Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ignition probability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Computer program for prediction of capture maneuver probability for an on-off reaction controlled upper stage

A FORTRAN coded computer program which computes the capture transient of a launch vehicle upper stage at the ignition and/or separation event is presented. It is for a single degree-of-freedom on-off reaction jet attitude control system. The Monte Carlo method is used to determine the statistical value of key parameters at the outcome of the event. Aerodynamic and booster induced disturbances, vehicle and control system characteristics, and initial conditions are treated as random variables. By appropriate selection of input data pitch, yaw and roll axes can be analyzed. Transient response of a single deterministic case can be computed. The program is currently set up on a CDC CYBER 175 computer system but is compatible with ANSI FORTRAN computer language. This routine has been used over the past fifteen (15) years for the SCOUT Launch Vehicle and has been run on RECOMP III, IBM 7090, IBM 360/370, CDC6600 and CDC CYBER 175 computers with little modification.

Knauber, R. N.↗

DNS of spark ignition and edge flame propagation in turbulent droplet-laden mixing layers

A parametric study of forced ignition at the mixing layer between air and air carrying fine monosized fuel droplets is done through one-step chemistry direct numerical simulations to determine the influence of the size and volatility of the droplets, the spark location, the droplet-air mixing layer initial thickness and the turbulence intensity on the ignition success and the subsequent flame propagation. The propagation is analyzed in terms of edge flame displacement speed, which has not been studied before for turbulent edge spray flames. Spark ignition successfully resulted in a tribrachial flame if enough fuel vapour was available at the spark location, which occurred when the local droplet number density was high. Ignition was achieved even when the spark was offset from the spray, on the air side, due to the diffusion of heat from the spark, provided droplets evaporated rapidly. Large kernels were obtained by sparking close to the spray, since fuel was more readily available. At long times after the spark, for all flames studied, the probability density function of the displacement speed was wide, with a mean value in the range 0.55-0.75S{sub L}, with S{sub L} the laminar burning velocity of a stoichiometric gaseous premixed flame. This value is close to the mean displacement speed in turbulent edge flames with gaseous fuel. The displacement speed was negatively correlated with curvature. The detrimental effect of curvature was attenuated with a large initial kernel and by increasing the thickness of the mixing layer. The mixing layer was thicker when evaporation was slow and the turbulence intensity higher. However, high turbulence intensity also distorted the kernel which could lead to high values of curvature. The edge flame reaction component increased when the maximum temperature coincided with the stoichiometric contour. The results are consistent with the limited available experimental evidence and provide insights into the processes associated with ignition of practical spray flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Progress in the development of the MARBLE platform for studying thermonuclear burn in the presence of heterogeneous mix on OMEGA and the National Ignition Facility

Mix of ablator material into fuel of an ICF capsule adds non-burning material, diluting the fuel and reducing burn. The amount of the reduction is dependent in part on the morphology of the mix. A probability distribution function (PDF) burn model has been developed [6] that utilizes the average concentration of mixed materials as well as the variance in this quantity across cells provided by the BHR turbulent transport model [3] and its revisions [4] to describe the mix in terms of a PDF of concentrations of fuel and ablator material, and provides the burn rate in mixed material. Work is underway to develop the MARBLE ICF platform for use on the National Ignition Facility in experiments to quantify the influence of heterogeneous mix on fusion burn. This platform consists of a plastic (CH) capsule filled with a deuterated plastic foam (CD) with a density of a few tens of milligrams per cubic centimeter, with tritium gas filling the voids in the foam. This capsule will be driven using x-ray drive on NIF, and the resulting shocks will induce turbulent mix that will result in the mixing of deuterium from the foam with the tritium gas. In order to affect the morphology of the mix, engineered foams with voids of diameter up to 100 microns will be utilized. The degree of mix will be determined from the ratio of DT to DD neutron yield. As the mix increases, the yield from reactions between the deuterium of the CD foam with tritium from the gas will increase. Lastly, the ratio of DT to DD neutrons will be compared to a variation of the PDF burn model that quantifies reactions from initially separated reactants.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Computational fluid dynamics modeling and analysis of silica nanoparticle synthesis in a flame spray pyrolysis reactor

Flame Spray Pyrolysis (FSP) is a method for large-scale production of nanoparticles and nanoscale powders employed in a wide range of industrial applications. Particle size and morphology are complex functions of the physicochemical phenomena occurring in the FSP reactor. An extensive study of FSP-related phenomena can be utilized to develop effective strategies for achieving desired particle size/morphology and scaling up the overall yield of an FSP system. In this work, a computational fluid dynamics (CFD) model of an FSP reactor is developed to simulate the coupling of key phenomena involved in the particle synthesis process: liquid spray breakup and evaporation, mixing, combustion, and particle formation/growth of silica nanoparticles. Herein, the particle sizes and their distributions from the CFD simulations are validated against experimental data. Subsequently, the simulations are utilized to investigate the impact of process parameters on the resultant flame dynamics and particle growth. Firstly, the CFD results show that the particle sizes are strongly correlated with the precursor concentration in the solvent. At lower precursor concentrations, the spread of the distribution is relatively insensitive to the value of the concentration. At higher concentrations, the spread is higher as the collision probability between particles is higher. Secondly, increasing the pilot flow rate increases the length of the pilot flames impacting the local ignition location of the spray flame. Lastly, it is shown that the dispersion gas flow rate strongly influences the spray flame shape. This shape can be used for control of particle growth as it helps determine the regions of high temperature and the residence time of the particles in the high temperature region enabling the design and process optimization of the FSP reactor.

42 ENGINEERING↗

Testing metals and alloys for use in oxygen systems

When oxygen is present in high concentrations or large quantities, as in oxygen-based life-support systems, the likelihood of combustion and the probable intensity of a conflagration increase, together with the severity of the damage caused. Even stainless steel will burn vigorously when ignited in a 1000-psi oxygen environment. The hazards involved in the use of oxygen increase with system operation at the elevated temperatures typical of propulsion systems. Fires in oxygen systems are generally catastrophic, causing a threat to life in manned vehicles. When mechanical components of a mechanism generate friction heat in the presence of oxygen, many commonly used metal alloys ignite and burn. Attention is presently given to frictional heating, particle impact, and flame propagation tests conducted in oxygen environments.

Stoltzfus, Joel M.↗

Sensible-Enthalpy-Based Conditional Moment Closure Model for Homogeneous Charge Compression Ignition with Temperature Inhomogeneity

Abstract This paper presents a sensible-enthalpy-based conditional moment closure (CMC) model for homogeneous charge compression ignition (HCCI) with temperature inhomogeneity. The focus of study is placed on the effects of a conditioning variable on the prediction of heat release rates and developing the mixing models for sensible enthalpy, a reacting scalar. The sensible-enthalpy-based CMC model is validated a priori with 2-D direct numerical simulation (DNS) data for HCCI, and compared with the total-enthalpy-based formulation. Sensible enthalpy is shown to be strongly correlated with temperature, which makes sensible enthalpy well suited for a conditioning variable in CMC for HCCI. Results show that sensible-enthalpy-based CMC performs well for the prediction of heat release rates for all temperature stratification levels investigated in this study, while total-enthalpy-based CMC leads to the overprediction of heat release rates when the temperature stratification level is high. While conditional fluctuations of species mass fractions are substantial, sensible-enthalpy-based CMC is found to accurately estimate heat release rates during ignition, as well as reaction rates of key species, due to substantially suppressed conditional temperature fluctuations. The mapping closure models for the probability density function (PDF) and conditional dissipation rates of sensible enthalpy are proposed. The proposed models are found to capture the characteristics of reactive scalar mixing.

42 ENGINEERING↗

Mishaps with Oxygen in NASA Operations

Data from a substantial number of oxygen mishaps obtained from NASA and contractor records are presented. Information from several Air Force records, concerning oxygen accidents involving aircraft operations, are also included. Descriptions of the mishaps and their causes, for both liquid and gaseous oxygen in ground test facilities and space vehicle systems, are given. A number of safety regulations aimed at reducing the accident probability is discussed. The problems related to material compatibility and materials testing are considered, and the limited information on factors affecting the ignition of materials in oxygen is presented. In addition, details are given of several of the accident/incidents listed in order to define the combination of conditions causing the mishap. In addition to propellant system mishaps, accident/incidents which occurred in space and ground system structures were included, as well as those in electrical systems, ground support facilities, ordnance, and related operations.

Ordin, Paul M.↗

Modeling Forest Understory Fires in an Eastern Amazonian Landscape

Forest understory fires are an increasingly important cause of forest impoverishment in Ammonia, but little is known of the landscape characteristics and climatic phenomena that determine their occurrence. We developed empirical functions relating the occurrence of understory fires to landscape features near Paragominas, a 35- yr-old ranching and logging center in eastern Ammonia. An historical sequence of maps of forest understory fire was created based on field interviews With local farmers and Landsat TM images. Several landscape features that might explain spatial variations in the occurrence of understory fires were also mapped and co-registered for each of the sample dates, including: forest fragment size and shape, forest impoverishment through logging and understory fires, source of ignition (settlements and charcoal pits), roads, forest edges, and others. The spatial relationship between forest understory fire and each landscape characteristic was tested by regression analyses. Fire probability models were then developed for various combinations of landscape characteristics. The analyses were conducted separately for years of the El Nino Southern Oscillation (ENSO), which are associated with severe drought in eastern Amazonia, and non-ENS0 years. Most (91 %) of the forest area that burned during the 10-yr sequence caught fire during ENSO years, when severe drought may have increased both forest flammability and the escape of agricultural management fires. Forest understory fires were associated with forest edges, as reported in previous studies from Ammonia. But the strongest predictor of forest fire was the percentage of the forest fragment that had been previously logged or burned. Forest fragment size, distance to charcoal pits, distance to agricultural settlement, proximity to forest edge, and distance to roads were also correlated with forest understory fire. Logistic regression models using information on fragment degradation and distance to ignition sources accurately predicted the location of lss than 80% of the forest fires observed during the ENSO event of 1997- 1998. In this Amazon landscape, forest understory fire is a complex function of several variables that influence both the flammability and ignition exposure of the forest.

Alencar, A. A. C.↗

Effects of non-thermal termolecular reactions on wedge-induced oblique detonation waves

The shock-induced combustion ramjet (Shcramjet) based on oblique detonation waves (ODWs) is among the promising choices for hypersonic propulsion systems. An understanding of the ignition, propagation, and stability of ODWs is critical to harnessing their propulsive potential. In such high speed reacting flows, there is a high probability of occurrence of non-thermal reactions due to the presence of non-trivial amounts of highly reactive radicals including H, O and OH apart from O 2 as demonstrated recently [M. P. Burke, S. J. Klippenstein, Nat. Chem. 9 (2017) 1078–1082, Y. Tao, A. W. Jasper, Y. Georgievskii, S. J. Klippenstein, R. Sivaramakrishnan, Proc. Combust. Inst. 38 (2021) 515–522]. The present work focuses on examining the initiation, propagation and structure of oblique detonation waves in stoichiometric H 2 -air mixtures through numerical simulations with and without non-thermal reactivity on a two-dimensional adaptive grid. Non-thermal reactions were included in the macroscopic kinetic model as chemically termolecular reactions facilitated by the H + OH radical-radical recombination and the H + O 2 radical-molecule association reactions. Since, the non-thermal reactions result in a corresponding decrease in the reaction fluxes of the incipient recombination/association reactions, an additional simulation was performed by applying corrections to the respective incipient recombination/association rate constants using the methodology demonstrated by Tao et al. [Y. Tao, A. W. Jasper, Y. Georgievskii, S. J. Klippenstein, R. Sivaramakrishnan, Proc. Combust. Inst. 38 (2021) 515–522]. Results show that, under ODWE relevant conditions, non-thermal reactivity fundamentally alters the induction length, intensity as well as the structure of the ODW. Specifically, it is found that non-thermal reactivity leads to a noticeable reduction in initiation length and a simultaneous increase in instantaneous peak heat release rate and the degree of unsteadiness of the ODW. Finally, statistical analysis of key thermo-chemical variables is performed to elucidate the important species as well as reactions responsible for the observed variations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of gravity on halogenated hydrocarbon flame retardant effectiveness

Flammability limits, burning velocities, and minimum ignition energies under initially quiescent conditions were measured for stoichiometric and fuel-lean methane-, ethane-, and propane-air mixtures containing varying concentrations of Halon 1301. The characteristics of near-limit flames were strongly affected by fuel type but not Halon concentration. The conclusions were that the mechanism of the flammability limits was affected by fuel type but not Halon concentration, that the zero-g flammability limit is probably related to a stability criterion which is affected mostly by the molecular diffusion characteristics of the reactant gases and is mostly independent of chemical kinetics, and that the one-g upward flammability and ignition limits provide adequate criteria for safety at one-g and zero-g for both uninhibited and inhibited mixtures.

Ronney, P. D.↗

Effect of gravity on halogenated hydrocarbon flame retardant effectiveness

Flammability limits, burning velocities, and minimum ignition energies under initially quiescent conditions were measured for stoichiometric and fuel-lean methane-, ethane-, and propane-air mixtures containing varying concentrations of Halon 1301. The characteristics of near-limit flames were strongly affected by fuel type but not Halon concentration. The conclusions were that the mechanism of the flammability limits was affected by fuel type but not Halon concentration, that the zero-g flammability limit is probably related to a stability criterion which is affected mostly by the molecular diffusion characteristics of the reactant gases and is mostly independent of chemical kinetics, and that the one-g upward flammability and ignition limits provide adequate criteria for safety at one-g and zero-g for both uninhibited and inhibited mixtures.

Ronney, P. D.↗

Predicting laser-induced bulk damage and conditioning for deuterated potassium di-hydrogen phosphate crystals using ADM (absorption distribution model)

We present an empirical model that describes the experimentally observed laser-induced bulk damage and conditioning behavior in deuterated Potassium dihydrogen Phosphate (DKDP) crystals in a self-consistent way. The model expands on an existing nanoabsorber precursor model and the multi-step absorption mechanism to include two populations of absorbing defects, one with linear absorption and another with nonlinear absorption. We show that this model connects previously uncorrelated small-beam damage initiation probability data to large-beam damage density measurements over a range of ns pulse widths relevant to ICF lasers such as the National Ignition Facility (NIF). In addition, this work predicts the damage behavior of laser-conditioned DKDP and explains the upper limit to the laser conditioning effect. The ADM model has been successfully used during the commissioning and early operation of the NIF.

42 ENGINEERING↗

Prediction of extinction and reignition in nonpremixed turbulent flames using a flamelet/progress variable model. 2. Application in LES of Sandia flames D and E

An extension of the flamelet/progress variable (FPV) model for the prediction of extinction and reignition is applied in large-eddy simulation (LES) of flames D and E of the Sandia piloted turbulent jet flame series. This model employs a presumed probability density function (PDF), in which the marginal PDF of a reactive scalar is modeled by a statistically most likely distribution. This provides two advantages. First of all, the shape of the distribution depends on chemical and mixing time-scale information, and second, an arbitrary number of moments can be enforced. This model was analyzed in an a priori study in the first part of this work. In the present LES application, the first two moments of mixture fraction and reaction progress variable are used to constrain the shape of the presumed PDF. Transport equations for these quantities are solved, and models for the residual scalar dissipation rates, which appear as unclosed terms in the equations for the scalar variances, are provided. Statistical flow field quantities for axial velocity, mixture fraction, and temperature, obtained from the extended FPV model, are in good agreement with experimental data. Mixture-fraction-conditioned data, conditional PDFs, and burning indices are computed and compared with the delta-function flamelet closure model, which employs a Dirac distribution as a model for the marginal PDF of the reaction progress parameter. The latter model considerably underpredicts the amount of local extinction, which shows that the consideration of second-moment information in the presumed PDF of the reaction progress parameter is important for the accurate prediction of extinction and reignition. Mixture-fraction-conditioned results obtained from the extended FPV model are in good agreement with experimental data; however, the overprediction of the consumption of fuel and oxidizer on the fuel-rich side results in an overprediction of minor species. The predictions for the conditional PDFs and burning indices are in good agreement with measurements. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Large eddy simulation of extinction and reignition with artificial neural networks based chemical kinetics

Large eddy simulation (LES) of a non-premixed, temporally evolving, syngas/air flame is performed with special emphasis on speeding-up the sub-grid chemistry computations using an artificial neural networks (ANN) approach. The numerical setup for the LES is identical to a previous direct numerical simulation (DNS) study, which reported considerable local extinction and reignition physics, and hence, offers a challenging test case. The chemical kinetics modeling with ANN is based on a recent approach, and replaces the stiff ODE solver (DI) to predict the species reaction rates in the subgrid linear eddy mixing (LEM) model based LES (LEMLES). In order to provide a comprehensive evaluation of the current approach, additional information on conditional statistics of some of the key species and temperature are extracted from the previous DNS study and are compared with the LEMLES using ANN (ANN-LEMLES, hereafter). The results show that the current approach can detect the correct extinction and reignition physics with reasonable accuracy compared to the DNS. The syngas flame structure and the scalar dissipation rate statistics obtained by the current ANN-LEMLES are provided to further probe the flame physics. It is observed that, in contrast to H{sub 2}, CO exhibits a smooth variation within the region enclosed by the stoichiometric mixture fraction. The probability density functions (PDFs) of the scalar dissipation rates calculated based on the mixture fraction and CO demonstrate that the mean value of the PDF is insensitive to extinction and reignition. However, this is not the case for the scalar dissipation rate calculated by the OH mass fraction. Overall, ANN provides considerable computational speed-up and memory saving compared to DI, and can be used to investigate turbulent flames in a computationally affordable manner. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The time since land-use transition drives changes in fire activity in the Amazon-Cerrado region

Abstract Deforestation and climate change are expected to alter fire regimes along the Cerrado-Amazon transition, one of the world’s most active agricultural frontiers. Here we tested the hypothesis that the time since land-use transition (age of frontier) and agricultural intensification also drive changes in the region’s fire regimes by reducing fire probability in both drought and non-drought years. We modeled fire probability as a function of the time since land-use transitions based on MapBiomas Project datasets from 1986 to 2020. We find that, while burned area declined as pasturelands aged and croplands advanced, deforestation abruptly increased fire activity before (Amazon: 4 years; Cerrado: 3 years) and after (Amazon: 8 years; Cerrado: 7 years) land clearing for pasture, especially in the Amazon. Additionally, the combination of ignition risk, drought, and air-dryness increased the likelihood of large extents of burned areas associated with deforestation. Incorporating frontier age as a proxy for governance in fire modeling is crucial, given the ecological implications of changing fire regimes despite declining rates of fire probability. Most importantly, protecting against deforestation and preserving native vegetation are vital.

Environmental Sciences & Ecology↗

The hydrogen behavior analysis in the water-ingress accident of the 250 MW pebble-bed modular high temperature gas-cooled reactor - 18639

The demonstration power plant of Chinese 250 MW high temperature gas-cooled reactor pebbled-bed module (HTR-PM) which is being under construction in the Shidao Bay of Shandong province has made breakthrough in all of the critical technologies, and is willing to operate in 2017. HTR-PM does not have the risk of large amount of hydrogen generation resulted from the zirconium water reaction due to its special design of graphite core structure and helium coolant of the primary circuit, however, considering that the HTR-PM has a small containment and does not design the deliberate ignitions which is the main hydrogen management measure in light water reactors, it is still necessary to study the hydrogen behavior in the water-ingress accident in which hydrogen will probably be generated. In this paper, the hydrogen generation amount and its distribution in the HTR-PM containment are analyzed with the TINTE code and GASFLOW code respectively in the water ingress accident caused by the steam generator heating tubes rupture. The calculation results indicate that there are total about 16.6 kg and 21 kg hydrogen produced due to graphite corrosion in the typical design basis water ingress accident and beyond design basis accident. The containment sub-pressure ventilation system makes sure the hydrogen concentration in the containment is less than 0.2% during the accident. There is no hydrogen explosion risk in the HTR-PM. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Diagnosing up-scattered deuterium–tritium fusion neutrons produced in burning plasmas at the National Ignition Facility (invited)

In the push to higher performance fusion plasmas, two critical quantities to diagnose are α-heat deposition that can improve and impurities mixed into the plasma that can limit performance. In high-density, highly collisional inertial confinement fusion burning plasmas, there is a significant probability that deuterium–tritium (DT) fusion products, 14.1 MeV neutrons and 3.5 MeV α-particles, will collide with and deposit energy onto (“up-scatter”) surrounding deuterium and tritium fuel ions. These up-scattered D and T ions can then undergo fusion while in-flight and produce an up-scattered neutron (15–30 MeV). These reaction-in-flight (RIF) neutrons can then be uniquely identified in the measured neutron energy spectrum. Further, the magnitude, shape, and relative size of this spectral feature can inform models of stopping-power in the DT plasma and hence is directly proportional to α-heat deposition. In addition, the RIF spectrum can be related to mix into the burning fuel, particularly relevant for high-Z shell and other emerging National Ignition Facility platforms. The neutron time-of-flight diagnostic upgrades needed to obtain this small signal, ~10 –5 times the primary DT neutron peak, will be discussed. Results from several gain > 1 implosions will be shown and compared to previous RIF spectra. Finally, comparisons of experimental data to a simplified computational model will be made.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Oxygen Compatibility Testing of Composite Materials

Composite materials offer significant weight-saving potential for aerospace applications in propellant and oxidizer tanks. This application for oxygen tanks presents the challenge of being oxygen compatible in addition to complying with the other required material characteristics. This effort reports on the testing procedures and data obtained in examining and selecting potential composite materials for oxygen tank usage. Impact testing of composites has shown that most of these materials initiate a combustion event when impacted at 72 ft-lbf in the presence of liquid oxygen, though testing has also shown substantial variability in reaction sensitivities to impact. Data for screening of 14 potential composites using the Bruceton method is given herein and shows that the 50-percent reaction frequencies range from 17 to 67 ft-lbf. The pressure and temperature rises for several composite materials were recorded to compare the energy releases as functions of the combustion reactions with their respective reaction probabilities. The test data presented are primarily for a test pressure of 300 psia in liquid oxygen. The impact screening process is compared with oxygen index and autogenous ignition test data for both the composite and the basic resin. The usefulness of these supplemental tests in helping select the most oxygen compatible materials is explored. The propensity for mechanical impact ignition of the composite compared with the resin alone is also examined. Since an ignition-free composite material at the peak impact energy of 72 ft-lbf has not been identified, composite reactivity must be characterized over the impact energy level and operating pressure ranges to provide data for hazard analyses in selecting the best potential material for liquid tank usage.

Engel, Carl D.↗