Results for “Hydrothermal carbonization” — Page 6

NASA NTRS2010

Experimental Study of Abiotic Organic Synthesis at High Temperature and Pressure Conditions: Carbon Isotope and Mineral Surface Characterizations

Abiotic organic synthesis processes have been proposed as potential mechanisms for methane generation in subseafloor hydrothermal systems on Earth, and on other planets. To better understand the detailed reaction pathways and carbon isotope fractionations in this process under a wide range of physical and chemical conditions, hydrothermal experiments at high temperature (750 C) and pressure (0.55 GPa) were performed using piston cylinder apparatus. Formic acid was used as the source of CO2 and H2, and magnetite was the mineral catalyst. The chemical and carbon isotopic compositions of dissolved organic products were determined by GC-C-MS-IRMS, while organic intermediaries on the mineral catalyst were characterized by Pyrolysis-GC-MS. Among experimental products, dissolved CO2 was the dominant carbon species with a relative abundance of 88 mol%. Dissolved CH4 and C2H6 were also identified with a mole ratio of CH4 over C2H6 of 15:1. No dissolved CO was detected in the experiment, which might be attributable to the loss of H2 through the Au capsule used in the experiments at high temperature and pressure conditions and corresponding conversion of CO to CO2 by the water-gas shift reaction. Carbon isotope results showed that the 13C values of CH4 and C2H6 were -50.3% and -39.3% (V-PDB), respectively. CO2 derived from decarboxylation of formic acid had a (sigma)C-13 value of -19.2%, which was 3.2% heavier than its source, formic acid. The (sigma)C-13 difference between CO2 and CH4 was 31.1%, which was higher than the value of 9.4% calculated from theoretical isotopic equilibrium predictions at experimental conditions, suggesting the presence of a kinetic isotope effect. This number was also higher than the values (4.6 to 27.1%) observed in similar experiments previously performed at 400 C and 50 MPa with longer reaction times. CH4 is 11.0% less enriched in C-13 than C2H6. Alcohols were observed as carbon compounds on magnetite surfaces by Pyrolysis-GC-MS, which confirms the hypothesis regarding the reaction pathways of hydrothermal abiotic organic synthesis proposed by Fu et al. (2007, 2008). In this proposed pathway, hydroxymethylene (-CHOH) groups serve as organic intermediaries on mineral surfaces while dissolved H2 serves as a chain terminator/breaker to generate short chain hydrocarbons and oxygenated compounds. This pathway is different from the carbide polymerization theory of Fischer- Tropsch-type (FTT) synthesis in a gas phase. The observed increase of (sigma)C-13 values of C1 and C2 alkanes with carbon number in our hydrothermal experiments can be readily interpreted by hydroxymethylene pathway, and might be used to differentiate between hydroxymethylene and carbide polymerization pathways. Carbon isotope analysis of alcohols on mineral catalyst surfaces is under way to provide further constraints on formation of organic compounds by FTT in hydrothermal systems.

Fu, Qi↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

NASA NTRS1980

Evaluation of multispectral middle infrared aircraft images for lithologic mapping in the East Tintic Mountains, Utah

Six channels of multispectral middle infrared (8 to 14 micron) aircraft scanner data were acquired over the East Tintic mining district, Utah. This area has high relief and moderate vegetation and consists mainly of Tertiary silicic igneous rocks and Paleozoic quartzite and carbonate rocks that have been locally hydrothermally altered. These digital-image data were computer processed to create a color-composite image based on principal component transformations. Color differences in this image are related to the spectral differences in the surface material and allow discrimination of several rock types, depending primarily on their silica content. When combined with a visible and near infrared color-composite image from a previous flight, with limited field checking, it is possible to discriminate quartzite, carbonate rocks, quartz latitic and quartz monzonitic rocks, latitic and monzonitic rocks, silicified altered rocks, argillized altered rocks, and vegetation.

Kahle, A. B.↗

NASA NTRS2004

Determination of the Three-Dimensional Morphology of ALH84001 and Biogenic MV-1 Magnetite: Comparison of Results from Electron Tomography and Classical Transmission Electron Microscopy

Dated at approximately 3.9 billion years of age, carbonate disks, found within fractures of the host rock of Martian meteorite ALH84001, have been interpreted as secondary minerals that formed at low temperature in an aqueous medium. Heterogeneously distributed within these disks are magnetite nanocrystals that are of Martian origin. Approximately one quarter of these magnetites have morphological and chemical similarities to magnetite particles produced by magnetotactic bacteria strain MV-1, which are ubiquitous in aquatic habitats on Earth. Moreover, these types of magnetite particles are not known or expected to be produced by abiotic means either through geological processes or synthetically in the laboratory. The remaining three quarters of the ALH84001 magnetites are likely products of multiple processes including, but not limited to, precipitation from a hydrothermal fluid, thermal decomposition of the carbonate matrix in which they are embedded, and extracellular formation by dissimilatory Fe-reducing bacteria. We have proposed that the origins of magnetites in ALH84001 can be best explained as the products of multiple processes, one of which is biological. Recently the three-dimensional (3-D) external morphology of the purported biogenic fraction of the ALH84001 magnetites has been the subject of considerable debate. We report here the 3-D geometry of biogenic magnetite crystals extracted from MV-1 and of those extracted from ALH84001 carbonate disks using a combination of high resolution classical and tomographic transmission electron microscopy (TEM). We focus on answering the following questions: (1) which technique provides adequate information to deduce the 3-D external crystal morphology?; and, (2) what is the precise 3-D geometry of the ALH84001 and MV-1 magnetites?

Thomas-Keprta, Kathie L.↗

NASA NTRS2000

Isotope Geochemistry of Possible Terrestrial Analogue for Martian Meteorite ALH84001

We have studied the microdomain oxygen and carbon isotopic compositions by SIMS of complex carbonate rosettes from spinel therzolite xenoliths, hosted by nepheline basanite, from the island of Spitsbergen (Norway). The Quaternary volcanic rocks containing the xenoliths erupted into a high Arctic environment and through relatively thick continental crust containing carbonate rocks. We have attempted to constrain the sources of the carbonates in these rocks by combined O-18/O-16 and C-13/C-12 ratio measurements in 25 micron diameter spots of the carbonate and compare them to previous work based primarily on trace-element distributions. The origin of these carbonates can be interpreted in terms of either contamination by carbonate country rock during ascent of the xenoliths in the host basalt, or more probably by hydrothermal processes after emplacement. The isotopic composition of these carbonates from a combined delta.18O(sub SMOW) and delta.13C(sub PDB) standpoint precludes a primary origin of these minerals from the mantle. Here a description is given of the analysis procedure, standardization of the carbonates, major element compositions of the carbonates measured by electron microprobe, and their correlated C and O isotope compositions as measured by ion microprobe. Since these carbonate rosettes may represent a terrestrial analogue to the carbonate "globules" found in the martian meteorite ALH84001 interpretations for the origin of the features found in the Spitsbergen may be of interest in constraining the origin of these carbonate minerals on Mars.

Mojzsis, Stephen J.↗

DOE OSTI2026

Carbon nanodot precursors enable ultrahigh-loading copper single-atom catalysts for oxygen reduction reaction

Single-atom catalysts (SACs) have attracted significant attention in electrocatalysis due to their high metal utilization and tunable electronic structures; however, their practical implementation is often limited by poor atomic dispersion, low metal loadings (typically < 1 wt%), and insufficient anchoring of single metal atoms on catalyst supports. Herein, we report a simple and versatile strategy to synthesize copper single-atom catalysts (Cu-SACs) with ultrahigh metal loading using citric-acid-derived carbon nanodots as metal-capturing precursors. Through hydrothermal treatment followed by pyrolysis in the presence of urea, atomically dispersed copper atoms coordinated with nitrogen are incorporated into a carbon framework, achieving a Cu loading of up to 20 wt% while maintaining atomic dispersion. Notably, a significant fraction of the copper single atoms exists as Cu+–N2 coordination, which provides under-coordinated and catalytically active sites. The resulting Cu-SAC exhibits promising oxygen reduction reaction (ORR) activity in alkaline media, delivering a limiting current density comparable to that of commercial 20 wt% Pt/C with a predominant four-electron reduction pathway. Despite this high intrinsic activity, durability tests reveal gradual performance degradation under prolonged electrochemical operation, which is attributed to demetallation and aggregation of copper single atoms into metallic nanoparticles. These results demonstrate the potential of carbon nanodot-based platforms for synthesizing high-loading SACs, while underscoring the critical need to simultaneously control carbon porosity and metal–nitrogen coordination to enhance active-site accessibility and durability.

Sharma, Prakhar [University of Kentucky]↗

DOE OSTI2021

Hydrothermal corrosion of laser printed SiC fibers under extreme environment

We report SiC/SiC fiber composites are proposed cladding materials to improve the accident tolerance of commercial light water nuclear reactor fuel. To evaluate their viability, understanding the kinetics of corrosion under irradiation and high-temperature, high-pressure aqueous environment is critical. In the present work, the microstructure and mechanical properties of novel SiC fibers manufactured by Laser Chemical Vapor Deposition (LCVD) are introduced. The LCVD technology has control over microstructure and stoichiometry while allowing for high purity manufacturing, all key qualities needed in search of an optimum SiC fiber for nuclear energy applications. The isolated hydrothermal corrosion of commercially available carbon-rich Hi-Nicalon Type-S fibers is compared to the LCVD stoichiometric and LCVD silicon-rich fibers. Autoclave testing was carried out at 310°C and 14 MPa in the absence of irradiation. In a separate study, the effect of gamma irradiation on the fibers in the room-temperature environment was analyzed. It was observed from the experiments that the dissolution of the fibers was highly dependent on the stoichiometric ratio, fiber surface morphology and thermal pre-treatment of fibers. Contrary to previous findings, fiber dissolution was also visible under low-temperature gamma irradiation in aqueous environment with LCVD fibers showing lower dissolution.

36 MATERIALS SCIENCE↗

NASA NTRS1987

Low temperature hydrothermal maturation of organic matter in sediments from the Atlantis II Deep, Red Sea

Hydrocarbons and bulk organic matter of two sediment cores within the Atlantis II Deep are analyzed, and microbial inputs and minor terrestrial sources are found to represent the major sedimentary organic material. Results show that extensive acid-catalyzed reactions are occurring in the sediments, and the Atlantis II Deep is found to exhibit a lower degree of thermal maturation than other hydrothermal or intrusive systems. The lack of carbon number preference noted among the n-alkanes suggests that the organic matter of these sediments has undergone some degree of catagenesis, though yields of hydrocarbons are much lower than those found in other hydrothermal areas, probably due to the effect of lower temperature and poor source-rock characteristics.

Simoneit, Bernd R. T.↗

DOE OSTI2022

Creation of hollow silica-fiberglass soft ceramics for thermal insulation

Hollow-structured materials show promise in thermal insulation because the shells encapsulating gaseous voids can interrupt heat transport pathways. Here, in this study, we present two low-cost routes to fabricate hollow silica nanoshells, via gas-phase and liquid-phase methods. The gas-phase synthesis method generates hollow shells by a droplet surface precipitation mechanism in a flame aerosol reactor. The liquid-phase synthesis route forms hollow shells by removal of a carbon template, which is produced by hydrothermal reaction of glucose. Both approaches (gas- and liquid-phase) provide hollow silica with amorphous structure, low thermal conductivity (0.023 and 0.026 W m –1 K –1 ), small particle size (442 and 383 nm), thin shell (35 and 36 nm), and low density (0.015 and 0.033 g cm –3 ). We employed high shear mechanical mixing to fabricate hollow silica-fiberglass composite ceramics. The resulting three-dimensional network provides the ceramics with robust mechanical elasticity and fire-retardancy while maintaining low thermal conductivity, dramatically outperforming an analogous material using commercial silica gel in place of the hollow nanoshells. Our findings provide two practical routes to synthesize hollow silica, either of which can be used to manufacture a class of hollow shell-fiber nanocomposite soft ceramics for energy-saving applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Evaluation of Engineered Barrier Systems FY20 Report

This report describes research and development (R&D) activities conducted during fiscal year 2020 (FY20) specifically related to the Engineered Barrier System (EBS) R&D Work Package in the Spent Fuel and Waste Science and Technology (SFWST) Campaign supported by the United States (U.S.) Department of Energy (DOE). The R&D activities focus on understanding EBS component evolution and interactions within the EBS, as well as interactions between the host media and the EBS. A primary goal is to advance the development of process models that can be implemented directly within the Generic Disposal System Analysis (GDSA) platform or that can contribute to the safety case in some manner such as building confidence, providing further insight into the processes being modeled, establishing better constraints on barrier performance, etc. The FY20 EBS activities involved not only modeling and analysis work, but experimental work as well. Despite delays to some planned activities due to COVID-19 precautions, progress was made during FY20 in multiple research areas and documented in this report as follows: (1) EBS Task Force: Task 9/FEBEX Modeling Final Report: Thermo-Hydrological Modeling with PFLOTRAN, (2) preliminary sensitivity analysis for the FEBEX in-situ heater test, (3) cement-carbonate rock interaction under saturated conditions: from laboratory to modeling, (4) hydrothermal experiments, (5) progress on investigating the high temperature behavior of the uranyl-carbonate complexes, (6) in-situ and electrochemical work for model validation, (7) investigation of the impact of high temperature on EBS bentonite with THMC modeling, (8) sorption and diffusion experiments on bentonite, (9) chemical controls on montmorillonite structure and swelling pressure, (10) microscopic origins of coupled transport processes in bentonite, (11) understanding the THMC evolution of bentonite in FEBEX-DP—coupled THMC modeling, (12) modeling in support of HotBENT, an experiment studying the effects of high temperatures on clay buffers/near-field, and (13) high temperature heating and hydration column test on bentonite.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS2008

Detection of Abiotic Methane in Terrestrial Continental Hydrothermal Systems: Implications for Methane on Mars

The recent detection of methane in the Martian atmosphere and the possibility that its origin could be attributed to biological activity, have highlighted the importance of understanding the mechanisms of methane formation and its usefulness as a biomarker. Much debate has centered on the source of the methane in hydrothermal fluids, whether it is formed biologically by microorganisms, diagenetically through the decomposition of sedimentary organic matter, or inorganically via reduction of CO2 at high temperatures. Ongoing research has now shown that much of the methane present in sea-floor hydrothermal systems is probably formed through inorganic CO2 reduction processes at very high temperatures (greater than 400 C). Experimental results have indicated that methane might form inorganically at temperatures lower still, however these results remain controversial. Currently, methane in continental hydrothermal systems is thought to be formed mainly through the breakdown of sedimentary organic matter and carbon isotope equilibrium between CO2 and CH4 is thought to be rarely present if at all. Based on isotopic measurements of CO2 and CH4 in two continental hydrothermal systems, we suggest that carbon isotope equilibration exists at temperatures as low as 155 C. This would indicate that methane is forming through abiotic CO2 reduction at lower temperatures than previously thought and could bolster arguments for an abiotic origin of the methane detected in the martian atmosphere.

Socki, Richard A.↗

DOE OSTI2020

Ring-opening and hydrodenitrogenation of indole under hydrothermal conditions over Ni, Pt, Ru, and Ni-Ru bimetallic catalysts

Here, the activity and selectivity of activated-carbon-supported Ni, Pt, Ru, and Ni-Ru bimetallic catalysts was examined for hydrothermal denitrogenation of indole. The molar yield of pyrrole ring-opening compounds, without an added hydrogen source, are in the order: Ni < Pt < Ni 90 Ru 10 < Ni 75 Ru 25 < Ni 50 Ru 50 ~ Ni 25 Ru 75 ~ Ru. Ru-containing catalysts facilitated production of hydrocarbons (hydrodenitrogenation (HDN) products) when used with added formic acid (hydrogen source). We elucidated catalytic hydrothermal HDN pathways for indole based on the product distributions and the variation of their yields with time. Hydrogenation of indole to indoline is the primary pathway and ring-opening of indoline to form alkyl anilines is faster than forming HDN products (alkyl benzenes). DFT calculations confirmed experimental activity trends, showing Ru is more active than Ni for indole ring opening and for o-toluidine deamination. If no hydrogen source is present, directly breaking the N-C bond in the pyrrole ring is more favorable than breaking the C-N bond with an aromatic carbon. If a H source is provided, the pyrrole ring hydrogenates first, forming indoline, followed by cleavage of the C-N bond.

42 ENGINEERING↗

NASA NTRS2003

Survey for Life-related Species During a Planetary Surface Exploration; System Type I - UV Stimulated Fluorescent Sensor

The widely accepted minimum requirements for life on Earth include the presence of water and accessible sources of carbon. We assume that the same criteria must hold for putative life on past or present Mars. The evidence for CO2 and H2O at or near the Martian surface, carbon in Martian meteorites, aqueous alteration, and probable hydrothermal activity suggest that conditions conducive to the origin and evolution of life on Mars may have existed for long periods of time and may still obtain at present. Surface exploration on Mars that enables the direct detection of water in minerals and of organic carbon (including not just organic and biogenic materials but their degradation products such as kerogen-like hydrocarbons and graphitized carbon) that might be products or residues of biologic activity, is crucial. The search for evidence of life, past or present, will nevertheless be difficult. The lack of direct evidence for organic carbon and the low amounts of water found in the soils at the Viking sites demonstrated the difficulties. Recent results of GRS experiment of Odyssey mission indicated the existence of abundant water ice beneath the Mars surface. Mineralogical evidence for the presence of carbonate, sulfates, or clay minerals, products of weathering and aqueous deposition, have not been identified unambiguously on Mars. Rocks such as shales and, more particularly, limestones, which we associate with moist and benign environments on Earth, are evidently not abundant. Presumably, then, neither were the photosynthetic organisms that might have produced them. In addition, the harsh present environment on Mars (e.g., dryness, low temperatures, large temperature cycles, high level of UV light on the surface, frequent dust storms, etc.) can both destroy carbon- and water-bearing materials and hide them. Therefore, directly detecting life-related materials on Mars was likened to seeking and examining proverbial needles in haystacks. We argue that survey type instruments, that can frequently and quickly check a relatively large amount of material at many locations during a mission, are essential.

Wang, Alian↗

NASA NTRS2004

The Water-Wheel IR (WIR): A Contact Survey Experiment for Water and Carbonates on Mars

Minimum requirements for life include water and accessible carbon. Mars has both in its polar caps and atmosphere. Water (or water-equivalent hydrogen) is present at shallow depths (approx. 10-20 cm) at latitudes =60 and is heterogeneously distributed in other parts of Mars [1]. Mars may have once had surface water that could plausibly have produced carbonate deposits [2-5]. Mars shows signs of hydrothermal activity [6-8] that may have affected soil composition [9, 10]. The Thermal Emission Spectrometer on the Mars Global Surveyor found large and small patches of hematite that may have been water-borne or water-derived [11, 12]. Current orbiting spacecraft (MGS & Odyssey) have not found massive carbonate deposits, however [13]. Shales and limestones, which we associate with moist and benign environments on Earth, are apparently not abundant on Mars. Both carbonate and organic carbon occur as alteration products in Martian meteorites of igneous origin [14]. One study of MGS-TES data suggests 2-5 wt% carbonates (mainly MgCO3) in surface dust, but found no concentrated source [15]. Carbonates and H2O/OH bearing minerals will be sought by the mini-TES and Mossbauer experiments on the Mars Exploration Rovers, one of which landed successfully on Mars on January 3.

Wang, Alian↗

DOE OSTI2024

High mass loading potassium ion stabilized manganese dioxide nanowire forests for rechargeable Zn batteries

Manganese dioxide (MnO 2 ) represents an ideal cathode material for rechargeable aqueous Zn batteries due to its high theoretical capacity (308 mAh g -1 ), suitable potential (1.4 V vs. Zn 2+ /Zn), natural abundance, and negligible toxicity. However, the capacity and rate capability of MnO 2 deteriorate significantly in thick electrodes owing to its low electrical and ionic conductivities. Herein, we report the design of high mass loading potassium ion stabilized α-MnO 2 (K 0.133 MnO 2 ) nanowire forests on carbon cloth through a seed-assisted hydrothermal method for Zn batteries. Further, the vertically aligned K 0.133 MnO 2 nanowire forests with uninterrupted charge transport afford a high area capacity of 3.54 mAh cm -2 and a capacity retention of 79.2% over 1000 cycles in aqueous electrolyte. Moreover, the high area capacity and cyclability can be readily transferred to quasi-solid-state devices.

25 ENERGY STORAGE↗

DOE OSTI2020

Improving Electronic Conductivity of Layered Oxides through the Formation of Two-Dimensional Heterointerface for Intercalation Batteries

Synthetic strategies for the improvement in electronic conductivities and electrochemical stabilities of transition metal oxide cathodes, which are limiting factors in the performance of commercial intercalation batteries, are required for next-generation, high-performance battery systems. Furthermore, the chemical preintercalation approach, consisting of a combined sequence of a sol–gel process, extended aging, and a hydrothermal treatment, is a versatile, wet synthesis technique that allows for the incorporation of a polar species between the layers of transition metal oxides. Here, formation of a layered 2D δ-C x V 2 O 5 · n H 2 O heterostructure occurs via chemical preintercalation of dopamine molecules between bilayers of vanadium oxide followed by the hydrothermal treatment of the precipitate, leading to carbonization of the organic molecules. The presence of carbon layers within the structure has been confirmed via a combined analysis of scanning electron microscopy, X-ray diffraction, thermogravimetric analysis, Raman spectroscopy, X-ray photoelectron spectroscopy, electrochemical impedance spectroscopy, four-probe conductivity measurements, and scanning transmission electron microscopy characterization. 2D δ-C x V 2 O 5 · n H 2 O heterostructure electrodes demonstrated significantly improved electrochemical performance, particularly at higher current densities, in Li-ion cells. The heterostructure electrodes exhibited 75% of the capacity retention when the current was changed from 20 mA g –1 (206 mAh g –1 ) to 300 mA g –1 (155 mAh g –1 ), while the reference δ-V 2 O 5 · n H 2 O electrodes exhibited only 10% capacity retention in the same experiment. Remarkably, 2D δ-C x V 2 O 5 · n H 2 O heterostructure electrodes demonstrated significantly improved capacity retention (94% after 30 cycles) for bilayered vanadium oxide electrodes in Li-ion cells during galvanostatic cycling at 20 mA g –1 . The improved electrochemical performance, in both extended cycling and rate capability studies, of the 2D δ-C x V 2 O 5 · n H 2 O heterostructure electrodes in the Li-ion system is ascribed to the intermittent formation of carbon layers within the bilayered structure, which leads to increased electronic conductivity and improved structural stability of the heterostructure compared to the reference δ-V 2 O 5 · n H 2 O electrodes.

25 ENERGY STORAGE↗