices with unmodified SnO 2 ETL show a PCE of 17.18%.

14 SOLAR ENERGY↗
DOE OSTI2026

The BigBite Calorimeter for the Super Bigbite Spectrometer Program at Jefferson Lab

Here, we report features of the design, construction, installation, and performance of the BigBite Calorimeter (BBCal), a lead-glass electromagnetic calorimeter constructed as part of the BigBite Spectrometer (BBS), which served as the electron arm for the Super Bigbite Spectrometer (SBS) program of high-precision neutron electromagnetic form factor measurements in Hall A at Jefferson Lab. As a total-absorption calorimeter, BBCal provided the primary electron trigger for BBS, detecting quasi-elastically scattered electrons in the 1–4 GeV energy range with an energy resolution of approximately 6.2%, position resolution of 1.2 cm, and timing resolution of 0.5 ns.

BBCal↗
DOE OSTI2025

Fabrication of nanoporous doped metal oxide coatings via selective infiltration of a block copolymer template: The case of Al-doped zinc oxide

Conductive nanoporous conformal coatings are important for various applications including touchscreens, displays, and electrochromic windows, though design of such coating with controlled porosity and composition remains challenging. We propose a sequential infiltration synthesis (SIS) method for the fabrication of nanoporous conductive aluminum-doped zinc oxide (AZO) films by infiltrating block copolymer (BCP) templates, specifically polystyrene-block-polyvinyl pyridine (PS-b-P4VP), with diethyl zinc and trimethyl aluminum precursors. Tunability of both porosity and electrical conductivity is achieved by precisely controlling the swelling behavior of the polymer templates and adjusting the number of SIS cycles. Further, our results reveal that porosity levels can reach up to 80 %, with resistivity as low as ~7.83 Ωcm. Using conductive atomic force microscopy (C-AFM) and Hall effect measurements, we show that lower concentrations of aluminum doping relative to zinc (around 1: 17) results in higher conductivity of the AZO films. Additionally, AZO is based on zinc oxide (ZnO) which is cost-efficient, abundant and less toxic than commonly used transparent conductive oxides such as indium tin oxide (ITO) and fluorine-doped tin oxide (FTO). Therefore, this novel approach opens new possibilities for creating highly porous, conformal, conductive AZO coatings with customizable porosity and composition, making them ideal candidates for diverse optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Influence of Copper Composition on Cu 2 BaSn(S,Se) 4 Solution-Deposited Films and Photovoltaic Devices with Over 5% Efficiency

Cu 2 BaSn(S,Se) 4 is currently in the spotlight for prospective environmentally friendly, stable, thin-film solar cell application, with demonstrated device power conversion efficiency (PCE) exceeding 5% for vacuum-deposited absorbers. As suggested by first-principles calculations, experimental studies involving related Cu 2 ZnSn(S,Se) 4 and Cu(In,Ga)(S,Se) 2 absorbers prove that the detailed chemical composition typically plays a sensitive role in altering defects and electronic properties of these complicated compound semiconductors. Herein, the copper composition of Cu 2 BaSn(S,Se) 4 has been systematically modified, employing a solution-based deposition approach, to provide a more complete picture of the phase stability and optoelectronic property sensitivity for this material. X-ray diffraction and scanning electron microscopy show that phase purity is preserved over a film Cu content range of nominally 0.94 ≤ [Cu]/[Ba + Sn] ≤ 1.01. Terahertz spectroscopy and Hall effect measurements reveal that the majority carrier hole density of ~10 13 cm –3 and mobility (~5 cm 2 /V s), as well as the minority carrier lifetime (a bulk lifetime of 180 ps and a surface recombination velocity >106 cm/s), are nominally independent of Cu content. The champion PCEs exceed 4.7% for all copper compositions in the phase-pure region, with a record value of 5.1%, similar to the reported values for record vacuum-deposited devices. Furthermore, these results suggest that Cu 2 BaSn(S,Se) 4 films and solar cells (at the current performance level) may be less sensitive to Cu stoichiometry compared to kesterite materials and therefore may provide a more stable material platform to prepare thin-film solar cells.

(CBTSSe)↗
DOE OSTI2020

Variable spin-charge conversion across metal-insulator transition

The charge-to-spin conversion efficiency is a crucial parameter in determining the performance of many useful spintronic materials. Usually, this conversion efficiency is predetermined by the intrinsic nature of solid-state materials, which cannot be easily modified without invoking chemical or structural changes in the underlying system. Here we report on successful modulation of charge-spin conversion efficiency via the metal-insulator transition in a quintessential strongly correlated electron compound vanadium dioxide (VO2). By employing ferromagnetic resonance driven spin pumping and the inverse spin Hall effect measurement, we find a dramatic change in the spin pumping signal (decrease by > 80%) and charge-spin conversion efficiency (increase by five times) upon insulator to metal transition. The abrupt change in the structural and electrical properties of this material therefore provides useful insights on the spin related physics in a strongly correlated material undergoing a phase transition.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Light-wave-controlled Haldane model in monolayer hexagonal boron nitride

In recent years, the stacking and twisting of atom-thin structures with matching crystal symmetry has provided a unique way to create new superlattice structures in which new properties emerge. In parallel, control over the temporal characteristics of strong light fields has allowed researchers to manipulate coherent electron transport in such atom-thin structures on sublaser-cycle timescales. Here we demonstrate a tailored light-wave-driven analogue to twisted layer stacking. Tailoring the spatial symmetry of the light waveform to that of the lattice of a hexagonal boron nitride monolayer and then twisting this waveform result in optical control of time-reversal symmetry breaking and the realization of the topological Haldane model in a laser-dressed two-dimensional insulating crystal. Further, the parameters of the effective Haldane-type Hamiltonian can be controlled by rotating the light waveform, thus enabling ultrafast switching between band structure configurations and allowing unprecedented control over the magnitude, location and curvature of the bandgap. This results in an asymmetric population between complementary quantum valleys that leads to a measurable valley Hall current, which can be detected by optical harmonic polarimetry. The universality and robustness of our scheme paves the way to valley-selective bandgap engineering on the fly and unlocks the possibility of creating few-femtosecond switches with quantum degrees of freedom.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Optoelectronic property comparison for isostructural Cu 2 BaGeSe 4 and Cu 2 BaSnS 4 solar absorbers

To target mitigation of anti-site defect formation in Cu 2 ZnSnS 4–x Se x , a new class of chalcogenides, for which Ba or Sr (group 2) replace Zn (group 12), has recently been introduced for prospective solar absorber application. Cu 2 BaGeSe 4 (CBGSe) and Cu 2 BaSnS 4 (CBTS) are two such compounds, which share a common trigonal crystal structure (P3 1 space group) and similar quasi-direct band gap (~2 eV). While CBTS-based films have already been studied, there are no reports yet on films and solar cells based on related CBGSe. To identify key differences and similarities in the electronic properties between these two materials, electronic characteristics (e.g., carrier concentration, mobility, electron affinity, defect levels, recombination, and charge carrier kinetics) of vacuum-deposited CBGSe and CBTS films are compared using a variety of characterization methods. Hall effect measurements reveal that CBGSe films have relatively higher hole carrier concentration and lower mobility (3 × 10 15 cm –3 , 0.6 cm 2 V –1 s –1 ) compared to CBTS (5 × 10 12 cm –3 , 3.5 cm 2 V –1 s –1 ). Photoelectron spectroscopy yields low electron affinity values for both CBGSe (3.7 eV) and CBTS (3.3 eV), pointing to the necessity of pursuing low electron affinity buffer materials for both types of absorbers. At low temperatures, CBGSe films show free-exciton photoluminescence, as well as pronounced deep-level emission at ~1.4 eV, while CBTS films exhibit a strong bound-exciton signal with noticeably less intense deep-level emission than for CBGSe. Charge carrier kinetics, transport, and recombination properties of both types of films are also analyzed using optical-pump terahertz-probe spectroscopy and time-resolved microwave conductivity. The first CBGSe prototype solar cells (using chemical bath deposited CdS as a buffer layer) show a maximum of 1.5% efficiency with ~0.62 V open-circuit voltage. Furthermore, the measured properties point to possible limiting factors for CBGSe and related films for PV and optoelectronics and provide insights on possible approaches for improvement within this multinary chalcogenide family.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The role of chemical potential in compensation control in Si:AlGaN

Reduction in compensation in Si-doped Al-rich AlGaN is demonstrated via chemical potential control (CPC). The chemical potentials and the resulting formation energies of carbon on the nitrogen site (C N ) and cation vacancy complex with Si (V III + nSi III ) were related to growth variables through a thermodynamic supersaturation model, which quantitatively predicted the incorporation of C N and the generation of the V III + nSi III complex. The compensation “knee” behavior, i.e., decreasing conductivity with increasing Si incorporation beyond a certain concentration, was successfully controlled. The maximum free carrier concentration was improved by impeding the formation of V III + nSIi III complexes under III-richer conditions, while the impurity compensation by C N was reduced by making the growth environment N-richer. The results of Hall effect measurement and photoluminescence agreed well with quantitative theoretical predictions of the CPC model. Based on the developed model, the highest conductivity of 160 Ω -1 cm -1 with free carrier concentration of 3 × 10 19 cm -3 in Al 0.7 Ga 0.3 N ever reported was achieved on single crystal AlN substrates. The demonstrated predictive power of the CPC model should greatly reduce the empirical analysis or iterative experimentation that would otherwise be necessary.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗