Search NASA⌕ Search

SEARCH · Search NASA

Results for “Impurity levels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Inversion of chalcogen defect levels in silicon - An MNDO study

MNDO (modified neglect of diatomic overlap) calculations have been carried out for substitutional oxygen and sulfur impurities in silicon. The calculations of the gap levels reveal a reversal of trend with atomic ionization energies in agreement with self-consistent Green function results, and analysis of the MNDO charge distribution supports the view that the electronegativity difference between oxygen and sulfur gives rise to this shallower energy level.

Singh, R. K.↗
NASA NTRS1986

Quenched-in defects in flashlamp-annealed silicon

Deep levels introduced in boron-doped silicon by heat-pulse annealing with a tungsten-halogen flashlamp are investigated using deep-level transient spectroscopy. Two majority-carrier trapping levels in the band gap, at Ev + 0.32 eV and at Ev + 0.45 eV, are observed. These results are compared to those obtained by furnace-quenching and laser-annealing studies. Both the position in the gap and the annealing kinetics of the hole trap at Ev + 0.45 eV suggest that this center is due to an interstitial iron impurity in the lattice. The deep levels are not consistently observed in all flashlamp-annealed Si crystals utilized.

Borenstein, J. T.↗
NASA NTRS1988

Determination of electron density and temperature in non-LTE plasmas from spectral lines of impurity ions

A novel approach for calculating the populations of the excited Li-like ions C IV, N V, O VI, and Ne VIII is presented. The populations of the 2(2P), 3(2S), 3(2P), and 3(2D) electronic levels in these ions in optically thin plasmas with a broad range of electron density, N(e), and temperature, T(e), are determined from the collisional-radiative model by solving the system of rate equations for the production of excited ions; the equations are linear with respect to the excited ion populations, and the N(e) and T(e) are taken as independent variables. These populations are used to determine the ratios of line intensities for dipole allowed transitions between various energy levels. This approach can be applied to impurities other than the lithiumlike ions and is especially useful for diagnostics of systems where nonintrusive spectroscopic techniques must be used.

Kunc, Joseph A.↗
NASA NTRS2009

Modern Material Analysis Instruments Add a New Dimension to Materials Characterization and Failure Analysis

Modern analytical tools can yield invaluable results during materials characterization and failure analysis. Scanning electron microscopes (SEMs) provide significant analytical capabilities, including angstrom-level resolution. These systems can be equipped with a silicon drift detector (SDD) for very fast yet precise analytical mapping of phases, as well as electron back-scattered diffraction (EBSD) units to map grain orientations, chambers that admit large samples, variable pressure for wet samples, and quantitative analysis software to examine phases. Advanced solid-state electronics have also improved surface and bulk analysis instruments: Secondary ion mass spectroscopy (SIMS) can quantitatively determine and map light elements such as hydrogen, lithium, and boron - with their isotopes. Its high sensitivity detects impurities at parts per billion (ppb) levels. X-ray photo-electron spectroscopy (XPS) can determine oxidation states of elements, as well as identifying polymers and measuring film thicknesses on coated composites. This technique is also known as electron spectroscopy for chemical analysis (ESCA). Scanning Auger electron spectroscopy (SAM) combines surface sensitivity, spatial lateral resolution (10 nm), and depth profiling capabilities to describe elemental compositions of near and below surface regions down to the chemical state of an atom.

Panda, Binayak↗
NASA NTRS1980

Coal thickness guage using RRAS techniques, parts 2 and 3

Electron magnetic resonance was investigated as a sensing technique for use in measuring the thickness of the layer of coal overlying the rock substrate. The goal is development of a thickness gauge which will be usable for control of mining machinery to maintain the coal thickness within selected bounds. A sensor must be noncontracting, have a measurement range of 6 inches or more, and an accuracy of 1/2 inch or better. The sensor should be insensitive to variations in spacing between the sensor and the surface, the response speed should be adequate to permit use on continuous mining equipment, and the device should be rugged and otherwise suited for operation under conditions of high vibration, moisture, and dust. Finally, the sensor measurement must not be adversely affected by the natural effects occurring in coal such as impurities, voids, cracks, layering, high moisture level, and other conditions that are likely to be encountered.

King, J. D.↗
NASA NTRS1989

Computer analysis of the negative differential resistance switching phenomenon of double-injection devices

By directly solving the semiconductor differential equations for the double-injection (DI) devices involving two interacting deep levels, the authors studied the negative differential resistance switching characteristic and its relationship with the device dimension, doping level, and dependence on the deep impurity profile. Computer simulation showed that although one can increase the threshold voltage by increasing the device length, the excessive holding voltage that would follow would put this device in a very limited application such as pulse power source. The excessive leakage current in the low conductance state also jeopardizes the attempt to use the device for any practical purpose. Unless there are new materials and deep impurities found that have a great differential hole and electron capture cross sections and a reasonable energy bandgap for low intrinsic carrier concentration, no big improvement in the fate of DI devices is expected in the near future.

Shieh, Tsay-Jiu↗
NASA NTRS1989

Alternating gradient photodetector

A far infrared (FIR) range responsive photodetector is disclosed. There is a substrate of degenerate germanium. A plurality of alternating impurity-band and high resistivity layers of germanium are disposed on the substrate. The impurity-band layers have a doping concentration therein sufficiently high to include donor bands which can release electrons upon impingement by FIR photons of energy hv greater than an energy gap epsilon. The high resistivity layers have a doping concentration therein sufficiently low as to not include conducting donor bands and are depleted of electrons. Metal contacts are provided for applying an electrical field across the substrate and the plurality of layers. In the preferred embodiment as shown, the substrate is degenerate n-type (N++) germanium; the impurity-band layers are n+ layers of germanium doped to approximately the low 10(exp 16)/cu cm range; and, the high resistivity layers are n-layers of germanium doped to a maximum of approximately 10(exp)/cu cm. Additionally, the impurity-band layers have a thickness less than a conduction-electron diffusion length in germanium and likely to be in the range of 0.1 to 1.0 micron, the plurality of impurity-bands is of a number such that the flux of FIR photons passing therethrough will be substantially totally absorbed therein, the thickness of the high resistivity layers is such compared to the voltage applied that the voltage drop in each the high resistivity layers controls the occurence of impact ionization in the impurity-band layers to a desired level.

Overhauser, Albert W.↗
NASA NTRS1990

Preliminary analysis of SSME baseline plume emissions

A review of current efforts to establish baseline emission levels from the SSME plume is presented. Recent data obtained under the Optical Plume Anomaly Detector program at the Technology Test Bed at MSFC is examined with an emphasis on interpretation of spectral and temporal features observed during nominal motor operation. In particular, the repeated appearance of Cr, Fe, Mn, Ca, and Li at engine startup and shutdown is discussed, and broadband attenuation due to scattering from water vapor is seen to complicate characterization of baseline levels. Also, emission from the combustion related specie OH, the underlying broadband continuum, and the Na impurity is discussed in relation to changes in Rated Power Level (RPL). Results from a theoretical spectral analysis of engine start-up activity is presented.

Wallace, T. L.↗
NASA NTRS2009

Comparisons of Air Radiation Model with Shock Tube Measurements

This paper presents an assessment of the predictive capability of shock layer radiation model appropriate for NASA s Orion Crew Exploration Vehicle lunar return entry. A detailed set of spectrally resolved radiation intensity comparisons are made with recently conducted tests in the Electric Arc Shock Tube (EAST) facility at NASA Ames Research Center. The spectral range spanned from vacuum ultraviolet wavelength of 115 nm to infrared wavelength of 1400 nm. The analysis is done for 9.5-10.5 km/s shock passing through room temperature synthetic air at 0.2, 0.3 and 0.7 Torr. The comparisons between model and measurements show discrepancies in the level of background continuum radiation and intensities of atomic lines. Impurities in the EAST facility in the form of carbon bearing species are also modeled to estimate the level of contaminants and their impact on the comparisons. The discrepancies, although large is some cases, exhibit order and consistency. A set of tests and analyses improvements are proposed as forward work plan in order to confirm or reject various proposed reasons for the observed discrepancies.

Bose, Deepak↗
NASA NTRS1993

Room temperature degradation of YBa2Cu3O(7-x) superconductors in varying relative humidity environments

An aging study was performed to determine the stability of YBa2Cu3O(7-x) ceramics in humid environments at 20 C. In this study, fired ceramic specimens were exposed to humidity levels ranging from 30.5 to 100 percent for 2-, 4-, and 6-week time intervals. After storage under these conditions, the specimens were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrical resistance measurements. At every storage condition evaluated, the fired ceramics were found to interact with H2O present in the surrounding environment, resulting in the decomposition of the YBa2Cu3O(7-x) phase. XRD data showed that BaCO3, CuO, and Y2BaCuO5 were present after aging and that the peak intensities of these impurity phases increased both with increasing humidity level and with increasing time of exposure. Additionally, SEM analyses of the ceramic microstructures after aging revealed the development of needle-like crystallites along the surface of the test specimens after aging. Furthermore, the superconducting transition temperature T(sub c) was found to decrease both with increasing humidity level and with increasing time of exposure. All the specimens aged at 30.5, 66, and 81 percent relative humidity exhibited superconducting transitions above 80 K, although these values were reduced by the exposure to the test conditions. Conversely, the specimens stored in direct contact with water (100 percent relative humidity) exhibited no superconducting transitions.

Hooker, M. W.↗
NASA NTRS1981

The properties of polycrystalline silicon solar cells with controlled titanium additions

By coupling the results of electrical measurements, such as spectral response, lighted and dark I-V determinations, and deep-level-transient spectroscopy with optical and laser scan photomicroscopy, the effects of grain boundaries and impurities on silicon solar cells were evaluated. Titanium, which produces two deep levels in silicon, degrades cell performance by reducing bulk lifetime and thus cell short-circuit current. Electrically active grain boundaries induce carrier recombination in the bulk and depletion regions of the solar cell. Experimental data imply a small but measurable segregation of titanium into some grain boundaries of the polycrystalline silicon containing high Ti concentration. However, for the titanium-contaminated polycrystalline material used in this study, solar cell performance is dominated by the electrically active titanium concentration in the grains. Microstructural impacts on the devices are of secondary importance

Rohatgi, A.↗
NASA NTRS1975

Effect of impurity doping concentration on solar cell output

Experimental measurements were made of solar cell and related photovoltaic parameters for silicon with high concentrations of dopant impurities. The cell output peaked for doping levels around 10 to the 17th power per cu cm. Independent measurements of diffusion length and open circuit voltage at high doping levels showed severe reductions at concentrations above 10 to the 18th power per cu cm. Theoretical reasons are given to explain these reductions. Indication is given of the problems requiring solution before increased cell output can be achieved at high doping levels.

Iles, P. A.↗
NASA NTRS1980

Experimental and theoretical investigations of the quality factor for N/+/P silicon solar cells

Many N(+)P silicon solar cells made with silicon from different growth techniques have current-voltage relations of the form: I = I(0) (exp(qV/AkT) - 1), where the quality factor A is nonintegral, is greater than 1, and shows a temperature dependence. The dark forward characteristics of such cells have been measured over a range of temperatures and the behavior of the factor A derived from them. Lack of agreement with previous models has led to the development of a new model, in which N(+) conduction electrons tunnel to deep levels near that side, these levels being due to junction contamination by impurities. Electron recombination then occurs with holes thermally assisted into the junction from the P side. This mechanism involves increased I(0) values over those for diffusion diode processes and thus reduces the cell power conversion efficiency.

Garlick, G. F. J.↗
NASA NTRS2001

Impact of Functionally Graded Cylinders: Theory

This final report summarizes the work funded under the Grant NAG3-2411 during the 04/05/2000-04/04/2001 period. The objective of this one-year project was to generalize the theoretical framework of the two-dimensional higher-order theory for the analysis of cylindrical functionally graded materials/structural components employed in advanced aircraft engines developed under past NASA Glenn funding. The completed generalization significantly broadens the theory's range of applicability through the incorporation of dynamic impact loading capability into its framework. Thus, it makes possible the assessment of the effect of damage due to fuel impurities, or the presence of submicron-level debris, on the life of functionally graded structural components. Applications involving advanced turbine blades and structural components for the reusable-launch vehicle (RLV) currently under development will benefit from the completed work. The theory's predictive capability is demonstrated through a numerical simulation of a one-dimensional wave propagation set up by an impulse load in a layered half-plane. Full benefit of the completed generalization of the higher-order theory described in this report will be realized upon the development of a related computer code.

Aboudi, Jacob↗
NASA NTRS2005

Method for Determination of Less Than 5 ppm Oxygen in Sodium Samples

Alkali metals used in pumped loops or heat pipes must be sufficiently free of nonmetallic impurities to ensure long heat rejection system life. Life issues are well established for alkali metal systems. Impurities can form ternary compounds between the container and working fluid, leading to corrosion. This Technical Memorandum discusses the consequences of impurities and candidate measurement techniques to determine whether impurities have been reduced to suf.ciently low levels within a single-phase liquid metal loop or a closed two-phase heat transfer system, such as a heat pipe. These techniques include the vanadium wire equilibration, neutron activation analysis, plug traps, distillation, and chemical analysis. Conceptual procedures for performing vanadium wire equilibration purity measurements on sodium contained in a heat pipe are discussed in detail.

Reid, R. S.↗
NASA NTRS1996

Repartitioning of NaCl and Protein Impurities in Lysozyme Crystallization

Nonuniform precipitant and impurity incorporation in protein crystals can cause lattice strain and, thus, possibly decrease the X-ray diffraction resolution. To address this issue, a series of crystallization experiments were carried out, in which initial supersaturation, NaCl concentration, protein purity level and crystallized fraction were varied. Lysozyme and protein impurities, as well as sodium and chloride were independently determined in the initial solution, supernatant and crystals. The segregation coefficients for Na(+) and Cl(-) were found to be independent of supersaturation and NaCl concentration, and decreased with crystallized fraction/crystal size. Numerical evaluation of the extensive body of data, based on a nucleation-growth- repartitioning model, suggests a core of approx. 40 microns in which salt is incorporated in much greater concentrations than during later growth. Small crystals containing higher amounts of incorporated NaCl also had higher protein impurity contents. This suggests that the excess salt is associated with the protein impurities in the core. X-ray topography revealed strain fields in the center of the crystals comparable in size to the inferred core. The growth rates of crystals smaller than 30-40 pm in size were consistently 1.5-2 times lower than those of larger crystals, presumably due to higher chemical potentials in the core.

Vekilov, Peter G.↗
NASA NTRS1986

Photo Hall-effect characterization of closely compensated Ge:Be

The temperature dependence of the free-carrier concentration in germanium doped with the double acceptor Be has been investigated using the photo Hall-effect technique and found to be strongly temperature dependent when the residual shallow impurities are closely compensated. Close compensation of shallow levels was achieved by controlling the concentration of a beryllium-hydrogen acceptor complex A(Be,H) which is present in crystals grown under a H2 atmosphere. This complex can be removed with high-temperature annealing. An increase of up to two orders of magnitude in free-carrier lifetime as a function of temperature is found to occur between 5 and 11 K in closely compensated material due to the population inversion of ionized centers created by optical pumping.

Germer, T. A.↗
NASA NTRS1990

Survival of carbon grains in shocks

Supernova shocks play a significant part in the life of an interstellar grain. In a typical 10 to the 9th power year lifetime, a grain will be hit by an average of 10 shocks of 100 km s(sup -1) or greater velocity, and even more shocks of lower velocity. Evaluation of the results of this frequent shock processing is complicated by a number of uncertainties, but seems to give about 10 percent destruction of silicate grains and about half that for graphite grains. Because of the frequency of shocking, the mineralogy and sizes of the grain population is predominately determined by shock processing effects, and not by the initial grain nucleation and growth environment. One consequence of the significant role played by interstellar shocks is that a certain fraction (up to 5 percent) of the carbon should be transformed into the diamond phase. Diamond transformation is observed in the laboratory at threshold shock pressures easily obtainable in grain-grain collisions in supernova shocks. Yields for transforming graphite, amorphous carbon, glassy carbon, and other nearly pure carbon solids into diamond are quite high. Impurities up to at least the 10 percent level (for oxygen) are tolerated in the process. The typical size diamond expected from shock transformation agrees well with the observed sizes in the Lewis et al. findings in meteoritic material. Isotropic anomalies already contained in the grain are likely to be retained through the conversion process, while others may be implanted by the shock if the grain is close to the supernova. The meteoritic diamonds are likely to be the results of transformation of carbon grains in grain-grain collisions in supernova shock waves.

Seab, C. Gregory↗