Search NASA⌕ Search

SEARCH · Search NASA

Results for “Intermittent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

The composition of gases from a diffusion flame above longleaf pine needle fuel beds

The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.

Biomass↗
DOE OSTI2023

Organic matter sulfurization and organic carbon burial in the Mesoproterozoic

Throughout the Proterozoic Era, sedimentary organic carbon burial helped set the pace of global oxygenation and acted as a major modulator of atmospheric CO 2 and climate. Although Proterozoic rocks generally contain low concentrations of organic matter (OM), there are key exceptions to this rule, including the relatively OM-rich Arctic Bay shales from Baffin Island, Canada (Bylot Supergroup, Borden Basin, ~1.05 Ga). The mechanisms driving elevated OM concentrations in these and other Proterozoic shales remain poorly understood. In the Mesozoic and Cenozoic, organic matter sulfurization can be a major driver of enhanced OM burial across a range of redox conditions comparable to those inferred for many Proterozoic environments. Therefore, in this study, we evaluate the role of sulfurization in driving OM preservation in the Mesoproterozoic Borden Basin and discuss its relevance to Proterozoic systems in general. We present the first evidence for syngenetic-to-early-diagenetic OM sulfurization in a Proterozoic basin, which begins to fill a several-billion-year gap in our record of organic S across Earth history. We find that OM sulfurization was particularly extensive in shales from a relatively shallow-water section (Alpha River) but less extensive in shales deposited in deeper water (Shale Valley), which is consistent with models that infer sulfidic ‘wedges’ or O 2 -minimum-zone-type structures on shelf margins at least intermittently at this time. At the shallower site, organic S and pyrite are similarly 34 S-depleted and thus likely formed at roughly the same time near the sediment–water interface under conditions previously interpreted to have been ferruginous to intermittently sulfidic. In contrast, at the deeper-water site, large S-isotope differences between pyrite and organic S along with low apparent OM sulfurization intensities indicate that pyrite formation was favored over OM sulfurization during early sedimentation under variable but primarily ferruginous conditions. Although Mesoproterozoic biomass can be substantially sulfurized, indicators of sulfurization intensity are not correlated with OM concentrations, and therefore sulfurization does not appear to have been the primary driver of enhanced OM concentrations in Arctic Bay Formation shales. The link between sulfurization and total OM preservation may have been modulated during the deposition of Arctic Bay Formation shales by differences in iron availability, nutrient cycling, and particle dynamics in the Mesoproterozoic.

58 GEOSCIENCES↗
DOE OSTI2024

Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials

Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Martensitic transformation induced strength-ductility synergy in additively manufactured maraging 250 steel by thermal history engineering

Maraging steels are known for their exceptional strength but suffer from limited work hardening and ductility. Here, in this study, we report an intermittent printing strategy to tailor the microstructure and mechanical properties of maraging 250 steel via tuning the thermal history during wire-arc directed energy deposition. By introducing a dwell time between adjacent layers, the maraging 250 steel is cooled below the martensite start temperature, triggering thermally-driven martensitic transformation during the printing process. Thermal cycling during subsequent layer deposition results in the formation of reverted austenite which shows a refined microstructure and induces elemental segregation between martensite and reverted austenite. The Ni enrichment in the austenite promotes stabilization of the reverted austenite upon cooling to room temperature. The reverted austenite is metastable during deformation, leading to strain-induced martensitic transformation under loading. Specifically, a 3 min interlayer dwell time produces a maraging 250 steel with approximately 8% reverted austenite, resulting in improved work hardening via martensitic transformation induced plasticity during deformation. Meanwhile, the higher cooling rate and refined prior austenite grains lead to substantially refined martensitic grains (by approximately fivefold) together with an increased dislocation density. With 3 min interlayer dwell time, the yield strength of the printed maraging 250 steel increases from 836 MPa to 990 MPa, and the uniform elongation is doubled from 3.2% to 6.5%. This intermittent deposition strategy demonstrates the potential to tune the microstructure of maraging steels for achieving strength-ductility synergy by engineering the thermal history during additive manufacturing.

Additive manufacturing↗
DOE OSTI2021

Contributions of biofilm-induced flow heterogeneities to solute retention and anomalous transport features in porous media

We report that microbial biofilms are ubiquitous within porous media and the dynamics of their growth influence surface and subsurface flow patterns which impacts the physical properties of porous media and large-scale transport of solutes. Here, a two-dimensional pore-scale numerical model was used to evaluate the impact of biofilm-induced flow heterogeneities on conservative transport. Our study integrates experimental biofilm images of Paenibacillus 300A strain in a microfluidic device packed with cylindrical grains in a hexagonal distribution, with mathematical modeling. Biofilm is represented as a synthetic porous structure with locally varying physical properties that honors the impact of biofilm on the porous medium. We find that biofilm plays a major role in shaping the observed conservative transport dynamics by enhancing anomalous characteristics. More specifically, when biofilm is present, the pore structure in our geometry becomes more spatially correlated. We observe intermittent behavior in the Lagrangian velocities that switches between fast transport periods and long trapping events. Our results suggest that intermittency enhances solute spreading in breakthrough curves which exhibit extreme anomalous slope at intermediate times and very marked late solute arrival due to solute retention. The efficiency of solute retention by the biofilm is controlled by a transport regime which can extend the tailing in the concentration breakthrough curves. These results indicate that solute retention by the biofilm exerts a strong control on conservative solute transport at pore-scale, a role that to date has not received enough attention.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Sixty days of head-down tilt bed rest with or without artificial gravity do not affect the neuromuscular secretome

Highlights: • Long-term bed rest with/without artificial gravity does not affect the neuromuscular secretome. • Serum concentrations of markers of muscle wasting are not affected by bed rest/artificial gravity. • C-terminal Agrin Fragment serum concentrations are not affected by bed rest/artificial gravity. • Human centrifugation during bed rest does not have a negative impact on the neuromuscular secretome. Artificial gravity is a potential countermeasure to attenuate effects of weightlessness during long-term spaceflight, including losses of muscle mass and function, possibly to some extent attributable to disturbed neuromuscular interaction. The 60-day AGBRESA bed-rest study was conducted with 24 participants (16 men, 8 women; 33 ± 9 years; 175 ± 9 cm; 74 ± 10 kg; 8 control group, 8 continuous (cAG) and 8 intermittent (iAG) centrifugation) to assess the impact of bed rest with or without daily 30-min continuous/intermittent centrifugation with 1G at the centre of mass. Fasting blood samples were collected before and on day 6, 20, 40 and 57 during 6° head-down tilt bed rest. Concentrations of circulating markers of muscle wasting (GDF-8/myostatin; slow skeletal muscle troponin T; prostaglandin E2), neurotrophic factors (BDNF; GDNF) and C-terminal Agrin Fragment (CAF) were determined by ELISAs. Creatine kinase activity was assessed by colorimetric enzyme assay. Repeated-measures ANOVAs were conducted with TIME as within-subject, and INTERVENTION and SEX as between-subject factors. The analyses revealed no significant effect of bed rest or sex on any of the parameters. Continuous or intermittent artificial gravity is a safe intervention that does not have a negative impact of the neuromuscular secretome.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

Vortical interactions in turbulent thermoacoustic systems

This study examines the dynamics of vortical interactions and their implications for mitigating thermoacoustic instability in a turbulent combustor. The regions of intense vortical interactions are identified as vortical communities in the network space of weighted directed vortical networks constructed from two-dimensional experimental velocity data. One can expect vortical interactions in the combustor to be strongest near the moment of vortex shedding, as the shed vortices gradually weaken due to dissipation while convecting downstream. However, we show that, during the state of thermoacoustic instability, there is a non-trivial consistent phase lag of approximately 52° between the shedding of the coherent structures from the backward-facing step and the time instant when the vortical interactions attain their local maximum value. We explain this phase lag by investigating the correlation between acoustic pressure fluctuations, spatio-temporal dynamics of coherent structures and vortical interactions in the reaction field of the combustor. We also show the aperiodic variation of vortical interactions during the states of combustion noise and aperiodic epochs of intermittency. Furthermore, the spatio-temporal evolution of pairs of vortical communities with the maximum inter-community interactions provides insight into explaining the critical regions detected in the reaction field during the states of intermittency and thermoacoustic instability, also identified in previous studies. As a result, we further show that the most efficient suppression of thermoacoustic instability via air microjet injection is achieved when steady air jets are introduced to disrupt the maximum inter-community interactions present during the state of thermoacoustic instability.

Sahay, Ankit [Indian Institute of Technology Madra↗
DOE OSTI2025

Assessment of Blocking Contacts in Suppressing Polarization Effects in CsPbBr 3 Perovskite Detectors

The CsPbBr 3 perovskite has garnered significant attention as a room-temperature semiconductor for hard radiation detection due to straightforward synthesis, scalable crystal growth, low cost, and excellent energy resolution. However, despite these advantages, at ambient temperature, CsPbBr 3 devices may experience performance deterioration and irreversible failure due to “polarization” induced by electromigration of ions to electrical connections on the device. In this study, we tested several contact materials and their optimization deposition techniques to assess the stability of high-performance CsPbBr 3 γ-ray detectors. Metals, with low work functions (Ti, In, Sn, Sb, Pb, Bi, Al, Au, and TiC) and high-work-function (Au or Pt) contacts, were used to form different Schottky junctions using vacuum thermal evaporation, electron-beam evaporation, and sputtering methods. These detectors were tested in intermittent and continuous modes to assess their stability. Among the tested detectors, the Bi/CLB/Pt electrode configuration demonstrated superior stability, operating effectively for 11 months under periodic testing and 16 days under continuous testing. In contrast, other configurations functioned only for a few months under intermittent conditions. Upon incorporating a ~40-nm-thick TiC passivation layer on the anode side (Bi/TiC/CLB/Pt), the CLB device operated continuously for 36 days without degradation. In many cases, the failure mode of the devices was due to the degradation of the anode. Here, the chemical changes in the fresh and deteriorated anodes were characterized using scanning electron microscopy and energydispersive X-ray spectroscopy

CsPbBr3 perovskite↗
DOE OSTI2024

Europa modifies Jupiter’s 1 plasma sheet

Jupiter's plasma sheet has been understood to be primarily composed of Io-genic sulfur and oxygen, along with protons at lower mass density. These ions move radially away from Jupiter, filling its magnetosphere. The material in the plasma sheet interacts with Europa, which is also a source of magnetospheric pickup ions, primarily hydrogen and oxygen. Juno's thermal plasma instrument JADE, the Jovian Auroral Distributions Experiment, has provided comprehensive in situ observations of the composition of Jupiter's plasma sheet ions with its Time-of-Flight mass-spectrometry capabilities. Here, we present observations of the magnetospheric composition in the Europa-Ganymede region of Jupiter's magnetosphere. We find material from Europa is intermittently present at comparable densities to Io-genic plasma. The intermittency of Europa-genic signatures suggests Europa's neutral oxygen toroidal cloud is more localized to Europa's vicinity than its hydrogen cloud. These observations reveal a more complex and compositionally diverse magnetosphere than previously thought.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

A Probabilistic Model for Global EMIC Wave Activity Using Van Allen Probes Observations

Electromagnetic ion cyclotron (EMIC) waves play a key role in radiation belt dynamics through resonant interactions. However, their low occurrence probability, high variability, and spatial intermittency pose challenges for accurate modeling. In this study, we present a machine learning (ML)-based global EMIC wave model built on the entire data set from the Van Allen Probes mission. To capture the distinct statistical characteristics of wave occurrence and amplitude, the model is separated into two modules: an occurrence model trained using ML techniques, and a wave amplitude model sampled from observed probability distributions. The input parameters are limited to real-time or predictable variables to ensure practical applicability. Our model shows strong performance across the entire test set and demonstrates improved predictive capability over a baseline random occurrence model, particularly during quiet geomagnetic conditions. Evaluation during both quiet and active periods confirms the model's ability to represent the clustered and intermittent nature of EMIC wave activity. Furthermore, the model provides global estimates of wave power, enabling integration with radiation belt electron data and showing signatures consistent with wave-induced scattering. We found a good correlation between the global wave activity from the model and relativistic electron observation by Van Allen Probes, regardless of the availability of in situ wave observations. The modular structure of the model also allows for straightforward expansion for additional wave properties, such as wave frequency, which can be modeled independently. This flexible, event-sensitive approach offers a promising framework for data-driven radiation belt simulations and space weather applications.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Mild-to-wild plastic transition is governed by athermal screw dislocation slip in bcc Nb

Plastic deformation in crystals is mediated by the motion of line defects known as dislocations. For decades, dislocation activity has been treated as a homogeneous, smooth continuous process. However, it is now recognized that plasticity can be determined by long-range correlated and intermittent collective dislocation processes, known as avalanches. Here we demonstrate in body-centered cubic Nb how the long-range and scale-free dynamics at room temperature are progressively quenched out with decreasing temperature, eventually revealing intermittency with a characteristic length scale that approaches the Burgers vector itself. Plasticity is shown to be bimodal across the studied temperature regime, with conventional thermally-activated smooth plastic flow (‘mild’) coexisting with sporadic bursts (‘wild’) controlled by athermal screw dislocation activity, thereby violating the classical notion of temperature-dependent screw dislocation motion at low temperatures. An abrupt increase of the athermal avalanche component is identified at the critical temperature of the material. Our results indicate that plasticity at any scale can be understood in terms of the coexistence of these mild and wild modes of deformation, which could help design better alloys by suppressing one of the two modes in desired temperature windows.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Exogenous electricity flowing through cyanobacterial photosystem I drives CO 2 valorization with high energy efficiency

Nature's biocatalytic processes are driven by photosynthesis, whereby photosystems I and II are connected in series for light-stimulated generation of fuel products or electricity. Externally supplying electricity directly to the photosynthetic electron transfer chain (PETC) has numerous potential benefits, although strategies for achieving this goal have remained elusive. Here we report an integrated photo-electrochemical architecture which shuttles electrons directly to PETC in living cyanobacteria. The cathode of this architecture electrochemically interfaces with cyanobacterial cells that have a lack of photosystem II activity and cannot perform photosynthesis independently. Illumination of the cathode channels electrons from an external circuit to intracellular PETC through photosystem I, ultimately fueling cyanobacterial conversion of CO 2 into acetate. We observed acetate formation when supplying both illumination and exogenous electrons under intermittent conditions (e.g., in a 30 s supply plus 30 min interval condition of both light and exogenous electrons). The energy conversion efficiency for acetate production under programmed intermittent LED illumination (400–700 nm) and exogenous electron supply reached ca. 9%, when taking into account the number of photons and electrons received by the biotic system, and ca. 3% for total photons and electrons supplied to the cyanobacteria. This approach is applicable for generating various CO 2 reduction products by using engineered cyanobacteria, one of which has enabled electrophototrophic production of ethylene, a broadly used hydrocarbon in the chemical industry. The resulting bio-electrochemical hybrid has the potential to produce fuel chemicals with numerous potential advantages over standalone natural and artificial photosynthetic approaches.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Beyond conventional batteries: a review on semi-solid and redox targeting flow batteries-LiFePO{sub 4} as a case study.

Clean and sustainable energy is becoming increasingly crucial to tackle the current energy crisis. However, the intermittent nature of renewable energy sources presents a challenge for their effective implementation. Redox flow batteries (RFBs) have emerged as a promising solution to this problem, as they can help enhance the stability of grid networks and promote the use of renewable energy sources. RFBs are highly modular and scalable systems that can be customized to meet the power and energy requirements of different renewable energy plants. Moreover, they offer several advantages over conventional battery technologies, including cost and safety concerns. However, conventional RFBs have limited energy densities due to the low solubility of their active species in electrolyte. To overcome this limitation, semi-solid (SSRFBs) and redox targeting (RTFBs) flow batteries have been proposed. These systems feature high concentrations of active species and impressive energy densities, making them highly attractive for renewable energy applications. LiFePO4 (LFP) is a highly promising active material for semi-solid and targeting flow batteries. One of the key advantages of LFP is its low raw materials cost, as it is composed of Earth-abundant elements such as iron and phosphorus. This makes it an attractive option for large-scale battery production. The recent developments in SSRFBs and RTFBs using LFP as catholyte hold great promise for the future of sustainable energy storage. The combination of LFP's low cost, safety, durability, and high energy density with the modularity and scalability of flow battery systems make for a compelling solution to the challenges of intermittent renewable energy sources. Ongoing research and development in this area will likely yield even further improvements in the performance and efficiency of LFP-based flow batteries, opening exciting new possibilities for sustainable energy storage.

El Halya, Nabil↗
DOE OSTI2021

High pressure, high flow rate batch mixing apparatus for high throughput experiments

An automated, high pressure, high flow rate batch mixing apparatus has been designed and constructed for rapid, stable, and repeatable mixing of multiple gases and vapors. The apparatus operates as an intermittent batch mixer with cycles of topping off fresh mixture to maintain pressure in an accumulator tank until consumed in an experimental apparatus. At high duty cycles, the apparatus can also function at steady state. This style of mixing is suitable for experiments such as high repetition rate shock tubes and other devices with intermittent flow demands. It is compact and portable, facilitating use in locations such as synchrotron light sources. The entire apparatus is heated to permit the mixing of vapors from species with low volatilities. The apparatus is fully automated and runs for extended periods with the only intervention being to refresh reagent supplies. Here, the accuracy and repeatability of the apparatus were verified by periodic gas sampling and analysis with gas chromatography. Multi-component mixtures spanning a wide range of complexity, dilution, and volatility of constituents have been prepared. The compositions of the majority of the mixture were found to be stable over several filling cycles, repeatable, and with the proper calibration of set-point conditions, accurate. Challenges were encountered preparing a mixture from multi-component liquids, and potential solutions are discussed.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Non-ideal MHD growth of current interchange tearing modes at plasma edge and response to externally-imposed flow

Current interchange tearing modes (CITMs) have been proposed to explain an intermittent eruption of electric current toward a divertor at an edge region of a tokamak device. Extended magnetohydrodynamic (MHD) simulations combined with the Scrape-Off-Layer diffusion model, which has been developed by the authors [Miura et al., Phys. Plasmas 24, 092111 (2017)], are carried out in order to study the growth of a CITM under influences of two-fluid and gyro-viscous effects, or non-ideal MHD effects. Numerical simulations both with and without an externally imposed azimuthal flow show that the growth of a CITM is observed for a relatively small flow velocity, and that a CITM can be a candidate mechanism for the intermittent eruption of the current in a tokamak, whether the growth is under influences of non-ideal MHD effects or not. Here, the growth can be suppressed when an externally imposed azimuthal flow is sufficiently large to cause a finite radial displacement because such a displacement prevents a transition from an interchange to a tearing mode that is the key process of a CITM. Furthermore, it is also found that a stripe pattern similar to so-called streamers is formed in the course of the CITM growth. The basic nature of this streamer-like structure is also presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Scaling Up CSP: How Long Will it Take?

Concentrating solar power (CSP) is one of the few scalable technologies capable of delivering dispatchable renewable power. Therefore, many expect it to shoulder a significant share of system balancing in a renewable electricity future powered by cheap, intermittent PV and wind power: the IEA, for example, projects 73 GW CSP by 2030 and several hundred GW by 2050 in its Net-Zero by 2050 pathway. In this paper, we assess how fast CSP can be expected to scale up and how long time it would take to get new, high-efficiency CSP technologies to market, based on observed trends and historical patterns. We find that to meaningfully contribute to net-zero pathways the CSP sector needs to reach and exceed the maximum historical annual growth rate of 30%/year last seen between 2010-2014 and maintain it for at least two decades. Any CSP deployment in the 2020s will rely mostly on mature existing technologies, namely parabolic trough and molten-salt towers, but likely with adapted business models such as hybrid CSP-PV stations, combining the advantages of higher-cost dispatchable and low-cost intermittent power. New third-generation CSP designs are unlikely to play a role in markets during the 2020s, as they are still at or before the pilot stage and, judging from past pilot-to-market cycles for CSP, they will likely not be ready for market deployment before 2030. CSP can contribute to low-cost zero-emission energy systems by 2050, but to make that happen, at the scale foreseen in current energy models, ambitious technology-specific policy support is necessary, as soon as possible and in several countries.

concentrated solar power↗
DOE OSTI2023

A high-resolution large-eddy simulation framework for wildland fire predictions using TensorFlow

Background: Wildfires are becoming more severe, so we need improved tools to predict them over a wide range of conditions and scales. One approach towards this goal entails the use of coupled fire/atmosphere modelling tools. Although significant progress has been made in advancing their physical fidelity, existing tools have not taken full advantage of emerging programming paradigms and computing architectures to enable high-resolution wildfire simulations. Aims: The aim of this study was to present a new framework that enables landscape-scale wildfire simulations with physical representation of combustion at an affordable cost. Methods: We developed a coupled fire/atmosphere simulation framework using TensorFlow, which enables efficient and scalable computations on Tensor Processing Units. Key Results: Simulation results for a prescribed fire were compared with experimental data. Predicted fire behavior and statistical analysis for fire spread rate, scar area, and intermittency showed overall reasonable agreement. Scalability analysis was performed, showing close to linear scaling. Conclusions: While mesh refinement was shown to have less impact on global quantities, such as fire scar area and spread rate, it benefits predictions of intermittent fire behavior, buoyancy-driven dynamics, and small-scale turbulent motion. Implications: This new simulation framework is efficient in capturing both global quantities and unsteady dynamics of wildfires at high spatial resolutions.

54 ENVIRONMENTAL SCIENCES↗