Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Acoustics and Surface Pressure Measurements from Tandem Cylinder Configurations

Acoustic and unsteady surface pressure measurements from two cylinders in tandem configurations were acquired to study the effect of spacing, surface trip and freestream velocity on the radiated noise. The Reynolds number ranged from 1.15x10(exp 5) to 2.17x10(exp 5), and the cylinder spacing varied between 1.435 and 3.7 cylinder diameters. The acoustic and surface pressure spectral characteristics associated with the different flow regimes produced by the cylinders' wake interference were identified. The dependence of the Strouhal number, peak Sound Pressure Level and spanwise coherence on cylinder spacing and flow velocity was examined. Directivity measurements were performed to determine how well the dipole assumption for the radiation of vortex shedding noise holds for the largest and smallest cylinder spacing tested.

Hutcheson, Florence V.↗
NASA NTRS1975

Effects of transducer flushness on fluctuating surface pressure measurements

The installation flushness of pressure transducers has been found to strongly influence the quality of fluctuating surface pressure data in supersonic-attached turbulent boundary-layer flow. A systematic investigation of the effects of flushness on surface pressure fluctuations beneath a 4-in.-thick boundary layer was conducted in a supersonic wind tunnel at Mach numbers of 1.68, 2.0, and 2.5. Flushness effects on transducer signal amplitude, power spectral density, coherence, and narrowband convection velocity was evaluated. Results show that a very slightly protruding transducer produces adverse effects on the desired pressure fluctuation measurements, whereas a submerged transducer produces small effects. Indications are that a more viable method for enhancing the uniformity and spatial correlation of fluctuating surface pressure data can be achieved by deliberately submerging transducers beneath a surface orifice about 0.010 in. deep.

Hanly, R. D.↗
NASA NTRS1987

Chordwise pressure measurements on a blade of Mod-2 Wind Turbine

Pressure measurements covering a range of wind velocities were made at one span location on a blade of the Mod-2 Wind Turbine. The data show the existence of higher pressure coefficients than would be expected from wind tunnel data. These high pressure coefficients may be the result of three-dimensional flow over the blade that delays flow separations. Data is presented showing the repetitiveness and abrupt changes in the pressure distribution that occurs as the blade rotates. Calculated values of suction and flap coefficients are also presented.

Nyland, T. W.↗
NASA NTRSDate not supplied

Steady Surface Pressure Measurement via the Lifetime Method With High-Speed Cameras in NASA's Unitary Plan Wind Tunnel

High spatial resolution measurement of steady surface pressure via pressure-sensitive paint at NASA Ames has traditionally relied on specialized cameras equipped to accumulate charge over multiple exposures, whereas measurement of the fluctuating component of pressure uses an altogether separate set of high-speed cameras. To reduce complexity of installation, data acquisition, and processing, we have implemented methods to use a single set of commercial off-the-shelf cameras to produce both steady and unsteady pressure measurements. Both imaging systems were installed in the 11-by 11-foot NASA Ames Unitary Plan Wind Tunnel and acquired images of a scaled model of the Space Launch System Block 1B Crew and Cargo configurations over a variety of flow conditions. This work focuses on methods for data acquisition, processing, and calibration to produce steady-state pressure estimates on the surface of the wind tunnel model based on the lifetime method. It will then compare the steady solutions produced by the legacy and high-speed imaging systems.

Pressure Sensitive Paint↗
NASA NTRS1991

Static pressure measurements in A 30 kWe class arcjet

A series of cold and hot flow static pressure measurements have been made as a function of distance along the principal axis of a 30 kWe arcjet. During these experiments, the background pressure was varied from atmospheric pressure to less than 1 Torr. The experimental arcjet used in these tests had the same constrictor and conical nozzle dimensions as the baseline MOD-1 ammonia arcjet developed at NASA-JPL, but used nitrogen as the propellant gas. Comparison of the measured static pressure profiles with the arc erosion patterns on the anode surface showed that anode arc attachment points directly coincided with the minimum static pressure points. The dual voltage modes commonly observed in 30 kWe class arcjet thrusters are also believed to be caused by the presence of two pressure minima in the arcjet, one at the constrictor entrance and the other in the expansion nozzle. The static pressure profiles also suggest that the sonic flow transition occurs at the entrance to the nozzle, indicating the existence of very thick boundary layers in the arcjet constrictor.

Harris, William J.↗
NASA NTRS1984

An experimental investigation of surface pressure measurements on an advanced winged entry vehicle at Mach 10

Surface pressure measurements have been made at Mach 10 in air on an instrumented 0.006-scale model of an advanced (control configured) winged entry vehicle. The tests were conducted in the Langley Continuous Flow Hypersonic Tunnel. Data were obtained at 83 surface pressure stations, which include locations on the lower and upper surface centerlines, spanwise positions along the lower and upper surfaces of the wing, the lower surface of the body flap, and radial locations on the fuselage. Data were obtained for angles of attack ranging from zero to 40 deg, sideslip angles of -2 deg to +5 deg, Reynolds numbers of 0.5, 1.0, and 2.0 million per foot, and body-flap deflections of zero, 10, and 20 deg. Test conditions and orifice locations were chosen to correspond directly with those for the heat transfer measurements previously reported on the same configuration. Comparison of windward symmetry plane data with predictions based upon an approximate engineering method was found to yield reasonable agreement for angles of attack from 20 to 40 deg. The leeward surface pressure data were observed to be roughly an order of magnitude lower than the corresponding windward data. At low angles of attack, regions of high pressure were noted on the windward wing surface. The result is attributed to vortical action or shock impingement. High pressures were also measured on the deflected body flap, a critical region for this type of vehicle. Reynolds number effects were found to be insignificant.

Wurster, K. E.↗
NASA NTRS2005

An Evaluation of Measured Pressure Signatures From Wind-Tunnel Models of Three Low-Boom Concepts

Revised 1990-1991 sonic-boom design and analysis methodology was assessed by applying it to the design of three low-boom concepts. Models of these concepts were built and used to measure pressure signatures in the wind tunnel. An analysis of wind-tunnel data showed unexpected nacelle-inlet and the nacelle-wing interference-lift shocks in the pressure signatures from the two engine-under-the-wing models, but not in the measured pressure signatures from the wind-tunnel model with the engine nacelles mounted on the aft fuselage. However, additional lift-induced shocks were found in the pressure signature data from all three wind-tunnel models indicating that other flow-field disturbance effects were present.

Mack, Robert J.↗
NASA NTRS1961

Free-Flight Skin-Temperature and Surface-Pressure Measurements on a Highly Polished Nose Having a 100 deg Total-Angle Cone and a 10 deg Half-Angle Conical Flare Section up to a Mach Number of 4.08

The skin temperature and surface pressure were measured on a large-scale, highly polished nose having a relatively sharp-tipped 100 deg total-angle cone followed by a conical flare section of 10 deg half-angle. The measurements were obtained in flight from a rocket-propelled model up to a peak Mach number of 4.08 and a peak Reynolds number of 22 x 10(exp 6) per foot. Temperature distributions indicated that the heating on the forward 3.5 inches of the 100 deg cone was lower than the heating on the rearward portion. Likewise, measured temperatures on the flare portion of the test nose were generally lower than the temperatures on the 100 deg cone portion. The data indicated that the local Reynolds numbers of transition, based on calculated boundary-layer momentum thicknesses, ranged from 530 to 940 for a Mach number range from 2.72 to 3.75. Comparison of measured cone pressures with theory for a sharp cone showed that theory overestimates the cone pressures. Pressure measurements on the flare portion of the nose showed that in the lower speed range the flow expands below atmospheric pressure in going from the cone to the flare; however, as the speed increased, the expansion diminished and for speeds greater than a Mach number of approximately 3.0 the flare pressure coefficients were at or near a value of zero.

Rashis, Bernard↗
NASA NTRS1989

Flight evaluation of a pneumatic system for unsteady pressure measurements using conventional sensors

A flight experiment was conducted to evaluate a pressure measurement system which uses pneumatic tubing and remotely located electronically scanned pressure transducer modules for in-flight unsteady aerodynamic studies. A parametric study of tubing length and diameter on the attenuation and lag of the measured signals was conducted. The hardware was found to operate satisfactorily at rates of up to 500 samples/sec per port in flight. The signal attenuation and lag due to tubing were shown to increase with tubing length, decrease with tubing diameter, and increase with altitude over the ranges tested. Measurable signal levels were obtained for even the longest tubing length tested, 4 ft, at frequencies up to 100 Hz. This instrumentation system approach provides a practical means of conducting detailed unsteady pressure surveys in flight.

Curry, Robert E.↗
NASA NTRS1990

Adaptation of electronically scanned pressure measurement technology at Langley Research Center

The use of pressure-measurement devices based on electronic scanning in wind-tunnel and other settings with harsh conditions is discussed in terms of adaptations required to protect the integrity of the devices and output data. The applications considered include thermal extremes, long cable lengths, very low pressure, high-line pressure, and variable-reference calibrations. Some of the adaptation techniques are thermal enclosures, remote power supplies, low-pressure standards, and biasing regulators.

Mitchell, Michael↗
NASA NTRS1978

Correlation of combustor acoustic power levels inferred from internal fluctuating pressure measurements

Combustion chamber acoustic power levels inferred from internal fluctuating pressure measurements are correlated with operating conditions and chamber geometries over a wide range. The variables include considerations of chamber design (can, annular, and reverse-flow annular) and size, number of fuel nozzles, burner staging and fuel split, airflow and heat release rates, and chamber inlet pressure and temperature levels. The correlated data include those obtained with combustion component development rigs as well as engines.

Vonglahn, U. H.↗