SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
BEE will have the ability to archive, clone, and re-run workflows that have been previously executed. This will enable reproducibility and portability of scientific workflows both within and between DOE facilities.
Construction and deployment of the experimental testbed encountered scheduling delays, and completion was subsequently further delayed by curtailment of LANL operations due to the COVID–19 pandemic. Between March and October, LANL was in a state of “Limited Operations” such that only certain “mission–critical” work was performed with approximately 25% on–site staffing. In spite of this, much of the lab space preparation was executed and the five initial model house” units were constructed and installed during this period. Still, the pace of construction was impacted by difficulty in coordinating personnel and minimizing contact between workers.
The Sandia National Laboratories (SNL) staff is meeting the requirements of the Nuclear Fuel Cycle and Supply Chain (NFCSC) Quality Assurance Program Document (QAPD). Each of the 5 NFCSC FY 20 packages for SNL were reviewed. None of the 5 packages had incorrect QRL categories. No major corrective actions are assigned. Additional and minor PICS:NE checkbox errors may exist, but none were identified in this assessment. Training is now also geared to encourage WPMs to take credit for optional technical reviews by considering setting the QRL level to 3. This is because when the level is set to 4, the PICS:NE system does not provide fields for review information. Finally, training in the NFCSC QAPD has been delivered as always to WPMs.
This document summarizes the progress made by Oak Ridge National Laboratory (ORNL) in collaboration with the University of Michigan on “Rapid Simulation of Irradiation Damage in PWR Internals,” a research project led by the University of Michigan and supported by US Department of Energy Office of Nuclear Energy Nuclear Science User Facilities Consolidated Innovative Nuclear Research program. In this reporting period, samples that were exposed to combined neutron and ion irradiation were prepared and shipped to the University of Michigan for further analysis. This report summarizes the specimen preparation performed at ORNL’s Low Activation Materials Development and Analysis facility. The benchmarking work of microstructural characterization on reactor-irradiated samples with different dose levels was completed.
As part of its mission to ensure the reliability of the nation's nuclear weapons stockpile, the NNSA has funded a broad range of projects to characterize the mass of material ejected from shocked metal surfaces with special emphasis placed on determining the size distribution of macroscopic "ejecta" particles. Substantial work has been done for particles with diameters down to roughly 1 μm, but little data is available for smaller particles, and no data exist for the amount of atomic-scale ejecta produced in such dynamic environments. Such data are important due to the implications for weapons systems behavior but also for distinguishing between different potential ejecta production mechanisms, such as Rayleight-Taylor instability or the shallow-bubble-collapse phenomenon recently proposed by G. Maskally.
The supercritical carbon dioxide (sCO 2 ) Brayton cycle is a promising candidate for future nuclear reactors due to its ability to improve power cycle energy conversion efficiency. The sCO 2 Brayton cycle can operate with an efficiency of 45-50% at operating temperatures of 550-700 C. One of the greatest hurdles currently faced by sCO 2 Brayton cycles is the extreme corrosivity of sCO 2 . This affects the longevity of the power cycle and thus the levelized cost of electricity. Past studies have shown that sCO 2 corrosion occurs through the formation of metal carbonates, oxide layers, and carburization, and alloys with Cr, Mo and Ni generally exhibit less corrosion. While stainless steels may offer sufficient corrosion resistance at the lower range of temperatures seen by the sCO 2 Brayton cycles, more expensive alloys such as Inconel and Haynes are typically needed for the higher temperature regions. This study investigates the effects of corrosion on the Haynes 230 alloy, focusing on changes in the mechanical properties.
Polysiloxane foams utilized for stockpile applications experience changes over time induced by exposure to thermal, radiative, and mechanical stresses. The interplay of these stresses can lead to chemical and/or physical changes in the polymer, such as compression set and material degradation over time. Understanding the mechanisms of material aging and identifying material degradation prior to failure are critical in maintaining the integrity of the nuclear stockpile. Our prior work using solid-state NMR spectroscopy has shown that we can observe signatures of thermal, radiative, and mechanical aging of silicone elastomers using differences in NMR parameters such as relaxation (T1 and T2). However, most of our measurements have been on bulk samples and have only provided an average aging behavior of each sample. Here, we have used magnetic resonance imaging (MRI) to provide relaxation-weighted images that are a metric of structural heterogeneity (cross-link density) in polymers across multiple length scales. In addition, the larger sample size that can be accommodated in animal MRI scanners has the potential to make the technique adaptable to detecting heterogeneities whole parts.
This work involves the creation of the Cloud Launcher, a new subcomponent of BEE, and the extension of the BEETaskManager to run on Cloud systems. BEE will be able to interact with the Google Compute Engine and OpenStack cloud APIs to set up simple Cloud clusters for launching HPC job scripts. BEE will use existing functionality to launch jobs that previously could only be launched on HPC systems. The BEETaskManager will handle launching tasks on the Cloud cluster.
Develop a new graphical BEE client for managing workflows.
Polymers such as PTFE (polytetrafluorethylene or Teflon), EPDM (ethylene propylene diene monomer) rubber, FKM fluoroelastomer (Viton), Nylon 11, Nitrile butadiene (NBR) rubber, hydrogenated nitrile rubber (HNBR) and perfluoroelastomers (FF_202) are commonly employed in super critical CO 2 (sCO2) energy conversion systems. O-rings and gaskets made from these polymers face stringent performance conditions such as elevated temperatures, high pressures, pollutants, and corrosive humid environments. In FY 2019, we conducted experiments at high temperatures (100°C and 120°C) under isobaric conditions (20 MPa). Findings showed that elevated temperatures accelerated degradation of polymers in sCO2, and that certain polymer microstructures are more susceptible to degradation over others. In FY 2020, the focus was to understand the effect of sCO2 on polymers at low (10 MPa) and high pressures (40 MPa) under isothermal conditions (100°C). It was clear that the same selectivity was observed in these experiments wherein certain polymeric functionalities showed more propensity to failure over others. Fast diffusion, supported by higher pressures and long exposure times (1000 hours) at the test temperature, caused increased damage in sCO2 environments to even the most robust polymers. We also looked at polymers under compression in sCO2 at 100°C and 20 MPa pressure to imitate actual sealing performance required of these materials in sCO2 systems. Compression worsened the physical damage that resulted from chemical attack of the polymers under these test conditions. In FY 2021, the effect of cycling temperature (from 50°C to 150°C to 50°C) for polymers under a steady sCO2 pressure of 20 MPa was studied. The aim was to understand the influence of cycling temperatures of sCO2 for typical polymers under isobaric (20 MPa) conditions. Thermoplastic polymers (Nylon, and PTFE) and elastomers (EPDM, Viton, Buna N, Neoprene, FF202, and HNBR) were subjected to 20 MPa sCO2 pressure for 50 cycles and 100 cycles in separate experiments. Samples were extracted for ex-situ characterization at 50 cycles and upon the completion of 100 cycles. Each cycle constituted of 175 minutes of cycling from 50°C to 150°C. The polymer samples were examined for physical and chemical changes by Dynamic Mechanical and Thermal Analysis (DMTA), Fourier Transform Infrared (FTIR) spectroscopy, and compression set. Density and mass changes immediately after removal from test were measured for degree of swell comparisons. Optical microscopy techniques and micro computer tomography (micro CT) images were collected on select specimens. Evaluations conducted showed that exposures to super-critical CO2 environments resulted in combinations of physical and/or chemical changes. For each polymer, the dominance of cycling temperatures under sCO2 pressures, were evaluated. Attempts were made to qualitatively link the permanent sCO2 effects to polymer micro- structure, free volume, backbone substitutions, presence of polar groups, and degree of crystallinity differences. This study has established that soft polymeric materials are conducive to failure in sCO2 through mechanisms of failure that are dependent on polymer microstructure and chemistry. Polar pendant groups, large atom substitutions on the backbone are some of the factors that are influential structural factors.
Version 4.0 of the ECP Proxy App Suite is practically unchanged from the previous release. The current set of proxies has proven useful for many aspects of benchmarking and co-design and we see little reason to alter the suite. Although there have been few changes to the ECP suite, the team has been hard at work in other areas. In the area of Machine Learning (ML) we have now created a separate proxy suite dedicated to this scientific applications of ML. The suite includes: miniGAN (Generative Adversarial Networks), miniRL (Reinforcement Learning), CRADL (inline inference), Cosmoflow-Benchmark (Convolutional Neural Network), and MLPerf-DeepCam (Climate Segmentation Benchmark). Section 3 contains more information about these proxies as well as the principles that are guiding the development of the suite. We have surveyed available proxies for several application domains including Computational Fluid Dynamics, Quantum Chemistry, Quantum Computing Simulation, Molecular Dynamics, Monte Carlo Transport, and Density Functional Theory to identify gaps in proxy coverage. Several new proxy apps are either already available or will be released soon to fill these gaps. Section 4 provides full details. Finally, section 5 reports on our continued collaboration with the ECP Continuous Integration (CI) effort to use proxy apps to help identify problems and roadblocks to cross-lab CI. We have also assisted the El Capitan Center of Excellence (COE) to stand up a CI system that will be used to test releases of HPE and AMD software stacks. We hope that the COE effort can serve as a model for ECP by showing how the Proxy App Team can work with AD and ST teams identify critical features, kernels, patterns, etc. and incorporate them into a CI system that will help ensure that Frontier and Aurora will provide those needed capabilities.
This report documents the delivery and installation of rzVernal, a CORAL-2 El Capitan early delivery system deployed on the LLNL Restricted Zone network. Early ASC program users have run codes on the machine in support of application porting for the final El Capitan system which will be deployed at LLNL in CY2023. In addition to the RZ resource, rzVernal, two similar machines, Tioga and Tenaya, have been deployed on the LLNL SRD and Collaboration Zone networks in support of application readiness for the El Capitan platform.
Adhesives and adhesive-bond joints play a critical role in many applications across the national security enterprise. They are ubiquitous and their aging performance can impact the physical and chemical behavior of complex systems. Previously, we have explored the chemical aging behavior of polyurethane adhesives (Halthane 73-18, Halthane 88-3, and Wilethane 44) exposed to varying levels of radiation and identified the primary chemical degradation products. In this work, we expand upon our analysis to understand how the mechanical properties of adhesives-bonded joints behave after radiation exposure.
Polysiloxane foams utilized for stockpile applications experience changes over time induced by exposure to thermal, radiative, and mechanical stresses. The interplay of these stresses can lead to chemical and/or physical changes in the polymer, such as compression set and material degradation over time. Understanding the mechanisms of material aging and identifying material degradation prior to failure are critical in maintaining the integrity of the nuclear stockpile. Our prior work using solid-state NMR spectroscopy has shown that we can observe signatures of thermal, radiative, and mechanical aging of silicone elastomers using differences in NMR parameters such as relaxation (T1 and T2). However, most of our measurements have been on bulk samples and have only provided an average aging behavior of each sample. Here, we have used magnetic resonance imaging (MRI) to provide relaxation-weighted images that are a metric of structural heterogeneity (crosslink density) in polymers across multiple length scales. In addition, the larger sample size that can be accommodated in animal MRI scanners has the potential to make the technique adaptable to detecting heterogeneities in whole parts.
This report introduces a novel characterization tool that can rapidly collect in-situ time-dependent oxide thickness and hydride growth data together with spatial data using while-light interferometry. White-light interferometry is a non-destructive and non-contact optical surface profiling technique for materials characterization that offers excellent lateral and vertical resolution. A depleted uranium sample was used to assess the ability of white-light interferometry to provide quantitative corrosion reaction rates at metal surfaces for by hydriding and oxidation and compare this technique to existing characterization tools for capturing early-stage hydride and oxide growth kinetics.
Abstract not provided.
The sCO 2 system located in 916/160A, Sandia National Laboratories, CA, was constructed in 2014, for testing of materials in the presence of supercritical carbon dioxide (sCO 2 ) at high pressures (up to 3500 psi) and temperatures (up to 650°C). The basic design of the system consists of a thermally insulated IN625 autoclave, a high-pressure supercritical CO 2 compressor, autoclave heaters, temperature controllers, gas manifold, and temperature and pressure diagnostics. This system was modified in 2016 (sCO 2 compressor was removed) to enable corrosion studies with metal alloys in gaseous CO 2 at lower pressure (up to 300 psi) at 500°C. The capability was not used much afterwards until 2020, when preliminary tests using this capability (again without the supercritical CO 2 compressor) involved the exposure of fatigue and tensile specimens of HN 230 and 800H alloys to CO 2 gas for 168 hours in gaseous CO 2 . Using this capability, we finished experiments with low pressure (450 psi/ 3 MPa), high temperature (650°C) exposure of fatigue and tensile specimens of HN 230 and 800H alloys to CO 2 gas for 168 hours. The data from these experiments will be compared to that gathered from experiments performed in 2020 using the tube furnace and presented in a future report. It is to be noted that the tube furnace experiments ran 500-1500 hours, unlike the 168 hours of exposure in the recent experiment. This can help validate the use of the sCO 2 autoclave for both CO 2 and sCO 2 experiments.