Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Noise Reduction Potential of Phase Control for Distributed Propulsion Vehicles

Phase control is a noise reduction technique leveraging destructive interference of the coherent acoustic source field between a system of propellers rotating at equivalent rates. Carefully selecting the relative azimuthal blade positions (phase), the overall directivity of the blade passage frequency noise can be modified, potentially steering these tonal components away from sensitive areas. A modeling technique is described and validated using measurements of a dual-rotor system. The sensitivity of noise reduction through phase control is studied in a typical parameter space, i.e., dependence on rotation rate, number of propellers, spacing and layout, and rotation direction. Additionally, estimates of how realistic conditions, e.g., error in the phase controller, degrade potential benefits are described based on the generalized coherence of the system. From this, it is observed that the deviation from the nominal rotation rate should not exceed approximately 0.5% to achieve a 6 dB decrease at the blade passage frequency.

Kyle A Pascioni↗
NASA NTRS1982

Synthesis of offset dual reflector antennas transforming a given feed illumination pattern into a specified aperture distribution

The problem of transforming a given primary feed pattern into a desired aperture field distribution through two reflections by an offset dual reflector system is investigated using the concepts of geometrical optics. A numerically rigorous solution for the reflector surfaces is developed which realizes an exact aperture phase distribution and an aperture amplitude distribution that is accurate to within an arbitrarily small numerical tolerance. However, this procedure does not always yield a smooth solution, i.e., the reflector surfaces thus realized may not be continuous or their slopes may vary too rapidly. In the event of nonexistence of a numerically rigorous smooth solution, an approximate solution that enforces the smoothness of the reflector surfaces can be obtained. In the approximate solution, only the requirement for the aperture amplitude distribution is relaxed, and the condition on the aperture phase distribution is continued to be satisfied exactly.

Mittra, R.↗
DOE OSTI2021

In Situ Characterization of Ferroelectric HfO 2 During Rapid Thermal Annealing

Thermal annealing is critical in governing the phase distribution, and ultimately the electrical properties, of ferroelectric hafnium oxide films. In particular, rapid thermal annealing (RTA) has been shown to favor the formation of ferroelectric crystal phases, but the dynamic behavior of the film over the course of the anneal is not well understood. Herein, synchrotron X-ray diffraction is used to characterize the phase distribution of HfO 2 films deposited by atomic layer deposition (ALD) in situ during RTA, revealing complex phase transformations occurring on the scale of seconds. All samples investigated here transform into a nonmonoclinic phase, which is required for ferroelectric films. However, this phase often converts into the more stable monoclinic phase as annealing proceeds. The kinetic barrier to the transformation to the monoclinic phase during heating is higher than 1 eV f.u. -1 In this work, the initial crystallization into the ferroelectric phase and relatively high barrier to transformation to the nonferroelectric phase suggests that careful control of the thermal annealing profile can greatly increase the ferroelectric fraction of the film. By using a fast ramp rate and a short annealing time above the ferroelectric crystallization temperature, the remanent polarization of a pure HfO 2 film can be increased more than twofold.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Angular momentum eigenstates of the isotropic 3-D harmonic oscillator: Phase-space distributions and coalescence probabilities

The isotropic 3-dimensional harmonic oscillator potential can serve as an approximate description of many systems in atomic, solid state, nuclear, and particle physics. In particular, the question of 2 particles binding (or coalescing) into angular momentum eigenstates in such a potential has interesting applications. Here we compute the probabilities for coalescence of two distinguishable, non-relativistic particles into such a bound state, where the initial particles are represented by generic wave packets of given average positions and momenta. We use a phase-space formulation and hence need the Wigner distribution functions of angular momentum eigenstates in isotropic 3-dimensional harmonic oscillators. These distribution functions have been discussed in the literature before but we utilize an alternative approach to obtain these functions. Along the way, we derive a general formula that expands angular momentum eigenstates in terms of products of 1-dimensional harmonic oscillator eigenstates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Probing Dopant Redistribution, Phase Propagation, and Local Chemical Changes in the Synthesis of Layered Oxide Battery Cathodes

Achieving the targeted control of layered oxide properties calls for more fundamental studies to mechanistically probe their evolution during their synthesis. Herein, dopant distribution, phase propagation, and local chemical changes as well as their interplay in multielement-doped LiNiO 2 materials are investigated using spectroscopic, imaging, and scattering techniques. It is shown that dopants undergo dynamic redistribution in the Ni(OH) 2 host lattice at the early stage of calcination (below 300 °C). Such redistribution behavior exhibits strong dopant-dependent characteristics, allowing for targeted surface and bulk doping control. The Ni oxidation process exhibits depth-dependent characteristics and the most rapid Ni oxidation takes place between 300 and 700 °C. Using Ni oxidation state as the proxy for the phase transformation, the buildup of heterogenous phase propagation in the early stage of calcination is shown, especially along the radial direction of secondary particles. Furthermore, the radial heterogenous phase distribution gradually decreases upon completing the calcination. However, a high degree of mosaic-like heterogeneity may still be present in the final product, departing from the perfect layered oxide. Overall, the present study offers fundamental insights into manipulating multiscale materials properties during calcination for obtaining stable, high-energy layered oxide cathodes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electric Vehicles at Scale - Phase II - Distribution Systems Analysis

The use of electric vehicles (EVs) in the United States has grown significantly during the last decade, posing benefits to the environment but also potential challenges to our grid. To better understand this scenario , the Department of Energy (DOE) asked Pacific Northwest National Laboratory (PNNL) to perform an authoritative study of the impacts of EVs at scale on the electric grid. The Phase I study focused on the bulk power electricity impacts . This EV-at-scale Phase II work addresses key questions of interest to DOE related to the impacts of EV in the distribution systems: 1. When (which year), where, and how many EVs will be adopted and how will they be charged? 2. Given some prospective answers to the above question, what would be the EV hosting capability of a distribution system circuit? 3. How could the hosting capability be expanded to accommodate more EVs and what would be the potential measures and cost? This report documents the methodologies developed as part of this project and provides EV adoption modeling examples using distribution system circuit data provided by industry partner, Southern California Edison (SCE).

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1997

Real-Time X-Ray Transmission Microscopy of Solidifying Al-In Alloys

Real-time observations of transparent analog materials have provided insight, yet the results of these observations are not necessarily representative of opaque metallic systems. In order to study the detailed dynamics of the solidification process, we develop the technologies needed for real-time X ray microscopy of solidifying metallic systems, which has not previously been feasible with the necessary resolution, speed, and contrast. In initial studies of Al-In monotectic alloys unidirectionally solidified in an X-ray transparent furnace, in situ records of the evolution of interface morphologies, interfacial solute accumulation, and formation of the monotectic droplets were obtained for the first time: A radiomicrograph of Al-30In grown during aircraft parabolic maneuvers is presented, showing the volumetric phase distribution in this specimen. The benefits of using X-ray microscopy for postsolidification metallography include ease of specimen preparation, increased sensitivity, and three-dimensional analysis of phase distribution. Imaging of the solute boundary layer revealed that the isoconcentration lines are not parallel (as is often assumed) to the growth interface. Striations in the solidified crystal did not accurately decorate the interface position and shape. The monotectic composition alloy under some conditions grew in an uncoupled manner.

Curreri, Peter A.↗
DOE OSTI2024

Solvent-mediated carboxylic acid diammonium spacer for synthesizing FA-based 2D Dion–Jacobson perovskites toward efficient solar cells

Two-dimensional (2D) perovskites are promising for photovoltaic applications due to their outstanding optical properties and better environmental stability compared to three-dimensional (3D) perovskites. Unlike 2D Ruddlesden–Popper (RP) perovskites, which use monovalent ammonium spacers, Dion–Jacobson (DJ) perovskites employ divalent organic spacers that enhance structural stability by mitigating weak van der Waals interactions. However, the random phase distribution and disorder crystal orientation in 2D DJ perovskites create deep quantum wells, hindering charge transfer and reducing short-circuit current density (J SC ) and overall photovoltaic performance. This study introduces an organic diammonium, 1,4-butanediamine diacetate (BDAAc 2 ), to replace the traditional halide spacer 1,4-butanediamine iodide (BDADI 2 ). This substitution regulates perovskites crystallization dynamics, reducing compositional disorder and random phase distribution, thus improving the quality of the perovskite films. The robust coordination interactions between BDAAc 2 and the perovskite inorganic framework lead to an ordered [PbX 6 ] 4− arrangement, suppressing the formation of complex intermediate phases and significantly enhancing δ phase crystallinity in the intermediate film. This results in a high yield of high-quality α phase. Consequently, the resulting 2D DJ perovskite solar cells based on BDAFA 3 Pb 4 (I 0.9 Br 0.1 ) 13 achieve a higher power conversion efficiency of 16.41% and an elevated J SC of 20.46 mA cm −2 .

14 SOLAR ENERGY↗
DOE OSTI2021

Lattice Boltzmann Modeling of Drying of Porous Media Considering Contact Angle Hysteresis

Drying of porous media is governed by a combination of evaporation and movement of the liquid phase within the porous structure. Contact angle hysteresis induced by surface roughness is shown to influence multi-phase flows, such as contact line motion of droplet, phase distribution during drainage and coffee ring formed after droplet drying in constant contact radius mode. However, the influence of contact angle hysteresis on liquid drying in porous media is still an unanswered question. Lattice Boltzmann model (LBM) is an advanced numerical approach increasingly used to study phase change problems including drying. In this paper, based on a geometric formulation scheme to prescribe contact angle, we implement a contact angle hysteresis model within the framework of a two-phase pseudopotential LBM. The capability and accuracy of prescribing and automatically measuring contact angles over a large range are tested and validated by simulating droplets sitting on flat and curved surfaces. Afterward, the proposed contact angle hysteresis model is validated by modeling droplet drying on flat and curved surfaces. Then, drying of two connected capillary tubes is studied, considering the influence of different contact angle hysteresis ranges on drying dynamics. Finally, the model is applied to study drying of a dual-porosity porous medium, where phase distribution and drying rate are compared with and without contact angle hysteresis. The proposed model is shown to be capable of dealing with different contact angle hysteresis ranges accurately and of capturing the physical mechanisms during drying in different porous media including flat and curved geometries.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Solar cycle signal in air temperature in North America - Amplitude, gradient, phase and distribution

The considered investigation was motivated by three factors. One is related to an extension of single-channel MESA to multi-channel by Strand (1977), Morf et al. (1978), and Jones (1978). MESA is a high-resolution signal processing and spectrum analysis technique due to Burg (1975). The considered developments resulted in the discovery of the 11-year solar cycle signal in the change of the length of day by Currie (1980, 1981). They also led Currie (1981) to study the phase spectrum of the 11-year term in height H of sea level. The investigation tries to clarify the phase relations among the involved parameters. The second factor is connected with an application of the linear time domain technique used by Currie (1981) to temperature records to obtain more accurate information regarding the signal amplitude. The third factor of motivation is related to increases in the number of stations available for an analysis, the greater average length of the records, and the more accurate data set.

Currie, R. G.↗
DOE OSTI2025

Nanotomography for Quantitative 3D Particle Reconstruction

Particulates are ubiquitous across fuel cycle operations and carry critical information about particle formation, processing, and potential proliferation-related activities. Traditional analytical techniques, including micro-Raman spectroscopy and standard electron microscopy, are often limited in spatial resolution or dimensionality, particularly when used to examine metallic or submicron-scale features. Understanding particle morphology, phase distribution, and internal porosity is essential for constraining formation conditions, thermodynamic environments, and material transport behavior. In this report, we demonstrate the application of plasma focused ion beam nanotomography to reconstruct micron-scale particulates at nanoscale resolution. Using high-resolution backscattered electron imaging and Avizo software, we obtained 3D reconstructions that enabled quantitative analysis of particle morphology, phase composition, and internal voids. Representative examples include a Ta particle with a large central void and a composite particle with embedded tetrahedral crystalline structures. These reconstructions reveal structural and compositional details that are inaccessible through conventional 2D imaging. The results demonstrate that nanotomography provides both qualitative and quantitative insights into particle formation and behavior. Using nanotomography, porosity and phase distributions can be quantified to inform models of particle density, transport, and solidification conditions. Beyond technical insights, the workflow developed here establishes a transferable capability for analyzing heterogeneous particles and has potential applications in bulk materials studies via x-ray computed tomography or other volumetric imaging modalities. Ongoing efforts are focused on optimizing the workflow to process multiple particles simultaneously, increasing throughput and statistical robustness. Overall, this work illustrates the power of nanotomography as a tool for connecting particulate morphology to formation mechanisms, composition, and transport, thereby strengthening analytical capabilities for nuclear forensics, fuel cycle analysis, and related scientific investigations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Improved single-particle phase-space distributions for viscous fluid dynamic models of relativistic heavy ion collisions

Comparison of hydrodynamic calculations with experimental data inevitably requires a model for converting the fluid to particles. For shear viscous fluids, several different conversion models have been proposed, such as the quadratic Grad corrections, the Strickland-Romatschke (SR) ansatz, self-consistent shear corrections from linearized kinetic theory, or corrections from the relaxation time approach. We show, via comparison to nonlinear 2 → 2 kinetic theory evolution, that even for low specific shear viscosities 0.03 ≲ $\textit{η/s}$ ≲ 0.2 , these four models have varying accuracy and still significant errors in reproducing particle phase space densities from hydrodynamic fields. Moreover, we demonstrate that the overall reconstruction error of additive shear viscous $f = f_{eq} + δf$ models dramatically reduces by up to one order of magnitude, if one ensures through exponentiation that $\textit{f}$ is always positive. Further, we also illustrate how even more accurate viscous $\textit{δf}$ models can be constructed by incorporating the first time derivatives of hydrodynamic fields to account for the past evolution of the system. Such time derivatives are readily available in hydrodynamic simulations, though usually not included in the output. Though our comparisons are limited to a one-component massless system undergoing a (0 + 1)-dimensional (0 + 1D) longitudinal boost-invariant expansion, we expect that the improved models will be useful in 2 + 1D and 3 + 1D hydrodynamic studies as well.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1988

Distributed Architecture For Phased-Array Antennas

Distributed Architecture for Phased Array Antennas (DISTAR) computer program simulation tool used to study implementation of distributed phased-array equipment. Allows placement of possibly-faulty transmitting/receiving modules at locations throughout array. Variations in amplifiers and phase shifters degrades performance of antenna, depending on environmental conditions and array architecture. Enables antenna designer to examine characteristics of array and how they affect both types and extents of antenna failures. General specifications for amplifier and phase-shifter tolerances determined for various architectures. Written in FORTRAN 77.

Davidson, Shayla E.↗
NASA NTRS1980

Acoustic pressures on a prop-fan aircraft fuselage surface

Acoustic pressure amplitude and phase distributions on the surface of a simulated fuselage (a rigid semi-cylinder) installed in an acoustically treated wind tunnel near a Prop-Fan model were measured. The test conditions simulated the relative tip Mach number and blade loading of a full scale Prop-Fan at high altitude 0.8 Mach number cruise. Measurements were also made at equivalent microphone locations without the semi-cylinder to establish the effects of the presence of a fuselage on the sound pressure amplitudes. These effects were found to be 6 dB at 90 degrees incidence, decreasing to no effect at grazing incidence. Comparison of measurements and calculations using a Hamilton Standard Prop-Fan noise calculation computer program showed good agreement in peak level and in phase distribution. Continuous recordings were also made of a Prop-Fan RPM sweep at constant simulated flight speed and a simulated flight speed sweep at constant Prop-Fan RPM. These showed smooth variations in noise level over the tip Mach number range 0.878 to 1.143.

Magliozzi, B.↗
DOE OSTI2018

On the reinforcement homogenization in CNT/metal matrix composites during severe plastic deformation

Highlights: • Carbon nanotube-reinforced composites were processed by severe plastic deformation. • The evolution of the second phase distribution homogeneity is thoroughly analyzed. • The analysis is carried out with increasing equivalent strains. • A combination of two methods is applied and discussed. • A model that predicts the equivalent strain necessary for homogeneity is proposed. - Abstract: Carbon nanotube (CNT)-reinforced nickel matrix composites with different concentrations were processed by high pressure torsion (HPT). We thoroughly characterized the CNT agglomerates' spatial arrangement at different stages of deformation in order to extract information valuable for the optimization of the processing parameters and to elucidate the mechanisms involved during the processing of particle reinforced metal matrix composites by HPT. From the electron micrographs taken on the radial direction with increasing equivalent strains, we observed that CNT agglomerates debond by relative sliding between CNT during HPT, becoming spherical at higher stages of deformation. Furthermore, we introduced a model for the prediction of the minimum strain required for a homogeneous distribution of a second phase during HPT, which can be correlated to the material's three-dimensional structure and agrees well with the experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Numerical analysis of experimental studies of methane hydrate dissociation induced by depressurization in a sandy porous medium

Methane Hydrates (MHs) are a promising energy source abundantly available in nature. Understanding the complex processes of MH formation and dissociation is critical for the development of safe and efficient technologies for energy recovery. Many laboratory and numerical studies have investigated these processes using synthesized MH-bearing sediments. A near-universal issue encountered in these studies is the spatial heterogeneous hydrate distribution in the testing apparatus. In the absence of direct observations (e.g. using X-ray computed tomography) coupled with real time production data, the common assumption made in almost all numerical studies is a homogeneous distribution of the various phases. In an earlier study (Yin et al., 2018) that involved the numerical description of a set of experiments on MH-formation in sandy medium using the excess water method, we showed that spatially heterogeneous phase distribution is inevitable and significant. In the present study, we use as a starting point the results and observations at the end of the MH formation and seek to numerically reproduce the laboratory experiments of depressurization-induced dissociation of the spatially-heterogeneous MH distribution. This numerical study faithfully reproduces the geometry of the laboratory apparatus, the initial and boundary conditions of the system, and the parameters of the dissociation stimulus, capturing accurately all stages of the experimental process. Using inverse modelling (history-matching) that minimized deviations between the experimental observations and numerical predictions, we determined the values of all the important flow, thermal, and kinetic parameters that control the system behaviour, which yielded simulation results that were in excellent agreement with the measurements of key monitored variables, i.e. pressure, temperature, cumulative production of gas and water over time. We determined that at the onset of depressurization (when the pressure drop – the driving force of dissociation – is at its maximum), the rate of MH dissociation approaches that of an equilibrium reaction and is limited by the heat transfer from the system surroundings. Furthermore, as the effect of depressurization declines over time, the dissociation reaction becomes kinetically limited despite significant heat inflows from the boundaries, which lead to localized temperature increases in the reactor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗