Search NASASearch

SEARCH · Search NASA

Results for “Process Automation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Gain Scheduling for the Orion Launch Abort Vehicle Controller

One of NASAs challenges for the Orion vehicle is the control system design for the Launch Abort Vehicle (LAV), which is required to abort safely at any time during the atmospheric ascent portion of ight. The focus of this paper is the gain design and scheduling process for a controller that covers the wide range of vehicle configurations and flight conditions experienced during the full envelope of potential abort trajectories from the pad to exo-atmospheric flight. Several factors are taken into account in the automation process for tuning the gains including the abort effectors, the environmental changes and the autopilot modes. Gain scheduling is accomplished using a linear quadratic regulator (LQR) approach for the decoupled, simplified linear model throughout the operational envelope in time, altitude and Mach number. The derived gains are then implemented into the full linear model for controller requirement validation. Finally, the gains are tested and evaluated in a non-linear simulation using the vehicles ight software to ensure performance requirements are met. An overview of the LAV controller design and a description of the linear plant models are presented. Examples of the most significant challenges with the automation of the gain tuning process are then discussed. In conclusion, the paper will consider the lessons learned through out the process, especially in regards to automation, and examine the usefulness of the gain scheduling tool and process developed as applicable to non-Orion vehicles.

McNamara, Sara J.

Eye Safe, Visible Wavelength Lidar Systems: Design and Operational Advances, Results and Potential

In the early nineties the first of the eye safe visible wavelength lidar systems known now as Micro Pulse Lidar (MPL) became operational. The important advance of the design was a system that, unlike most existing lidar, operated at eye safe energy densities and could thus operate unattended for full time monitoring. Since that time there have been many dozens of these systems produced and applied for full time profiling of atmospheric cloud and aerosol structure. There is currently an observational network of MPL sites to support global climate research. In thc course of application of these instruments there have been significant improvements in the, design and performance of the systems. In the last half decade particularly there has been significant application and technical development of MPL systems. In this paper we review progress. The current MPL systems in use are all single wavelength systems designed for cloud and aerosol applications. For the cloud and aerosol applications, both lidar depolarization and multi wavelength measurements have significant applications. These can be accomplished with the MPL, approach. The main current challenge for the lidar network activity are in the area of the reliability, repeatability and efficiency of data processing. The network makes use of internet data downloads and automated processing. The heights of all cloud and aerosol layers are needed. The recent emphasis has been in operationally deriving aerosol extinction cross section. Future emphasis will include adding cirrus optical parameters. For operational effectiveness, improvements to simplify routine data signal calibration are being researched. Overall the MPL systems have proven very effective. A large data base of results from globally distributed sites can be easily accessed through the internet. Applications have included atmospheric model development. Validation of current global satellite observations of aerosol and clouds, including now orbital lidar observations, was a primary goal for NASA. Although sampling issues require careful consideration, results have proven useful.

Spinhirne, James

Automation Bias and Countermeasures in Flight Crews

Results of recent research investigating the use of automated systems have indicated the presence of automation bias, a term describing errors made when decision makers rely on automated cues as a heuristic replacement for vigilant information seeking and processing. Automation commission errors, i.e., errors made when decision makers take inappropriate action because they over-attend to automated information or directives, and automation omission errors, i.e., errors made when decision makers do not take appropriate action because they are not informed of an imminent problem or situation by automated aids, can result from this tendency. In a series of studies, participants who perceived themselves as "accountable" for their strategies of interaction with automation were significantly more likely to verify its correct functioning, and committed significantly fewer automation-related errors than those who did not report this perception. In this study, we focus on two manipulations to encourage verification behaviors within cockpit crews. The first, an information/training manipulation, will focus on explicit information on automation bias, and training for verification of automated functioning. The second manipulation will consist of display prompts to verify automated functioning. Participants (glass-cockpit crews) will fly a series of approaches on the Mini-ACFS, a two-person pan-task flight simulator. Approach scenarios include several automation "events," that is, glitches, malfunctions, or inappropriate recommendations, that can be caught if cross-checked with other cockpit indicators. We anticipate that these manipulations will ameliorate automation bias. Final data analysis will be completed prior to the OSU symposium, and is expected to support the hypotheses that: a) reduced errors are associated with verification behaviors; b) crews will be more likely to verify under training/display conditions than when in the control condition; and c) effects will persist when subjects return for a follow-up exercise 6-9 weeks after their first session. Implications for training and automation design will be discussed.

Mosier, Kathleen, L.

Progress Toward Generation of a Navier-Stokes Database for a Harrier in Ground Effect

The Harrier YAV-8B aircraft is capable of vertical and short-field take-off and landing (V/STOL) by directing its four exhaust nozzles toward the ground, or conventional flight by rotating its nozzles into a horizontal position. The British Royal Air Force and the United States Marine Corps have used this aircraft for more than 30 years to provide a quick reaction time for troop support, and reduce the need for long runways. The success of this powered-lift (PL) vehicle has also prompted the more recent design of the Joint Strike Fighter (JSF). However there are significant safety issues that must be addressed when operating a PL vehicle in close proximity to the ground. Hot Gas Ingestion (HGI) by the inlets can result in a rapid loss of powered lift; and high-speed jet flows along the ground plane can induce low pressures underneath the vehicle, causing a 'suck-down' effect. Under these conditions, departure from controlled flight may occur. Moreover, unsteady ground vortices and jet fountains can affect the aircraft,s controllability and its proximity to ground troops. The viscous, time-dependent flow fields of PL vehicles are difficult to accurately and efficiently predict using Computational Fluid Dynamics (CFD). A number of researchers have used the time-dependent Reynolds-averaged Navier-Stokes (RANS) equations to compute flows for single and multiple jets in a cross-flow. A few have added some geometric complexity to the problem by computing flows for jet-augmented delta wings near a ground plane. Smith et.al. computed for the first time a single RANS solution about a simplified Harrier. This geometry included a fuselage, wing, leading edge root extension (LERX), inlets, and exhaust nozzles. All of these investigations cite two practical problems with computing these flows: 1) the need for improved solution accuracy; and, 2) the need for faster solution methods. We view the need for faster solution methods as key to improving the solution accuracy and making this class of computation more routine. One can hardly refine grids, explore the use of advanced turbulence models, and generate databases when it takes weeks of dedicated computer time for a single solution. Chaderjian, Ahmad, Pandya, and Murman have focused on reducing the time-to-solution for this very difficult and complex problem through process automation and exploitation of parallel computing. They began with the Harrier geometry reported, and added a deflected wing flap and empennage for greater realism. To date more than 80 solutions have been carried out. This paper will describe this process and progress made in reducing the time required to generate a simple longitudinal force and moment database for a Harrier in ground effect. It shows a typical snap-shot from an unsteady streakline animation, where fluid particles are colored by temperature. The ground vortex and a jet-fountain vortex are highlighted. It also shows a similar streakline image, where HGI occurs due to the vehicle in close proximity to the ground. It is show the mean lift coefficient as a function of angle of attack and height. The angle of attack range was 4 deg less than or = alpha less than or = 10 deg with an increment of 1 degree, and the height range was 10 ft less than or = h less than or = 30ft with an increment of 5 feet. This 35 solution database was extended to over 2500 cases using a monotone cubic-spline interpolation procedure. The suck-down effect (reduction of lift near the ground) is highlighted in the figure. The "cushion effect," the conventional reduction of lift as the vehicle moves out of ground effect, is also indicated. All 35 RANS solutions were obtained using 952 Silicon Graphics Origin 2000 and 3000 processors in dedicated mode for one week. Typically, 112 processors were assigned to each case. Some other cases used fewer processors to utilize all available CPUS. The final paper will report on the automation of the solution process, including: grid generation, job monitoring, solution completion criteria, and post processing. Moreover, improvements in parallel efficiency for a dual time-step algorithm for the RANS equations will also be presented. Results will be discussed in detail using unsteady streakline flow visualization to correlate unsteady flow structures with dominant aerodynamic frequencies. The stability derivatives, CL, and CL, will also be presented.

Chaderjian, Neal M.

Automation of Space Processing Applications Shuttle payloads

The Space Processing Applications Program is examining the effect of weightlessness on key industrial materials processes, such as crystal growth, fine-grain casting of metals, and production of unique and ultra-pure glasses. Because of safety and in order to obtain optimum performance, some of these processes lend themselves to automation. Automation can increase the number of potential Space Shuttle flight opportunities and increase the overall productivity of the program. Five automated facility design concepts and overall payload combinations incorporating these facilities are presented.

Crosmer, W. E.

Neural Network and Regression Approximations Used in Aircraft Design

NASA Lewis Research Center's CometBoards Test Bed was used to create regression and neural network models for a High-Speed Civil Transport (HSCT) aircraft. Both approximation models that replaced the actual analysis tool predicted the aircraft response in a trivial computational effort. The models allow engineers to quickly study the effects of design variables on constraint and objective values for a given aircraft configuration. For example, an engineer can change the engine size by 1000 pounds of thrust and quickly see how this change affects all the output values without rerunning the entire simulation. In addition, an engineer can change a constraint and use the approximation models to quickly reoptimize the configuration. Generating the neural network and the regression models is a time-consuming process, but this exercise has to be carried out only once. Furthermore, an automated process can reduce calculations substantially.

Patnaik, Surya N.

Design and Analysis of a Tool for Automated Fiber Placement of Composite Wind Tunnel Blades

For decades, composite wind tunnel blades have been constructed using labor-intensive hand layup processes. Automated Fiber Placement (AFP) is a relatively new technology that has not seen widespread use in manufacturing composite wind tunnel blades. AFP offers the potential for reduced manufacturing time, reduced cost, and improved consistency compared to traditional hand layup procedures. These manufacturing qualities are becoming increasingly important as existing wind tunnel blades are replaced due to impact damage or wear and tear from decades of use. Researchers at the NASA Langley Research Center are currently using the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to investigate the feasibility of AFP for manufacturing composite wind tunnel blades. ISAAC uses manufacturing tools as surfaces on which to place fiber tows. A manufacturing tool was developed for using AFP to build a wind tunnel blade shape. This paper presents the structural design and analysis of this tool, for use with AFP, constructed from high temperature thermoplastics. The tool fabricated by this design process was successfully used for AFP and oven cure of two representative airfoil shaped composite structures.

Brian Mason

Applying Standard Interfaces to a Process-Control Language

A method of applying open-operating-system standard interfaces to the NASA User Interface Language (UIL) has been devised. UIL is a computing language that can be used in monitoring and controlling automated processes: for example, the Timeliner computer program, written in UIL, is a general-purpose software system for monitoring and controlling sequences of automated tasks in a target system. In providing the major elements of connectivity between UIL and the target system, the present method offers advantages over the prior method. Most notably, unlike in the prior method, the software description of the target system can be made independent of the applicable compiler software and need not be linked to the applicable executable compiler image. Also unlike in the prior method, it is not necessary to recompile the source code and relink the source code to a new executable compiler image. Abstraction of the description of the target system to a data file can be defined easily, with intuitive syntax, and knowledge of the source-code language is not needed for the definition.

Berthold, Richard T.

AIRSAR Web-Based Data Processing

The AIRSAR automated, Web-based data processing and distribution system is an integrated, end-to-end synthetic aperture radar (SAR) processing system. Designed to function under limited resources and rigorous demands, AIRSAR eliminates operational errors and provides for paperless archiving. Also, it provides a yearly tune-up of the processor on flight missions, as well as quality assurance with new radar modes and anomalous data compensation. The software fully integrates a Web-based SAR data-user request subsystem, a data processing system to automatically generate co-registered multi-frequency images from both polarimetric and interferometric data collection modes in 80/40/20 MHz bandwidth, an automated verification quality assurance subsystem, and an automatic data distribution system for use in the remote-sensor community. Features include Survey Automation Processing in which the software can automatically generate a quick-look image from an entire 90-GB SAR raw data 32-MB/s tape overnight without operator intervention. Also, the software allows product ordering and distribution via a Web-based user request system. To make AIRSAR more user friendly, it has been designed to let users search by entering the desired mission flight line (Missions Searching), or to search for any mission flight line by entering the desired latitude and longitude (Map Searching). For precision image automation processing, the software generates the products according to each data processing request stored in the database via a Queue management system. Users are able to have automatic generation of coregistered multi-frequency images as the software generates polarimetric and/or interferometric SAR data processing in ground and/or slant projection according to user processing requests for one of the 12 radar modes.

Chu, Anhua

Low-cost Landsat digital processing system for state and local information systems

The paper details a minicomputer-based system which is well within the budget of many state, regional, and local agencies that previously could not afford digital processing capability. In order to achieve this goal a workable small-scale Landsat system is examined to provide low-cost automated processing. It is anticipated that the alternative systems will be based on a single minicomputer, but that the peripherals will vary depending on the capability emphasized in a particular system.

Hooper, N. J.

Feasibility of Additive Manufacturing for Thermal Protection Systems

Thermal Protection Systems (TPS) use advanced materials to protect vehicles from aerodynamic heating during atmospheric entry. Manufacturing of these composite materials is often very time consuming and labor-intensive. Leveraging the additive manufacturing FDM (Fused Deposition Modeling) process enables NASA to design and manufacture advanced ablative TPS materials while reducing manufacturing time and cost. Since additive manufacturing is an automated process, it ensures part consistency over the entire heat shield area. The purpose for this presentation will be three-fold. 1) Introduce novel low-density ablative materials capable of utilizing additive manufacturing capabilities 2) show feasibility of additively manufacturing TPS coupons using the downselected TPS materials 3) Side by side comparison of high temperature test results for printable paste and state of the art low-density ablators

T. Boghozian

Automated Plasma Spray (APS) process feasibility study

An automated plasma spray (APS) process was developed to apply two layer (NiCrAlY and ZrO2-12Y2O3) thermal barrier coatings to aircraft and stationary gas turbine engine blade airfoils. The APS process hardware consists of four subsystems: a mechanical positioning subsystem incorporating two interlaced six degree of freedom assemblies (one for coating deposition and one for coating thickness monitoring); a noncoherent optical metrology subsystem (for in process gaging of the coating thickness buildup at specified points on the specimen); a microprocessor based adaptive system controller (to achieve the desired overall thickness profile on the specimen); and commerical plasma spray equipment. Over fifty JT9D first stage aircraft turbine blade specimens, ten W501B utility turbine blade specimens and dozens of cylindrical specimens were coated with the APS process in preliminary checkout and evaluation studies. The best of the preliminary turbine blade specimens achieved an overall coating thickness uniformity of 53 micrometers (2.1 mils), much better than is achievable manually. Comparative evaluations of coating thickness uniformity for manually sprayed and APS coated specimens were performed. One of the preliminary turbine blade evaluation specimens was subjected to a torch test and metallographic evaluation. Some cylindrical specimens coated with the APS process survived up to 2000 cycles in subsequent burner rig testing.

Fetheroff, C. W.

IRAF in the nineties

The Interactive Data Reduction and Analysis Facility (IRAF) data reduction and analysis system has been around since 1981. Today it is a mature system with hundreds of applications, and is supported on all the major platforms. Many institutions, projects, and individuals around the US and around the world have developed software for IRAF. Some of these packages are comparable in size to the IRAF core system itself. IRAF is both a data analysis system, and a programming environment. As a data analysis system it can be easily installed by a user at a remote site and immediately used to view and process data. As a programming environment IRAF contains a wealth of high and low level facilities for developing new applications for interactive and automated processing of astronomical or other data. As important as the applications programs and user interfaces are to the scientist using IRAF, the heart of the IRAF system is the programming environment. The programming environment determines to a large extent the types of applications which can be built within IRAF, what they will look like, and how they will interact with one another and with the user. While applications can be easily added to or removed from a software system, the programming environment must remain fairly stable, with carefully planned evolution and growth, over the lifetime of a system. The IRAF programming environment is the framework on which the rest of the IRAF system is built. The IRAF programming environment as it exists in 1992, and the work currently underway to enhance the environment are discussed. The structure of the programming environment as a class hierarchy is discussed, with emphasis on the work being done on the image data structures, graphics and image display interfaces, and user interfaces. The new technologies which we feel IRAF must deal with successfully over the coming years are discussed. Finally, a preview of what IRAF might look like to the user by the end of the decade is presented.

Tody, D.

TEAMS Model Analyzer

The TEAMS model analyzer is a supporting tool developed to work with models created with TEAMS (Testability, Engineering, and Maintenance System), which was developed by QSI. In an effort to reduce the time spent in the manual process that each TEAMS modeler must perform in the preparation of reporting for model reviews, a new tool has been developed as an aid to models developed in TEAMS. The software allows for the viewing, reporting, and checking of TEAMS models that are checked into the TEAMS model database. The software allows the user to selectively model in a hierarchical tree outline view that displays the components, failure modes, and ports. The reporting features allow the user to quickly gather statistics about the model, and generate an input/output report pertaining to all of the components. Rules can be automatically validated against the model, with a report generated containing resulting inconsistencies. In addition to reducing manual effort, this software also provides an automated process framework for the Verification and Validation (V&V) effort that will follow development of these models. The aid of such an automated tool would have a significant impact on the V&V process.

Tijidjian, Raffi P.

Composite-Metal-Matrix Arc-Spray Process

Arc-spray "monotape" process automated, low in cost, and produces at high rate. Ideal for development of new metal-matrix composites. "Monotape" reproducible and of high quality. Process carried out in controlled gas environment with programmable matrix-deposition rates, resulting in significant cost saving

Westfall, Leonard J.

ATC automation concepts

Information on the design of human-centered tools for terminal area air traffic control (ATC) is given in viewgraph form. Information is given on payoffs and products, guidelines, ATC as a team process, automation tools for ATF, and the traffic management advisor.

Erzberger, Heinz

Silicon solar cells by ion implantation and pulsed energy processing

A new method for fabrication of silicon solar cells is being developed around ion implantation in conjunction with pulsed electron beam techniques to replace conventional furnace processing. Solar cells can be fabricated totally in a vacuum environment at room temperature. Cells with 10% AM0 efficiency have been demonstrated. High efficiency cells and effective automated processing capabilities are anticipated.

Kirkpatrick, A. R.

Data processing for the DMSP microwave radiometer system

A software program was developed and tested to process microwave radiometry data to be acquired by the microwave sensor (SSM/T) on the Defense Meteorological Satellite Program spacecraft. The SSM/T 7-channel microwave radiometer and systems data will be data-linked to Air Force Global Weather Central (AFGWC) where they will be merged with ephemeris data prior to product processing for use in the AFGWC upper air data base (UADB). The overall system utilizes an integrated design to provide atmospheric temperature soundings for global applications. The fully automated processing at AFGWC was accomplished by four related computer processor programs to produce compatible UADB soundings, evaluate system performance, and update the a priori developed inversion matrices. Tests with simulated data produced results significantly better than climatology.

Rigone, J. L.