Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mass loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

AE33 Aethalometer Records at RMBL [AMF2] from April 2022 to October 2023

The dataset presents atmospheric mass loadings of black carbon (BC) and brown carbon (BrC), during the Surface Atmosphere Integrated Field Laboratory (SAIL) campaign that took place from 2021 – 2023 in Gothic, CO. A Magee Scientific aethalometer (model AE33) was deployed at the Rocky Mountain Biological Laboratory, 200 m north of AMF2 to monitor mass loadings of optically absorbing aerosols. The instrument inlet was equipped with a BGI SCC 1.829 ambient cyclone with a particle cutoff of 2.5 μm and placed 5 m above ground level. The dataset reports hour-resolved BC mass loadings at 370, 470, 520, 590, 660, 880, and 950 (BC370, BC470, BC 520, BC590, BC660, BC880, BC950 in ng/m3) reported by the instrument built-in algorithm, which calculates mass loadings from the rate of change of the attenuation of light transmitted through the aerosol-laden filter. BC880 is the operationally defined reference of the BC concentration. Hour-resolved absorbance at each wavelength were calculated from their respective mass absorption cross-section in inverse megameters (Mm-1). The absorption Angstrom exponent (AAE) for BrC and BC were calculated for each hour. BrC AAE (AAE_BrC) was calculated from the slope of Log(wavelength) versus Log(absorbance) based on the measurements at 370, 470, and 520 nm. BC AAE (AAE_BrC) was calculated from the slope of Log(wavelength) versus Log(absorbance) based on the measurements at 590, 660, 880, and 950 nm. The aethalometer record spans time periods of 4/5/2022 – 10/3/2022 and 12/8/2022 – 10/9/2023. The ambient CO2 concentration recorded by a Vaisala CARBOCAP carbon dioxide probe GMP343 is also reported in ppm.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1987

Displacements of the earth's surface due to atmospheric loading - Effects of gravity and baseline measurements

Atmospheric mass loads and deforms the earth's crust. By performing a convolution sum between daily, global barometric pressure data and mass loading Green's functions, the time dependent effects of atmospheric loading, including those associated with short-term synoptic storms, on surface point positioning measurements and surface gravity observations are estimated. The response for both an oceanless earth and an earth with an inverted barometer ocean is calculated. Load responses for near-coastal stations are significantly affected by the inclusion of an inverted barometer ocean. Peak-to-peak vertical displacements are frequently 15-20 mm with accompanying gravity perturbations of 3-6 micro Gal. Baseline changes can be as large as 20 mm or more. The perturbations are largest at higher latitudes and during winter months. These amplitudes are consistent with the results of Rabbel and Zschau (1985), who modeled synoptic pressure disturbances as Gaussian functions of radius around a central point. Deformation can be adequately computed using real pressure data from points within about 1000 km of the station. Knowledge of local pressure, alone, is not sufficient. Rabbel and Zschau's hypothesized corrections for these displacements, which use local pressure and the regionally averaged pressure, prove accurate at points well inland but are, in general, inadequate within a few hundred kilometers of the coast.

Van Dam, T. M.↗
DOE OSTI2021

Demonstration of Defense Waste Processing Facility (DWPF) Higher Fissile Content Glass

The Accelerated Basin De-inventory (ABD) Program has been proposed as an alternative for future spent nuclear fuel (SNF) and nuclear material processing at the Savannah River Site (SRS). This approach would change the baseline H-Canyon (HCAN), Concentrate, Storage, and Transfer Facility (CSTF), and Defense Waste Processing Facility (DWPF) operations. The ABD Program would require that all domestic and foreign research reactor SNF currently at SRS be dissolved, stored, and then transferred to CSTF without the recovery of uranium. Preliminary assessments in the ABD Program plan have shown that ~5000 extra SRS high-level waste (HLW) canisters would be produced if the fissile mass loading remains at the current 897 g/m 3 limit; however, increasing the limit to 2500 g/m 3 would result in ~520 extra canisters. Thus, the ABD Program plan requires an increase of the DWPF fissile mass loading limit to 2500 g/m 3 to minimize canister production. DWPF considers the following isotopes in the calculation of fissile mass loading: U-233, U-235, Pu-239 and Pu-241.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1983

Heavy ions in the outer Kronian magnetosphere

The possible sources of the cold plasma observed in the outer magnetosphere of Saturn are analyzed. On the basis of the O(+)-H charge exchange species-specific loss mechanism, as well as abundance and rate considerations, it is concluded that the dominant heavy ion populating the equatorial outer magnetosphere is that of atomic nitrogen. Possible sources of hot plasma are also discussed, as are the inhibition of corotation by mass loading and the radial variation of composition. It is found that the observed deviations from corotation and current mass loading estimates indicate either a somewhat higher ionospheric conductance than is implied by the UVS and RSS measurements, or an overestimate of mass loading. It is suggested that the plasma gap observed by Voyager 1 outbound may be associated with a composition change.

Eviatar, A.↗
NASA NTRS2021

Seasonal Glacier and Snow Loading in Svalbard Recovered from Geodetic Observations

We processed time series from seven Global Navigation Satellite System (GNSS) stations and one Very Long Baseline Interferometry (VLBI) station in Svalbard. The goal was to capture the seasonal vertical displacements caused by elastic response of variable mass load due to ice and snow accumulation. We found that estimates of the annual signal in different GNSS solutions disagree by more than 3 mm which makes geophysical interpretation of raw GNSS time series problematic. To overcome this problem, we have used an enhanced Common Mode (CM) filtering technique. The time series are differentiated by the time series from remote station BJOS with known mass loading signals removed a priori. Using this technique, we have achieved a substantial reduction of the differences between the GNSS solutions. We have computed mass loading time series from a regional Climatic Mass Balance (CMB) and snow model that provides the amount of water equivalent at a 1 km resolution with a time step of 7 days. We found that the entire vertical loading signal is present in data of two totally independent techniques at a statistically significant level of 95%. This allowed us to conclude that the remaining errors in vertical signal derived from the CMB model are less than 0.2 mm at that significance level. Refining the land water storage loading model with a CMB model resulted in a reduction of the annual amplitude from 2:1 mm to 1:1 mm in the CM filtered time series, while it had only a marginal impact on raw time series. This provides a strong evidence that CM filtering is essential for revealing local periodic signals when a millimetre level of accuracy is required.

H P Kierulf↗
NASA NTRS2003

Irreversible Entropy Production in Two-Phase Mixing Layers

This report presents a study of dissipation (irreversible production of entropy) in three-dimensional, temporal mixing layers laden with evaporating liquid drops. The purpose of the study is to examine the effects of evaporating drops on the development of turbulent features in flows. Direct numerical simulations were performed to analyze transitional states of three mixing layers: one without drops, and two that included drops at different initial mass loadings. Without drops, the dissipation is essentially due to viscous effects. It was found that in the presence of drops, the largest contribution to dissipation was made by heating and evaporation of the drops, and that at large length scales, this contribution is positive (signifying that the drops reduce turbulence), while at small scales, this contribution is negative (the drops increase turbulence). The second largest contribution to dissipation was found to be associated with the chemical potential, which leads to an increase in turbulence at large scales and a decrease in turbulence at small scales. The next smaller contribution was found to be that of viscosity. The fact that viscosity effects are only third in order of magnitude in the dissipation is in sharp contrast to the situation for the mixing layer without the drops. The next smaller contribution - that of the drag and momentum of the vapor from the drops - was found to be negative at lower mass loading but to become positive at higher mass loading.

Okongo, Nora↗
DOE OSTI2023

SILCC – VII. Gas kinematics and multiphase outflows of the simulated ISM at high gas surface densities

ABSTRACT We present magnetohydrodynamic (MHD) simulations of the star-forming multiphase interstellar medium (ISM) in stratified galactic patches with gas surface densities Σgas = 10, 30, 50, and 100 $\mathrm{M_\odot \, pc^{-2}}$. The silcc project simulation framework accounts for non-equilibrium thermal and chemical processes in the warm and cold ISM. The sink-based star formation and feedback model includes stellar winds, hydrogen-ionizing UV radiation, core-collapse supernovae, and cosmic ray (CR) injection and diffusion. The simulations follow the observed relation between Σgas and the star formation rate surface density ΣSFR. CRs qualitatively change the outflow phase structure. Without CRs, the outflows transition from a two-phase (warm and hot at 1 kpc) to a single-phase (hot at 2 kpc) structure. With CRs, the outflow always has three phases (cold, warm, and hot), dominated in mass by the warm phase. The impact of CRs on mass loading decreases for higher Σgas and the mass loading factors of the CR-supported outflows are of order unity independent of ΣSFR. Similar to observations, vertical velocity dispersions of the warm ionized medium (WIM) and the cold neutral medium (CNM) correlate with the star formation rate as $\sigma _\mathrm{z} \propto \Sigma _\mathrm{SFR}^a$, with a ∼ 0.20. In the absence of stellar feedback, we find no correlation. The velocity dispersion of the WIM is a factor ∼2.2 higher than that of the CNM, in agreement with local observations. For $\Sigma _\mathrm{SFR} \gtrsim 1.5 \times 10^{-2}\, \mathrm{M}_\odot \, \mathrm{yr}^{-1}\, \mathrm{kpc}^{-2}$ the WIM motions become supersonic.

Astronomy & Astrophysics↗
DOE OSTI2021

Seasonal Seismicity in the Lake Biwa Region of Central Japan Moderately Modulated by Lake Water Storage Changes

Seasonal seismicity in Japan has been observed and attributed to variations induced by hydrological loading, as well as atmospheric and pore-fluid pressure. We examine the seasonal variations of crustal (<15 km depth) and low magnitude (M < 4.5) earthquakes in central Japan near the Biwako-Seigan Fault Zone (BSFZ), and analyze their correlation with the annual hydrological cycle of nearby Lake Biwa, the largest freshwater lake in Japan. The 2002–2018 lake water storage is estimated using water-level gauge and satellite altimetry data. Regional surface mass loading from soil moisture and snow predicted by the Global Land Data Assimilation System is used to augment the lake mass variation. We compute the stress and stressing-rate changes induced by the surface mass loading from lake storage, snow, and soil moisture at seismogenic depth (10 km) along the BSFZ using a finite element model incorporating a 3D Earth structure. The results show that seasonal surface mass loading generates 1–5 kPa peak-to-peak Coulomb stress change and 2.5–15 kPa/year stressing-rate variations on the fault segments along the BSFZ. Two of the four fault segments present significant correlation between local seismicity rate and loading-derived stress and/or stressing rate changes. Among the hydrological load components, lake water, snow, and soil moisture exhibit different annual phases, and the lake water storage dominates the total annual stress changes. Our analysis indicates that seasonal surface hydrological loads, especially lake water variations, modulate the seismicity rate along the BSFZ in central Japan.

58 GEOSCIENCES↗
DOE OSTI2021

Nanocolumnar Pt:Ni Alloy Thin Films by High Pressure Sputtering for Oxygen Reduction Reaction

Self-supported nanocolumnar Pt:Ni thin films (TFs) with varying Pt:Ni atomic ratios and Pt mass loadings were produced on a microporous layer (MPL)-like surface composed of carbon particles by high pressure sputtering and examined as oxygen reduction reaction (ORR) electrocatalysts for polymer electrolyte membrane fuel cells. Cauliflower-like microstructures were observed from scanning electron microscopy imaging. Various Pt:Ni atomic ratios were obtained by simply changing the relative deposition power between Pt and Ni source and investigated by X-ray diffraction and quartz crystal microbalance analysis. Additionally, electrochemical characterization of the Pt:Ni-TF/MPL-like-layer/glassy-carbon samples was conducted through benchtop cyclic voltammetry and rotating disk electrode measurements. The electrochemically active surface area (ECSA) was found to be between 22–42 m 2 g -1 for different Pt:Ni atomic ratios. Lower Pt mass loadings exhibited a higher ECSA and the catalytic activity of all Pt:Ni ratios increased with the increase in Pt mass loading. The ORR activity of the Pt:Ni-TFs increased in the order of 3:1 < 1:1 < 1:3 with exhibiting a specific activity of 1781 μA cm -2 and mass activity of 0.66 A mg -1 for the Ni-rich film with 1:3 ratio. The catalytic performance of Pt:Ni-TFs were higher than traditional high surface area carbon supported Pt nanoparticles, elemental Pt nanorods, and Pt-Ni nanorods.

08 HYDROGEN↗
NASA NTRS1987

Corotation lag limit on mass-loss rate from Io

Considering rapid escape of H2O from Io during an early hot evolutionary epoch, an H2O plasma torus is constructed by balancing dissociation and ionization products against centrifugally driven diffusion, including for the first time the effects of corotation lag resulting from mass loading. Two fundamental limits are found as the mass injection rate increases: (1) an 'ignition' limit of 1.1 x 10 to the 6th kg/s, beyond which the torus cannot ionize itself and photoionization dominates; and (2) the ultimate mass loading limit of 1.3 x 10 to the 7th kg/s, which occurs when neutrals newly created by charge exchange and recombination cannot leave the torus, thereby bringing magnetospherically driven transport to a halt. Connecting this limit with the variations of Io's temperature in its early evolution epoch gives an estimate of the upper limit on the total mass loss from Io, about 3.0 x 10 to the 20th kg (for high-opacity nebula) and about 8.9 x 10 to the 20th kg (for low-opacity nebula). These limits correspond to eroding 8 km and 22 km of H2O from the surface. It is concluded that compared to the other Galilean satellites, Io was created basically dry.

Huang, T. S.↗
NASA NTRS2006

Scalar Dissipation Modeling for Passive and Active Scalars: a priori Study Using Direct Numerical Simulation

Transitional databases from Direct Numerical Simulation (DNS) of three-dimensional mixing layers for single-phase flows and two-phase flows with evaporation are analyzed and used to examine the typical hypothesis that the scalar dissipation Probability Distribution Function (PDF) may be modeled as a Gaussian. The databases encompass a single-component fuel and four multicomponent fuels, two initial Reynolds numbers (Re), two mass loadings for two-phase flows and two free-stream gas temperatures. Using the DNS calculated moments of the scalar-dissipation PDF, it is shown, consistent with existing experimental information on single-phase flows, that the Gaussian is a modest approximation of the DNS-extracted PDF, particularly poor in the range of the high scalar-dissipation values, which are significant for turbulent reaction rate modeling in non-premixed flows using flamelet models. With the same DNS calculated moments of the scalar-dissipation PDF and making a change of variables, a model of this PDF is proposed in the form of the (beta)-PDF which is shown to approximate much better the DNS-extracted PDF, particularly in the regime of the high scalar-dissipation values. Several types of statistical measures are calculated over the ensemble of the fourteen databases. For each statistical measure, the proposed (beta)-PDF model is shown to be much superior to the Gaussian in approximating the DNS-extracted PDF. Additionally, the agreement between the DNS-extracted PDF and the (beta)-PDF even improves when the comparison is performed for higher initial Re layers, whereas the comparison with the Gaussian is independent of the initial Re values. For two-phase flows, the comparison between the DNS-extracted PDF and the (beta)-PDF also improves with increasing free-stream gas temperature and mass loading. The higher fidelity approximation of the DNS-extracted PDF by the (beta)-PDF with increasing Re, gas temperature and mass loading bodes well for turbulent reaction rate modeling.

scalar dissipation modeling↗
NASA NTRS2006

Development of Handling Qualities Criteria for Rotorcraft with Externally Slung Loads

Piloted simulations were performed on the NASA-Ames Vertical Motion Simulator (VMS) to explore handling qualities issues for large cargo helicopters, particularly focusing on external slung load operations. The purpose of this work was based upon the need to include handling qualities criteria for cargo helicopters in an upgrade to the U.S. Army's rotorcraft handling qualities specification, Aeronautical Design Standard-33 (ADS-33E-PRF). From the VMS results, handling qualities criteria were developed fro cargo helicopters carrying external slung loads in the degraded visual environment (DVE). If satisfied, these criteria provide assurance that the handling quality rating (HQR) will be 4 or better for operations in the DVE, and with a load mass ratio of 0.33 or less. For lighter loads, flying qualities were found to be less dependent on the load geometry and therefore the significance of the criteria is less. For heavier loads, meeting the criteria ensures the best possible handling qualities, albeit Level 2 for load mass ratios greater than 0.33.

Hoh, Roger H.↗
NASA NTRS1983

Escape and ionization of atomic oxygen from Io

Model calculations of the neutral O cloud of Io, based on atom-electron-impact excitation and ionization processes in the plasma torus, are presented. The model is quantitatively anchored to the 6300-A O I emission intensity observations of Brown (1981), and uses a plasma temperature and density structure based on Voyager 1 and 2 and EUV data. Parameters predicted by the model include satellite emission flux = 1.5 x 10 to the 9th/sq cm sec, ion-loading rate = 6.2 x 10 to the 26th ions/sec, O mass-loading rate = 16.6 kg/sec, and O ion-energy input rate = 2.7 x 10 to the 10th W. The spatial morphologies of the parameters are shown. Rough estimates obtained by accounting for a neutral S cloud and plasma-torus charge-exchange reactions include O source flux = 1.2 x 10 to the 10th/sq cm sec, ion-loading rate = 4.0 x 10 to the 27th ions/sec, ion-diffusive-loss time = 200 days, plasma mass-loading rate = 150 kg/sec, satellite mass-loss rate = 270 kg/sec, and maximum ion-energy input = 4 x 10 to the 11th W.

Smyth, W. H.↗
NASA NTRS2001

Iogenic Plasma and its Rotation-Driven Transport in Jupiter's Magnetosphere

Model calculations are reported for the Iogenic plasma source created by atomic oxygen and sulfur above Io's exobase in the corona and extended clouds (Outer Region). On a circumplanetary scale, two-dimensional distributions produced by integrating the proper three dimensional rate information for electron impact and charge exchange processes along the magnetic field lines are presented for the pickup ion rates, the net-mass and total-mass loading rates, the mass per unit magnetic flux rate, the pickup conductivity, the radial pickup current, and the net-energy loading rate for the plasma torus. All of the two-dimensional distributions are highly peaked at Io's location and hence highly asymmetric about Jupiter. The Iogenic plasma source is also calculated on a much smaller near-Io scale to investigate the structure of the highly peak rates centered about lo's instantaneous location. The Iogenic plasma source for the Inner Region (pickup rates produced below Io's exobase) is, however, expected to be the dominant source near lo for the formation of the plasma torus ribbon and to be a comparable source, if not a larger contributor, to the energy budget of the plasma torus, so as to provide the necessary power to sustain the plasma torus radiative loss rate.

Smyth, William H.↗
DOE OSTI2020

Prediction for Pressure Differential Across HEPA Filter Media Based on Media Characteristics and Particle Size Distribution

A new method for predicting the pressure drop across High Efficiency Particulate Air (HEPA) filter media is proposed based upon mass deposited onto the filter and known physical characteristics of the filter media. Detailed are the methods used in conjunction with current filter loading models to predict the pressure drop, as well as tests conducted to validate the methods. The benefit of a prediction model for practical use lies in the manufacturing and service life of nuclear grade HEPA filters. HEPA filters for use in nuclear facilities have a prescribed expiration date and a maximum allowable operating pressure drop. Therefore, the ability to predict the pressure drop across a filter and relate it to an expected length of service time can enable a reduction in wasted filters. This will allow for more informed decisions to be made based upon the dictated life cycle of the filters. Also, understanding and predicting how the pressure drop of HEPA filter media behaves as a function of physical characteristics and loaded mass can assist in future design and manufacturing of filter media. Currently, most existing pressure drop models are either computationally based or analytical methods relying on data gathered during tests. Neither are practical for prediction; the computational methods are difficult to implement, and the current analytical methods are more useful as tools for analysis. The current analytical model developed by Bergman et al. is based upon the pressure drop from each media fiber and modeling the deposited particles as newly formed fibers. Using Bergman's model and the media properties, air properties, and known aerosol particle size distribution, a pressure drop curve as a function of loaded mass can be created. This curve implies initial loading in the depth of the filter media with a transition to pure surface loading on the filter face, and a sensitivity to an evolving particle size distribution as mass continues to load onto the filter. To implement the predictive model, knowledge of the mean filter fiber diameter and porosity of the filter media is required. Traditionally, the mean fiber diameter is calculated as an effective diameter from prior media testing, however, in this study a Scanning Electron Microscope (SEM) technique is used to acquire this variable. Validation of the predictive model is provided by flat sheet media tests under a controlled environment with a measured particle size distribution of the challenge aerosol and shows reasonable preliminary agreement.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1977

Effect of bow-type initial imperfection on the buckling load and mass of graphite-epoxy blade-stiffened panels

A structural synthesis computer code which accounts for first order effects of an initial bow and which can be used for sizing stiffened composite panels having an arbitrary cross section is used to study graphite blade-stiffened panels. The effect of a small initial bow on both the load carrying ability of panels and on the mass of panels designed to carry a specified load is examined. Large reductions in the buckling load caused by a small initial bow emphasize the need for considering a bow when a panel is designed.

Stroud, W. J.↗
NASA NTRS1986

Ground-based observations of the Jupiter plasma torus

The intensity variation of (SIII) 9531 A emission from the hot plasma torus of Jupiter was measured using a scanning Fabry-Perot spectrometer. During the observational period, which covered 43 rotations of Jupiter, the (SIII) intensities showed a periodic variation consistent with a zone of enhanced emission approximately 90 deg in longitude, rotating with a period of 10.2 hours, or 2.8% longer than Jupiter's rotational period. Dessler developed a theoretical model of account for Jovian magnetospheric phenomena that differ in repetition period by 3%. In his model, periodic modulation of magnetospheric phenomena is controlled in part by the spin period of magnetic features below the surface of the planet. The differing observed periods are then due to differential rotation of the subsurface magnetic features at different latitudes. A consequence that follows from this concept of differential rotation of the internal planetary magnetic field is that not all the apparent subcorotational plasma flow in the torus is caused by plasma mass loading, as described by Hill and his associates. As a result, the mass loading required to produce the residual subcorotational flow is less than previously estimated.

Scherb, F.↗
NASA NTRS1997

Calibration of the QCM/SAW Cascade Impactor for Measurement of Ozone in the Stratosphere

The Quartz Crystal Microbalance Surface Acoustic Wave (QCM/SAW) cascade impactor collects size-fractionated distributions of aerosols on a series of 10 MHz quartz crystals and employs SAW devices coated with chemical sensors for gas detection. Presently, we are calibrating the ER-2 certified QCM/SAW cascade impactor in the laboratory for the detection of ozone. Experiments have been performed to characterize the QCM and SAW mass loading, saturation limits, mass frequency relationships, and sensitivity. We are also characterizing sampling efficiency by measuring the loss of ozone on different materials. There are parallel experiments underway to measure the variations in the sensitivity and response of the QCM/SAW crystals as a function of temperature and pressure. Results of the work to date will be shown.

Wright, Cassandra K.↗