Search NASA⌕ Search

SEARCH · Search NASA

Results for “NASA Experience”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Supporting flight data analysis for Space Shuttle Orbiter Experiments at NASA Ames Research Center

The Space Shuttle Orbiter Experiments program in responsible for collecting flight data to extend the research and technology base for future aerospace vehicle design. The Infrared Imagery of Shuttle (IRIS), Catalytic Surface Effects, and Tile Gap Heating experiments sponsored by Ames Research Center are part of this program. The paper describes the software required to process the flight data which support these experiments. In addition, data analysis techniques, developed in support of the IRIS experiment, are discussed. Using the flight data base, the techniques have provided information useful in analyzing and correcting problems with the experiment, and in interpreting the IRIS image obtained during the entry of the third Shuttle mission.

Green, M. J.↗

Aerothermal modeling program. Phase 2, element B: Flow interaction experiment

NASA has instituted an extensive effort to improve the design process and data base for the hot section components of gas turbine engines. The purpose of element B is to establish a benchmark quality data set that consists of measurements of the interaction of circular jets with swirling flow. Such flows are typical of those that occur in the primary zone of modern annular combustion liners. Extensive computations of the swirling flows are to be compared with the measurements for the purpose of assessing the accuracy of current physical models used to predict such flows.

Nikjooy, M.↗

Status of the Direct Data Distribution (D(exp 3)) Experiment

NASA Glenn Research Center's Direct Data Distribution (D3) project will demonstrate an advanced, high-performance communications system that transmits information from an advanced technology payload carried by a NASA spacecraft in low Earth orbit (LEO) to a small receiving terminal on Earth. The space-based communications package will utilize a solid-state, K-band phased-array antenna that electronically steers the radiated energy beam toward a low-cost, tracking ground terminal, thereby providing agile, vibration-free, electronic steering at reduced size and weight with increased reliability. The array-based link will also demonstrate new digital processing technology that will allow the transmission of substantially increased amounts of latency-tolerant data collected from the LEO spacecraft directly to NASA field centers, principal investigators, or into the commercial terrestrial communications network. The technologies demonstrated by D3 will facilitate NASA's transition from using Government-owned communication assets to using commercial communication services. The hardware for D3 will incorporate advanced technology components developed under the High Rate Data Delivery (HRDD) Thrust Area of NASA's Office of Aerospace Technology Space Base Program at Glenn's Communications Technology Division. The flight segment components will include the electrically steerable phased-array antenna, which is being built by the Raytheon System Corporation and utilizes monolithic microwave integrated circuit (MMIC) technology operating at 19.05 GHz; and the digital encoder/modulator chipset, which uses four-channel orthogonal frequency division multiplexing (OFDM). The encoder/modulator will use a chipset developed by SICOM, Inc., which is both bandwidth and power efficient. The ground segment components will include a low-cost, open-loop tracking ground terminal incorporating a cryoreceiver to minimize terminal size without compromising receiver capability. The project is planning to hold a critical design review in the second quarter of fiscal year 2002.

Wald, Lawrence↗

First Crewed Flight: Rationale, Considerations and Challenges from the Constellation Experience

NASA's Constellation Program has made the most progress in a generation towards building an integrated human-rated spacecraft and launch vehicle. During that development, it became clear that NASA's human-rating requirements lacked the specificity necessary to defend a program plan, particularly human-rating test flight plans, from severe budget challenges. This paper addresses the progress Constellation achieved, problems encountered in clarifying and defending a human-rating certification plan, and discusses key considerations for those who find themselves in similar straits with future human-rated spacecraft and vehicles. We assert, and support with space flight data, that NASA's current human-rating requirements do not adequately address "unknown-unknowns", or the unexpected things the hardware can reveal to the designer during test.

Noriega, Carlos↗

IMPACT User Experience

NASA Human Research Project (HRP) and Exploration Medical Capabilities (ExMC) team identified a need to implement a human-centered design approach for a computational tool that performs detailed trade space analysis and research prioritization, known as Informing Mission Planning via Analysis of Complex Tradespaces (IMPACT). IMPACT processes numerous parameters such as space vehicle design, mission objectives, evacuation capability, medical events, and mission constraint, including but not limited to; duration, mass, volume, equipment, and medical capability, each with complex and interconnected relationships. The ability for users to navigate through these complexities and provide an intuitive report is critical to aiding stakeholders in the decision-making process of future missions. In this presentation we will discuss how the IMPACT team has applied human-centered design strategies to improve system usability by modelling human-system integration (i.e., task analysis) with the MagicDraw SysML modelling application and performing A/B testing of user interface prototypes.

S Ozbek↗

Analysis of Darkened Fragments Resulting from Laboratory Hypervelocity Experiments

NASA’s Orbital Debris Program Office (ODPO) relies on measurements from optical, radar, and in situ measurements to facilitate the development of data-driven orbital debris environmental engineering models such as the NASA Orbital Debris Engineering Model (ORDEM). For optical measurements, the ODPO relies on ground-based optical telescopes to statistically assess objects in geosynchronous orbit (GEO) and, in the future, low Earth orbit (LEO). The data collected include the detected object’s orbital parameters, time of observation, and optical magnitude. The latter parameter can be converted to a size using NASA’s optical Size Estimation Model (oSEM). It is well known that the observed magnitude of orbital debris can vary based on an object's material constituents, observational geometry, and the effects of space weathering.

Heather Cowardin↗

Principles of stray light suppression and conceptual application to the design of the Diffuse Infrared Background Experiment for NASA's Cosmic Background Explorer

The Diffuse Infrared Background Experiment (DIRBE) is a 10 band filter photometer that will operate at superfluid helium temperatures. Diffuse galactic and extragalactic infrared radiation in the 1-300 micrometer wavelength region will be measured by the instrument. Polarization measurements will be made for 3 bands in the 1-4 micrometer spectral region. The main sources of unwanted radiation are the sun, earth, thermal radiation from an external sun shield, the moon, the brighter planets and stars, and sky light itself from outside the instrument's nominal one degree square field of view. The system level engineering concepts and the principles of stray light suppression that resulted in the instrument design are presented.

Evans, D. C.↗

Differential Ranging Experiments with NASA’s High-Gain Deep Space Network Antennas

Radar experiments are currently under way at the Goldstone Deep Space Communications Complex (GDSCC) to determine the range of cis-lunar objects using a single high-gain 34m antenna transmitting 20 kW at X-band wavelengths, and two 34m receivers located at the GDSCC. The 34m antennas of the Deep Space Network (DSN) have effective fields-of-view of approximately 1 milli-radians, hence predetermined pointing predicts with accuracies on the order of 1 milli-degree are required. The extremely accurate 1 nano-second timing distribution of the DSN network enables sub-meter level ranging in the radial direction, by measuring delays in phase-modulated pseudonoise (PN) echoes reflected from the target. In this paper we demonstrate experimental verification of the proposed techniques by post-processing radar reflections obtained from a decommissioned geo-synchronous satellite. The characteristics of correlation-based delay measurements obtained simultaneously with two different receiving antennas are described. These are the fundamental quantities used to form the “time difference of arrival” (TDOA) observables commonly used in GPS positioning algorithms, and the results interpreted in the context of hyperbolic position location that could be used in the future to monitor spacecraft in cis-lunar space.

Cheung, Kar-Ming↗

NASA solar array flight experiment

The NASA large flexible solar array space shuttle flight experiment is described. The 32 x 4 m wing is deployed from the shuttle bay, and experiments in electrical output, multiple deployment, and structural dynamics are planned. Both 2 x 4 cm and 5.9 x 5.9 cm cell assemblies on the array blanket are evaluated. Safety/hazards provisions are described, including emergency jettison provisions. Ground testing and hardware fabrication are summarized.

Turner, G.↗

Nutrient Stability in NASA Spaceflight Experiment Rodent Food Bars

Nutrient-upgraded Rodent Food Bars are the standard diet for mice involved in spaceflight experiments aboard the International Space Station as part of NASA’s Rodent Research Project. These Food Bars are a twin-screw extruded AIN-93G based product with nutrient additives to preserve a healthy and complete diet for the animals, and the bar form factor is necessary for use in the microgravity environment. Due to the nature of NASA flight projects and the lengthy production process of these Food Bars, a shelf-life assessment was undertaken to determine nutrient stability over an extended storage time. To assess palatability and stability over an extended duration, a panel of lipid oxidation markers and both fat- and water-soluble vitamins were assessed under various time and temperature conditions via AOAC International standardized methodology. Thiamine was the least stable vitamin at room temperature. Bars that had been continually kept at 4C (t=6, 12, 27 months) showed significantly higher levels of thiamine (via Student’s t-test) compared to all other bars that underwent some degree of ambient temperature storage. This suggests that refrigeration is a key component in maintaining adequate nutrient levels in these relatively high moisture (average 29.3%) food bars. Also of note was the level of Vitamin A in the form of retinol. There was no correlation to storage temperature, but rather the only factor having an effect on retinol levels was time. As low, yet consistent decrease in retinol was observed over the course of the experiment, though at no time did the retinol levels drop below the rodent Nutrient Requirements for Laboratory Animals (NRC). In conclusion, over the 27-month time course, all analyzed vitamins and lipid oxidation factors remained relatively stable and at levels which provide fully sufficient nutrition to rodents during spaceflight. Some groups however, displayed higher-than-expected aerobic and anaerobic bacteria colony forming units, which is believed to stem from a since-revised handling technique.

Food↗

NASA's experience in the international exchange of scientific and technical information in the aerospace field

The early NASA international scientific and technical information (STI) exchange arrangements were usually detailed in correspondence with the librarians of the institutions involved. While this type of exchange, which involved only hardcopy (paper) products, grew to include some 220 organization in 43 countries, NASA's main focus shifted substantially to the STI relationship with the European Space Agency (ESA) which began in 1964. The NASA/ESA Tripartite Exchange Program, which now has more than 500 participants, provides more than 4,000 highly-relevant technical reports, fully processed, for the NASA produced 'Aerospace Database'. In turn, NASA provides an updated copy of this Database, known in Europe as the 'NASA File', for access, through ESA's Information Retrieval Service, by participating European organizations. Our experience in the evolving cooperation with ESA has established the 'model' for our more recent exchange agreements with Israel, Australia, Canada, and one under negotiation with Japan. The results of these agreements are made available to participating European organizations through the NASA File.

Thibideau, Philip A.↗

NASA's Experience with UV Remote Using SBUV and TOMS Instruments

This paper will discuss key features of the NASA algorithm that has been used to produce several highly popular geophysical products from the Solar Backscatter Ultraviolet (SBUV) and Total Ozone Mapping Spectrometer (TOMS) series of instruments. Since these instruments have a limited number of wavelengths, many innovative algorithmic approaches have been developed over the years to derive maximum information from these sensors. We will use Global Ozone Monitoring Experiment (GOME) data to test the assumptions made in these algorithms and show what additional information is contained in the GOME hyperspectral data. At NASA we are using this information to improve the SBUV and TOMS algorithms, as well as to develop more efficient algorithms to process GOME data.

Bhartia, P. K.↗

Proceedings of the Twenty-First NASA Propagation Experiments Meeting (NAPEX XXI) and the Advanced Communications Technology Satellite (ACTS) Propagation Studies Miniworkshop

The NASA Propagation Experimenters (NAPEX) meeting is convened each year to discuss studies supported by the NASA Propagation Program. Representatives from the satellite communications industry, academia and government who have an interest in space-ground radio wave propagation are invited to NAPEX meetings for discussions and exchange of information. The reports delivered at this meeting by program managers and investigators present recent activities and future plans. This forum provides an opportunity for peer discussion of work in progress, timely dissemination of propagation results, and close interaction with the satellite communications industry. NAPEX XXI took place in El Segundo, California on June 11-12, 1997 and consisted of three sessions. Session 1, entitled "ACTS Propagation Study Results & Outcome " covered the results of 20 station-years of Ka-band radio-wave propagation experiments. Session 11, 'Ka-band Propagation Studies and Models,' provided the latest developments in modeling, and analysis of experimental results about radio wave propagation phenomena for design of Ka-band satellite communications systems. Session 111, 'Propagation Research Topics,' covered a diverse range of propagation topics of interest to the space community, including overviews of handbooks and databases on radio wave propagation. The ACTS Propagation Studies miniworkshop was held on June 13, 1997 and consisted of a technical session in the morning and a plenary session in the afternoon. The morning session covered updates on the status of the ACTS Project & Propagation Program, engineering support for ACTS Propagation Terminals, and the Data Center. The plenary session made specific recommendations for the future direction of the program.

Golshan, Nasser↗

Establishing effective working relations with a potential user community - NASA Lewis Research Center experience

The NASA Lewis Research Center has held a series of six major and unique technology utilization conferences which were major milestones in planned structured efforts to establish effective working relationships with specific technology user communities. These efforts were unique in that the activities undertaken prior to the conference were extensive, and effectively laid the groundwork for productive technology transfer following, and as a direct result of, the conferences. The effort leading to the conference was in each case tailored to the characteristics of the potential user community, however, the common factors comprise a basic framework applicable to similar endeavors. The process is essentially a planned sequence of steps that constitute a technical market survey and a marketing program for the development of beneficial applications of aerospace technology beyond the aerospace field.

Foster, P.↗

ACTS 118x Final Report High-Speed TCP Interoperability Testing

With the recent explosion of the Internet and the enormous business opportunities available to communication system providers, great interest has developed in improving the efficiency of data transfer using the Transmission Control Protocol (TCP) of the Internet Protocol (IP) suite. The satellite system providers are interested in solving TCP efficiency problems associated with long delays and error-prone links. Similarly, the terrestrial community is interested in solving TCP problems over high-bandwidth links. Whereas the wireless community is interested in improving TCP performance over bandwidth constrained, error-prone links. NASA realized that solutions had already been proposed for most of the problems associated with efficient data transfer over large bandwidth-delay links (which include satellite links). The solutions are detailed in various Internet Engineering Task Force (IETF) Request for Comments (RFCs). Unfortunately, most of these solutions had not been tested at high-speed (155+ Mbps). Therefore, the NASA's ACTS experiments program initiated a series of TCP experiments to demonstrate scalability of TCP/IP and determine how far the protocol can be optimized over a 622 Mbps satellite link. These experiments were known as the 118i and 118j experiments. During the 118i and 118j experiments, NASA worked closely with SUN Microsystems and FORE Systems to improve the operating system, TCP stacks. and network interface cards and drivers. We were able to obtain instantaneous data throughput rates of greater than 520 Mbps and average throughput rates of 470 Mbps using TCP over Asynchronous Transfer Mode (ATM) over a 622 Mbps Synchronous Optical Network (SONET) OC12 link. Following the success of these experiments and the successful government/industry collaboration, a new series of experiments. the 118x experiments. were developed.

Ivancic, William D.↗

NASA-Lewis experiences with multigroup cross sections and shielding calculations

The nuclear reactor shield analysis procedures employed at NASA-Lewis are described. Emphasis is placed on the generation, use, and testing of multigroup cross section data. Although coupled neutron and gamma ray cross section sets are useful in two dimensional Sn transport calculations, much insight has been gained from examination of uncoupled calculations. These have led to experimental and analytic studies of areas deemed to be of first order importance to reactor shield calculations. A discussion is given of problems encountered in using multigroup cross sections in the resolved resonance energy range. The addition to ENDF files of calculated and/or measured neutron-energy-dependent capture gamma ray spectra for shielding calculations is questioned for the resonance region. Anomalies inherent in two dimensional Sn transport calculations which may overwhelm any cross section discrepancies are illustrated.

Lahti, G. P.↗

Nutrient Stability in NASA Spaceflight Experiment Rodent Food Bars

The nutrient-upgraded Rodent Food Bars (NuRFB) have a long history as the food of choice for NASA Space Shuttle and ISS Rodent Research missions. The NuRFB have previously been assigned an expiration date of two years after production for use in rodent flight experiments aboard the International Space Station (ISS) and three years for ground experiment use when stored between 2°-10°C. The exiguous supply of cold stowage on the ISS necessitated further investigation to determine if NuRFB can be stored at ambient temperatures (AT) without excessive nutrient degradation. The Rodent Research Project Sustaining Engineering Team at the NASA Ames Research Center in Mountain View, CA is responsible for management of this critical flight product.

Rodent Research↗