SEARCH · Search NASA

Results for “Laser beam effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Electromechanical response of piezoelectric thin films subjected to large strain

The use of piezoelectric thin sensors, when subjected to large static strain levels in ultrasonic applications is reported in this paper. A novel flipped beam bending method is proposed to induce static strain level nearing twice the incipient yield strain in the beam material (~0.39%). First, the effect of static large strain on ultrasonic guided wave propagation in the beam was studied using the velocity measurements obtained from a laser Doppler vibrometer. Next, the ultrasonic response of thin sensors is studied under compressive and tensile static strain (±0.72%) with the sensors symmetrically bonded on the lower and upper surfaces, and at the same axial location. The ultrasonic guided wave response to varying levels of static strain is recorded at different center frequencies (50–400 kHz) of the narrow banded ultrasonic excitation. As a case study, the variation of the ultrasonic guided wave response of polyvinylidene difluoride (PVDF) thin sensors with center frequencies at different static strain levels was analyzed and compared with that of lead zirconate titanate (PZT) thin sensors. PZT sensors show a higher variation of sensing performance with strain when compared to PVDF sensors. Apart from static strain, the possible effects on the change in performance of sensors, such as the change in the capacitance is discussed. The characterization method provides a reusable beam arrangement to study the ultrasonic sensor performance at large static strain levels. Characterization at large strain level allows the development of fail-safe sensors even under large strain and permanent plastic deformation of structure on which they are bonded, allowing accurate ultrasonic structural health monitoring even in the presence of damage progression. Piezopolymer sensor like PVDF are least susceptible to static strain due to large yield strain and low modulus and can serve as fail-safe sensors under large strain.

Rathod, Vivek↗

DOE OSTI2022

Air resonance enhanced multiphoton ionization tagging velocimetry

Air resonance enhanced multiphoton ionization (REMPI) tagging velocimetry (ART) was demonstrated in quiescent and supersonic flows. The ART velocimetry method utilizes a wavelength tunable laser beam to resonantly ionize molecular oxygen in air and generate additional avalanche-type ionization of molecular nitrogen. The fluorescence emissions from the first negative and first positive bands of molecular nitrogen are, thus, produced and used for flow tagging. Detailed characterization of ART was conducted, including the effects of oxygen resonance to fluoresce nitrogen, nitrogen fluorescence spectrum, laser energy deposition into quiescent flow showing minimal perturbations in flow, fluorescence lifetime study at various pressures, and line tagging without breakdown. Pointwise velocity measurements within a supersonic flow from a nominal Mach 1.5 nozzle have been conducted and characterized.

Clark, Aleksander↗

DOE OSTI2025

Time-domain thermoreflectance

Time-domain thermoreflectance (TDTR) has been instrumental in measuring the heat transfer properties of bulk and nanostructured materials over the past two decades. In this Primer, we describe the optical and thermal aspects of TDTR, with an in-depth discussion on the theory, apparatus design and implementation. We present examples that illustrate the ability of TDTR to measure thermal conductivity tensors, thermal conductance across material interfaces, and volumetric heat capacity of thin films, 2D materials and bulk materials. The ability of TDTR to spatially resolve thermal properties is useful for studying heterogeneous material systems, such as materials processed in or subjected to extreme environments. We consider current limitations of pump–probe metrologies and discuss recent advancements of TDTR, such as time-resolved magneto-optic Kerr effect (TR-MOKE), beam-offset TDTR/TR-MOKE, steady-state thermoreflectance, frequency-domain thermoreflectance and laser-flash TDTR. Lastly, we present an outlook on anticipated technological developments to further expand the ability of TDTR to measure nanoscale thermal properties.

42 ENGINEERING↗

DOE OSTI2023

GaN MOCVD Growth on Native substrates for High Voltage (15-20 KV) Vertical Power Devices

This project aims to develop metalorganic chemical vapor deposition (MOCVD) homoepitaxy of GaN on native substrates with fast growth rate (15-20 μm/hr), low background doping (low-10 15 cm -3 ) and smooth surface morphology via comprehensive understanding of the crystal growth process including high quality GaN substrate development and surface preparation, impurity and native defects control, and their impacts on the breakdown field. The team successfully developed a new growth process by introducing the laser-assisted MOCVD (LA-MOCVD) process to address the limited growth rates of GaN in the traditional MOCVD process. Specifically, the use of the CO2 laser with lasing wavelength of 9.219 μm, the strong coupling between the laser beam with the ammonia (GaN MOCVD precursor) leads to efficient decomposition of NH3 which significantly increases the effective group V/III molar ratio and thus suppresses C impurity incorporation in MOCVD GaN. The reduction in C incorporation in LA-MOCVD GaN is especially prominent when the GaN growth rate is fast (> 10 μm/hr), which allows to develop thick GaN films with high crystalline quality and low controllable doping needed for vertical high power device applications. The results of this project lead to the demonstration of vertical GaN PN diodes with record breakdown voltage of ~ 8kV with high Baliga’s figure of merit.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2025

Compare low-gain 1D and 3D models toward a storage ring-based X-ray free-electron-laser oscillator

Fourth-generation diffraction-limited synchrotron light sources (DL-SLS) present a compelling platform for advanced light source applications due to their ultra-low emittance (around tens of picometers), sub-micrometer beam stability, and high repetition rates (greater than 1 MHz). Despite these advantages, fundamental limitations, such as long bunch durations (tens of picoseconds), large relative energy spread (~10⁻³), and low peak current (<300 A), have hindered their effectiveness in free-electron laser (FEL) applications. Using a low-gain three-dimensional (3D) model based on NSLS-II upgrade lattice parameters, we demonstrate that a 6% single-pass gain is achievable with an optimized transverse gradient undulator (TGU). Concurrently, recent advances in X-ray optics—specifically, a four-mirror bow-tie resonator utilizing diamond mirrors and beryllium compound refractive lenses (CRLs)—enable total round-trip losses below 4% and an output coupling efficiency near 1%, rendering a Storage Ring based X-ray FEL oscillator (XFELO) a realistic possibility. In the 3D framework, the TGU effectively mitigates the detrimental effects of large energy spread by spatially dispersing the beam, leading to enhanced gain relative to conventional one-dimensional (1D) models. We establish both analytical and numerical connections between the 1D and 3D descriptions, leveraging GENESIS simulations to map equivalent gain conditions. While 1D resonance is defined in the energy domain, the 3D TGU system shifts the resonance dependence to transverse gradient and dispersion parameters. Once optimized, this framework allows predictive modeling using 1D formulas, which can then be validated through full 3D simulations.

43 PARTICLE ACCELERATORS↗

DOE OSTI2022

Spatiotemporal Structure in Intense THz Pulsed Beams

Optically generated terahertz radiation, with gigavolt per meter (GV/m) electric fields accessible in tabletop experiments, provides a promising source of accelerating gradients for future particle accelerator applications. Manipulation and characterization of radiation is essential for efficiently producing high fields and effectively delivering them to an accelerating structure or interaction region. The talk will cover a method of generating and characterizing high quality and structured terahertz pulsed laser beams for compact particle acceleration.

Hine, George↗

DOE OSTI2020

Single-particle dynamics of microbunching

The mechanism of steady-state microbunching (SSMB) has been proposed [D. F. Ratner and A. W. Chao, Phys. Rev. Lett. 105, 154801 (2010)] to generate high-power coherent radiation at a high repetition rate or in continuous-wave mode using electron storage rings. In this paper, the related single-particle dynamics are theoretically and numerically studied, and important results are presented. The investigated effects are longitudinal quantum radiation excitation, nonlinear momentum compaction, and linear and nonlinear coupling of the transverse and longitudinal motion. Although this analysis is oriented toward SSMB, some of the analyzed effects are also crucial in cases such as coherent harmonic generation, bunch slicing, bunch compression, free-electron laser beam transport lines, and quasi-isochronous rings, which involve precise longitudinal phase-space manipulations.

43 PARTICLE ACCELERATORS↗

DOE OSTI2022

Angular dependence of the transverse Raman scattering in KDP and DKDP in geometries suitable for beam polarization control

The angular dependance of the transverse Raman scattering in potassium dihydrogen phosphate (KDP) and its deuterated analogue (DKDP) for the entire range of crystal configurations suitable for laser beam polarization control has been investigated via experimental and modeling tools. This work was made possible by simultaneously rotating a spherical sample and the pump polarization to effectively measure the angular dependance of the transverse Raman signal in 360°. This novel method, which is applicable for the investigation of the Raman scattering in optically anisotropic materials, demonstrates that the spontaneous Raman scattering signal exhibits strong angular dependence that is modulated by depolarization and polarization rotation effects generated as the Raman signal traverses the material due to its birefringence. The results show that the total signal generated by the pump beam is the sum of the signals generated by the two components that have polarization parallel and orthogonal to the optic axis. The peak signal intensity, which is of importance for high-power laser applications, depends on the orientation of the optic axis and can vary by a factor of about 2. The excellent agreement between experimental data and modeling results validates the associated models and enables one to consider optimal crystal cut designs for specific applications.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Proton beam quality enhancement by spectral phase control of a PW-class laser system

We report on experimental investigations of proton acceleration from solid foils irradiated with PW-class laser-pulses, where highest proton cut-off energies were achieved for temporal pulse parameters that varied significantly from those of an ideally Fourier transform limited (FTL) pulse. Controlled spectral phase modulation of the driver laser by means of an acousto-optic programmable dispersive filter enabled us to manipulate the temporal shape of the last picoseconds around the main pulse and to study the effect on proton acceleration from thin foil targets. The results show that applying positive third order dispersion values to short pulses is favourable for proton acceleration and can lead to maximum energies of 70 MeV in target normal direction at 18 J laser energy for thin plastic foils, significantly enhancing the maximum energy compared to ideally compressed FTL pulses. The paper further proves the robustness and applicability of this enhancement effect for the use of different target materials and thicknesses as well as laser energy and temporal intensity contrast settings. We demonstrate that application relevant proton beam quality was reliably achieved over many months of operation with appropriate control of spectral phase and temporal contrast conditions using a state-of-the-art high-repetition rate PW laser system.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

Noise in Intense Electron Bunches (Final Technical Report)

The goal of this project is to investigate density fluctuations in electron bunches. Noise and density fluctuations in relativistic electron bunches, accelerated in a linac, are of critical importance to various Coherent Electron Cooling (CEC) concepts as well as to free-electron lasers (FELs). For CEC, the beam noise results in additional diffusion that counteracts cooling; and if this noise is not controlled at sufficiently low level, the noise heating effects can overcome cooling. There have been several proposals in the past to suppress the noise in the beam in the frequency range of interest in order to optimize the cooling effects. In SASE FELs a microwave instability starts from the initial noise in the beam and eventually leads to the beam microbunching yielding coherent radiation, and the initial noise in the FEL bandwidth plays a useful role. In seeded FELs, in contrast, such noise interferes with the seed signal, so that reducing noise at the initial seed wavelength would lower the seed laser power requirement. Our major goals were (1) to measure the electron beam density noise level in a 0.5 – 10 um wavelength range, (2) to predict the beam noise level in order to compare with the measurements, and (3) as a stretch goal, to find mechanisms that affect the beam noise to control its level in a predictable manner.

43 PARTICLE ACCELERATORS↗

DOE OSTI2024

Accelerator Physics at NSLS-II: Research Accomplishments in 2024

NSLS-II accelerator physicists advanced the operational performance and scientific capabilities of NSLS-II, providing regular lattice characterization and correction, injec tion optimization, vertical emittance control, and beam dynamics reports with corre lation analysis. We further developed advanced lattice characterization techniques and studies on impedance, beam-induced heating, and higher-harmonic RF cavity effects to support NSLS-II and its high-brightness upgrade. The assessment of free-electron laser options for the NSLS-II upgrade has been completed. We carried out comprehensive studies focused on complex bend magnets and novel efficient injection schemes for next-generation low-emittance synchrotrons. We contributed to the Electron-Ion Collider project, including Electron Storage Ring lattice design, beam diagnostics, and injector studies. The physicists participated in international collaborations, including the development of Python-based Middle Layer software, and participated in key accel erator physics workshops and scientific meetings. The main research accomplishments achieved in 2024 are summarized in this report.

43 PARTICLE ACCELERATORS↗

DOE OSTI2023

Nonlinear models for coupling the effects of stimulated Raman scattering to inertial confinement fusion codes

Laser plasma instabilities (LPI) reduce driver-target coupling, alter implosion symmetry, and therefore can fundamentally limit fusion performance in inertial confinement fusion (ICF). Developing a predictive modeling capability for LPI effects can critically advance the success of the field. We perform vector particle-in-cell simulations of multi-speckled laser beams undergoing stimulated Raman scattering (SRS) at various densities and intensities relevant to mainly indirectly driven and a subset of parameter space for directly driven ICF systems, focusing on the regimes with intensities above the onset of electron trapping. Based on the wavenumber of the SRS daughter electron plasma wave, we identify several regions with underpinning SRS saturation physics: the electron-trapping dominated region with intermediate kλD values, the strong Landau damping region at larger kλD values, and the region where the Langmuir decay instability arises at lower kλD values. We develop a nonlinear SRS reflectivity model that features the base trapping-dominated scaling of (kλD)−4 and its modifications. Electron trapping deforms the initialized electron distribution functions, and we have developed a new δf-Gaussian-mixture algorithm for an accurate characterization of the trapped hot electron population. With this SRS hot electron description, we construct a nonlinear energy deposition model and a hot electron source model—based on a modified Manley–Rowe relation—suitable for including SRS effects as a sub-grid module in a high-fidelity ICF design code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

High-energy transient gas pinholes via saturated absorption

This Letter presents a spatial filter based on saturated absorption in gas as an alternative to the solid pinhole in a lens–pinhole–lens filtering system. We develop an analytic model that describes this process and demonstrate spatial filtering with simulations and experiments. We show that an ultraviolet laser pulse focused through ozone will have its spatial profile cleaned if its peak fluence rises above the ozone saturation fluence. Specifically, we demonstrate that a 5 ns 266 nm beam with 4.2 mJ of the initial energy can be effectively cleaned by focusing through a 1.4% ozone–oxygen mixture, with about 76% of the main beam energy transmitted and 89% of the sidelobe energy absorbed. In conclusion, this process can be adapted to other gases and laser wavelengths, providing alignment-insensitive and damage-resistant pinholes for high-repetition-rate high-energy lasers.

Ou, K. [Stanford Univ., CA (United States)] (ORCID↗

DOE OSTI2022

Raman gain control in optical fibers with orbital-angular-momentum-induced chirality of light

Stimulated Raman scattering is a particularly robust nonlinearity, occurring in virtually every material because its spectral linewidth and associated frequency shift do not typically depend on phases or directions (i.e. wavevectors) of the interacting light beams. In amorphous materials such as glass fibers, Raman bandwidths are large, enabling its use as a broadband gain element. This ubiquity makes it a versatile means for achieving optical amplification or realizing lasers over a large range of pulsewidths at user-defined colors. However, this ease of deploying the effect also presents itself as a stubborn source of noise in fiber-based quantum sources or parasitic emission in fiber lasers. Here, we show that orbital angular momentum carrying light beams experiencing spin-orbit interactions yield novel phase-matching criteria for Raman scattering. This enables tailoring its spectral shape (by over half the Raman shift in a given material) as well as strength (by ∼ 100×) simply by controlling light’s topological charge – a capability of utility across the multitude of applications where modulating Raman scattering is desired.

Liu, Xiao (ORCID:000000032239762X)↗

DOE OSTI2019

A computational model for nanosecond pulse laser-plasma interactions

A multi-physics numerical model for laser-induced optical breakdown and laser-plasma interaction in a non-equilibrium gas is presented, accounting for: production of priming electrons via multi-photon ionization, energy absorption, cascade ionization, induced hydrodynamic response, and shock formation and propagation. The gas is governed by the Navier-Stokes equations, with non-equilibrium effects taken into account by means of a two-temperature model. The space-time dependence of the laser beam is modeled with a flux-tube formulation for the Radiative Transfer Equation. The flow governing equations are discretized in space using a second-order finite volume method. The semi-discrete equations are marched in time using an implicit-explicit (IMEX) dual time-stepping strategy, where diffusion and chemistry are solved implicitly, whereas convection is explicit. Application to a 20 ns long 50 mJ pulse laser-induced breakdown in quiescent O 2 shows the advantages of this temporal discretization during and just after the laser pulse, while a less-expensive symmetric Strang splitting (with implicit chemistry) is sufficient for the post-breakdown gas dynamics after ≃ 0.1 μs. The integrated model is shown to reproduce key features of corresponding experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Effect of CO{sub 2}-laser power density on the absorption coefficient of polycrystalline CVD diamonds

The effect of 1-s irradiation of an uncooled polycrystalline CVD diamond plate by a focused cw CO{sub 2} laser beam with a power density of 300 – 800 kW cm{sup −2} is investigated. The absorption coefficient of the sample at a power density of 800 kW cm{sup −2} is found to be 0.035 cm{sup −1} larger as compared with that at 300 kW cm{sup −2}, which is related to the temperature dependence of its phonon-induced absorption with a change in temperature from 44 to 100 °C. It is shown that polycrystalline diamond, in contrast to other optical materials, does not exhibit nonlinear (avalanche-like) rise in absorption at high CO{sub 2}-laser power densities, at least up to 800 kW cm{sup −2}. (paper)

36 MATERIALS SCIENCE↗

DOE OSTI2020

Pre-Ionization Controlled Laser Plasma Formation for Ignition Applications (Final Scientific/Technical Report)

This report consists of three grand funded papers. Abstracts for each follow. 1) In this work, we present experimental and modeling studies of air pre-ionization using ultraviolet (UV) laser pulses and its effect on laser breakdown of an overlapped near-infrared (NIR) pulse. Experimental studies are conducted with a 266 nm beam (fourth harmonic of Nd:YAG) for UV pre-ionization and an overlapped 1064 nm NIR beam (fundamental of Nd:YAG), both having pulse duration of 10 ns. Results show that the UV beam produces a pre-ionized volume which assists in breakdown of the NIR beam, leading to reduction in NIR breakdown threshold by factor of >2. Numerical modeling is performed to examine the ionization and breakdown of both beams. The modeled breakdown threshold of the NIR, including assist by pre-ionization, is in reasonable agreement with the experimental results. 2) The present contribution compares the energy absorption, optical emission, temperature, and fluid dynamics of ultraviolet (UV) λ = 266 nm and near infrared (NIR) λ = 1064 nm nanosecond laser induced plasmas in ambient air. For UV pulses at the conditions studied, energy absorption by the plasmas increases relatively gradually with laser pulse energy starting at delivered energy of E~8 mJ. Corresponding measurements of plasma luminosity show that the absorption of UV radiation does not necessarily result in visible plasma emission. For the NIR induced plasmas, the energy absorption profile is far more abrupt and begins at ~55 mJ. In contrast with UV, the absorption of NIR radiation is always accompanied by intense optical emission. The temperatures of both types of plasma have been measured with Rayleigh scattering thermometry (at times after the Thomson signal sufficiently diminishes). The UV plasmas can attain a wider range of temperatures, including lower temperatures, depending on the pulse energy (e.g., T ~400–2000K for E ~7–35 mJ at Δt = 10 μs after the pulse) while the NIR plasmas show only hotter temperatures (e.g., T ~ 12 000 K for E = 75 mJ at Δt = 10 μs after the pulse) as is consistent with the literature. Differences in the fluid dynamics for UV versus NIR pulses are shown with Schlieren imaging. In this work, the contrast in the UV and NIR plasma threshold behavior is attributed to differing roles of avalanche ionization and multiphoton ionization as is also illustrated by a simple numerical model. 3) The present contribution examines the impact of plasma dynamics and plasma-driven fluid dynamics on the flame growth of laser ignited mixtures and shows that a new dual-pulse scheme can be used to control the kernel formation process in ways that extend the lean ignition limit. We perform a comparative study between (conventional) single-pulse laser ignition (λ = 1064 nm) and a novel dual-pulse method based on combining an ultraviolet (UV) pre-ionization pulse (λ = 266 nm) with an overlapped near-infrared (NIR) energy addition pulse (λ = 1064 nm). We employ OH* chemiluminescence to visualize the evolution of the early flame kernel. For single-pulse laser ignition at lean conditions, the flame kernel separates through third lobe detachment, corresponding to high strain rates that extinguish the flame. In this work, we investigate the capabilities of the dual-pulse to control the plasma-driven fluid dynamics by adjusting the axial offset of the two focal points. In particular, we find there exists a beam waist offset whereby the resulting vorticity suppresses formation of the third lobe, consequently reducing flame stretch. With this approach, we demonstrate that the dual-pulse method enables reduced flame speeds (at early times), an extended lean limit, increased combustion efficiency, and decreased laser energy requirements.

Mechanical engineering↗

DOE OSTI2020

Effect of cross-beam energy transfer on target-offset asymmetry in direct-drive inertial confinement fusion implosions

The unintentional mispositioning of inertial confinement fusion (ICF) capsules from the center of laser beam convergence has long been shown in simulations to generate large ℓ = 1 asymmetry and significantly degrade implosion symmetry and fusion yields. Experimental yields on the OMEGA Laser System, however, have shown much less sensitivity to this initial target offset. This paper presents simulations of offset ICF implosions improved by including a physics model of cross-beam energy transfer (CBET), a mechanism of laser energy scattering from one beam to another. Room-temperature OMEGA implosion experiments with prescribed target offsets are simulated with and without CBET, illustrating that CBET mitigates the ℓ = 1 implosion asymmetry from target offset. Here, comparison of simulations to multiple complementary experimental observables indicates the addition of CBET physics in offset simulations is necessary to match experimental results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗