SEARCH · Search NASA

Results for “Plasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Paper or Plastic? Multiscale Material Handling Properties of Two Model Municipal Solid Waste Streams

Purpose: Municipal Solid Waste (MSW) is a potentially valuable sustainable feedstock for fuel and chemical production due to its carbon-rich content and low cost. This study aims to assess the material handling properties of paperand plastic-rich MSW feedstocks to mitigate equipment failure and processing downtime. Methods: The material handling properties of crumbled MSW feedstocks were measured using apowder rheometer with mass flow hopper calculations to assess handling performance. Inverse gas chromatography was use to measure the surface energy differences between feedstocks. Electron microscopy and Raman spectroscopy was used to evaluate microscale features that may contribute to material handling differences. Results: Plastic and paper rich feedstocks crumbled to a nominal 2 mm particle size were observed to have similar flow and handling characteristics with reasonable hopper outlets. 2 mm plastic rich crumbles, with their higher bulk density, exhibited superior flow performance. By contrast, 4 mm material required significantly larger hopper outlets, indicating poor flowability. Paper rich and 4 mm plastic rich samples displayed broad particle size distributions, which contributed to particle interlocking, jamming, and other flow issues. Electron microscopy revealed that plastic rich samples were significantly smoother, enhancing their flowability compared to the rougher, paper rich materials. Conclusions: This study establishes critical material handling baselines for processing MSW as a viable feedstock for fuel and chemical production. The findings highlight the importance of optimizing particle size and feedstock composition to improve flowability and handling performance.

09 BIOMASS FUELS↗

DOE OSTI2024

Microwave-assisted catalytic gasification of mixed plastics and corn stover for low tar, hydrogen-rich syngas production

The challenge for efficient management of post-consumer plastic and biomass waste has grown over the past few decades due to their dramatic increases. In comparison to conventional gasification, microwave-assisted co-gasification of plastics and corn stover offers many benefits, including increased H 2 yield and gas components compared to unfavorable char/tar. Nonetheless, for future commercialization of the process and ease of product separation, further reduction of the undesirable tar is necessary, which can be achieved over the catalytic route. Here, in this work, we studied the catalytic effect of magnetite for microwave-assisted co-gasification of corn stover and plastic to make syngas with higher H 2 and lower tar selectivity over non-catalytic conditions. A 1:1:1 ratio of plastic-corn stover-magnetite was used to evaluate the reaction parameters such as temperature, space velocity, heating media, and catalytic cycles under gasification conditions. In comparison with the microwave non-catalytic route, a 100% increase in the total H 2 yield with 76% higher H 2 production efficiency (mmol/kWh) was achieved in the presence of the magnetite catalyst, while reducing the overall tar formation from 9% to 2%. When magnetite was reduced in situ during the reaction, it coupled with microwave and delivered oxygen radicals that cracked down plastic and corn stover intermediates generated from the synergistic effect under microwave heating. Soon after the oxygen transfer process initiated, magnetite reached its final oxidation state consisting of microwave-active Fe and Fe 3 C phases that continued coupling with microwaves along with the generated graphitic carbon to maintain the heat necessary to further reduce the generated tar and make additional gaseous products, as confirmed by XRD, Raman, and TGA analyses.

08 HYDROGEN↗

DOE OSTI2024

Modeling plasticity-mediated void growth at the single crystal scale: A physics-informed machine learning approach

Modeling the evolution of voids during plastic flow as well as their effects on plastic dissipation is critical for both component manufacturing and lifetime estimation purposes. To this end, we propose a rate-dependent constitutive model to homogenize the effects of semi-randomly distributed voids on single crystal plasticity whilst capturing void interaction and plastic anisotropy. Here, this present work focuses on the case of face centered cubic crystals to introduce an anisotropic gauge function applicable within the crystal plasticity formalism. The approach combines analytical methods to describe the micromechanics of the system in combination with symbolic regression to capture analytically intractable mechanisms from data. The hybrid framework uses a physics-informed genetic programming-based symbolic regression algorithm to solve a multiform optimization problem simultaneously producing a new gauge function and a new strain rate equation. This is also a multi-objective optimization problem with many competing objectives. A new search and selection step is introduced to the genetic algorithm that promotes convergence toward a global solution that better satisfies all the objectives. Overall, the symbolic equations produced leverage data-driven methods to achieve greater accuracy than comparable alternatives on an analytically intractable problem while maintaining model transparency.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Ion Transport and Crystal Rotation in Plastic Crystal Electrolytes Under Applied Electric Fields

Organic ionic plastic crystal electrolytes, containing a plastic crystal and lithium salt, offer a potential balance between mechanical and electrochemical properties for solid state lithium-ion battery electrolytes. These electrolytes contain multiple mobile ionic species (three or four), resulting in complex transport mechanisms which have not yet been established. Plastic crystals are defined by long-range positional order and short-range rotational disorder. It is therefore necessary to quantify changes in the local crystal structure of the electrolyte as current flows through it. Herein, we examine the electrochemical properties of pyrrolidinium-based plastic crystal electrolytes containing lithium salt and zwitterion additives, including measurements of current fraction and limiting current. We obtain species-specific insight into electrolyte transport using pulsed-field gradient nuclear magnetic resonance spectroscopy and find that, while the zwitterion additive increases ionic conductivity, it decreases lithium diffusivity with respect to other ionic components. With operando spatiotemporally resolved wide-angle X-ray scattering we observe location-specific crystal rotations due to the passage of ionic current. In conclusion, we posit that reducing energy dissipation due to rotation is essential for using plastic crystal electrolytes in practical applications.

Yap, Kyra M. K. [University of California, Berkele↗

DOE OSTI2025

Solvent-based plastic recycling technologies

Solvent-based recycling approaches are receiving industrial and academic interest for their ability to produce high-quality plastic resins from a variety of plastic waste sources without breaking the polymer chains. Here we highlight the development of solvent-based technologies, focusing on the underlying principles, techno-economic and life-cycle analyses, and commercialization. The basic steps in solvent-based recycling include plastic size reduction, plastic dissolution, filtration or centrifugation, and optional additional cleaning steps such as adsorption, precipitation and solvent removal. Impurities that build up in the solvent must also be removed. The goal of solvent-based technologies is to produce a high-quality resin without plastic contaminants or other added substances. Disadvantages of these solvent-based technologies are their physicochemical complexity and the difficulty in scaling up to achieve continuous operations with high polymer and solvent yields and throughputs. As a result, chemical engineering is thus critical in bringing solvent-based recycling technologies to market.

Chemical engineering↗

DOE OSTI2025

RB-TnSeq elucidates dicarboxylic-acid-specific catabolism in β-proteobacteria for improved plastic monomer upcycling

Dicarboxylic acids are key components of many polymers and plastics, making them a target for both engineered microbial degradation and sustainable bioproduction. In this study, we generated a comprehensive data set of functional evidence for the genetic basis of dicarboxylic and fatty acid metabolism using randomly barcoded transposon sequencing (RB-TnSeq). We identified four β-proteobacteria that displayed robust growth with dicarboxylic acid sole carbon source and cultured their mutant libraries with dicarboxylic and fatty acids with carbon chain lengths from C3 to C12. The resulting fitness data suggested that dicarboxylic and fatty acid metabolisms are largely distinct, and different sets of β-oxidation genes are required for catabolizing dicarboxylic versus fatty acids of the same carbon chain lengths. In addition, we identified transcriptional regulators and transporters with strong fitness phenotypes related to dicarboxylic acid utilization. In Ralstonia sp. UNC404CL21Col (R. CL21), we deleted two transcriptional repressors to improve its utilization of short-chain dicarboxylic acids. We exploited the diacid-utilizing catabolism of R. CL21 to upcycle a mock mixture of the dicarboxylic acids produced when polyethylene is oxidized. After introducing a heterologous indigoidine production pathway, this engineered Ralstonia produced 0.56 ± 0.02 g/L indigoidine from a mixture of dicarboxylic acids as a carbon source, demonstrating the potential of R. CL21 to upcycle plastic wastes to products derived from tricarboxylic acid (TCA) cycle intermediates. IMPORTANCE: Upcycling the carbon in plastic wastes to value-added products is a promising approach to address the plastic waste and climate crises, and dicarboxylic acid metabolism is an important facet of several approaches. Improving our understanding of the genetic basis of this metabolism has the potential to uncover new enzymes and genetic parts for engineered pathways involving dicarboxylic acids. Our data set is the most comprehensive interrogation of dicarboxylic acid catabolism to date, and this work will be of utility to researchers interested in both plastics bioproduction and upcycling applications.

Pearson, Allison N↗

DOE OSTI2024

Co-gasification of Plastic, Coal Waste and Biomass for Hydrogen Rich Syngas Production

Plastic waste has increasingly become one of the most pressing environmental issues. To mitigate plastic emissions, extraordinary efforts are needed for plastic waste recycling and management. This study investigates the co-gasification of plastic, coal refuse, and biomass into hydrogen-rich syngas through steam gasification. The study focuses on the correlations between process parameters and feedstock composition. Coal refuse and biomass are used as co-feedstocks for gasification, aiming to improve the handling of plastic waste and investigating their synergistic effects on product distribution.

Bashir, Muhammad↗

DOE OSTI2025

Chemical Recycling of Plastic Waste to Higher Value Lubricants

The aim of this project was to develop scalable methods to convert plastic waste to petrochemical-equivalent feedstocks and demonstrate their utility in lubricant base oil and wax applications. These objectives were partially accomplished, by scaling up the synthesis of platinum-on-strontium titanate catalysts to twenty gram batches, scaling up the conversion of plastic waste to twenty-five grams of plastic, producing high-melt waxes and characterizing their properties, and demonstrating the purification of high-melt waxes. High-melt waxes are one petrochemical-equivalent feedstock that can be made from plastic waste, consisting of a hard wax with a melt point above 65 C. They are used as ingredients in hot melt adhesives, coatings, and cosmetics. Producing a petrochemical-equivalent feedstock from plastic waste provides an advantage in lower carbon footprint and manufacturing cost, as the waste feedstock costs less than crude oil.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1982

Elastic-plastic finite-element analyses of thermally cycled single-edge wedge specimens

Elastic-plastic stress-strain analyses were performed for single-edge wedge alloys subjected to thermal cycling in fluidized beds. Three cases (NASA TAZ-8A alloy under one cycling condition and 316 stainless steel alloy under two cycling conditions) were analyzed by using the MARC nonlinear, finite-element computer program. Elastic solutions from MARC showed good agreement with previously reported solutions that used the NASTRAN and ISO3DQ computer programs. The NASA TAZ-8A case exhibited no plastic strains, and the elastic and elastic-plastic analyses gave identical results. Elastic-plastic analyses of the 316 stainless steel alloy showed plastic strain reversal with a shift of the mean stresses in the compressive direction. The maximum equivalent total strain ranges for these cases were 13 to 22 percent greater than that calculated from elastic analyses.

Kaufman, A.↗

NASA NTRS1982

On finite deformation elasto-plasticity

Lee (1969) has proposed a theory based on the decomposition of the total deformation gradient to an elastic and plastic part, and from it has concluded that the additive decomposition of the strain rates holds only approximately. Lubarda and Lee (1981) have declared that Lee's 'exact finite-deformation kinematics shows the almost universal assumption that the total velocity strain or rate of deformation is the sum of elastic and plastic rates to be in error'. Hence questions are raised regarding the validity of essentially all finite deformation elasto-plasticity theories. The present investigation is concerned with these questions. It is shown that the additive decomposition of the strain rates follows from all common finite elasto-plasticity concepts. Lee's theory is examined, and it is shown that this theory also leads to an additive strain rate decomposition, and therefore, his conclusion stems from misinterpretation. It is found that the elastic and the plastic strain rates considered by Lee do not correspond to the same configuration. They are, therefore, not compatible measures.

Nemat-Nasser, S.↗

NASA NTRS1983

Implementation of elastic-plastic structural analysis into NASTRAN

Elastic-plastic analytic capabilities were incorporated into the NASTRAN program. The present implementation includes a general rigid format and additional bulk data cards as well as to two new modules. The modules are specialized to include only perfect plasticity of the CTRMEN and CROD elements but can easily be expanded to include other plasticity theories and elements. The practical problem of an elastic-plastic analysis of a ship's bracket connection is demonstrated and compared to an equivalent analysis using Grumman's PLANS program. The present work demonstrates the feasibility of incorporating general elastic-plastic capabilities into NASTRAN.

Levy, A.↗

NASA NTRS1986

The plastic compressibility of 7075-T651 aluminum-alloy plate

The change in volume, and therefore the change in mass density, of an aluminum alloy was measured in uniaxial tension using clip-on extensometers. The experimental data do not agree with the assumption of plastic incompressibility found in the classical theories of plasticity. In fact, the elastic and plastic volume changes are of the same order of magnitude. Plastic anisotropy is thought to be the prime cause of this plastic compressibility.

Freed, A. D.↗

NASA NTRS1990

Finite element elastic-plastic-creep and cyclic life analysis of a cowl lip

Results are presented of elastic, elastic-plastic, and elastic-plastic-creep analyses of a test-rig component of an actively cooled cowl lip. A cowl lip is part of the leading edge of an engine inlet of proposed hypersonic aircraft and is subject to severe thermal loadings and gradients during flight. Values of stresses calculated by elastic analysis are well above the yield strength of the cowl lip material. Such values are highly unrealistic, and thus elastic stress analyses are inappropriate. The inelastic (elastic-plastic and elastic-plastic-creep) analyses produce more reasonable and acceptable stress and strain distributions in the component. Finally, using the results from these analyses, predictions are made for the cyclic crack initiation life of a cowl lip. A comparison of predicted cyclic lives shows the cyclic life prediction from the elastic-plastic-creep analysis to be the lowest and, hence, most realistic.

Arya, Vinod K.↗

NASA NTRS1991

Finite element elastic-plastic-creep and cyclic life analysis of a cowl lip

Results are presented of elastic, elastic-plastic and elastic-plastic-creep analyses of a test-rig component of an actively cooled cowl lip. A cowl lip is part of the leading edge of an engine inlet of proposed hypersonic aircraft and is subject to severe thermal loadings and gradients during flight. Values of stresses calculated by elastic analysis are well above the yield strength of the cowl lip material. Such values are highly unrealistic, and thus elastic stress analyses are inappropriate. The inelastic (elastic-plastic and elastic-plastic-creep) analyses produce more reasonable and acceptable stress and strain distributions in the component. Finally, using the results from these analyses, predictions are made for the cyclic crack initiation life of a cowl lip. A comparison of predicted cyclic lives shows the cyclic life prediction from the elastic-plastic-creep analysis to be the lowest and, hence, most realistic.

Arya, V. K.↗

NASA NTRS1990

Nonlinear analysis of AS4/PEEK thermoplastic composite laminate using a one parameter plasticity model

A one-parameter plasticity model was shown to adequately describe the orthotropic plastic deformation of AS4/PEEK (APC-2) unidirectional thermoplastic composite. This model was verified further for unidirectional and laminated composite panels with and without a hole. The nonlinear stress-strain relations were measured and compared with those predicted by the finite element analysis using the one-parameter elastic-plastic constitutive model. The results show that the one-parameter orthotropic plasticity model is suitable for the analysis of elastic-plastic deformation of AS4/PEEK composite laminates.

Sun, C. T.↗

NASA NTRS1992

Inelastic deformation of metal matrix composites: Plasticity and damage mechanisms, part 2

The inelastic deformation mechanisms for the SiC (SCS-6)/Ti-15-3 system were studied at 538 C (1000 F) using a combination of mechanical measurements and detailed microstructural examinations. The objectives were to evaluate the contributions of plasticity and damage to the overall MMC response, and to compare the room temperature and elevated temperature deformation behaviors. Four different laminates were studied: (0)8, (90)8,(+ or -45)2s, and (0/90)2s, with the primary emphasis on the unidirectional (0)8, and (90)8 systems. The elevated temperature responses were similar to those at room temperature, involving a two-stage elastic-plastic type of response for the (0)8 system, and a characteristic three-stage deformation response for the (90)8 and (+ or -45)2s systems. The primary effects of elevated temperatures included: (1) reduction in the 'yield' and failure strengths; (2) plasticity through diffused slip rather than concentrated planar slip (which occurred at room temperature); and (3) time-dependent deformation. The inelastic deformation mechanism for the (0)8 MMC was dominated by plasticity at both temperatures. For the (90)8 and (+ or -45)2s MMCs, a combination of damage and plasticity contributed to the deformation at both temperatures.

Majumdar, B. S.↗

NASA NTRS1999

Measurement of Plastic Stress and Strain for Analytical Method Verification (MSFC Center Director's Discretionary Fund Project No. 93-08)

The analytical prediction of stress, strain, and fatigue life at locations experiencing local plasticity is full of uncertainties. Much of this uncertainty arises from the material models and their use in the numerical techniques used to solve plasticity problems. Experimental measurements of actual plastic strains would allow the validity of these models and solutions to be tested. This memorandum describes how experimental plastic residual strain measurements were used to verify the results of a thermally induced plastic fatigue failure analysis of a space shuttle main engine fuel pump component.

Price, J. M.↗

NASA NTRS2003

Development of a Fatigue Crack Growth Coupon for Highly Plastic Stress Conditions

This paper presents an analytical approach used to develop a novel fatigue crack growth coupon for a highly plastic 3-D stress field condition. The flight hardware investigated in this paper is a large separation bolt that fractures using pyrotechnics at the appointed time during the flight sequence. The separation bolt has a deep notch that produces a severe stress concentration and a large plastic zone when highly loaded. For this geometry, linear-elastic fracture mechanics (LEFM) techniques are not valid due to the large nonlinear stress field. Unfortunately, industry codes that are generally available for fracture mechanics analysis and fatigue crack growth (e.g. NASGRO (11) are limited to LEFM and are available for only a limited number of geometries. The results of LEFM based codes are questionable when used on geometries with significant plasticity. Therefore elastic-plastic fracture mechanics (EPFM) techniques using the finite element method (FEM) were used to analyze the bolt and test coupons. scale flight hardware is very costly in t e r n of assets, laboratory resources, and schedule. Therefore to alleviate some of these problems, a series of novel test coupons were developed to simulate the elastic-plastic stress field present in the bolt.

Allen, Phillip A.↗