SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Materials applied to molds as powders, dispersions, or solutions not only enable release of molded parts from molds, but also enhance properties of surfaces of parts. Applied to casting of lead grids or other molding operations in which powdered materials adhering to molded parts improve properties of surfaces.
Balanced-pressure molds used to make parts in complex shapes from fiber-reinforced metal-matrix composite materials. In single step, molding process makes parts in nearly final shapes; only minor finishing needed. Because molding pressure same on inside and outside, mold does not have to be especially strong and can be made of cheap, nonstructural material like glass or graphite. Fibers do not have to be cut to conform to molds. Method produces parts with high content of continuous fibers. Parts stiff but light in weight, and coefficients of thermal expansion adjusted. Parts resistant to mechanical and thermal fatigue superior to similar parts made by prior fabrication methods.
Rotational molding is a unique process for producing hollow plastic parts. Rotational molding offers advantages of low cost tooling and can produce very large parts with complicated shapes. Products made by rotational molding include water tanks with capacities up to 20,000 gallons, truck bed liners, playground equipment, air ducts, Nylon fuel tanks, pipes, toys, stretchers, kayaks, pallets, and many others. Thermotropic liquid crystalline polymers are an important class of engineering resins employed in a wide variety of applications. Thermotropic liquid crystalline polymers resins are composed of semi-rigid, nearly linear polymeric chains resulting in an ordered mesomorphic phase between the crystalline solid and the isotropic liquid. Ordering of the rigid rod-like polymers in the melt phase yields microfibrous, self-reinforcing polymer structures with outstanding mechanical and thermal properties. Rotational molding of liquid crystalline polymer resins results in high strength and high temperature hollow structures useful in a variety of applications. Various fillers and reinforcements can potentially be added to improve properties of the hollow structures. This paper focuses on the process and properties of rotationally molded liquid crystalline polymers.
Rotational molding is a unique process for producing hollow plastic parts. Rotational molding offers low cost tooling and can produce very large parts with complicated shapes. Products made by rotational molding include water tanks with capacities up to 20,000 gallons, truck bed liners, playground equipment, air ducts, Nylon fuel tanks, pipes, toys, stretchers, kayaks, pallets, and many others. Thermotropic liquid crystalline polymers are an important class of engineering resins employed in a wide variety of applications. Thermotropic liquid crystalline polymers resins are composed of semirigid, nearly linear polymeric chains resulting in an ordered mesomorphic phase between the crystalline solid and the isotropic liquid. Ordering of the rigid rod-like polymers in the melt phase yields microfibrous, self-reinforcing polymer structures with outstanding mechanical and thermal properties. Rotational molding of liquid crystalline polymer resins results in high strength and high temperature hollow structures useful in a variety of applications. Various fillers and reinforcements can potentially be added to improve properties of the hollow structures. This paper focuses on the process and properties of rotationally molded liquid crystalline polymers. This paper will also highlight the interactions between academia and small businesses in developing new products and processes.
Oak Ridge National Laboratory s Big Area Additive Manufacturing (BAAM) technology permits the rapid production of thermoplastic composite molds using a carbon fiber filled Acrylonitrile-Butadiene-Styrene (ABS) thermoplastic. Demonstration tools (i.e. 0.965 m X 0.559 m X 0.152 m) for composite part fabrication have been printed, coated, and finished with a traditional tooling gel. We present validation results demonstrating the stability of thermoplastic printed molds for room temperature Vacuum Assisted Resin Transfer Molding (VARTM) processes. Arkema s Elium thermoplastic resin was investigated with a variety of reinforcement materials. Experimental results include dimensional characterization of the tool surface using laser scanning technique following demolding of 10 parts. Thermoplastic composite molds offer rapid production compared to traditionally built thermoset molds in that near-net deposition allows direct digital production of the net geometry at production rate of 45 kg/hr.
A method loading powder into a mold can include immersing the mold comprising one or more microchannels into a suspension comprising the powder and a surfactant suspended in a dispersant, wherein the powder comprises particles having an average particle size of less than 100 μm, wherein the mold is substantially entirely covered by the suspension; heating the suspension having the mold immersed therein under a temperature condition suitable to lower the stability of the particles of the powder in the suspension such that the particles settle out of solution and into the one or more microchannels; and applying an ultrasonic wave to the heated suspension to further settle the particles of the powder into the one or more microchannels thereby filling the one or more microchannels of the mold with the powder.
Hybrid tooling is an emerging concept introduced in the aerospace industries to reduce weight and cost of traditional tools. A hybrid tool features a skin, which provides desired surface quality, durability, and a low-density substrate to reduce the weight of the mold. The big area additive manufacturing (BAAM) technology permits rapid production of thermoplastic polymer intensive large-scale structures. The present study features a carbon fiber reinforced polyphenylene sulfide (CF-PPS) substrate fabricated using Oak Ridge National Laboratory's BAAM system. Carbon fiber-bismaleimide (CF-BMI) prepreg skin was then bonded to the BAAM tool through high-pressure autoclave molding. Process optimization was conducted to improve the bonding between CF-PPS and CF-BMI (transverse tensile strength increased from 0.54 to 4.8 MPa). Durability of the mold was demonstrated from fabricating seven (7) carbon fiber-Huntsman epoxy hand lay-up parts utilizing the mold.
In this article, a new type of electromagnetic braking (EMBr), named vertical EMBr (V-EMBr) was introduced in the continuous casting process. In order to investigate its capability and applicability, the impacts of horizontal and vertical EMBrs on the flow pattern in a continuous casting mold were simulated by means of an implemented Reynolds-averaged Navier–Stokes (RANS) SST k–ω turbulence model. The characteristics of electromagnetic field and flow field inside a 1450 mm × 230 mm mold with Ruler-EMBr and V-EMBr have been compared. The numerical simulation results indicate that the static magnetic field generated by Ruler-EMBr can cover the main part of the discharging jet flow, which has a better control of the flow pattern in lower part of the mold. The static magnetic field generated by V-EMBr can cover both the vicinity of the mold narrow faces and the impingement region of the jet flow, which can effectively control the liquid steel flow in the upper recirculation zone. The parametric study also shows that the large vortices beneath the jet flow can be almost completely eliminated at an optimized magnetic flux density with Ruler-EMBr. In addition, the surface velocity and steel/slag interface fluctuation can be suppressed with the application of V-EMBr to acceptable values even with a wide variation of SEN port angles. It is estimated that to reach the same level of braking effect on the upper recirculation flow, a magnetic flux density of 0.1 T is sufficient for V-EMBr, while 0.2 T is needed for Ruler-EMBr. Based on the results, a second-generation V-EMBr has been developed, which combines both of the merits of Ruler-EMBr and V-EMBr.
The drawback of steel fluid flow phenomena for a continuous casting mold under an electromagnetic stirrer with a traveling magnetic field is the resulting severe meniscus fluctuations due to the high-velocity and excessive downward flow in the casting direction. This can result in slab surface defects due to mold flux or inclusion entrainment. To inhibit these defects in the as-cast steel products, the implementation of braking forces using static magnetic fields in combination with a traveling magnetic field was studied in the current study. The numerical results of the fluid flow in the mold under a combined traveling and static magnetic field operation show not only 50 pct lower downward flow speed, but also more enhanced rotational flow to improve washing effects. The numerical results were validated in commercial-scale operations. The results suggest the optimized range of the ratio between the traveling and static magnetic flux densities is 65 to 75 pct to ensure steel quality improvements; this range maintains a balance between the fluid forces from the jet flow and the magnetic forces in the mold.
A thermoviewer-enhanced infrared emitter technique was developed in this article to study the heat-transfer behavior of mold flux in the continuous casting mold. Then, a radiation–conduction heat-transfer model was built to determine the radiative/conductive heat flux, thermal conductivity, and optical properties of slag. The results showed that the mold/slag interfacial thermal resistance decreases with the increasing temperature of slag surface at the mold side, and then reaches the minimum when the slag surface is the hottest, and finally increases slightly with further increase in slag crystallization. In addition, the radiative heat flux decreases with the increasing depth of radiation propagating into the slag. While the amount of heat of radiation lost is being converted to produce an additional radiative heat source to heat the slag, the increase in the conductive heat flux in the slag is realized. Furthermore, the apparent transmittivity is obtained as 0.63 for the glassy slag disk and as 0.41 for the partially crystallized slag disk. Besides, when mold heat flux decreases from the maximum to a saturation value due to the further slag crystallization, the corresponding apparent transmittivity of slag disk decreases from 0.58 to 0.41, and the ratio of the heat across the slag disk by radiation decreases from 67.3 to 50.0 pct.
Fiber orientation distribution (FOD) in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for glass fiber (GF), carbon fiber (CF), and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varied with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.
Injection molded parts are driven down in size and weight especially for electronic applications. In this work, an investigation was carried out on the process of injection molding of thin iPP samples and on the morphology of these parts. Melt flow in the mold cavity was analyzed and described with a mathematical model. Influence of mold temperature and injection pressure was analyzed. Samples orientation was studied using optical microscopy.
This project aimed to integrate, optimize, and validate the fiber orientation and length distribution models previously developed and implemented in the Autodesk® Simulation Moldflow® Insight (ASMI) software package for injection-molded long-carbon-fiber (LCF) thermoplastic composite structures. The project was organized into two phases. Phase 1 demonstrated the ability of the advanced ASMI package to predict fiber orientation and length distributions in LCF/polypropylene (PP) and LCF/polyamide-6, 6 (PA66) plaques within 15% of experimental results. Phase 2 validated the advanced ASMI package by predicting fiber orientation and length distributions within 15% of experimental results for a complex three-dimensional (3D) Toyota automotive part injection-molded from LCF/PP and LCF/PA66 materials. Work under Phase 2 also included estimate of weight savings and cost impacts for a vehicle system using ASMI and structural analyses of the complex part. The present report summarizes the completion of Phases 1 and 2 work activities and accomplishments achieved by the team comprising Pacific Northwest National Laboratory (PNNL); Purdue University (Purdue); Virginia Polytechnic Institute and State University (Virginia Tech); Autodesk, Inc. (Autodesk); PlastiComp, Inc. (PlastiComp); Toyota Research Institute North America (Toyota); Magna Exteriors and Interiors Corp. (Magna); and University of Illinois. Figure 1 illustrates the technical approach adopted in this project that progressed from compounding LCF/PP and LCF/PA66 materials, to process model improvement and implementation, to molding and modeling LCF/PP and LCF/PA66 plaques. The lessons learned from the plaque study and the successful validation of improved process models for fiber orientation and length distributions for these plaques enabled the project to go to Phase 2 to mold, model, and optimize the 3D complex part.
Engineering of ductile, tough and thermal resistant PLA-based materials requires blending of PLA with other constituents by reactive twin-screw co-rotating extrusion to achieve compounds with adequate thermo-mechanical properties. Then, the compound of the polymeric blends must be melt processed to the final shape with an additional technology, namely the injection molding. The two-stage process the polymeric blends must undergo and the different rheological properties the blends must feature to be suitable to the different processing steps make extremely difficult to engineer the material. Extrusion compounding requires high viscous materials low melt flow index (MFI), while injection molding requires materials with low viscosity (high MFI). To overcome these shortcomings, this manuscript deals with the design of novel biodegradable PLA-based blends that rely on mixing PLA grades with different MFI (i.e. very low for extrusion and high for injection molding), each chosen to feature the rheological characteristics needed for each step of the two-stage transformation process. The ratio of the two PLA-grades inside the blends was the matter of the present investigation. The blends were subsequently tested for the manufacturing of single-use biodegradable and thermal resistant injection molded small cups, specifically designed for brewing of hot beverages. Lastly, the thermo-mechanical performance of the as-is and annealed cups were studied. Experimental evidences show blending of two-different grades of PLA is a promising route to formulate low impact polymeric materials suitable for demanding packaging solutions.
The effect of Li{sub 2}O content on the behavior of melting, crystallization, and molten structure for CaO-Al{sub 2}O{sub 3}-based mold fluxes was investigated in this article, through use of single hot thermocouple technology (SHTT), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and X-ray diffraction (XRD). The SHTT results showed that the melting temperature range of the designed mold fluxes decreases and the crystallization of mold fluxes is inhibited first and then becomes enhanced when the Li{sub 2}O content increases from 1 to 6 mass pct. The FTIR and Raman spectroscopy results suggested that Li{sub 2}O could release O{sup 2−} ions to break the complex Al-O-Al structural unit into Al-O{sup −} structure. Meanwhile, Li{sub 2}O could also stabilize the structural unit of Si-O-Al by link aluminate and Q{sub 0}{sup Si} structure through providing Li{sup +} ions to merge into the network and compensate for the charges between Al{sup 3+} and Si{sup 4+}. Besides, the XRD results indicated that the precipitation of LiAlO{sub 2} in molten slag would enhance the crystallization behavior of mold flux when Li{sub 2}O content is over 4.5 mass pct.
Ceramic molds containing the ZrSiO{sub 4}/SiO{sub 2} primary face coat with and without addition of cobalt aluminate were produced. After firing, the surface and the cross sections of the face coats were subjected to detailed characterization using XRD, SEM and EDS. The interaction between the mold systems and 0.9C-6W-5Mo-4Cr-2V high-speed steel was studied during the gravity and vacuum investment casting. During casting, the isostructural transformation of the initial ZrSiO{sub 4} filler occurred. For the mold without addition of the cobalt aluminate, two different types of interaction products [multicomponent phase containing O, Al, Zr, Fe, W and V and (Fe, W,Mo,Cr){sub 2}Al{sub 2}O{sub 6})] were revealed. An interaction layer of a depth in the range of 5-30 μm was thoroughly studied after casting into the mold containing the cobalt aluminate. Addition of the cobalt aluminate into the ceramic system provided significant refinement of the high-speed steel microstructure.
Composite joining typically involves multiple steps, such as drilling and surface treatment, as part of the manufacturing process, which leads to low throughput and long cycle times. In the present study, we demonstrated a macro-level mechanical interlocking (MI) based, rapid joining technique to assemble additively manufactured compression molded (AMCM) panels, enabling the production of parts larger than the mold dimensions. Composite panels made of 20 wt% short carbon fiber reinforced acrylonitrile butadiene styrene (CF/ABS) were joined using MI features of various geometries, namely tree (TR), dovetail (Dov), rectangle 2 (Rect2), and rectangle 1 (Rect1), and their in-plane strength was evaluated. The resultant strength of the tested MI joints reached up to 74 % of the baseline tensile strength (i.e., the ‘no joint’ case). Observations from optical and scanning electron microscopy revealed inadequate polymer diffusion between the adherends, indicating that the joint strength was primarily derived from mechanical interlocking. Additionally, the fracture surfaces exhibited stress-whitening marks, which were characterized using differential scanning calorimetry (DSC). The increase in melting enthalpy suggested local stretching of polymer chains due to MI. Finite element analysis (FEA) indicated that the Rect1 MI feature, which generated the lowest stress concentration, outperformed the others in terms of joint strength, achieving 42 MPa. As a demonstration of the MI joining method, a battery box tray measuring 108 cm × 34 cm using a mold with an effective dimension of 36 cm × 34 cm successfully manufactured, resulting in a part with an area three times larger than the mold. In conclusion, this study presents a promising approach to improving composite joining techniques while minimizing production complexities.
Oak Ridge National Laboratory (ORNL) has developed a highly automated manufacturing process for thermoplastic composites that combines the benefits of Additive Manufacturing and Compression Molding (AM-CM) to produce high-performance functional composite structures at automotive production rates. Here, the AM-CM process creates highly precise preforms by additively placing extruded fiber-filled polymers (with controlled fiber orientations and multi-material configurations) in the desired mold location before undergoing a secondary compression molding process immediately before the preform cools down. Preforms can be in the form of short, long-chopped, or continuous fiber-filled thermoplastic polymers (e.g., CF/GF-filled ABS, PC, LM-PAEK, etc.). The AM-CM process combines the benefits of controlled fiber alignment, that is only achievable in AM-printed parts with the classical CM process, which eliminates porosity and good surface finish. A preform created using AM-CM can integrate various materials to enable additional architectural functionalities, including over-molding, selective stiffening, and the incorporation of electrically or thermally conductive channels. All these advantages come with a fast part production cycle time. The AM-CM process can manufacture multi-material, multi-functional parts in under 3 min, starting from raw material (pellets) to the final product. The novel AM-CM process offers superior microstructural control and enhanced multi-functionality previously unattainable with any other traditional high-rate thermoplastic composite manufacturing method. This work covers the manufacturing concept, system development, materials and applications of AM-CM process in detail.