Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ozone profile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Equatorial ozone profiles from the ground to 52 km during the Southern Hemisphere autumn

The results of an ozone measurement campaign conducted at Natal, Brazil from March 25 to April 15, 1985 are reported. Complete profiles of ozone, pressure, and temperature were obtained from the ground to 52 km, and all of the profiles correspond with site overpasses by ozone instruments on NASA and NOAA satellites. The profiles from this measurement series show reasonable agreement with established satellite climatologies. Stratospheric ozone variability was 2 percent or less during the 3 weeks of the measurement campaign, with stratospheric temperature and pressure variabilities half that amount. Low variability at a single location for this period implies comparable uniformity for ozone profiles over a large area around the measurement site. The auxiliary pressure and temperature profiles presented here allow the use of this data set as a transfer standard between satellite instruments with different fundamental ozone measurements. Finally, the low ozone variability in the stratosphere at Natal during this measurement series should provide an opportunity for high-quality intercomparisons of measured and modeled ozone concentrations in the equatorial stratosphere and lower mesosphere as well as a consistency check among satellite ozone measurements.

Barnes, Robert A.↗

Homogenized Ground-Based and Profile Ozone Datasets From the TOAR-II/HEGIFTOM Project: Methods and Station Trends

Within the framework of the second phase of the Tropospheric Ozone Assessment Report (TOAR-II), it was recognized that an essential first step for deriving accurate trends from the ground-based networks that monitor ozone in the free troposphere is putting the measurements on the same basis with respect to absolute references and processing methods. The relevant procedures are referred to as “harmonization” or “homogenization”. The TOAR II working group, “HEGIFTOM” (Harmonization and Evaluation of Ground-based Instruments for Free-Tropospheric Ozone Measurements), has carried out harmonization for five types of network (Figure below) instruments (mid-1990s to 2020): ozonesondes, commercial aircraft IAGOS landing/takeoff profiles, Fourier-Transform Infrared spectrometer (FTIR), tropospheric Lidar, and Brewer/Dobson Umkehr. First, we summarize the homogenization effort for each network that provides new quality-assessed ozone profile or segment (partial column) data sets, including uncertainty estimates and quality flags. Second, with the HEGIFTOM datasets forming the basis for a global assessment of tropospheric ozone column trends, results derived with various trend detection algorithms will be presented. The ultimate goal is evaluation of the consistency of the calculated trends among different techniques at selected stations and/or regions.

ozone↗

Comparison of stratospheric ozone profiles and their seasonal variations as measured by lidar and Stratospheric Aerosol and Gas Experiment during 1988

A ground-based, high power, laser remote sensing system for measurements of stratospheric ozone concentration profiles has been in operation at the Jet Propulsion Laboratory Table Mountain Facility located in southern California, since January 1988. The seasonal variations observed in the ozone profiles, during 1988 and as a function of altitude, are described here. These profiles are compared with those from the Stratospheric Aerosol and Gas Experiment satellite instrument made within a radius of 1000 km from the lidar and also with the zonal mean measurements made in the band 34.4 +/- 5 deg. Comparison with the proposed new CIRA ozone reference model has also been carried out. The seasonal variations, between 25 and 50 km, observed by the two instruments and indicated by the reference model are in good agreement.

Mcdermid, I. Stuart↗

The Effects of a 1998 Observing System Change on MERRA-2-Based Ozone Profile Simulations

Model simulations of ozone (O3) driven by meteorological reanalyses are useful for filling observational gaps and interpreting observed O3 variability and trends. However, the transport circulation of reanalysis products is impacted by changes to the observing system (the data assimilated into the reanalyses). We examine the impacts of these changes on simulated O3 from two models, Global Modeling Initiative (GMI) Chemistry Transport Model (GMI CTM) and Modern‐Era Retrospective Analysis for Research Applications version 2 (MERRA‐2) GMI Replay (M2 GMI Replay) simulation, using observations from global ozonesondes (>50,000 profiles) and satellites from 1980 to 2016. Both models are constrained by meteorology from the NASA MERRA‐2 reanalysis, and both use versions of NASA's GMI chemical mechanism. We focus on an observing system change affecting simulated O3 after 1998, associated with the assimilation of temperature and humidity data from new microwave profiling satellites. A large post‐1998 O3 increase, mainly confined to 15–20‐km altitude, of ~10 Dobson units (DU) in midlatitudes occurs in the GMI CTM, worsening the bias compared to observations. In contrast, an increase in M2 GMI Replay simulation O3 of ~10 DU is observed only near −60° latitude, reducing the bias compared to observations. The GMI CTM O3 high biases display a Quasi‐Biennial Oscillation (QBO)‐like periodicity that result from excessive transport from the tropical stratosphere to the midlatitude lower stratosphere during the QBO westerly phase. We quantify O3 discontinuities caused by MERRA‐2 observing system changes and demonstrate how the MERRA‐2 Global Modeling Initiative Replay simulation dampens the effects of these changes and QBO‐driven artifacts on simulated lower stratospheric and total O3. We caution against using simulations driven by a reanalysis to derive multidecadal O3 trends, especially prior to 1998.

Replay↗

Effect of stratospheric aerosol on ozone profile from BUV measurements

Results of a simulation study on the effects of optically thick stratospheric sulfate aerosol layers on the backscattered ultraviolet radiation (buv) in the range 256-340 nm are presented. In general, the increased Mie scattering produced by the aerosols results in an enhancement of the buv radiation. The increase is approximately linear with optical depth and strongly depends on solar zenith angle and aerosol layer altitude in relation to the ozone maximum. The effect is greatest at those wavelenghts whose contribution functions peak in the vicinity of the densest part of the aerosol layer. The aerosol induced perturbation of the buv field affects the ozone profile retrieval from space measurements by the Solar Backscatter Ultraviolet Experiment (SBUV) experiment. In the tropical stratosphere, the retrieved ozone between 25 and 45 km is underestimated as a result of increased Mie scattering. On the other hand, an algorithm related effect causes the retrieved ozone below 25 km to be overestimated by an amount similar to the stratospheric deficit.

Torres, Omar↗

First ozone profiles measured with electrochemical and chemiluminescent sondes, developed in Russia

Results obtained with experimental balloon electrochemical and chemiluminescent ozonesondes are summarized and estimated as quite satisfactory. The average normalization factor for the electrochemical ozonesonde obtained in 1991 at four Soviet balloon routine network stations is 1.069+.073 (in 17 flights). Some ozone profiles obtained in summer 1991 at Volgograd are discussed together with corresponding meteorological data.

Zuyaguintsev, Anatoly M.↗

Methods for Validation of Random Uncertainty Estimates and Their Applications to Ozone Profiles From Limb-Viewing Satellite Instruments

For satellite measurements of atmospheric composition, the random uncertainty estimates provided by retrieval algorithms might be imperfect due to various approximations used in the retrievals or the presence of unknown error sources. This paper presents an overview of the methods used for the validation of random uncertainty estimates. All methods discussed in this study are categorized, and assumptions and limitations of each method are discussed. This overview evaluates these methods in application to ozone profile measurements from limb and occultation satellite instruments and provides practical illustrations of random uncertainty validation.

Viktoria F Sofieva↗

Atmospheric ozone profiles from high resolution UV spectra obtained with a balloon-borne spectrometer

High resolution solar spectra at high and low sun angles are analyzed by a layer-by-layer three-wavelength differential absorption method. Ozone amounts are derived from the ratio of a low sun angle scan through a long atmosphere path to a high sun angle scan through a negligible atmosphere path. Ozone volume-mixing ratio profiles are derived and agree with standard profiles. The accuracy of the ozone profiles is found to be limited mostly by the accuracy of the ozone absorption coefficients, and suggestions are made for improving the accuracy of the results in future measurements.

Gillis, J. R.↗

Reduced Dimensionality Analysis of TEMPO Ozone Profile Retrievals Using the Compact Phase Space (CPSR) Algorithm

TEMPO ozone (O 3 ) profile retrievals are expected to have fidelity in the troposphere due the sensitivities of the associated averaging kernels. However, those averaging kernels are severely rank deficiency meaning that a visual inspection of the vertical structure of the averaging kernel profile sensitivities is misleading due linear dependencies in the profile. The Compact Phase Space Retrieval (CPSR) algorithm use singular value decompositions of the averaging kernels and the ‘compressed’ retrieval solution error covariance to project the transformed averaging kernels into a space that removes the linear dependencies and accounts for the solution error uncertainties. In this oral presentation and poster, we apply the CPSR dimensional reduction analysis to TEMPO and TROPOMI O 3 profile retrievals for 13:45 UTC March 29, 2024 to study the phase space characteristics of the transformed averaging kernels as a function of latitude for North America. Our results show that TEMPO generally has more phase space vertical structure in the troposphere than TROPOMI. TEMPO has four to five dominant modes, and TROPOMI has five to six dominant modes. That means that dimensional reduction can reduce the TEMPO resource requirements by ~77% and the TROPOMI requirements by ~81%. Finally, we found that after removing linear dependences and after accounting for solution uncertainties TEMPO still has sensitivities throughout the troposphere.

TEMPO↗

Trends in ozone profile measurements

From an examination of the agreements and differences between different satellite instruments, it is difficult to believe that existing satellite instruments determine upper stratospheric ozone much better than 4 pct.; by extension, it probably would require at least a 4 pct. change to be reliably detected as a change. The best estimates of the vertical profiles of ozone change in the upper stratosphere between 1979 and 1986 are judged to be those given by the two SAGE satellite instruments. SAGE-2 minus SAGE-1 gives a much lower ozone reduction than that given by the archived Solar Backscatter UV data. The average SAGE profiles of ozone changes between 20 and 50 degs north and between 20 and 50 degs south are given. The SAGE-1 and SAGE-2 comparison gives an ozone reduction of about 4 pct. at 25 km over temperate latitudes. Five ground based Umkehr stations between 36 and 52 degs north, corrected for the effects of volcanic aerosols, report an ozone reduction between 1979 and 1987 at Umkehr layer 8 of 9 + or - 5 pct. The central estimate of upper stratospheric ozone reduction given by SAGE at 40 km is less than the central value estimated by the Umkehr method at layer 8.

Johnston, H.↗

Assimilation of ozone profiles from the Improved Limb Atmospheric Spectrometer: Study on Antarctic Ozone - 2

Ozone data from the Improved Limb Atmospheric Spectrometer-II (ILAS-II) were included in addition to other satellite observations in the ozone assimilation system at the Global Modeling and Assimilation Office (GMAO) of NASA/Goddard. The control run assimilated data from NOAA 16 Solar Backscatter Ultraviolet/2 (SBUV/2) and Polar Ozone and Aerosol Measurement III (POAM III) instruments. Persistent impacts over Antarctica and transient impacts over northern middle and high latitudes are seen from April to October 2003, when ILAS-II provided good coverage. The largest improvements with respect to independent ozone sonde data are seen over the South Pole station. Ozone analyses and forecasts from the assimilation of SBUV/2, POAM III and ILAS-II data b e used to investigate the transport of ozone to southern middle latitudes following the breakup of the Antarctic vortex. The quality of analyses and forecasts is evaluated by comparison with independent Stratospheric Aerosol and Gas Experiment III (SAGE III) ozone data near 46degs. Anomaly correlations between SAGE III data and forecasts'exceed 0.6 for up to five to seven days at 30,50, and 70 ma. The loss of skill with advancing forecast length is related to dynamical errors due to an excessively persistent vortex in longer forecasts, which hampers the transport of low ozone air into middle latitudes.

Stajner, Ivanka↗

Evaluating a Priori Ozone Profile Information Used in TEMPO (Tropospheric Emissions: Monitoring of Pollution) Tropospheric Ozone Retrievals

A primary objective for TOLNet is the evaluation and validation of space-based tropospheric O3 retrievals from future systems such as the Tropospheric Emissions: Monitoring of Pollution (TEMPO) satellite. This study is designed to evaluate the tropopause-based O3 climatology (TB-Clim) dataset which will be used as the a priori profile information in TEMPO O3 retrievals. This study also evaluates model simulated O3 profiles, which could potentially serve as a priori O3 profile information in TEMPO retrievals, from near-real-time (NRT) data assimilation model products (NASA Global Modeling and Assimilation Office (GMAO) Goddard Earth Observing System (GEOS-5) Forward Processing (FP) and Modern-Era Retrospective analysis for Research and Applications version 2 (MERRA2)) and full chemical transport model (CTM), GEOS-Chem, simulations. The TB-Clim dataset and model products are evaluated with surface (0-2 km) and tropospheric (0-10 km) TOLNet observations to demonstrate the accuracy of the suggested a priori dataset and information which could potentially be used in TEMPO O3 algorithms. This study also presents the impact of individual a priori profile sources on the accuracy of theoretical TEMPO O3 retrievals in the troposphere and at the surface. Preliminary results indicate that while the TB-Clim climatological dataset can replicate seasonally-averaged tropospheric O3 profiles observed by TOLNet, model-simulated profiles from a full CTM (GEOS-Chem is used as a proxy for CTM O3 predictions) resulted in more accurate tropospheric and surface-level O3 retrievals from TEMPO when compared to hourly (diurnal cycle evaluation) and daily-averaged (daily variability evaluation) TOLNet observations. Furthermore, it was determined that when large daily-averaged surface O3 mixing ratios are observed (65 ppb), which are important for air quality purposes, TEMPO retrieval values at the surface display higher correlations and less bias when applying CTM a priori profile information compared to all other data products. The primary reason for this is that CTM predictions better capture the spatio-temporal variability of the vertical profiles of observed tropospheric O3 compared to the TB-Clim dataset and other NRT data assimilation models evaluated during this study.

Pollution↗

Tethered Balloon System Ozone Profiles during CoURAGE Summer Intensive Operational Period Field Campaign Report

During the summer IOP, the small ARM field campaign CRGTBSO3 collected measurements to gain an improved understanding of differences between the atmospheric composition in and just above the marine layer at the CoURAGE TBS site near the eastern shore of Chesapeake Bay. CRGTBSO3 included guest instrumentation with ozone (O 3 ) profile measurements on the TBS and surface O3 and meteorological measurements at the TBS site. An En-Sci 2Z electrochemical cell (ECC) ozonesonde (Komhyr 1969, 1986, Witte et al. 2018) was included on the TBS. The ozonesonde was connected to an InterMet iMet-4RSB radiosonde, and the overall data collected included vertical profiles of ozone, relative humidity, temperature, pressure, and altitude. The CRGTBSO3 iMet-4 radiosonde data is identical to that of the iMet in the Tethered Balloon System Merged Data Product (TBSMERGED; Gaustad and Dexheimer 2025). The TBSMERGED data product also includes meteorological data from a different sensor, the iMet XQ2. In some cases, the iMet XQ2 relative humidity (RH) data may be more accurate than the iMet-4, such as for some instances when the iMet-4 RH data stays at 100% for an extended period throughout a profile.

54 ENVIRONMENTAL SCIENCES↗

An improved rocket ozonesonde (ROCOZ-A). II - Preparation of stratospheric ozone profiles

The ROCOZ-A radiometer measures ozone by long pathlength photometry in the stratosphere and lower mesosphere. After a rocket launch to an apogee of 70 km, the instrument measures the solar ultraviolet irradiance over its four filter wavelengths as it descends on a parachute. The fundamental values from ROCOZ-A are ozone overburdens versus radar altitude from 53 to 20 km. The slope of these values gives ozone number density. At one standard deviation the repeatability of the ozone overburden measurements averages 2.4 percent. For ozone number density the repeatability averages 3.2 percent with a significant increase at altitudes below the ozone number density maximum. The accuracy limits for overburden and number density are estimated at 5-7 percent. With auxiliary measurements of pressure and temperature, ozone results are also produced in terms of ozone mixing ratio, albeit with a slight broadening of the estimated accuracy limits. The vertical response of ROCOZ-A ozone measurements (full width at half maximum) is 4 km. The assembly of ROCOZ-A profiles can be used to compare with measurements from each of the current NASA and NOAA satellite ozone instruments. In addition, the repeatability of ROCOZ-A allows the use of this instrument as a transfer standard between satellite instruments with different fundamental ozone measurements.

Barnes, Robert A.↗

Ozone profile measurements of McMurdo Station, Antarctica, during the spring of 1987

Ozone and temperature profiles were measured in 50 balloon flights at McMurdo Station (78 deg S) during the spring of 1987. Compared to similar data obtained in 1986, stratospheric temperatures were lower and the spring time Antarctic ozone reduction was greater in magnitude, extended to higher altitude, and proceeded at a higher rate in 1987. Ozone partial pressures reached values as low as 3 nbar (as compared to about 10 nbar in 1986) in the 16- to 18-km region in early and late October, down from about 150 nbar in late August. These low values suggest essentially complete removal of ozone in this region. The upper boundary of the depletion region was observed to be 2-3 km higher than in 1986, extending to altitudes as high as 24 km in mid-September. When averaged over September, the ozone mixing ratio at 18 km decayed with a half-life of only 12.4 days, as compared to about 28 days in 1986. Adiabatic vertical motions over 1- to 2-km intervals between 12 and 20 km with consequent ozone reductions were observed in association with the formation of nacreous clouds, indicating these to be rare events on a local scale probably associated with mountain lee waves.

Hofmann, D. J.↗

Ozone profile intercomparison based on simultaneous observations between 20 and 40 km

The vertical distribution of stratospheric ozone has been simultaneously measured by means of five different instruments carried on the same balloon payload. The launches were performed from Gap during the intercomparison campaign conducted in June 1981 in southern France. Data obtained between altitudes of 20 and 40 km are compared and discussed. Vertical profiles deduced from Electrochemical Concentration Cell sondes launched from the same location by small balloons and from short Umkehr measurements made at Mt Chiran (France) are also included in this comparison. Systematic differences of the order of 20 percent between ozone profiles deduced from solar u.v. absorption and in situ techniques are found.

Aimedieu, P.↗

Ozone profiling from backscattered UV radiance measurements A new procedure

This paper presents a data analysis technique that has been developed to support a stratospheric ozone measurement and profiling program. The data consist of solar backscattered UV radiation monitored by a spacecraft. The output consists of ozone mixing ratio profiles complete with error bars throughout the atmosphere. The technique is based upon principles of nonlinear optimal estimation. It provides a number of desirable features that have not been available together in any previously constructed technique for the problem. Iteration on both radiation measurements and total ozone measurements is among these features.

Whitney, C. K.↗