Search NASA⌕ Search

SEARCH · Search NASA

Results for “NMP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

A Reconfigurable Testbed Environment for Spacecraft Autonomy

A key goal of NASA's New Millennium Program is the development of technology for increased spacecraft on-board autonomy. Achievement of this objective requires the development of a new class of ground-based automony testbeds that can enable the low-cost and rapid design, test, and integration of the spacecraft autonomy software. This paper describes the development of an Autonomy Testbed Environment (ATBE) for the NMP Deep Space I comet/asteroid rendezvous mission.

testbed autonomy New Millennium Program (NMP) Auto↗

Microinstruments and Micro Electromechanical Systems in Support of Earth and Space Science in the New Millenium

NASA's New Millenium Program (NMP) has been chartered with flight validation of next generation technology to demonstrate the feasibility of pursuing unmanned space science with low cost, miniature spacecraft and probes. In defining a roadmap for instrument development, primary emphasis has been placed on system concepts which take best advantage of instrument miniaturization. In this paper the

New↗

Advanced Flight Computing Technologies for Validation by NASA's New Millennium Program

The New Millennium Program (NMP) consists of a series of deep-space and earth-orbiting missions that are technology-driven, in contrast to the more traditional science-driven space exploration missions of the past. These flights are designed to validate technologies that will enable a new era of low-cost highly miniaturized and highly capable spaceborne applications in the new millennium.

New↗

Pluto Express: Advanced Technologies Enable Lower Cost Missions to the Outer Solar System and Beyond

Missions to Pluto and the outer Solar System are typically driven by factors which tend to increase cost, such as: long life, high radiation exposure, a large power source, high (delta)V requirements, difficult telecommunications links, low solar illumination at the destination, and demanding science measurements. Advanced technology is a central part of responding to such challenges in a manner which permits the cost of development and operations to be an order of magnitude less than for prior outer planet missions...This paper summarizes the curent technology development plan which is tightly coupled to the New Millenium Program (NMP) Deep Space 1 technology validation flight. Specific details will be presented about advanced microelectronics technology.

New↗

The New Millenium Program: An Overview

The National Aeronautics and Space Administration (NASA)has established the New Millenium Program (NMP), a science-driven technology-validation program that is designed to accelerate the avaliability of technology needed for NASA's science missions of the 21st century.

New↗

Influence of Methylammonium Chloride on Wide-Bandgap Halide Perovskites Films for Solar Cells

Wide-bandgap perovskites are of paramount importance as the photoactive layer of the top cell in high-efficiency tandem solar cells. Comparably high Br contents are required to widen the perovskite bandgap. However, the increase in Br content causes heterogeneous halide distribution and photoinstability. Here, in this study, the positive effect of the additive methylammonium chloride (MACl) on the optical and electronic properties of Br-rich perovskite, deposited using N-methyl-2-pyrrolidone (NMP) as co-solvent and the gas quenching method, is investigated. Simultaneous in situ grazing-incidence wide-angle X-ray scattering and photoluminescence spectroscopy are used to track the evolution of the structural and optoelectronic properties of the perovskites with different amounts of Br and MACl during the spin-coating and thermal annealing steps. The formation mechanism is elucidated in the presence of MACl. It is observed that chloride ions inhibit the intermediate phases, favoring the formation of a perovskite phase with higher crystallinity. Nano X-ray fluorescence mapping recognizes Br-richer and poorer nanometric domains, whose average sizes reduce for samples with MACl. In conclusion, it is demonstrated that adding MACl affects the formation of wide-bandgap perovskites via destabilization of the intermediate phases and acts on the homogenization of the halide distribution, leading to improved solar cell performances.

14 SOLAR ENERGY↗

Effects of water-based binders on electrochemical performance of manganese dioxide cathode in mild aqueous zinc batteries

In the majority of rechargeable batteries including lithium ion batteries (LIBs), polyvinylidene fluoride (PVdF) binders are the most commonly used binder for both anode and cathode. However, using PVdF binder requires the organic solvent of N-methyl-2-pyrrolidone (NMP) which is expensive, volatile, combustible, toxic, and has poor recyclability. Therefore, switching to aqueous electrode processing routes with non-toxic binders would provide a great leap forward towards the realization of ideally fully sustainable and environmentally friendly electrochemical energy storage devices. Various water-soluble binders (aqueous binders) were characterized and compared to the performance of conventional PVDF. Our study demonstrates that the electrochemical performance of Zn/MnO2 aqueous batteries is significantly improved by using sodium carboxymethyl cellulose (CMC) binder. Additionally, CMC binders offers desirable adhesion, good wettability, homogeneous material distribution, and strong chemical stability at certain pH levels (3.5~5) without any decomposition for long-cycle life.

25 ENERGY STORAGE↗

Degradable cellulose‐based polymer brushes with controlled grafting densities

ABSTRACT Cellulose‐based polymer brushes with variable grafting densities and low dispersity were synthesized by grafting poly( n ‐butyl acrylate) (PBA) side chains from cellulose‐derived backbones via ATRP. Esterification of commercially available cellulose acetate with 2‐bromoisobutyryl bromide (2‐BiBB) in NMP provided cellulose‐based macroinitiators averaging one initiation site per double glucose unit. ATRP macroinitiators averaging up to 6 initiation sites per repeating double glucose unit were prepared by acylation of microcrystalline cellulose (MCC) in LiCl/DMAc solvent system with 2‐BiBB. A series of linear macroinitiators with narrow MWD were obtained by fractional precipitation process. The content of initiating sites was determined by elemental analysis. (Meth)acrylate side chains were then grafted from the cellulose‐based macroinitiators. The prepared cellulose‐based polymer brushes showed tunable degradation rates dependent on grafting density of the brush, following two different degradation pathways, either cleavage of the main chain or detachment of the side chains. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57 , 2426–2435

Olszewski, Mateusz↗

Revealing the Crystallization Pathways of Mixed‐Halide Low‐Dimensional Perovskites: A First Step Toward Solar Cell Applications

Ruddlesden–Popper perovskites (RPPs) are promising materials for optoelectronic devices. While iodide‐based RPPs are well‐studied, the crystallization of mixed‐halide RPPs remains less explored. Understanding the factors affecting their formation and crystallization are vital for optimizing morphology, phase purity, and orientation, which directly impact device performance. Here, we investigate the crystallization and properties of mixed‐halide RPPs (PEA) 2 FA n−1 Pb n (Br 1/3 I 2/3 ) 3n + 1 (PEA = C 6 H 5 (CH 2 ) 2 NH 3 + and FA = CH(NH 2 ) 2 + ) (n = 1, 5, 10) using DMSO ((CH 3 ) 2 SO) or NMP (OC 4 H 6 NCH 3 ) as cosolvents and MACl (MA = CH 3 NH 3 + ) as an additive. For the first time, the presence of planar defects in RPPs is directly observed by in situ grazing‐incidence wide‐angle X‐ray scattering (GIWAXS) and confirmed through the simulation of the patterns that matched the experimental. GIWAXS data also reveals that DMSO promotes higher crystallinity and vertical orientation, while MACl enhances crystal quality but increases halide segregation, shown here by nano X‐ray fluorescence (nano‐XRF) experiments. For low‐n RPPs, orientation is crucial for solar cell efficiency, but its impact decreases with increasing n. Our findings provide insights into optimizing mixed‐halide RPPs, guiding strategies to improve crystallization, phase control, and orientation for better performance not only in solar cells but also in other potential optoelectronic devices.

Guaita, Maria G D↗

Evaporation due to infrared heating and natural convection

The results obtained from a drying experiment under infrared heating are compared to those obtained from correlations for the mass transfer coefficients, which are commonly used to obtain evaporation rates for drying applications. It was shown that the mass transfer coefficients evaluated by natural convection correlations are approximately ten times lower than those measured under infrared (IR) exposure. In this work, an attempt to explain this discrepancy, which has been also observed in other studies and explained on the basis of thermal radiation effects, optical properties of NMP are presented and the implications of the IR and near infrared (NIR) spectrum on the thermal radiation effects and ensuing evaporation rates are discussed. The results show that expected raise in the film temperature, which would be due to the thermal radiation effects, cannot be used to describe the measured evaporation rates for this solvent. Therefore, this study provides important evaporation mass flux data, which cannot be predicted using traditional correlations, for the design of IR assisted drying systems used in membrane fabrication.

42 ENGINEERING↗

Anharmonic multi-phonon nonradiative transition: An ab initio calculation approach

Nonradiative carrier recombinations at deep centers in semiconductors are of great importance for both fundamental physics and device engineering. Here, we provide a revised analysis of Huang’s original nonradiative multi-phonon (NMP) theory with ab initio calculations. First, we confirmed at the first-principles level that Huang’s concise formula gives the same results as the matrix-based formula, and that Huang’s high-temperature formula provides an analytical expression for the coupling constant in Marcus theory. Secondly, we correct for anharmonic effects by taking into account local phonon-mode variations for different charge states of a defect. The corrected capture rates for defects in GaN and SiC agree well with experiments.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Chemical stability and long-term cell performance of low-cobalt, Ni-Rich cathodes prepared by aqueous processing for high-energy Li-Ion batteries

Cobalt content in Li-ion battery cathodes has become a top concern due to its price volatility and limited source availability. Low-cobalt, Ni-rich active materials are promising candidates for next-generation cathodes due to their high capacities, and water-based processing of these materials can further reduce both cost and environmental impact. We systematically evaluated the water compatibility of four different LiNi x Mn 1-x-y Co y O 2 (NMC) powders with increasing nickel contents. Comprehensive characterization verified there is no major change to their bulk structures, and only slight surface modifications related to the removal of contaminant species. For the first time, we demonstrate that LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC 811) cathodes can be formulated in water and cycled 1000 times in full pouch cells with excellent capacity retention (~70% compared to ~76% for NMP-processed cells). When implemented in future battery production lines, aqueous processing of Ni-rich NMC will simultaneously enable cost reductions and higher cell energy densities.

25 ENERGY STORAGE↗

A Prospective Study of {sup 18}FDG-PET With CT Coregistration for Radiation Treatment Planning of Lymphomas and Other Hematologic Malignancies

Purpose: This prospective single-institution study examined the impact of positron emission tomography (PET) with the use of 2-[{sup 18}F] fluoro-2-deoxyglucose and computed tomography (CT) scan radiation treatment planning (TP) on target volume definition in lymphoma. Methods and Materials: 118 patients underwent PET/CT TP during June 2007 to May 2009. Gross tumor volume (GTV) was contoured on CT-only and PET/CT studies by radiation oncologists (ROs) and nuclear medicine physicians (NMPs) for 95 patients with positive PET scans. Treatment plans and dose-volume histograms were generated for CT-only and PET/CT for 95 evaluable sites. Paired t test statistics and Pearson correlation coefficients were used for analysis. Results: 70 (74%) patients had non-Hodgkin lymphoma, 10 (11%) had Hodgkin lymphoma, 12 (10%) had plasma-cell neoplasm, and 3 (3%) had other hematologic malignancies. Forty-three (45%) presented with relapsed/refractory disease. Forty-five (47%) received no prior chemotherapy. The addition of PET increased GTV as defined by ROs in 38 patients (median, 27%; range, 5%-70%) and decreased GTV in 41 (median, 39.5%; range, 5%-80%). The addition of PET increased GTV as defined by NMPs in 27 patients (median, 26.5%; range, 5%-95%) and decreased GTV in 52 (median, 70%; range, 5%-99%). The intraobserver correlation between CT-GTV and PET-GTV was higher for ROs than for NMPs (0.94, P<.01 vs 0.89, P<.01). On the basis of Bland-Altman plots, the PET-GTVs defined by ROs were larger than those defined by NMPs. On evaluation of clinical TPs, only 4 (4%) patients had inadequate target coverage (D95 <95%) of the PET-GTV defined by NMPs. Conclusions: Significant differences between the RO and NMP volumes were identified when PET was coregistered to CT for radiation planning. Despite this, the PET-GTV defined by ROs and NMPs received acceptable prescription dose in nearly all patients. However, given the potential for a marginal miss, consultation with an experienced PET reader is highly encouraged when PET/CT volumes are delineated, particularly for questionable lesions and to assure complete and accurate target volume coverage.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Aqueous Ni-rich-cathode dispersions processed with phosphoric acid for lithium-ion batteries with ultra-thick electrodes

Lithium-ion battery (LIB) production can benefit both economically and environmentally from aqueous processing. Although these electrodes have the potential to surpass electrodes conventionally processed with N -methyl-2-pyrrolidone (NMP) in terms of performance, significant issues still exist with respect to ultra-thick cathodes ($\gg$4 mAh/cm 2 areal capacities). A major concern for these types of electrodes with high-nickel active material stems from lithium leaching from active material, which drives the pH of the dispersion in excess of 12 and subsequently corrodes the current collector interface. As this corrosion reaction proceeds, hydrogen generation at the interface creates bubbles which cause severe cracking in the dried electrode surface. When areal loadings are increased, this effect becomes more pronounced and is detrimental to both mechanical and electrochemical properties of these electrodes. In this work, a technique for mitigating corrosion at the current collector by adjusting the pH of the dispersion with the addition of phosphoric acid is investigated. Phosphoric acid was added in 0.5 wt% increments between 0.0 and 1.5 wt%, and effects on rheology, adhesion, corrosion, and electrochemical performance were investigated. A technique is reported for producing aqueous processed cathodes with areal loadings of 6–8 mAh/cm 2 with reduced surface cracking and superior high-rate discharge capacity (i.e. high-power performance) for this class of cathode loadings.

25 ENERGY STORAGE↗