Search NASA⌕ Search

SEARCH · Search NASA

Results for “LATERAL CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

An in-flight simulation of lateral control nonlinearities

An in-flight simulation program was conducted to explore, in a generalized way, the influence of spoiler-type roll-control nonlinearities on handling qualities. The roll responses studied typically featured a dead zone or very small effectiveness for small control inputs, a very high effectiveness for mid-range deflections, and low effectiveness again for large inputs. A linear force gradient with no detectable breakout force was provided. Given otherwise good handling characteristics, it was found that moderate nonlinearities of the types tested might yield acceptable roll control, but the best level of handling qualities is obtained with linear, aileron-like control.

Ellis, D. R.↗
NASA NTRS1979

Preliminary study of pilot lateral control of two light airplanes near the stall

For two representative light, single-engine airplanes the single-axis piloting task of controlling bank angle with combined aileron and rudder, and a two-axis task of controlling bank angle with aileron and sideslip with rudder have been studied. For these tasks existing divergence criteria have been applied to determine conditions for closed-loop stability for selected flight conditions near the stall; in addition closed-loop stability characteristics and airplane response to bank angle command were calculated. Results obtained from applying the divergence criterion and from calculations of airplane responses to bank angle command indicate that aileron-alone bank angle control is marginally acceptable at high angle of attack. Of the two rudder control techniques considered, rudder used with the aileron in controlling bank angle increasd stability and produced satisfactory responses; the combined bank angle and sideslip control task does not warrant further consideration because of the task difficulty and the small improvement indicated in airplane closed-loop response with this technique.

Moul, M. T.↗
NASA NTRS1990

Aeroservoelastic tailoring for lateral control enhancement

The application of an automated optimization approach to the integrated structural and control design of an aircraft wing and its control surface is illustrated. The performance index or cost function for optimization is the aileron hinge moment required to sustain a specified terminal roll rate at a chosen design speed at which aeroelastic effects are significant. The design variables used for aileron hinge-moment minimization are the aileron flap-to-chord ratio; the location of the aileron with respect to the roll axis; and the orientations of three advanced composite plies comprising 60 percent of the wing structure. The effects of aileron location and advanced composite ply orientation on the terminal roll rate and aileron hinge moment are examined. Optimization is seen to involve a compromise between a laminated structure/aileron combination that is effective in creating large rolling moments and one that minimizes the damping-in-roll. These two requirements are in conflict; the optimization driver must locate a compromise design point by moving the control surface and changing its size while also creating a suitable structural design.

Weisshaar, Terrence A.↗
NASA NTRS1993

Lateral control at high angles of attack using pneumatic blowing through a chined forebody

Directional control through the use of pneumatic blowing was investigated on a generic subscale model with a chined forebody with blowing through a chine slot in a direction normal to the forebody surface. Comparisons are made with a vertical tail on and off, and with control through rudder deflection. Force and moment data were obtained for various blowing coefficients over a 0-75 deg alpha range, and flow visualization was also conducted in order to see qualitative effects on the flowfield. Blowing through a chined forebody generates yaw moments at large alpha where control surfaces lose their effectiveness; these moments are much larger than obtained by jet thrust alone, since the forebody flowfield is modified through the interaction of the jet with the chine vortices. Directional control increased with angle of attack for a given blowing coefficient until a maximum was reached. Further increases in angle of attack results in a rapid loss of effectiveness. For angles of attack above 60 deg, yaw moments are generated by simple jet thrust effect. The effectiveness of the pneumatic system depended on tail configuration.

Arena, A. S., Jr.↗