Search NASA⌕ Search

SEARCH · Search NASA

Results for “National Transonic Facility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Enhancements to the FAST-MAC Circulation Control Model and Recent High-Reynolds Number Testing in the National Transonic Facility

A second wind tunnel test of the FAST-MAC circulation control model was recently completed in the National Transonic Facility at the NASA Langley Research Center. The model was equipped with four onboard flow control valves allowing independent control of the circulation control plenums, which were directed over a 15% chord simple-hinged flap. The model was configured for low-speed high-lift testing with flap deflections of 30 and 60 degrees, along with the transonic cruise configuration with zero degree flap deflection. Testing was again conducted over a wide range of Mach numbers up to 0.88, and Reynolds numbers up to 30 million based on the mean chord. The first wind tunnel test had poor transonic force and moment data repeatability at mild cryogenic conditions due to inadequate thermal conditioning of the balance. The second test demonstrated that an improvement to the balance heating system significantly improved the transonic data repeatability, but also indicated further improvements are still needed. The low-speed highlift performance of the model was improved by testing various blowing slot heights, and the circulation control was again demonstrated to be effective in re-attaching the flow over the wing at off-design transonic conditions. A new tailored spanwise blowing technique was also demonstrated to be effective at transonic conditions with the benefit of reduced mass flow requirements.

Milholen, William E., II↗
NASA NTRS1989

Longitudinal aerodynamic characteristics of a subsonic, energy-efficient transport configuration in the National Transonic Facility

The Reynolds number, aeroelasticity, boundary layer transition, and nonadiabatic wall temperature effects, and data repeatability was determined in the National Transonic Facility (NTF) for a subsonic, energy efficient transport model. The model was tested over a Mach number range of 0.50 to 0.86 and a Reynolds number range of 1.9 million to approximately 23.0 million (based on mean geometric chord). The majority of the data was taken using cryogenic nitrogen (data at 1.9 million Reynolds number was taken in air). Force and moment, wing pressure, and wing thermocouple data are presented. The data indicate that increasing Reynolds number resulted in greater effective camber of the supercritical wing and horizontal tail, resulting in greater lift and pitching moment coefficients at nearly all angles of attack for M = 0.82. As Reynolds number was increased, untrimmed L/D increased, the angle of attack for maximum L/D decreased, drag creep was reduced significantly, and drag divergence Mach number increased slightly. Data repeatability for both modes of operation of the NTF (air and cryogenic nitrogen) was generally very good, and nonadiabatic wall effects were estimated to be small. Transition-free and transition-fixed configurations had significantly different force and moment data at M = 0.82 for low Reynolds number, and very small differences were noted at high Reynolds numbers.

Jacobs, Peter F.↗
NASA NTRS1996

Finite Element Analysis of a NASA National Transonic Facility Wind Tunnel Balance

This paper presents the results of finite element analyses and correlation studies performed on a NASA National Transonic Facility (NTF) Wind Tunnel balance. In the past NASA has relied primarily on classical hand analyses, coupled with relatively large safety factors, for predicting maximum stresses in wind tunnel balances. Now, with the significant advancements in computer technology and sophistication of general purpose analysis codes, it is more reasonable to pursue finite element analyses of these balances. The correlation studies of the present analyses show very good agreement between the analyses and data measured with strain gages and therefore the studies give higher confidence for using finite element analyses to analyze and optimize balance designs in the future.

Lindell, Michael C.↗
NASA NTRS1999

Finite Element Analysis of a NASA National Transonic Facility Wide Tunnel Balance

This paper presents the results of finite element analyses and correlation studies performed on a NASA National Transonic Facility (NTF) Wind Tunnel balance. In the past NASA has relied primarily on classical hand analyses, coupled with relatively large safety factors, for predicting maximum stresses in wind tunnel balances. Now, with the significant advancements in computer technology and sophistication of general purpose analysis codes, it is more reasonable to pursue finite element analyses of these balances. The correlation studies of the present analyses show very good agreement between the analyses and data measured with strain gages and therefore the studies give higher confidence for using finite element analyses to analyze and optimize balance designs in the future.

Lindell, Michael C.↗
NASA NTRS2006

Skin Friction at Very High Reynolds Numbers in the National Transonic Facility

Skin friction coefficients were derived from measurements using standard measurement technologies on an axisymmetric cylinder in the NASA Langley National Transonic Facility (NTF) at Mach numbers from 0.2 to 0.85. The pressure gradient was nominally zero, the wall temperature was nominally adiabatic, and the ratio of boundary layer thickness to model diameter within the measurement region was 0.10 to 0.14, varying with distance along the model. Reynolds numbers based on momentum thicknesses ranged from 37,000 to 605,000. The measurements approximately doubled the range of available data for flat plate skin friction coefficients. Three different techniques were used to measure surface shear. The maximum error of Preston tube measurements was estimated to be 2.5 percent, while that of Clauser derived measurements was estimated to be approximately 5 percent. Direct measurements by skin friction balance proved to be subject to large errors and were not considered reliable.

Watson, Ralph D.↗
NASA NTRS2009

Experimental Investigation of the Flow about a 65 deg Delta Wing in the NASA Langley National Transonic Facility

An experimental investigation for the flow about a 65 deg. delta wing has been conducted in the NASA Langley National Transonic Facility (NTF). The tests were conducted at Reynolds numbers, based on the mean aerodynamic chord, ranging from 6 million to 120 million and at Mach numbers ranging from 0.4 to 0.9. The model incorporated four different leading-edge bluntness values. The data include detailed static surfacepressure distributions as well as normal-force and pitching-moment coefficients. The test program was designed to quantify the effects of Mach number, Reynolds number, and leading-edge bluntness on the onset and progression of leading-edge vortex separation.

Luckring, James M.↗
NASA NTRS1984

Design study of test models of maneuvering aircraft configurations for the National Transonic Facility (NTF)

The feasibility of designing advanced technology, highly maneuverable, fighter aircraft models to achieve full scale Reynolds number in the National Transonic Facility (NTF) is examined. Each of the selected configurations are tested for aeroelastic effects through the use of force and pressure data. A review of materials and material processes is also included.

Griffin, S. A.↗
NASA NTRSDate not supplied

It’s Hip To Be Square - Refurbishment of the NASA Langley National Transonic Facility Test Section Plenum Door

The “nearside” plenum door (NPD) at the 39-year-old NASA Langley Research Center (LARC) National Transonic Facility (NTF) has become increasingly recalcitrant during the opening /closing sequence. The NPD is the primary means of entry into the test section for personnel and for model installation. The sliding NPD hardware guide bearings have failed three (3) times within a one-year period and “quick fixes” were able to be made to guide rails, wheels and bearings to put the NPD back into operation. The NPD no longer can utilize a “quick fix” as the rolling hardware is at its limit for further modifications. This presentation will describe the NPD situation, the findings as to the cause of the periodic NPD failures, and the solution to remove, refurbish, and reinstall the NPD.

Test Facilities↗
NASA NTRSDate not supplied

Application of PSP on the SWiFT Model in the National Transonic Facility

This report details the results from a Pressure Sensitive Paint test on a blended/hybrid wing body model conducted at the National Transonic Facility. This test investigated potential instabilities that can occur at high Reynolds number and low Mach number testing conditions. The upper surface of the model was coated with pressure sensitive paint, and data was collected at various Mach numbers and angles of attack. For this test, typical pitch-pause testing was completed as well as a novel continuous sweep functionality that provided much greater angle of attack resolution. Results from this test will be presented, including indications of potential instability points in the testing envelope.

NTF↗
NASA NTRS2008

Experimental Investigation of the DLR-F6 Transport Configuration in the National Transonic Facility

An experimental aerodynamic investigation of the DLR (German Aerospace Center) F6 generic transport configuration has been conducted in the NASA NTF (National Transonic Facility) for CFD validation within the framework of the AIAA Drag Prediction Workshop. Force and moment, surface pressure, model deformation, and surface flow visualization data have been obtained at Reynolds numbers of both 3 million and 5 million. Flow-through nacelles and a side-of-body fairing were also investigated on this wing-body configuration. Reynolds number effects on trailing edge separation have been assessed, and the effectiveness of the side-of-body fairing in eliminating a known region of separated flow has been determined. Data obtained at a Reynolds number of 3 million are presented together for comparison with data from a previous wind tunnel investigation in the ONERA S2MA facility. New surface flow visualization capabilities have also been successfully explored and demonstrated in the NTF for the high pressure and moderately low temperature conditions required in this investigation. Images detailing wing surface flow characteristics are presented.

Gatlin, Gregory M.↗
NASA NTRS2014

Thrust Removal Scheme for the FAST-MAC Circulation Control Model Tested in the National Transonic Facility

A second wind tunnel test of the FAST-MAC circulation control semi-span model was recently completed in the National Transonic Facility at the NASA Langley Research Center. The model allowed independent control of four circulation control plenums producing a high momentum jet from a blowing slot near the wing trailing edge that was directed over a 15% chord simple-hinged flap. The model was configured for transonic testing of the cruise configuration with 0deg flap deflection to determine the potential for drag reduction with the circulation control blowing. Encouraging results from analysis of wing surface pressures suggested that the circulation control blowing was effective in reducing the transonic drag on the configuration, however this could not be quantified until the thrust generated by the blowing slot was correctly removed from the force and moment balance data. This paper will present the thrust removal methodology used for the FAST-MAC circulation control model and describe the experimental measurements and techniques used to develop the methodology. A discussion on the impact to the force and moment data as a result of removing the thrust from the blowing slot will also be presented for the cruise configuration, where at some Mach and Reynolds number conditions, the thrust-removed corrected data showed that a drag reduction was realized as a consequence of the blowing.

Chan, David T.↗
NASA NTRS2019

Experimental Investigation of the NASA Common Research Model with a Natural Laminar Flow Wing in the NASA Langley National Transonic Facility

A test of the new NASA Common Research Model with a Natural Laminar Flow (CRMNLF) semispan wing in the NASA Langley National Transonic Facility (NTF) was completed in October 2018. The main focus of this test was the evaluation of the extent of laminar flow on the CRM-NLF wing at various Reynolds numbers and test conditions. During this test, data were acquired at chord Reynolds numbers from 10 to 30 million and at Mach numbers ranging from 0.84 to 0.86. This investigation provided valuable insight into the necessary procedures for laminar flow testing in the NTF. It also significantly advanced the new carbonbased heating layer technique to improve the quality of transition visualization data from temperature sensitive paint (TSP) in a cryogenic wind tunnel.

Rivers, Melissa B.↗
NASA NTRS1981

An application of multivariable design techniques to the control of the national transonic facility

The digital versions of optimal linear regulator theory and eigenvalue placement theory are applied to the Mach number control loop of the National Transonic Facility cryogenic wind tunnel. The control laws developed are evaluated on a nonlinear simulation of the tunnel process for a typical est condition and are found to significantly reduce the open loop time required to achieve a Mach number set point.

Armstrong, E. S.↗
NASA NTRS2006

Recent Improvements in Semi-Span Testing at the National Transonic Facility (Invited)

Three wind tunnel investigations of a commercial transport, high-lift, semi-span configuration have recently been conducted in the National Transonic Facility at the NASA Langley Research Center. Throughout the course of these investigations multiple improvements have been developed in the facility semi-span test capability. The primary purpose of the investigations was to assess Reynolds number scale effects on a modern commercial transport configuration up to full-scale flight test conditions (Reynolds numbers on the order of 27 million). The tests included longitudinal aerodynamic studies at subsonic takeoff and landing conditions across a range of Reynolds numbers from that available in conventional wind tunnels up to flight conditions. The purpose of this paper is to discuss lessons learned and improvements incorporated into the semi-span testing process. Topics addressed include enhanced thermal stabilization and moisture reduction procedures, assessments and improvements in model sealing techniques, compensation of model reference dimensions due to test temperature, significantly improved semi-span model access capability, and assessments of data repeatability.

Gatlin, Gregory M.↗
NASA NTRS2006

Recent Improvements in Semi-Span Testing at the National Transonic Facility (Invited)

Three wind tunnel investigations of a commercial transport, high-lift, semi-span configuration have recently been conducted in the National Transonic Facility at the NASA Langley Research Center. Throughout the course of these investigations multiple improvements have been developed in the facility semi-span test capability. The primary purpose of the investigations was to assess Reynolds number scale effects on a modern commercial transport configuration up to full-scale flight test conditions (Reynolds numbers on the order of 27 million). The tests included longitudinal aerodynamic studies at subsonic takeoff and landing conditions across a range of Reynolds numbers from that available in conventional wind tunnels up to flight conditions. The purpose of this paper is to discuss lessons learned and improvements incorporated into the semi-span testing process. Topics addressed include enhanced thermal stabilization and moisture reduction procedures, assessments and improvements in model sealing techniques, compensation of model reference dimensions due to test temperature, significantly improved semi-span model access capability, and assessments of data repeatability.

Gatlin, G. M.↗
NASA NTRS2011

Flight Reynolds Number Testing of the Orion Launch Abort Vehicle in the NASA Langley National Transonic Facility

A 6%-scale unpowered model of the Orion Launch Abort Vehicle (LAV) ALAS-11-rev3c configuration was tested in the NASA Langley National Transonic Facility to obtain static aerodynamic data at flight Reynolds numbers. Subsonic and transonic data were obtained for Mach numbers between 0.3 and 0.95 for angles of attack from -4 to +22 degrees and angles of sideslip from -10 to +10 degrees. Data were also obtained at various intermediate Reynolds numbers between 2.5 million and 45 million depending on Mach number in order to examine the effects of Reynolds number on the vehicle. Force and moment data were obtained using a 6-component strain gauge balance that operated both at warm temperatures (+120 . F) and cryogenic temperatures (-250 . F). Surface pressure data were obtained with electronically scanned pressure units housed in heated enclosures designed to survive cryogenic temperatures. Data obtained during the 3-week test entry were used to support development of the LAV aerodynamic database and to support computational fluid dynamics code validation. Furthermore, one of the outcomes of the test was the reduction of database uncertainty on axial force coefficient for the static unpowered LAV. This was accomplished as a result of good data repeatability throughout the test and because of decreased uncertainty on scaling wind tunnel data to flight.

Chan, David T.↗
NASA NTRSDate not supplied

Experimental Investigation of a Boundary Layer Ingesting Tailcone Thruster Configuration at the National Transonic Facility

A transonic, high Reynolds number wind tunnel test of a Boundary Layer Ingesting Tailcone System (BLITS) was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center during the spring of 2023. The test was sponsored by the NASA Advanced Air Transport Technology Project and produced a large dataset to help in the development and validation of an integrated airframe-turbomachinery computational simulation capability. The Common Research Model with Tail Cone Thruster (CRM-TCT) configuration was tested at Mach numbers from 0.75 to 0.85 and Reynolds number based on mean aerodynamic chord from 5 to 15 million, with the objective of characterizing the tailcone nacelle inlet pressure and flow angle profile, characterizing the aftbody boundary layer (BL), and evaluating the overall airframe configuration performance. The test article included multiple tailcone nacelle assemblies with different measurement objectives, and each assembly was able to be controlled remotely and rotate in small increments, allowing for an increased measurement density for characterizing the nacelle inlet distortion. Additionally, the use of cryogenic-rated miniature BL rakes was successful in measuring boundary layer heights on the aftbody. Sensitivities of the measured quantities of interest to Mach number, Reynolds number, angle of attack, and nacelle weight flow rate are also presented.

boundary layer ingestion (BLI)↗
NASA NTRSDate not supplied

Experimental Investigation of a Boundary Layer Ingesting Tailcone Thruster Configuration at the National Transonic Facility

A transonic, high Reynolds number wind tunnel test of a Boundary Layer Ingesting Tailcone System (BLITS) was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center during the spring of 2023. The test was sponsored by the NASA Advanced Air Transport Technology Project and produced a large dataset to help in the development and validation of an integrated airframe-turbomachinery computational simulation capability. The Common Research Model with Tail Cone Thruster (CRM-TCT) configuration was tested at Mach numbers from 0.75 to 0.85 and Reynolds number based on mean aerodynamic chord from 5 to 15 million, with the objective of characterizing the tailcone nacelle inlet pressure and flow angle profile, characterizing the aftbody boundary layer (BL), and evaluating the overall airframe configuration performance. The test article included multiple tailcone nacelle assemblies with different measurement objectives, and each assembly was able to be controlled remotely and rotate in small increments, allowing for an increased measurement density for characterizing the nacelle inlet distortion. Additionally, the use of cryogenic-rated miniature BL rakes was successful in measuring boundary layer heights on the aftbody. Sensitivities of the measured quantities of interest to Mach number, Reynolds number, angle of attack, and nacelle weight flow rate are also presented.

boundary layer ingestion (BLI)↗