Search NASA⌕ Search

SEARCH · Search NASA

Results for “Moments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1922

The Effect of Longitudinal Moment of Inertia upon Dynamic Stability

Free flight tests were carried out to show whether the longitudinal oscillations of a standard S.E.5A airplane are noticeably affected if its longitudinal moment of inertia is increased. These oscillations were taken by means of a self-recording instrument, the airplane having first its ordinary moment of inertia and then one increased by 14 percent. The period of oscillation was slightly longer after the increase of the moment of inertia, but the damping was not affected. Presented here are test results from an investigation to determine the relative performance of a single-cylinder, high-speed, compression-ignition engine when using fuel injection valve nozzles with different numbers, sizes, and directions of round orifices. A spring loaded, automatic injection valve was used. It was centrally located at the top of a vertical disk-type combustion chamber formed between horizontally opposed inlet and exhaust valves of a 5-inch by 7-inch engine. A series of fuel injection valve nozzles with different arrangements of round orifices were tested, starting with orifices so small that impingement on the combustion chamber walls was impossible and increasing beyond the start of impingement. a :A table and curves are presented showing the performance of the engine with different nozzles. The test results are discussed, and some probable reasons given for the variation in performance with different nozzles on the basis of spray distribution.

MOMENTS OF INERTIA - ROYAL AIRCRAFT FACTORY S E 5A↗
NASA NTRS1936

Estimation of moments of inertia of airplanes from design data

A method of determining the moments of inertia of an airplane from design data pertaining to the weights and locations of the component parts is described. The computations required to ascertain the center-of-gravity position are incorporated with the calculations of moments of inertia. A complete set of data and calculations for a modern airplane is given to illustrate the procedure. From a comparison between calculated values and measured values it is believed that the moments of inertia can be estimated within 10 percent by the use of this method.

AIRPLANES - DESIGN↗
NASA NTRS1948

Tests of a Triangular Wing of Aspect Ratio 2 in the Ames 12-foot Pressure Wind Tunnel III : the Effectiveness and Hinge Moments of a Skewed Wing-tip Flap

Results of wind-tunnel tests of a semispan model of a triangular wing of aspect ratio 2 with a skewed wing-tip flap are presented. Lift, drag, pitching-moment, and hinge-moment data are included for subsonic Mach numbers up to 0.95. The flap showed extremely high hinge moments and low effectiveness as a longitudinal control. Although less affected by compressibility, this flap is indicated to be inferior to a constant-chord flap when applied to this triangular wing.

MACH NUMBER EFFECTS - COMPLETE WINGS↗
NASA NTRS1929

The balance of moments and the static longitudinal stability of airplanes

A nomogram is developed which renders it possible by drawing a few lines, to determine: the location of the center of gravity for zero wing and tail moments; the longitudinal dihedral angle; the tail coefficient F(sub h) iota/F(sub t). Moreover there is no difficulty in determining the magnitude of the restoring moment or of the unstable moment.

STABILITY↗
NASA NTRSDate not supplied

Determining Aircraft Moments of Inertia from Flight Test Data

Flight test maneuver design and dynamic modeling techniques were developed for determining aircraft moments of inertia from flight test data. Full nonlinear rigid-body rotational equations of motion were used in the analysis, with aerodynamic moment dependencies modeled by linear expansions in the aircraft states and controls. Aerodynamic parameters were estimated simultaneously with inertia parameters using equation-error modeling applied to flight test data from maneuvers designed specifically for this problem. The approach was demonstrated using a nonlinear F-16 simulation, then applied to a remotely-piloted subscale aircraft flight test. Errors in the aircraft moment of inertia parameters determined from simulated F-16 flight test maneuver data were less than 6 percent compared to the true values in the simulation. Flight test results for the subscale aircraft were within 6 percent of ground-test values obtained using the same aircraft.

moments of inertia↗
NASA NTRSDate not supplied

Determining Aircraft Moments of Inertia from Flight Test Data

Flight test maneuver design and dynamic modeling techniques were developed for determining aircraft moments of inertia from flight test data. Full nonlinear rigid-body rotational equations of motion were used in the analysis, with aerodynamic moment dependencies modeled by linear expansions in the aircraft states and controls. Aerodynamic parameters were estimated simultaneously with inertia parameters using equation-error modeling applied to flight test data from maneuvers designed specifically for this problem. The approach was demonstrated using a nonlinear F 16 simulation, then applied to a remotely piloted subscale aircraft flight test. Errors in the aircraft moment of inertia parameters determined from simulated F-16 flight test maneuver data were less than 6 percent compared to the true values in the simulation. Flight test results for the subscale aircraft were within 6 percent of ground-test values obtained using the same aircraft.

Aircraft Moments of Inertia↗
NASA NTRS2021

Determining Aircraft Moments of Inertia from Flight Test Data

Flight test maneuvers and dynamic modeling techniques were developed for determining aircraft moments of inertia from flight test data. Full nonlinear rigid-body rotational equations of motion were used in the analysis, with aerodynamic moment dependencies modeled by linear expansions in the aircraft states and controls. Aerodynamic parameters were estimated simultaneously with inertia parameters using equation-error modeling applied to flight test data from maneuvers designed specifically for this problem. The approach was demonstrated using a nonlinear F 16 simulation, then applied to a remotely-piloted subscale aircraft flight test. Errors in the aircraft moment of inertia parameters determined from simulated F-16 flight test data were less than 6 percent compared to the true values in the simulation. Flight test results for the subscale aircraft were within 6 percent of ground-test values obtained using the same aircraft.

Parameter estimation↗
NASA NTRS2020

Image Moment-Based Extended Object Tracking for Complex Motions

A novel image moment-based model for shape estimation and tracking of an extended target moving with a complex trajectory is presented. The proposed extended object tracking algorithm is based on multiple noisy measurement points sampled from the target at each time step. The shape of the object, approximated by an ellipse, is estimated using a combination of image moments. Dynamic models of image moments for constant velocity and coordinated turn motions are mathematically derived. An unscented Kalman filter - interacting multiple model (UKF-IMM) method is used to track the object and estimate its shape. A likelihood function based on average log-likelihood is derived for the IMM filter. Simulation results of the proposed UKF-IMM algorithm with the image momentbased models are presented that show the estimation of the shape of the object moving in a complex trajectory. The intersection over union (IoU), and the root mean square errors (RMSEs) of the position and velocity of the centroid of the ellipse are used as metrics. The comparison results of the proposed algorithm with a benchmark algorithm from literature based on the IoU and RMSE metrics are presented.

Extended object tracking↗
NASA NTRS1957

Aerodynamic Forces and Moments on a Large Ogive-Cylinder Store at Various Locations Below the Fuselage Center Line of a Swept-Wing Bomber Configuration at a Mach Number of 1.61

A supersonic wind-tunnel investigation on store interference has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.61. Forces and moments were measured on a large ogive-cylinder store in the presence of a 45 deg swept-wing-fuselage bomber configuration for a number of store locations below the fuselage center line. Results of the investigation show that large variations of store lift, drag, and pitch occur with changes in store or airplane angle of attack, store vertical location, and store horizontal location. The variation of the store forces and moments with respect to the chordwise location of the wing plan form indicates that the wing is a large factor in producing the interference loads on the store. Comparison of data for underfuselage and underwing store locations at an angle of attack of 0 deg showed maximum store drag interferences of similar magnitudes, but showed considerably smaller maximum interference on store lift an pitching moments for underfuselage store locations.

SUPERSONIC FLIGHT↗
NASA NTRS1972

Moments of inertia of the lunar globe, and their bearing on chemical differentiation of its outer layers.

It is pointed out that the observed moments of inertia of the moon, disclosed by its librations, are influenced mainly by the distribution of mass in the outer zone in which the lithostatic pressure is less than 10 kb (i.e., in the outer shell not more than 200 km deep); a conspicuous departure of such moments from those expected in hydrostatic equilibrium disclosed that these layers could never have been fluid. In the same way, the actual shape of the lunar surface cannot represent a solidified surface of a fluid, petrified at any distance from the earth. The shape of the moon and differences of its moments of inertia must reflect the way in which the initial process of cold accretion fell short of producing a globe with strictly spherically-symmetrical stratification of material. Such melting or lava flows as may have occurred at the moon's surface from time to time must have remained localized, and without much effect on the dynamical properties of the moon.

Kopal, Z.↗
NASA NTRS1974

Quadrupole moment of CO, N2, and NO/+/

Evaluation of quadrupole moments obtained for CO, N2, and NO(+) with multiconfiguration self-consistent-field wave functions chosen by the optimized valence configuration (OVC) approach of Wahl and Das (1972). The quadrupole moments thus obtained are compared with both experimental and Hartree-Fock values. The Hartree-Fock results are found to be not very accurate for N2, especially if vibrational averages over vibrational levels greater than 1 or 2 are to be taken. The agreement between the OVC quadrupole moment and the experimental values is found to be best for CO.

Billingsley, F. P., II↗
NASA NTRS1974

Results of differential elevon/aileron deflection for lateral control optimization and elevon hinge moment investigations on an 0.015-scale model (49-0) of the space shuttle orbiter in the NASA/Langley Research Center 8 foot TPT (OA116)

Aerodynamic investigations were conducted in a transonic pressure tunnel on an 0.015 scale model of the space shuttle orbiter. Major test objectives were to determine: (1) transonic differential elevon/aileron lateral control optimization; (2) transonic elevon hinge moments; (3) transonic effects of the baseline 6 inch elevon/elevon and elevon/fuselage gaps; and (4) transonic effects of the short OMS pods. Six-component aerodynamic force and moment, and elevon hinge moment data, were recorded over an angle-of-attack range form -2 to +22 degrees.

Lindsey, A. I.↗
NASA NTRS1975

Light aircraft lift, drag, and moment prediction: A review and analysis

The historical development of analytical methods for predicting the lift, drag, and pitching moment of complete light aircraft configurations in cruising flight is reviewed. Theoretical methods, based in part on techniques described in the literature and in part on original work, are developed. These methods form the basis for understanding the computer programs given to: (1) compute the lift, drag, and moment of conventional airfoils, (2) extend these two-dimensional characteristics to three dimensions for moderate-to-high aspect ratio unswept wings, (3) plot complete configurations, (4) convert the fuselage geometric data to the correct input format, (5) compute the fuselage lift and drag, (6) compute the lift and moment of symmetrical airfoils to M = 1.0 by a simplified semi-empirical procedure, and (7) compute, in closed form, the pressure distribution over a prolate spheroid at alpha = 0. Comparisons of the predictions with experiment indicate excellent lift and drag agreement for conventional airfoils and wings. Limited comparisons of body-alone drag characteristics yield reasonable agreement. Also included are discussions for interference effects and techniques for summing the results above to obtain predictions for complete configurations.

Smetana, F. O.↗
NASA NTRS1975

Differential elevon effectiveness lateral control optimization and elevon hinge moment investigation on a 0.015 scale space shuttle orbiter model 49-0 (140A/B/C modified) in the AECD VKF wind tunnel A (0A115)

Experimental aerodynamic investigations were conducted in the Arnold Engineering Development Center (AEDC) Von Karman Facility Tunnel A on a scale model of the space shuttle orbiter. The objectives of this test were: (1) determine supersonic differential elevon/aileron lateral control optimization, (2) determine supersonic elevon hinge moments, (3) determine the supersonic effects of the new baseline 6-inch elevon/elevon and elevon/fuselage gaps, and 4) determine the supersonic effects of the new short (VL70-008410) OMS pods. Six-component aerodynamic force, moment, and elevon hinge moment data were recorded.

Esparza, V.↗
NASA NTRS1974

Lunar magnetic field - Permanent and induced dipole moments

Apollo 15 subsatellite magnetic field observations have been used to measure both the permanent and the induced lunar dipole moments. Although only an upper limit of 1.3 x 10 to the 18th gauss-cubic centimeters has been determined for the permanent dipole moment in the orbital plane, there is a significant induced dipole moment which opposes the applied field, indicating the existence of a weak lunar ionosphere.

Russell, C. T.↗
NASA NTRS1974

The permanent and induced magnetic dipole moment of the moon

Magnetic field observations with the Apollo 15 subsatellite have been used to deduce the components of both the permanent and induced lunar dipole moments in the orbital plane. The present permanent lunar magnetic dipole moment in the orbital plane is less than 1.3 times ten to the eighteenth power gauss-cu cm. Any uniformly magnetized near surface layer is therefore constrained to have a thickness-magnetization product less than 2.5 emu-cm per g. The induced moment opposes the external field, implying the existence of a substantial lunar ionosphere with a permeability between 0.63 and 0.85. Combining this with recent measures of the ratio of the relative field strength at the ALSEP and Explorer 35 magnetometers indicates that the global lunar permeability relative to the plasma in the geomagnetic tail lobes is between 1.008 and 1.03.

Russell, C. T.↗
NASA NTRS1976

Effect of wing bend on the experimental force and moment characteristics of an oblique wing

Static longitudinal and lateral/directional force and moment characteristics are presented for an elliptical oblique wing mounted on top of a Sears-Haack body of revolution. The wing had an aspect ratio of 6 (based on the unswept span) and was tested at various sweep angles relative to the body axis ranging from 0 to 60 deg. In an attempt to create more symmetrical spanwise wing stalling characteristics, both wing panels were bent upward to produce washout on the trailing wing panel and washing on the leading wing panel. Small fluorescent tufts were attached to the wing surface to indicate the stall progression on the wing. The tests were conducted throughout a Mach number range from 0.6 to 1.4 at a constant unit Reynolds number of 8.2 x 10 per meter. The test results indicate that upward bending of the wing panels had only a small effect on the linearity of the moment curves and would require an impractical wing-pivot location at low lift to eliminate the rolling moment resulting from this bending.

Hopkins, E. J.↗
NASA NTRS1976

Wind-tunnel investigation of control-surface characteristics. 5: The use of a beveled trailing edge to reduce the hinge moment of a control surface

Wind tunnel tests have been made to investigate the possibility of reducing the hinge moments of a control surface by beveling the trailing edge. The tests were made with a 9 percent thick airfoil having a 30 percent chord plain flap. A faired beveled shape, 5 percent of the airfoil chord in width and having a thickness of 21/2 percent of the airfoil chord, was found to give approximately 50 percent reduction in the hinge moment caused by a given deflection of the flap and 80 percent reduction in the hinge moment due to the angle of attack of this airfoil for a wide range of angles. Elliptical trailing edge shapes were also tried but were found to be somewhat less effective.

Jones, R. T.↗