SEARCH · Search NASA

Results for “Parameter optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Digital Twin Model for Advanced Manufacture of a Rotating Detonation Engine Injector

A digital twin material model (DTMM) of an additive manufacturing (AM) process was created to advance the state of the art in rotating detonation engine (RDE) injector design. Current RDE injectors are designed with large pressure drops, enabling a stable and repeatable combustion process. However, this comes at the cost of system efficiency. For the technology to transition to commercial fossil-based power generation, it is important to develop injectors with reduced flow losses. Low-loss injectors are difficult to design and manufacture with conventional manufacturing techniques. AM enables new design options, but the AM manufacturing process must be thoroughly understood to result in a robust design. A DTMM provides the necessary insight by defining the cause-effect relationships between process parameters, microstructure features, and properties. Therefore, a DTMM to support the design and manufacturing process was developed and applied to the design of a new additively manufactured low-loss injector. The injector combustion behavior was characterized through hot-fire tests, and mechanical performance was compared to the DTMM predictions. The two project goals were the successful development of the DTMM and the demonstration of an improved RDE injector design. The RDE injector design and DTMM developments occurred on parallel but dependent paths. The injector was designed to reduce pressure drop by increasing the cross-sectional flow area ratio between the injector air passages and the combustor annulus. This resulted in less structural material, raising the concern that thin members would be susceptible to high-cycle fatigue (HCF) under the periodic loading inherent to an RDE. It was most important for the DTMM to predict behavior in these features; therefore, the injector design concept guided the material thicknesses used in fatigue tests. The DTMM development started by manufacturing a series of coupons over the range of possible AM process variations. A design-of-experiment approach was used to select which process variable combinations gave the most efficient coverage relevant to the injector design space. The microstructure in each of these coupons was characterized, and then computational methods were used to create a numerical model of the correlation between process variables and microstructure. Next, a set of HCF samples were tested to calibrate existing models that map microstructure to HCF performance. Together, these two links formed the DTMM that calculates HCF behavior from AM process variables. Two injector prototypes were additively manufactured. The first injector design strategy aggressively pursued low-loss performance by substantially increasing the oxidizer flow area. The combination of manufacturing lead times and the fatigue testing schedule meant that the DTMM was not available when building this first prototype. Therefore, its process parameters were chosen based on a manual review of the available coupon data. This prototype was built successfully and evaluated in 58 combustion tests. Sustained detonation was achieved with remarkably reduced pressure loss, and some tests even displayed pressure loss characteristics similar to conventional gas turbine combustors. This achieved the project goal of improving RDE injector design. The second injector was manufactured according to the optimized parameters predicted by the DTMM. The flow area modifications of this injector were less aggressive than the first injector since demonstrating low pressure loss was not an objective of the second hot-fire test series. Rather, the test objective was to cause high cycle fatigue failure in the part due to periodic loading from the rotating detonation wave. The observed number of cycles to failure was to be compared to the number predicted by the DTMM and thereby assess the utility of the DTMM in component design. However, the required level of vibration was not obtained during combustion. Therefore, high cycle fatigue was not experienced in the hot-fire tests of the second injector. Fatigue data was obtained by further testing the second injector in a conventional HCF test apparatus. The injector demonstrated HCF strength above the DTMM prediction. In fact, it did not fail and testing was only discontinued due to reaching the end of the period of performance. This points to some success in the project’s primary goal of successfully developing and applying the DTMM to a component design. Implementing the DTMM recommendations for optimal processing parameters led to a part with acceptable properties. The DTMM was also shown to be an efficient correlator of data and to provide insight into the relationship between process settings, microstructure, and property performance. However, the failure of the DTMM prediction to match the experimental result of the injector fatigue test also points to the need to include significantly more data in the model development. In this project, coupons made with identical processing parameters exhibited drastically different properties from each other and from the injector part, which clearly influences the accuracy of a model that predicts performance based on parameters. Uncertainties in the build process must be quantified to develop more robust models. A denser and broader matrix of coupon process and geometry variations, several repeated builds of every point, more in-situ build process measurements, and direct observation of tensile and HCF sample microstructure (as opposed to separate microstructure specimens) are recommendations to improve future AM modeling efforts.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2020

Machine learning the Hubbard U parameter in DFT+U using Bayesian optimization

Abstract Within density functional theory (DFT), adding a Hubbard U correction can mitigate some of the deficiencies of local and semi-local exchange-correlation functionals, while maintaining computational efficiency. However, the accuracy of DFT+U largely depends on the chosen Hubbard U values. We propose an approach to determining the optimal U parameters for a given material by machine learning. The Bayesian optimization (BO) algorithm is used with an objective function formulated to reproduce the band structures produced by more accurate hybrid functionals. This approach is demonstrated for transition metal oxides, europium chalcogenides, and narrow-gap semiconductors. The band structures obtained using the BO U values are in agreement with hybrid functional results. Additionally, comparison to the linear response (LR) approach to determining U demonstrates that the BO method is superior.

Chemistry↗

DOE OSTI2020

Fast strength model characterization using Bayesian statistics

A variety of flow stress models exist with new models constantly being developed. These models aim to approximate the strength of materials in a variety of regimes from quasistatic loading through shock scenarios. All models contain an array of parameters which need to be tuned to the material under study. Some models perform well under limited conditions, requiring adjustment of the parameters when venturing outside of those predefined ranges. Other models perform well over a wide range of conditions with a set of parameters, but may be outperformed by other models optimized on a tighter range of conditions. Recent research by Los Alamos demonstrated the ability to optimize the Johnson Cook (JC) model using a set of 3 plate-impact experiments on Aluminum. They utilized Bayesian statistics and emulation to determine optimal parameters for the model with a quantification of parameter uncertainty. We present an extension of this capability to incorporate velocimetry from plate-impact tests, stress-strain data from split Hopkinson pressure bar and quasistatic compression tests, plus profiles from Taylor cylinders in a unified fashion. Statistically robust comparisons of the performance and uncertainty of different realizations of the JC flow stress model were carried out based on calibration to several possible combinations of these three different experiment types.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

HGQ: High Granularity Quantization for Real-time Neural Networks on FPGAs

Neural networks with sub-microsecond inference latency are required by many critical applications. Targeting such applications deployed on FPGAs, we present High Granularity Quantization (HGQ), a quantization-aware training framework that optimizes parameter bit-widths through gradient descent. Unlike conventional methods, HGQ determines the optimal bit-width for each parameter independently, making it suitable for hardware platforms supporting heterogeneous arbitrary precision arithmetic. In our experiments, HGQ shows superior performance compared to existing network compression methods, achieving orders of magnitude reduction in resource consumption and latency while maintaining the accuracy on several benchmark tasks. These improvements enable the deployment of complex models previously infeasible due to resource or latency constraints. HGQ is open-source and is used for developing next-generation trigger systems at the CERN ATLAS and CMS experiments for particle physics, enabling the use of advanced machine learning models for real-time data selection with sub-microsecond latency.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2025

Classical optimization with imaginary-time block encoding on quantum computers: The MaxCut problem

Optimization problems in finance, physics, and computer science are typically very hard to tackle in classical computing; quantum computing could help speed up computations and provide efficient methods for tackling large problems. Typically, to treat a problem with a quantum computer, the optimal solution is cast as the ground state of a diagonal Hamiltonian. Here, we develop a method, called imaginary-time evolution block encoding (ITE-BE), based on a recent imaginary-time algorithm, which requires no variational parameter optimization, as all parameters can be derived analytically from the target Hamiltonian. We also demonstrate that our method can be successfully combined with other quantum algorithms such as the quantum approximate optimization algorithm (QAOA). For illustration, here we study the MaxCut problem. We find that the QAOA ansatz increases the postselection success of ITE-BE, and shallow QAOA circuits, when boosted with ITE-BE, achieve better performance than deeper QAOA circuits. For the special case of the transverse initial state, we adapt our block-encoding scheme to allow for a deterministic application of the first layer of the circuit.

Zhong, Dawei [University of Southern California, L↗

DOE OSTI2024

Impact of the Exciter and Governor Parameters on Forced Oscillations

In recent years, the frequency of forced oscillation events due to control system malfunctions or improper parameter settings has increased. Tuning the parameters of exciters and governor models is crucial for maintaining power system stability. Traditional simulation studies typically involve small transient disturbances or step changes to find optimal parameter sets, but existing optimization algorithms often fall short in fine-tuning for forced oscillations. Identifying the sensitive parameters within these control models is essential for ensuring stability during large, sustained disturbances. This study focuses on identifying these critical exciter and governor model parameters by analyzing their influence on sustained forced oscillations. Using Kundur’s two-area system, we analyze common exciter models such as SCRX, ESST1A, and AC7B, along with governor models like GAST, HYGOV, and GGOV1, utilizing PSS®E software version 34. Sustained forced oscillations are injected at generator-1 of area-1, with individual parameter changes dynamically simulated. By considering a local oscillation frequency of 1.4 Hz and an inter-area oscillation mode of 0.25 Hz, we analyze the impact of each parameter change on the magnitude and frequency of forced oscillations as well as on active and reactive power outputs. This novel approach highlights the most influential parameters of each tested model—such as exciter, governor, and turbine gains, as well as time constant parameters—on the impact of forced oscillations. Based on our findings, the sensitive parameters of each tested model are ranked. These would provide valuable insights for industry operators to fine-tune control settings during oscillation events, ultimately enhancing system stability.

42 ENGINEERING↗

DOE OSTI2025

A high-throughput approach for statistical process optimization in Laser Powder Bed Fusion

Process variability is inherent in metal additive manufacturing (AM). However, it is often overlooked in process optimization frameworks, constraining the understanding of process uncertainties and their influence on parameter selection. To address this, we present an integrated framework that combines high-throughput single-track experiments, GAN-based melt pool geometry extraction, robust statistical and machine learning modeling, and uncertainty-quantified process mapping. Process variability is characterized through single-track melt pool behaviors, and its influence on defect formation is systematically quantified to enable statistically guided process parameter optimization. This approach is demonstrated on Laser Powder Bed Fusion (L-PBF) of stainless steel 316L, effectively capturing the interplay between process parameters, melt pool variability, and defect probability. By integrating uncertainty quantification into process optimization, this study provides a structured methodology for addressing variability challenges in AM quality control, ultimately contributing to enhanced manufacturing reliability.

Laser Powder Bed Fusion↗

DOE OSTI2024

Ion-chain sympathetic cooling and gate dynamics

Sympathetic cooling is a technique often employed to mitigate motional heating in trapped-ion quantum computers. However, choosing system parameters such as number of coolants and cooling duty cycle for optimal gate performance requires evaluating trade-offs between motional errors and other slower errors such as qubit dephasing. The optimal parameters depend on cooling power, heating rate, and ion spacing in a particular system. In this study, we aim to analyze best practices for sympathetic cooling of long chains of trapped ions using analytical and computational methods. We use a case study to show that optimal cooling performance is achieved when coolants are placed at the center of the chain and provide a perturbative upper bound on the cooling limit of a mode given a particular set of cooling parameters. In addition, using computational tools, we analyze the trade-off between the number of coolant ions in a chain and the center-of-mass mode heating rate. We also show that cooling as often as possible when running a circuit is optimal when the qubit coherence time is otherwise long. These results provide a roadmap for how to choose sympathetic cooling parameters to maximize circuit performance in trapped-ion quantum computers using long chains of ions.

Cooling & trapping↗

DOE OSTI2020

Dynamic Model Reduction for Large-Scale Power Systems Using Wide-Area Measurements

To perform faster than the real-time dynamic simulation of large-scale power systems, it is necessary to reduce the simulated system size by using equivalents for surrounding areas of the study area, and existing dynamic model reduction approach could provide the needed structure of the reduced area. However, further parameter optimization is required to achieve the desired accuracy. In this paper, a particle swarm optimization (PSO) based approach is used to solve the above problem. Parameters for the individual dynamic elements in the reduced system are calibrated repeatedly until the wide-area measurements of the reduced model and the original model are very similar to each other with satisfactory accuracy. Results indicate that after optimization, the dynamic response of the reduced model matches better with that of the original one than using existing methods. Under both the generator-trip event and the bus-fault event, the reduced model has a higher frequency match and less power mismatch.

42 ENGINEERING↗

DOE OSTI2022

ReNew100: Reliable Power System Operation with 100% Renewable Generation

The ReNew100 project has developed and demonstrated an operator support system (OSS) to operate power systems with 100% renewable power generation from inverter-based resources (IBRs) like wind and solar that significantly reduces the risk of widespread power outages in a simulated operational environment at Technology Readiness Level (TRL) 6. The OSS achieves resilient operation for power systems under changing operation modes including varying combinations of conventional and renewable generation, including cases with 100% renewable generation from wind and solar IBRs. The OSS continuously monitors the N-1 security of the power system, which refers to the ability of the power systems to survive single outages of power system elements, like the loss of a generator or a power line, without causing widespread power outages beyond those expected and planned for. If the OSS identifies that the system is not N-1 secure, an automatic Controller Parameter Optimization (CoPO) developed within Renew100 is activated to optimize the N-1 security of the system by tuning controller parameters within different assets like batteries, wind, and solar plants. The core innovation of ReNew100 is the development of this CoPO as well as the demonstration of the OSS for a real-time simulation of the Hawai'i Island power system. Moreover, Renew100 has developed new model calibration techniques for dynamic power system models and demonstrated them for Hawai'i Island.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2026

Use of friction stir processing to synthesize nanocrystalline, grain boundary segregating Fe-Ti alloys

Grain boundary segregating alloys, a class of alloys designed such that nanocrystalline grain sizes are thermodynamically stabilized by the presence of high segregation energy solutes at the grain boundaries, are typically produced through geometrically limited processing techniques such as equal channel angular extrusion or thin film sputtering. Here, this study explores the use of friction stir processing (FSP) as a novel means of studying and producing these alloys using a test system of Fe-6at%Ti. Spot FSPs with a range of processing parameter sets were produced on bulk, coarse grained bars of material and optimal parameters were identified. Microscopy identified a range of processed materials which achieved nanocrystalline grains on the order of 100 nm, delineating a critical window of processing parameters which limit heat input while inducing sufficient plastic deformation for grain refinement. The finest grained nanocrystalline Fe-Ti achieved a hardness of 7.68 GPa, a significant increase in hardness over pure Fe with a similar microstructure due to increased dislocation density from FSP as well as several strengthening mechanisms produced through the presence and segregation of Ti. These results demonstrated the feasibility of using FSP to produce nanocrystalline grain boundary segregating alloys.

Fe alloys↗

DOE OSTI2025

Accurate Force Field for Carbon Dioxide–Silica Interactions Based on Density Functional Theory

Fluid–silica interfaces are ubiquitous in chemistry, occurring in both natural geochemical environments and practical applications ranging from separations to catalysis. Simulations of these interfaces have been, and continue to be, a significant avenue for understanding their behavior. A constraining factor, however, is the availability of accurate force fields. Most simulations use traditional “mixing rules” to determine nonbonded dispersion interactions, an approach that has not been critically examined. Here, in this study, we present Lennard-Jones parameters for the interaction of carbon dioxide with silica interfaces that are optimized to reproduce density functional theory (DFT)-based binding energies. The modeling is based on the recently developed silica-DDEC force field, whose atomic charges are consistent with DFT calculations. Standard mixing rules are found to predict weaker CO 2 binding to silica than that obtained from DFT, an effect corrected by the optimized parameters given here. This behavior extends to other silica force fields (Clayff and Gulmen-Thompson), and the present Lennard-Jones parameters improve their performance as well. The effects of improved Lennard-Jones parameters on the structural and dynamical properties of condensed CO 2 in silica slit pores are also examined.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Models to Incorporate Reaction Mechanisms into DG-OSPREY: Fixed-Bed Simulations for Organic Iodides Capture Using Ag 0 Z

As one of the most potent radioisotopes released during spent nuclear fuel reprocessing, 129 I is strictly regulated and must be removed before discharge. Organic iodides (primarily alkyl iodides with different chain lengths, i.e., CH 3 I, C 4 H 9 I, and C 12 H 25 I) comprise ~2% of the total iodine in the reprocessing off-gases and are primarily present in vessel off-gas (VOG). Reduced silver mordenite (Ag 0 Z) is predominantly considered for the removal of radioiodine; however, its capture performance and underlying interaction processes with long-chain organic iodides are not fully understood. Two major tasks were accomplished in this study. First, to improve upon the previous experimental studies where Ag 0 Z was used to capture CH 3 I, C 4 H 9 I, and C 12 H 25 I at different concentrations, we comprehensively investigated the corresponding capture mechanisms by characterizing fully loaded Ag 0 Z samples. Second, computational codes were implemented to perform fixed-bed simulations that account for transport and reaction mechanisms. Scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), powder X-ray diffraction (PXRD), UV-visible diffuse reflectance spectroscopy (UV-vis DRS), and thermogravimetric analysis (TGA) were conducted on Ag 0 Z samples that are saturated with I 2 , CH 3 I, C 4 H 9 I, and C 12 H 25 I), respectively. Results indicate that AgI is the predominant adsorption product regardless of the adsorbed iodine species, yet alkyl iodides with different carbon chain lengths may have different compositions of α- and γ-AgI. Synchrotron pair distribution function (PDF) measurements and TGA coupled with a Fourier transformed infrared detector (TGA FTIR) have been performed, and experimental data are currently analyzed. Results are expected to provide further insights into the adsorption mechanisms. The fixed-bed capture performance for CH 3 I was successfully simulated by solving mathematical equations that describe the underlying transport processes and adsorption reactions. The computational framework, Catalytic After Treatment System (CATS), that was originated in our research group, was used to solve the governing equations. Kinetic parameters, including the pore diffusivity and reaction rate constant were obtained by optimization techniques using data from thin-bed experiments performed at Oak Ridge National Laboratory. The performance of a deep bed predicted using the optimized parameters showed promising agreement with the experimental data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Response Surface Methodology As a New Approach for Finding Optimal MALDI Matrix Spraying Parameters for Mass Spectrometry Imaging

Automated spraying devices have become ubiquitous in laboratories employing matrixassisted laser desorption/ionization mass spectrometry imaging (MALDI-MSI), in part because they permit control of a number of matrix application parameters that can easily be reproduced for intra- and interlaboratory studies. Determining the optimal parameters for MALDI matrix application, such as temperature, flow rate, spraying velocity, number of spraying cycles, and solvent composition for matrix application, is critical for obtaining high-quality MALDI-MSI data. However, there are no established approaches for optimizing these multiple parameters simultaneously. Instead optimization is performed iteratively (i.e., one parameter at a time), which is time consuming and can lead to overall non-optimal settings. In this report, we demonstrate the use a novel experimental design and the response surface methodology to optimize five parameters of MALDI matrix application using a robotic sprayer. Thirtytwo combinations of MALDI matrix spraying conditions were tested, which allowed us to elucidate relationships between each of the application parameters as determined by MALDI-MS (specifically, using a 15 Tesla Fourier transform ion cyclotron resonance mass spectrometer). As such, we were able to determine the optimal automated spraying parameters that minimized signal de-localization and enabled high MALDI sensitivity. We envision this optimization strategy can be utilized for other MALDI-MSI applications, tissue types, and matrix application approaches.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

Radar-Based Bayesian Estimation of Ice Crystal Growth Parameters within a Microphysical Model

The potential for polarimetric Doppler radar measurements to improve predictions of ice microphysical processes within an idealized model–observational framework is examined. In an effort to more rigorously constrain ice growth processes (e.g., vapor deposition) with observations of natural clouds, a novel framework is developed to compare simulated and observed radar measurements, coupling a bulk adaptive-habit model of vapor growth to a polarimetric radar forward model. Bayesian inference on key microphysical model parameters is then used, via a Markov chain Monte Carlo sampler, to estimate the probability distribution of the model parameters. The statistical formalism of this method allows for robust estimates of the optimal parameter values, along with (non-Gaussian) estimates of their uncertainty. To demonstrate this framework, observations from Department of Energy radars in the Arctic during a case of pristine ice precipitation are used to constrain vapor deposition parameters in the adaptive habit model. The resulting parameter probability distributions provide physically plausible changes in ice particle density and aspect ratio during growth. A lack of direct constraint on the number concentration produces a range of possible mean particle sizes, with the mean size inversely correlated to number concentration. Consistency is found between the estimated inherent growth ratio and independent laboratory measurements, increasing confidence in the parameter PDFs and demonstrating the effectiveness of the radar measurements in constraining the parameters. Furthermore, the combined Doppler and polarimetric observations produce the highest-confidence estimates of the parameter PDFs, with the Doppler measurements providing a stronger constraint for this case.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Emissions minimization on road networks via Generic Second Order Models

In this paper we consider the problem of estimating emissions due to vehicular traffic on complex networks, and minimizing their effect by regulating traffic at junctions. For the traffic evolution, we consider a Generic Second Order Model, which encompasses the majority of two-equations (i.e., second-order) models available in the literature, and extend it to road networks with merge and diverge junctions. The dynamics on the whole network is determined by selecting a solution to the Riemann Problems at junctions, i.e., the Cauchy problems with constant initial data on each incident road. The latter are solved by assuming the maximization of the flow and assigning a traffic distribution coefficient for outgoing roads of diverges, and a priority rule for incoming roads of merges. A general emission model is considered and its parameters are tuned to the $ {\mathrm{NO_{x}}} $ emission rate. The minimization of emissions is then formulated in terms of the traffic distribution and priority parameters, taking into account travel times. A comparison is provided between roundabouts with optimized parameters and traffic lights, which correspond to time-varying traffic priorities. Our approach can be adapted to manage traffic in complex networks in order to reduce emissions while keeping travel time at acceptable levels.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

Improved optical standing-wave beam splitters for dilute Bose–Einstein condensates

Bose–Einstein condensate (BEC)-based atom interferometry exploits low temperatures and long coherence lengths to facilitate high-precision measurements. Progress in atom interferometry promises improvements in navigational devices like gyroscopes and accelerometers, as well as applications in fundamental physics such as accurate determination of physical constants. Previous work demonstrates that beam splitters and mirrors for coherent manipulation of dilute BEC momentum in atom interferometers can be implemented with sequences of non-resonant standing-wave light pulses. While previous work focuses on the optimization of the optical pulses’ amplitude and duration to produce high-order momentum states with high fidelity, we explore how varying the shape of the optical pulses affects optimal beam-splitter performance, as well as the effect of pulse shape on the sensitivity of optimized parameters in achieving high fidelity in high-momentum states. Here, in simulations of two-pulse beam splitters utilizing optimized square, triangle, and sinc-squared pulse shapes applied to dilute BECs, we, in some cases, reduce parameter sensitivity by an order of magnitude while maintaining fidelity.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2022

Modernization efforts for the R -Matrix code SAMMY [Abstract]

The R-Matrix code SAMMY is a widely used nuclear data evaluation code focused on the resolved range, which includes corrections for experimental effects. The code is still mostly written in Fortran 77, and uses a memory management system suitable for the time of its initial writing (1984). A modernization effort is under way to bring the code in-line with modern software development practices. A continuous-integration testing framework was added, automating the large existing set of test cases. It is run on every commit. The memory management was updated to current standard practices suitable for modern software analysis tools. The code can be obtained from https://code.ornl.gov/RNSD/SAMMY. The resonance parameters and covariance information are now stored in C++ objects shared by SAMMY and AMPX, the processing code that generates nuclear data libraries for SCALE. This allows for easier maintenance and access to the resonance parameters inside and outside of SAMMY. This feature is already used by accessing and changing parameters in memory in the Bayesian Monte Carlo Evaluation Framework for Cross Sections Nuclear Data and Integral Benchmark Experiments project, Further plans include the switch to the ENDF reading and writing routines in AMPX, as these routines are more robust, easier to maintain, and support more features. Of note here is support for the new GNDS format. Previously it wasn’t easy to share the full covariance matrix for evaluations containing more than one isotope due to limitations on the ENDF format; this is now supported in GNDS. The data are currently available in a binary SAMMY format and can be exported to GNDS to make them more widely available and sharable. The next step will be to use the same resonance processing code at 0K in AMPX and SAMMY as one of the available Reich-Moore R-Matrix formalism. The first step toward this goal is to isolate the reconstruction into a module that takes resonance parameters as its input and does not depend on SAMMY global parameters. This goal has been achieved and it should now be possible to more easily change the resonance formalism and add enhancements as the Phenomenological R-Matrix parameterization of direct, doorway, and compound nuclear reactions discussed elsewhere on this conference. This concerted modernization and enhancement effort provides multiple advantages to the nuclear data community. It will allow parameter optimization using enhanced formalisms, including experimental effects, that better match complex experimental data. Then those evaluated parameters can immediately be passed off to AMPX to be reconstructed with the exact same cross section model and be put into a data library for subsequent testing using SCALE and the Valid Benchmark suite or other suitable benchmark suites.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗