Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE FIELD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

A Patch Density Recommendation based on Convergence Studies for Vehicle Panel Vibration Response resulting from Excitation by a Diffuse Acoustic Field

Producing fluid structural interaction estimates of panel vibration from an applied pressure field excitation are quite dependent on the spatial correlation of the pressure field. There is a danger of either over estimating a low frequency response or under predicting broad band panel response in the more modally dense bands if the pressure field spatial correlation is not accounted for adequately. It is a useful practice to simulate the spatial correlation of the applied pressure field over a 2d surface using a matrix of small patch area regions on a finite element model (FEM). Use of a fitted function for the spatial correlation between patch centers can result in an error if the choice of patch density is not fine enough to represent the more continuous spatial correlation function throughout the intended frequency range of interest. Several patch density assumptions to approximate the fitted spatial correlation function are first evaluated using both qualitative and quantitative illustrations. The actual response of a typical vehicle panel system FEM is then examined in a convergence study where the patch density assumptions are varied over the same model. The convergence study results illustrate the impacts possible from a poor choice of patch density on the analytical response estimate. The fitted correlation function used in this study represents a diffuse acoustic field (DAF) excitation of the panel to produce vibration response.

Smith, Andrew↗
NASA NTRS1991

Spray combustion under oscillatory pressure conditions

The performance and stability of liquid rocket engines is often argued to be significantly impacted by atomization and droplet vaporization processes. In particular, combustion instability phenomena may result from the interactions between the oscillating pressure field present in the rocket combustor and the fuel and oxidizer injection process. Few studies have been conducted to examine the effects of oscillating pressure fields on spray formation and its evolution under rocket engine conditions. The pressure study is intended to address the need for such studies. In particular, two potentially important phenomena are addressed in the present effort. The first involves the enhancement of the atomization process for a liquid jet subjected to an oscillating pressure field of known frequency and amplitude. The objective of this part of the study is to examine the coupling between the pressure field and or the resulting periodically perturbed velocity field on the breakup of the liquid jet. In particular, transverse mode oscillations are of interest since such modes are considered of primary importance in combustion instability phenomena. The second aspect of the project involves the effects of an oscillating pressure on droplet coagulation and secondary atomization. The objective of this study is to examine the conditions under which phenomena following the atomization process are affected by perturbations to the pressure or velocity fields. Both coagulation and represent a coupling mechanism between the pressure field and the energy release process in rocket combustors. It is precisely this coupling which drives combustion instability phenomena. Consequently, the present effort is intended to provide the fundamental insights needed to evaluate these processes as important mechanisms in liquid rocket instability phenomena.

Jacobs, H. R.↗
NASA NTRS2013

A Patch Density Recommendation based on Convergence Studies for Vehicle Panel Vibration Response resulting from Excitation by a Diffuse Acoustic Field

Fluid structural interaction problems that estimate panel vibration from an applied pressure field excitation are quite dependent on the spatial correlation of the pressure field. There is a danger of either over estimating a low frequency response or under predicting broad band panel response in the more modally dense bands if the pressure field spatial correlation is not accounted for adequately. Even when the analyst elects to use a fitted function for the spatial correlation an error may be introduced if the choice of patch density is not fine enough to represent the more continuous spatial correlation function throughout the intended frequency range of interest. Both qualitative and quantitative illustrations evaluating the adequacy of different patch density assumptions to approximate the fitted spatial correlation function are provided. The actual response of a typical vehicle panel system is then evaluated in a convergence study where the patch density assumptions are varied over the same finite element model. The convergence study results are presented illustrating the impact resulting from a poor choice of patch density. The fitted correlation function used in this study represents a Diffuse Acoustic Field (DAF) excitation of the panel to produce vibration response.

Smith, Andrew↗
NASA NTRS1975

Noncompact source effect on the prediction of tone noise from a fan rotor

A comparison is made between the conventional compact source prediction for airfoil sound radiation and the rigorous prediction based on distributed sources along the airfoil chord. The theoretical analysis performed is for a single airfoil and cascaded airfoils immersed in a sinusoidally varying convected gust field. The pressure field around a single airfoil in supersonic gust flows is also studied. In subsonic flows the phase change of unsteady lift along the chord of a single airfoil reduces the sound radiation significantly in the upstream direction and increases the downstream radiation compared to the compact source prediction. In supersonic flows the compact source prediction gives substantial error in the region just behind the Mach wedge originating from the leading edge, while it approaches the noncompact source results far downstream from the airfoil. In the case of cascaded airfoils the compact source prediction overestimates the upstream radiation by as much as 20 dB depending on frequency and interblade phase.

Kaji, S.↗
NASA NTRS1979

Investigation of surface fluctuating pressures on a 1/4 scale YC-14 upper surface blown flap model

Fluctuating pressures were measured at 30 positions on the surface of a 1/4-scale YC-14 wing and fuselage model during an outdoor static testing program. These data were obtained as part of a NASA program to study the fluctuating loads imposed on STOL aircraft configurations and to further the understanding of the scaling laws of unsteady surface pressure fields. Fluctuating pressure data were recorded at several discrete engine thrust settings for each of 16 configurations of the model. These data were reduced using the technique of random data analysis to obtain auto-and cross-spectral density functions and coherence functions for frequencies from 0 to 10 kHz, and cross-correlation functions for time delays from 0 to 10.24 ms. Results of this program provide the following items of particular interest: (1) Good collapse of normalized PSD functions on the USB flap was found using a technique applied by Lilley and Hodgson to data from a laboratory wall-jet apparatus. (2) Results indicate that the fluctuating pressure loading on surfaces washed by the jet exhaust flow was dominated by hydrodynamic pressure variations, loading on surface well outside the flow region dominated by acoustic pressure variations, and loading near the flow boundaries from a mixture of the two.

Pappa, R. S.↗
NASA NTRS1982

Improved Venus ionopause altitude calculation and comparison with measurement

Improved approximations are incorporated into the inviscid fluid method originated by Spreiter et al (1970) in calculations of the altitude of the Venus ionopause. The altitude calculations are then compared with median altitudes measured by the Pioneer Venus retarding potential analyzer. The calculated ionopause shape is found to closely approximate the measured meridian shape in the solar zenith angle (SZA) range of zero-135 deg. The use of improved ionospheric pressure field ionosheath pressure and Prandtl-Meyer expansion approximations lowers the terminator ionopause altitude to approximately half that obtained with the usual Spreiter approximations. It is also determined that the calculated dawn ionopause is about 300 km higher than the dusk ionopause, and that both ionopauses are close to their respective measured meridian values. It is concluded that median ionopause altitude within the SZA angle range may be calculated without inclusion of a viscous interaction in the theory.

Knudsen, W. C.↗
NASA NTRS1988

Instability and sound emission from a flow over a curved surface

The growth and decay of a wavepacket convecting in a boundary layer over a concave-convex surface is studied numerically using direct computations of the Navier-Stokes equations. The resulting sound radiation is computed using the linearized Euler equations with the pressure from the Navier-Stokes solution as a time-dependent boundary condition. It is shown that on the concave portion the amplitude of the wavepacket increases and its bandwidth broadens while on the convex portion some of the components in the packet are stabilized. The pressure field decays exponentially away from the surface and then algebraically exhibits a decay characteristic of acoustic waves in two dimensions. The far-field acoustic pressure exhibits a peak at a frequency corresponding to the inflow instability frequency.

Maestrello, L.↗
NASA NTRS1993

Verification of thermal analysis codes for modeling solid rocket nozzles

One of the objectives of the Solid Propulsion Integrity Program (SPIP) at Marshall Space Flight Center (MSFC) is development of thermal analysis codes capable of accurately predicting the temperature field, pore pressure field and the surface recession experienced by decomposing polymers which are used as thermal barriers in solid rocket nozzles. The objective of this study is to provide means for verifications of thermal analysis codes developed for modeling of flow and heat transfer in solid rocket nozzles. In order to meet the stated objective, a test facility was designed and constructed for measurement of the transient temperature field in a sample composite subjected to a constant heat flux boundary condition. The heating was provided via a steel thin-foil with a thickness of 0.025 mm. The designed electrical circuit can provide a heating rate of 1800 W. The heater was sandwiched between two identical samples, and thus ensure equal power distribution between them. The samples were fitted with Type K thermocouples, and the exact location of the thermocouples were determined via X-rays. The experiments were modeled via a one-dimensional code (UT1D) as a conduction and phase change heat transfer process. Since the pyrolysis gas flow was in the direction normal to the heat flow, the numerical model could not account for the convection cooling effect of the pyrolysis gas flow. Therefore, the predicted values in the decomposition zone are considered to be an upper estimate of the temperature. From the analysis of the experimental and the numerical results the following are concluded: (1) The virgin and char specific heat data for FM 5055 as reported by SoRI can not be used to obtain any reasonable agreement between the measured temperatures and the predictions. However, use of virgin and char specific heat data given in Acurex report produced good agreement for most of the measured temperatures. (2) Constant heat flux heating process can produce a much higher heating rate than the radiative heating process. The results show that heating rates of 125 C/s (225 F/s) can be achieved. (3) The electrical resistance of the FM 5055 samples were about 150 Omega in the virgin state, and decreased to about 35 Omega when charred. A reliable scheme must be developed to electrically insulate the composite from the heater foil in order to prevent any current leakage into the sample which can result in volumetric heating of the char zone of the composite.

Keyhani, M.↗
NASA NTRS2001

Predicting the Rotor-Stator Interaction Acoustics of a Ducted Fan Engine

A Navier-Stokes computation is performed for a ducted-fan configuration with the goal of predicting rotor-stator noise generation without having to resort to heuristic modeling. The calculated pressure field in the inlet region is decomposed into classical infinite-duct modes, which are then used in either a hybrid finite-element/Kirchhoff surface method or boundary integral equation method to calculate the far field noise. Comparisons with experimental data are presented, including rotor wake surveys and far field sound pressure levels for two blade passage frequency (BPF) tones.

Biedron, Robert T.↗
NASA NTRS2001

Predicting the Rotor-Stator Interaction Acoustics of a Ducted Fan Engine

A Navier-Stokes computation is performed for a ducted-fan configuration with the goal of predicting rotor-stator noise generation without having to re- to heuristic modeling. The calculated pressure field in the inlet region is decomposed into classical infinite-duct, modes, which are then used in either a hybrid finite-element /Kirchhoff surface method or boundary integral equation method to calculate the far field noise. Comparisons with experimental data are presented, including rotor wake surveys and far field sound pressure levels for 2 blade passage frequency (BPF) tones.

Biedron, Robert T.↗
NASA NTRS1996

Modeling of Sound Transmission through Shell Structures with Turbulent Boundary Layer Excitation

The turbulent boundary layer (TBL) pressure field is an important source of cabin noise during cruise of high subsonic and supersonic commercial aircraft. The broadband character of this excitation field results in an interior noise spectrum that dominates the overall sound pressure level (SPL) and speech interference metrics in the forward and midcabins of many aircraft. In the authors' previous study, sound transmission through an aircraft fuselage, modeled by two concentric cylindrical sandwich shells and excited by a TBL statistical model was investigated analytically. An assessment of point and global structural vibration levels and resulting interior noise levels was obtained for different TBL models, flight conditions and fuselage structural designs. However, due to the complication of the shell structure, the important noise transmission mechanisms were difficult to discern. Previous experience has demonstrated that a fundamental understanding of the range of modes (or wavenumbers) generated by the TBL source both in the structure and the acoustic cavity is key to the development of both active and passive control technologies. In an initial effort to provide this insight, the objective of this paper is to develop an analytical model of sound transmission through a simple unstiffened cylindrical aluminum shell excited by a TBL pressure field. The description of the turbulent pressure field is based on the Corcos formulation for the cross-spectral density (CSD) of the pressure fluctuations. The coupled shell and interior and exterior acoustic equations are solved for the structural displacement and the interior acoustic response using a Galerkin approach to obtain analytical solutions. Specifically, this study compares the real part of the normalized CSD of the TBL excitation field, the structural displacement and the interior acoustic field. Further the modal compositions of the structural and cavity response are examined and some inference of the dominant mechanism of noise transmission is made.

Tang, Yvette Y.↗
NASA NTRS1986

Flow field and near and far sound field of a subsonic jet

Flow and sound field data are presented for a 2.54 cm diameter air jet at a Mach number of 0.50 and a Reynolds number of 300,000. Distributions of mean velocity, turbulence intensities, Reynolds stress, spectral components of turbulence as well as of the near field pressure, together with essential characteristics of the far field sound are reported. This detailed set of data for one particular flow, erstwhile unavailable in the literature, is expected to help promoote and calibrate subsonic jet noise theories. 'Source locations' in terms of the turbulence maxima, coupling between the entrainment dynamics and the near pressure field, the sound radiation paths, and the balance in mass, momentum and sound energy fluxes are discussed. The results suggest that the large scale coherent structures of the jet govern the 'source locations' by controlling the turbulence and also strongly influence the near field pressure fluctuations.

Zaman, K. B. M. Q.↗
NASA NTRSDate not supplied

USM3D Simulations for Third Sonic Boom Workshop

The NASA USM3D flow solver was used to compute test cases for the Third AIAA Sonic Boom Prediction Workshop (SBPW3). The test cases include a nearfield biconvex shock-plume interaction wind tunnel model, and the C608 Low Boom Flight Demonstrator. Numerical simulations were conducted on the mixed-element and tetrahedral grids provided by the workshop committee, as well as a family of grids generated by an in-house approach for sonic boom analyses known as BoomGrid. The near-field pressure signatures were extracted, propagated to the ground and the perceived loudness levels on the ground were computed. The USM3D near-field pressure signatures, corresponding ground signatures, and loudness levels on the ground are compared with that of mean values from other workshop participants. The effect of three flux-limiters on the accuracy of near-field pressure signatures prediction was investigated and results are compared with that of mean values from other workshop participants. The effect of using wall function grids in accurately predicting near-field pressure signatures was also evaluated.

Supersonics↗
NASA NTRSDate not supplied

USM3D Simulations for the Third Sonic Boom Prediction Workshop (SBPW-3)

The NASA USM3D flow solver was used to compute test cases for the Third AIAA Sonic Boom Prediction Workshop (SBPW3). The test cases include a nearfield biconvex shock-plume interaction wind tunnel model, and the C608 Low Boom Flight Demonstrator. Numerical simulations were conducted on the mixed-element and tetrahedral grids provided by the workshop committee, as well as a family of grids generated by an in-house approach for sonic boom analyses known as BoomGrid. The near-field pressure signatures were extracted, propagated to the ground and the perceived loudness levels on the ground were computed. The USM3D near-field pressure signatures, corresponding ground signatures, and loudness levels on the ground are compared with that of mean values from other workshop participants. The effect of three flux-limiters on the accuracy of near-field pressure signatures prediction was investigated and results are compared with that of mean values from other workshop participants. The effect of using wall function grids in accurately predicting near-field pressure signatures was also evaluated.

Supersonics↗
NASA NTRSDate not supplied

Analysis of Transonic Unsteady Aerodynamic Environments using Unsteady Pressure Sensitive Paint for the Space Launch System Block 1 Cargo Launch Vehicle

Predicting launch vehicle unsteady aerodynamic loads due to buffet remains a significant challenge. Current practices for modeling buffet environments involve the development of buffet forcing functions using unsteady pressure measurements acquired during wind-tunnel tests. These practices often result in significant uncertainty in buffet environments for coupled loads analyses due to the complex spatio-temporal nature of the unsteady pressure field and challenge of its estimation using discrete sensors. Unsteady pressure sensitive paint, on the other hand, can provide unsteady pressure data at a comparatively high-spatial-density and may overcome the challenge of unsteady pressure field estimation with discrete sensors and lead to improvements in the development of buffet forcing functions. In this paper, comparisons of the fluctuating pressure field are made for the Space Launch System Block 1 cargo launch vehicle measured using unsteady pressure sensitive paint and pressure transducers.

buffet↗
NASA NTRS1984

Effects of the pressure perturbation field in numerical models of unidirectionally sheared thunderstorm convection - Two versus three dimensions

The physical roles of 'buoyant' and 'dynamic' pressure components, and the distinction between buoyant and hydrostatic pressure perturbations, are aspects of the pressure perturbation field in strongly sheared convective storms studied by means of two- and three-dimensional anelastic numerical modeling experiments with common environmental profiles. The pressure analysis clarifies the differences between two- and three-dimensional storms. In the main updraft, strong midlevel thermal buoyancy is partly opposed by a downward-perturbed vertical pressure gradient force. This, however, occurs to a much greater extent in two dimensions than in three, contributing to smaller net upward accelerations. While the buoyant and hydrostatic fields are intimately related to the total buoyancy distribution, the buoyant pressure perturbation is smoother and of lower amplitude than its hydrostatic counterpart. For the model experiments, this distinction is far greater in three dimensions than in two, in association with the smaller scale of the active convection in three dimensions.

Schlesinger, R. E.↗