Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lattice–Boltzmann”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Comparative Study of Active Flow Control Strategies for Lift Enhancement of a Simplified High-Lift Configuration

Numerical simulations have been performed for a simplified high-lift (SHL) version of the Common Research Model (CRM) configuration, where the Fowler flaps of the conventional high-lift (CRM-HL) configuration are replaced by a set of simple hinged flaps. These hinged flaps are equipped with integrated modular active flow control (AFC) cartridges on the suction surface, and the resulting geometry is known as the CRM-SHL-AFC configuration. The main objective is to make use of AFC devices on the CRM-SHL-AFC configuration to recover the aerodynamic performance (lift) of the CRM-HL configuration. In the current paper, a Lattice Boltzmann method-based computational fluid dynamics (CFD) code, known as PowerFLOWQ® is used to simulate the entire flow field associated with the CRM-SHL-AFC configuration equipped with several different types of AFC devices. The transonic version of the PowerFLOWQ® code that has been validated for high speed flows is used to accurately simulate the flow field generated by the high-momentum actuators required to mitigate reversed flow regions on the suction surfaces of the main wing and the flap. The numerical solutions predict the expected trends in aerodynamic forces as the actuation levels are increased. More efficient AFC systems and actuator arrangements emerged based on the parametric studies performed prior to a Fall 2018 wind tunnel test. Preliminary comparisons of the numerical solutions for lift and surface pressures are presented here with the experimental data, demonstrating the usefulness of CFD for predicting the flow field and lift characteristics of AFC-enabled high-lift configurations.

Vatsa, Veer N.↗
NASA NTRS2019

Measured and Simulated Acoustic Signature of a Full-Scale Aircraft with Airframe Noise Reduction Technology Installed

Microphone phased-array and pole-mounted microphone data gathered during the NASA Acoustics Research Measurements flight tests were used to benchmark results from companion full-scale aeroacoustics simulations. Conducted with the lattice Boltzmann solver PowerFLOW®, the simulations predicted the acoustic behavior of various tested aircraft configurations. Emphasis was placed on those flown during the third flight test - a Fowler flap-equipped Gulfstream G-III with and without noise abatement technology on the main landing gear. Direct comparisons between experimental and synthetic microphone phasedarray data were achieved by applying the same processing and deconvolution technique to both sets of data. To extend the validation of the computations to the metric used for noise certification, the Effective Perceived Noise Level, a high-fidelity digital model of the nose landing gear, which was excluded from earlier computations, was developed and integrated into the G-III aircraft geometry. The acoustic study presented here demonstrates that the simulated beamform maps and corresponding integrated farfield spectra accurately predict the locations and strengths of the prominent airframe noise sources present on the G-III aircraft.

Khorrami, Mehdi R.↗
NASA NTRSDate not supplied

CFD and Experimental Data Comparisons for Conventional and AFC-Enabled CRM High-Lift Configurations

Numerical simulations have been performed for a simplified high-lift (SHL) version of the Common Research Model (CRM) configuration, where the Fowler flaps of a representative conventional high-lift (CRM-HL) configuration are replaced by a set of simple hinged flaps. These hinged flaps are equipped with integrated modular active flow control (AFC) cartridges on the suction surface of the flap shoulder, and the resulting geometry is known as the CRM-SHL-AFC configuration. The main objective is to make use of AFC devices on the CRM-SHL-Configuration to produce the aerodynamic performance (lift) comparable to that of the CRM-HL configuration over a large angle of attack range encompassing maximum lift conditions. For comparison purposes, computations are also per-formed for the CRM-HL configuration. In the current paper, PowerFLOWR©, a CFD code based on the Lattice Boltzmann method (LBM), is used to simulate the entire flow field associated with the CRM-SHL-AFC configuration equipped with a combination of two different types of AFC actuators. The transonic version of the PowerFLOWR© code that has been validated for high-speed flows is used to simulate the flow field generated by the high-momentum actuators required to mitigate reversed flow regions on the suction surfaces of the main wing and the flap. This study is focused on the AFC systems and actuator arrangements that had emerged based on the parametric studies conducted previously at the nominal landing condition. Comparisons of the numerical solutions for lift and surface pressures are presented here with the experimental data, demonstrating the usefulness of CFD for predicting the flow field and lift characteristics of AFC-enabled high-lift configurations over a broad angle of attack range. The numerical solutions predict the expected trends in aerodynamic forces with angle of attack variation.

Veer N Vatsa↗
NASA NTRSDate not supplied

Physics Informed Broadband Noise Source Identification and Prediction of an Ideally Twisted Rotor

This work aims at a physics based approach for the prediction and isolation of broadband noise emanating from different regions of an ideally twisted rotor. A preliminary prediction was conducted using a lattice-Boltzmann method–very-large-eddy simulation (LBM-VLES) implemented within the software suite, PowerFLOW. Regions of particular interest to broadband noise were investigated by calculating one-third octave sound pressure levels of the unsteady pressure fluctuations acting on the rotor. These regions were then isolated and treated as individual Ffowcs Williams-Hawkings (FW-H) surfaces for three run conditions at a much finer spatial resolution to delineate the broadband noise from these separate regions from the total acoustic spectra. These predictions were then compared to experimentally acquired data as well as to semi-empirical prediction methods to highlight the acoustic contributions of various broadband noise generation mechanisms as well as to exemplify and explain shortcomings in the semi-empirical methodology.

Christopher S Thurman↗
NASA NTRSDate not supplied

Computational Prediction of Broadband Noise from a Representative Unmanned Aerial System Rotor

This work details the application of a lattice-Boltzmann method–very-large-eddy simulation (LBM-VLES) employed by the software suite, PowerFLOW. This LBM-VLES simulation predicted the aeroacoustic noise emanating from a representative, small unmanned aircraft system rotor, namely, the DJI-9450 in a hover condition. Predicted total aerodynamic loading as well as 2D aerodynamic loading along discrete spanwise sections of a rotor blade were compared to lower fidelity predictions and experimental results acquired in the Structural Acoustic Loads and Transmission anechoic chamber facility at the NASA Langley Research Center. The total acoustic spectra were decomposed into tonal and broadband components, which showed that broadband noise was a dominant contributor above 1 kHz for this rotor. These data were then compared to experimentally acquired data, showing good agreement up to approximately 11 kHz. Above 11 kHz, however, a grid sensitivity study showed dependency of the highest resolvable frequency on the spatial resolution of the computational domain, explaining the roll off in predicted data. Individual broadband noise sources were further investigated by calculating one-third octave sound pressure levels of the unsteady pressure fluctuations acting on the rotor, providing evidence that blade self-noise was the prominent noise source. Using these results, blade wake interaction noise was seen to be negligible for this particular rotor, which was further validated by calculating blade vortex miss distances and comparing to theory.

Christopher S. Thurman↗
NASA NTRSDate not supplied

Physics-Informed Broadband Noise Source Identification and Prediction of an Ideally Twisted Rotor

This work aims to provide a physics-based approach for the prediction and isolation of broadband noise emanating from different regions of an ideally twisted rotor. A preliminary prediction was conducted using a lattice-Boltzmann method–very-large-eddy simulation (LBM-VLES) implemented within the software suite, PowerFLOW. Regions of particular interest to broadband noise were investigated by calculating one-third octave sound pressure levels of the unsteady pressure fluctuations acting on the rotor. These regions were then treated as individual Ffowcs Williams and Hawkings (FW-H) surfaces and simulated for three run conditions at a finer spatial resolution to identify the broadband noise from these separate regions and isolate it from the total acoustic spectra. These predictions were then compared to experimentally acquired data and to semiempirical prediction methods to highlight the acoustic contributions of various broadband noise generation mechanisms as well as to exemplify and explain shortcomings in the semiempirical methodology.

Christopher S Thurman↗
NASA NTRSDate not supplied

Aeroacoustic Study of a Subscale Large Civil Transport (STAR) Model – Part 2: Validation of Simulated Results

Aeroacoustic measurements of the 26%-scale, semispan Boeing 777-200 Subsonic Transport Aeroacoustic Research (STAR) model tested in the NASA Ames Research Center 40- by 80-foot wind tunnel were used to ascertain the efficacy of high-fidelity simulations to accurately predict noise from the landing gear of large commercial transports. The simulations, conducted with the lattice Boltzmann solver PowerFLOW®, used a digital replica of the STAR model with or without main landing gear deployed and slats and flaps set to their highest deflection angles to represent aircraft during landing. The computations were performed at a Mach number of 0.21, Reynolds number of 8.2 million based on the model mean aerodynamic chord, and other conditions prevalent during the STAR model test. Measured and computed surface pressures were in very good agreement at most port locations on the model, as were global force coefficients, indicating that the simulations captured the impact of main gear deployment on inboard flap loading. Noise sources produced by the main landing gear and high-lift devices were determined via source localization maps generated with CLEAN from synthetic and experimental data. In general, very good agreement between predicted and measured acoustic source location and relative strength was observed in the maps. Comparisons of far-field noise spectra obtained from the CLEAN deconvolution maps showed remarkable agreement between synthetic and experimental broadband noise at low and medium frequencies. Main landing gear sources for model-scale frequencies above 7,000 Hz could not be resolved with the spatial resolution used during the simulations.

airframe noise↗
NASA NTRSDate not supplied

Airframe Noise Simulations of a Full-Scale Large Civil Transport in Landing Configuration

This paper summarizes the results obtained from an extensive computational campaign to accurately predict full-scale landing gear noise for large civil transports. A highly accurate digital model of a full-scale Boeing 777-300ER aircraft with as-flown nose and main landing gear components was developed for use in the simulations. Two aircraft configurations were selected: nose and main landing gear deployed with wing high-lift devices retracted, and nose and main landing gear deployed with wing high-lift devices deflected. The two configurations were simulated without and with toboggan fairings installed on the main gear to represent the principal configurations evaluated during the 2005 QTD2 flight test. All simulations were performed with the lattice Boltzmann solver PowerFLOW® to resolve and capture the highly complex, unsteady flow field in the immediate vicinity of the aircraft. The far-field noise sig-nature of the aircraft was computed via a Ffowcs-Williams and Hawkings integral approach, with flow quantities on a permeable surface enclosing the source regions used as input. Synthetic pressure records at ground array microphone locations used during the QDT2 test were employed to generate narrowband acoustic maps and integrated far-field noise spectra. With high-lift devices retracted, the predicted spectra showed that landing gear noise is equivalent to total airframe noise, with no other airframe sources appearing within 10 dB of gear peak levels. Application of a toboggan fairing to the main gear produced modest noise reductions of 1-2 dB across the resolved frequency range. With high-lift devices deflected, undercarriage noise was within 3-4 dB of the total airframe noise, thus comprising nearly half of the total airframe noise. For this configuration, the toboggan fairing did not produce a reduction in noise, corroborating trends previously observed in QTD2 flight test data.

airframe noise↗
NASA NTRSDate not supplied

Aeroacoustic Computations of a Generic Low Boom Concept in Landing Configuration: Part 2 - Airframe Noise Simulations

Aeroacoustic simulations of a sub-scale, generic, low-boom supersonic aircraft model at low speeds were carried out using the Lattice-Boltzmann Very Large Eddy Simulation software PowerFLOW® and a Ffowcs Williams and Hawkings approach. The objective was to characterize the airframe noise signature of the configuration and determine the similarities and differences to conventional subsonic aircraft. We quantified the noise produced by the flap and landing gear by simulating the aircraft with and without deployment of these components. Mach number scaling of the far-field noise levels was examined by performing simulations at different flow speeds. We demonstrate that a solid surface formulation does not capture the aircraft acoustic field properly, while a carefully constructed permeable surface formulation yields far-field spectra that compare very favorably to results from direct probing of the simulated flow field.

low boom↗
NASA NTRSDate not supplied

Aeroacoustic Computations of a Generic Low Boom Concept in Landing Configuration: Part 1 - Aerodynamic Simulations

Computational results are presented for a 15%-scale, full-span, generic low-boom concept aircraft model simulated as installed in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel and in free-air conditions. The simulations were conducted with the lattice Boltzmann solver PowerFLOW® to capture the time-accurate characteristics of the flow. The aerodynamic behavior of the aircraft was investigated with various combinations of flap and landing gear deployments. To replicate the flow speed used during tests of the model, a Mach number of approximately 0.20 was chosen while varying the angle of attack through a limited range. Analyses were performed on local flow quantities, global forces, as well as flow distributions between configurations. Aerodynamic quantities were shown to be sensitive to mesh resolution levels, especially with flap and landing gear systems retracted. When comparing wind tunnel to free-air simulations, the aerodynamic quantities sampled were found to be in good agreement, suggesting that tunnel blockage and model support effects did not adversely impact the aerodynamic behavior of the model during the wind tunnel test. The results of this study improve our understanding of the highly complex, vortical flow generated by configurations with swept, low aspect-ratio wings at speeds encountered during landing operations.

low boom↗
NASA NTRSDate not supplied

Comparison of Boeing 777 Landing Gear Noise Simulations with Flight Test Data

Acoustic phased microphone array measurements of aircraft flyover noise acquired during the 2005 Quiet Technology Demonstrator II test were used to assess the accuracy of high-fidelity, full-scale simulations of landing gear noise produced by a large civilian aircraft. The simulations, conducted with the lattice Boltzmann solver PowerFLOW®, used a highly accurate digital model of a Boeing 777-300ER aircraft with the nose and main landing gear components replicating the full-scale geometries. The simulations were performed for aircraft parameters that matched those recorded during the flyover test conditions. For benchmarking purposes, several aircraft configurations were simulated: a) nose landing gear deployed with main landing gear and wing high-lift devices stowed, b) nose and main landing gear deployed with wing high-lift devices stowed and c) nose and main landing gear with wing high-lift devices deployed. To facilitate direct comparison with measured data, the simulated data sets were used to generate synthetic pressure records at the same array microphone locations as those used during the flight test. Broadly self-consistent beamforming techniques and procedures were used to process the synthetic pressure records and the measured data. Integration of select regions of the beamform maps containing the nose or main landing gear yielded good agreement between predicted and measured integrated far-field spectra for forward directivity angles where airframe noise is more prominent.

airframe noise↗
NASA NTRSDate not supplied

Summary of the 5th Propulsion Aerodynamics Workshop Nozzle Test Case: Heated Nozzle Exhaust Passing Over A Film-Cooled Plate

This paper summarizes findings from the fifth AIAA Propulsion Aerodynamics Workshop nozzle test case. The experimental configuration examined by workshop participants was a subsonic nozzle with a square exit blowing a heated exhaust over a film-cooled plate. Computational fluid dynamics solutions were obtained and compared to experimental measurements of flow velocities and temperatures, as well as plate surface temperatures. The heated nozzle operated with a Mach 0.3 exit flow at a static temperature ratio of 2.7. Cooling air blowing ratios of 0, 1, and 2 were considered. Computational meshes for the flow domain were provided for participants. Workshop participants from eight separate organizations represented government, industry, and academia. A variety of flow solutions were obtained: Most of the flow solutions employed a Reynolds-averaged Navier-Stokes (RANS) approach, but scale-resolving simulations were used in some cases, including wall-modeled large-eddy simulation (LES), and a few hybrid RANS-LES approaches. One Lattice-Boltzmann solver was employed. For heat transfer to the test article, many participants used a conjugate heat transfer approach. Effects of mesh sensitivity, flow solution approach, and wall heat transfer approach are considered. In general, a fully three-dimensional conjugate heat transfer approach enabled better prediction of surface temperatures than simpler wall temperature boundary treatments. Also, the scale resolving approaches provided better prediction of static temperatures in the flow immediately above the plate consisting of the hot jet exhaust boundary layer interacting with the cooling film. Comparisons of plate surface friction drag and heat transfer obtained from the computations are also presented.

nozzle↗
NASA NTRSDate not supplied

Summary of the 5th Propulsion Aerodynamics Workshop Nozzle Test Case: Heated Nozzle Exhaust Passing Over A Film-Cooled Plate

This paper summarizes findings from the fifth AIAA Propulsion Aerodynamics Workshop nozzle test case. The experimental configuration examined by workshop participants was a subsonic nozzle with a square exit blowing a heated exhaust over a film-cooled plate. Computational fluid dynamics solutions were obtained and compared to experimental measurements of flow velocities and temperatures, as well as plate surface temperatures. The heated nozzle operated with a Mach 0.3 exit flow at a static temperature ratio of 2.7. Cooling air blowing ratios of 0, 1, and 2 were considered. Computational meshes for the flow domain were provided for participants. Workshop participants from eight separate organizations represented government, industry, and academia. A variety of flow solutions were obtained: Most of the flow solutions employed a Reynolds-averaged Navier-Stokes (RANS) approach, but scale-resolving simulations were used in some cases, including wall-modeled large-eddy simulation (LES), and a few hybrid RANS-LES approaches. One Lattice-Boltzmann solver was employed. For heat transfer to the test article, many participants used a conjugate heat transfer approach. Effects of mesh sensitivity, flow solution approach, and wall heat transfer approach are considered. In general, a fully three-dimensional conjugate heat transfer approach enabled better prediction of surface temperatures than simpler wall temperature boundary treatments. Also, the scale resolving approaches provided better prediction of static temperatures in the flow immediately above the plate consisting of the hot jet exhaust boundary layer interacting with the cooling film. Comparisons of plate surface friction drag and heat transfer obtained from the computations are also presented.

nozzle↗
NASA NTRSDate not supplied

Prediction of Broadband Blade-Wake Back-Scatter Noise from a Hovering Ideally Twisted Rotor using OVERFLOW2-ANOPP2

This work illustrates the use of a hybrid RANS/LES framework for the prediction of broadband noise via integral formulations from an ideally twisted hovering rotor. Four simulations were conducted, which investigated the effect of different turbulence modeling and spatiotemporal resolutions. The aerodynamic performance and aeroacoustics predicted by these four computational cases were compared against data acquired in the Small Hover Anechoic Chamber at the NASA Langley Research Center and against previous simulations conducted using the lattice-Boltzmann solver, PowerFLOW. The simulation case with the finest spatial resolution had the most favorable aerodynamic performance and broadband noise comparison with measured data; however, the simulation case utilizing the SST-DDES turbulence model predicted the most accurate tonal noise signature. Aerodynamic flowfield visualizations identified near-wake trailing edge vortex shedding, perpendicular blade-vortex interactions, and tip vortex formation, which are known to cause broadband noise. The fluid dynamics associated with a new broadband noise source, blade-wake back-scatter, were also identified. Lastly, a broadband noise source visualization technique was utilized to confirm the presence of blade-wake back-scatter as a dominant broadband noise source.

blade-wake back-scatter↗
DOE OSTI2024

PYSIMFRAC: A Python library for synthetic fracture generation and analysis

In this paper, we introduce PYSIMFRAC, an open-source python library for generating 3-D synthetic fracture realizations, integrating with fluid simulators, and performing analysis. PYSIMFRAC allows the user to specify one of three fracture generation techniques (Box, Gaussian, or Spectral) and perform statistical analysis including the autocorrelation, moments, and probability density functions of the fracture surfaces and aperture. This analysis and accessibility of a python library allows the user to create realistic fracture realizations and vary properties of interest. In addition, PYSIMFRAC includes integration examples to two different pore-scale simulators and the discrete fracture network simulator, dfnWorks. The capabilities developed in this work provides opportunity for quick and smooth adoption and implementation by the wider scientific community for accurate characterization of fluid transport in geologic media. We present PYSIMFRAC along with integration examples and discuss the ability to extend PYSIMFRAC from a single complex fracture to complex fracture networks.

58 GEOSCIENCES↗
DOE OSTI2025

Mechanistic understanding of carbon mineralization in fracture systems using microfluidics

Carbon mineralization in mafic and ultramafic rocks presents an opportunity for permanent carbon storage in the Earth's subsurface. However, due to their lower permeability, pre-existing fracture networks are key for mineralization to occur. Therefore, to fully develop this technology, a mechanistic understanding of the mineralization behavior in fractures with the consideration of hydrodynamic components is required. We use high-pressure microfluidics to investigate key mechanisms influencing dissolution–precipitation in a fracture network. The experiments were conducted in micromodels made of natural rocks with a comb-shaped flow channel to mimic a fracture network. This enabled studying the effect of injection rate on coupled dissolution–precipitation in advection and diffusion-dominated flow paths. We used gypsum carbonation as an analog reaction to allow for realistic experimental time frames due to its rapid reaction kinetics. The experimental work is coupled with high-fidelity numerical simulations to enhance our understanding of the parameters affecting the mineralization reaction. Our results demonstrate the importance of flow rate on the rate and nature of the gypsum carbonation reaction revealing that higher flow rates enable deeper penetration of the mineral precipitation front into the dead-end channels. This is an important finding since for sustained mineralization in a fracture network, precipitation in dead-ends while still allowing for flowing fractures is critical. Detailed characterization of the precipitates showed that lower flow rates led to porous and loose precipitates in the form of aragonite while higher flow rates mimicked supersaturation behavior leading to the formation of calcite. The reactive transport simulations further demonstrated the significance of flow velocity in advection-dominated channels to influence the efficiency of carbon mineralization in diffusion-dominated channels, potentially clogging of dead-end channels. These findings highlight the need for coupling chemical, mechanical, and hydrodynamic processes to evaluate the nature and extent of carbon mineralization in fractured media critical for permanent storage in mafic and ultramafic formations. This research further highlights the need for more investigation in potential subsurface fracture generation techniques to aid carbon mineralization.

25 ENERGY STORAGE↗
DOE OSTI2024

Learning a general model of single phase flow in complex 3D porous media

Modeling effective transport properties of 3D porous media, such as permeability, at multiple scales is challenging as a result of the combined complexity of the pore structures and fluid physics—in particular, confinement effects which vary across the nanoscale to the microscale. While numerical simulation is possible, the computational cost is prohibitive for realistic domains, which are large and complex. Although machine learning (ML) models have been proposed to circumvent simulation, none so far has simultaneously accounted for heterogeneous 3D structures, fluid confinement effects, and multiple simulation resolutions. By utilizing numerous computer science techniques to improve the scalability of training, we have for the first time developed a general flow model that accounts for the pore-structure and corresponding physical phenomena at scales from Angstrom to the micrometer. Using synthetic computational domains for training, our ML model exhibits strong performance (R 2 = 0.9) when tested on extremely diverse real domains at multiple scales.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Fully quantum algorithm for mesoscale fluid simulations with application to partial differential equations

Fluid flow simulations marshal our most powerful computational resources. In many cases, even this is not enough. Quantum computers provide an opportunity to speed up traditional algorithms for flow simulations. We show that lattice-based mesoscale numerical methods can be executed as efficient quantum algorithms due to their statistical features. This approach revises a quantum algorithm for lattice gas automata to reduce classical computations and state preparation at every time step. For this, the algorithm approximates the qubit relative phases and subtracts them at the end of each time step. Phases are evaluated using the iterative phase estimation algorithm and subtracted using single-qubit rotation phase gates. Further, this method optimizes the quantum resource required and makes it more appropriate for near-term quantum hardware. We also demonstrate how the checkerboard deficiency that the D1Q2 scheme presents can be resolved using the D1Q3 scheme. The algorithm is validated by simulating two canonical partial differential equations: the diffusion and Burgers' equations on different quantum simulators. We find good agreement between quantum simulations and classical solutions for the presented algorithm.

97 MATHEMATICS AND COMPUTING↗