SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
We performed a branching ratio measurement of the most intense gamma rays in the decay of 111Ag. The sample was harvested at Argonne National Laboratory and measured at Texas A&M with the same technique as we used in our previous measurements. We made two samples and were able to measure both of them. The data is currently under analysis.
Following a review of the design options for a superconducting ion linac, we present here an alternative design for the pre-stripper section of the superconducting driver linac for the rare isotope science project (RISP) of the Institute for Basic Science in Korea. The proposed alternative design takes advantage of the recent accelerator developments at Argonne, namely for the recent ATLAS intensity and efficiency upgrade and the Fermilab proton improvement plan project (PIP-II). In particular, the state-of-the-art performance of quarter-wave (QWRs) and half-wave resonators (HWRs), the integrated steering correctors and cold beam position monitors (BPMs) for a compact cryomodule design. In order to simplify the design and avoid frequency transitions, we used two types of QWRs at 81.25 MHz while the baseline design has QWRs at 81.25 MHz and HWRs at 162.5 MHz. The new QWR types were optimized for β ~0.05 and ~0.11, respectively, and corrected for beam steering effects. Nine cryomodules are required to reach the stripping energy of 18.5 MeV/u for uranium beam. An alternative radio-frequency quadrupole (RFQ) design was also developed. It is optimized with the multi-harmonic buncher (MHB) to produce a much smaller longitudinal emittance, offering much needed flexibility for beam tuning and more tolerance to errors. Following the lattice design optimization, end-to-end beam dynamics simulations including most important sources of machine error were performed. The results showed that the design is robust and tolerant to errors with no beam loss observed for typical machine errors.
Strong electron correlation and spin-orbit coupling (SOC) can have a profound influence on the electronic properties of materials. We examined their combined influence on a two-dimensional electronic system at the atomic interface between magic-angle twisted bilayer graphene and a tungsten diselenide crystal. We found that strong electron correlation within the moiré flatband stabilizes correlated insulating states at both quarter and half filling, and that SOC transforms these Mott-like insulators into ferromagnets, as evidenced by a robust anomalous Hall effect with hysteretic switching behavior. The coupling between spin and valley degrees of freedom could be demonstrated through control of the magnetic order with an in-plane magnetic field or a perpendicular electric field. Our findings establish an experimental knob to engineer topological properties of moiré bands in twisted bilayer graphene and related systems.
Radiation-hydrodynamic simulations of directly driven fusion experiments at the Omega Laser Facility predict absorption accurately when targets are driven at low overlapped laser intensity. Discrepancies appear at increased intensity, however, with higher-than-expected laser absorption on target. Strong correlations with signatures of the two-plasmon decay (TPD) instability—including half-harmonic and hard-x-ray emission—indicate that TPD is responsible for this anomalous absorption. Scattered light data suggest that up to ≈ 30 % of the laser power reaching quarter-critical density can be absorbed locally when the TPD threshold is exceeded. A scaling of absorption versus TPD threshold parameter was empirically determined and validated using the laser–plasma simulation environment code.
The objective of our project was to develop a high efficiency, long lived WOLED using a hybrid approach to harvesting singlet and triplet excitons, as described above. WE met out GONOGO metric at the end of year one, achieving an efficiency of nearly 50 lm/W for high quality white light emission. We faced an unforeseen problem in achieving this high efficiency level at high brightness. Our hybrid devices showed a significant roll off in device efficiency as the current is raised, such that our efficiency dropped to ca. 10 lm/W at 1000 nits. This roll off precluded us form achieving our send year targets with regards to efficiency at high brightness and long device lifetime. We spent the majority of our efforts in year two trying to decrease or eliminate this efficiency roll off, but this roll off prevented us from reaching our end of program target of high efficiency at high brightness with long device lifetime. Toward the end of the sixth quarter of the program we began to investigate a new approach, which involved a tandem WOLED, with a hybrid blue/red OLED stacked on a phosphorescent green OLED. The resultant emission from the stack will be white and the tandem structure relaxes the constraints on the materials, which we believe is key issue in the high roll off in efficiency.
Hydrogen stations today serve the emerging market of light duty fuel cell vehicles, primarily in California with over 30 public retail locations. There has been a steady increase in the number of stations open and hydrogen dispensed, especially in the last two years. From 2015 to 2016, the annual amount of hydrogen dispensed increased from 27,400 kg to 109,200 kg, a nearly fourfold increase in just one year. One station dispensed nearly 12,000 kg in the second quarter of 2017. Despite the significant progress, gaps exist between current infrastructure capabilities and future requirements. For example, fuel cell vehicle applications such as buses, medium-duty, and heavy-duty trucks will gain market share and this must be considered as future customers at hydrogen stations. The expected number of light duty fuel cell vehicles in California alone are expected to grow from approximately 4,000 to over 13,000 by 2020, and 37,000 by 2023. To serve the multiple mobile fuel cell technologies and increased demand, hydrogen stations will have to increase output, decrease cost, and improve reliability. To address these challenges, the project team will demonstrate a hydrogen-focused integrated renewable energy production, storage, and transportation fuel distribution/retailing system. The proposed R&D tasks address key challenges related to light duty station/component reliability and development and validation of high flow rate system models for new applications like medium and heavy-duty truck fueling.
There is a particular need for fast tuners and phase shifters for advanced superconducting accelerator RF systems. The tuners based on ferrite, ferroelectric and piezo materials are commonly used. However, those methods suffer from one or another issue of high power loss, slow response, and narrow tuning range. We propose a robust, fast (up to ~5 MHz/sec), high efficient mechanical tuner for SRF cavities operating at the frequency 50 MHz. We develop an external mechanical tuner that is strongly coupled to the cavity. The tuner design represents a trade-off of high efficiency (low RF losses and low heat flux) and frequency tunability range. Our approach solves this trade-off issue. We propose RF design which exploits two coupled resonators so that a main high-field cavity is controlled with a small tunable resonator with a flexible metallic wall operating in a relatively low RF field. Simulations, carried out for a 7.5 MV/m 50 MHz SRF Quarter Wave Resonator (QWR), show that frequency tunability at level 10⁻³ is obtainable.
Previous research has demonstrated that tropical cyclone-related precipitation and flooding have been increased by anthropogenic global warming. Our work aims to quantify the contribution of climate change to the deadly flooding from the remnants of Hurricane Ida (2021) and its impact on human society. We developed an analysis framework that combines lessons from climate change attribution science, two-dimensional hydrodynamic modeling, and flood impact evaluation, including a social inequality index, to estimate remnants of Ida flooding and consequences responding to current (locally 1°C warmer) and future (another 1°C warmer) climate change. We find that an additional quarter to a half million people were exposed to flooding due to current and future climate change. The human influence on flood impacts was larger with deeper flood water depth (≥ 1 m) than with shallow depths. Socially vulnerable populations were found to be disproportionately more affected, and climate change exacerbates this inequality
Phthalate molecular contamination, identified in the Laser Mégajoule target chamber, can severely alter porous coatings' performance, such as glancing angle deposited quarter-wave plates (QWP). QWPs could potentially be used inside this chamber to smooth the intensity of the focal spots on the target. In this study, all-silica QWP coatings were contaminated with dimethyl phthalate. Transmission was lowered due to the absorption of phthalates, and a non-uniform retardance was induced, even after a two-month storage period in air following contamination. Infrared measurements confirmed the presence of bonds associated with phthalates within the coatings due to their sorption and only partial desorption.
A series of two-dimensional particle-in-cell simulations with speckled laser drivers was carried out to study hot electron generation in direct-drive inertial confinement fusion on OMEGA. Scaling laws were obtained for hot electron fraction and temperature as functions of laser/plasma conditions in the quarter-critical region. Using these scalings and conditions from hydro simulations, the temporal history of hot electron generation can be predicted. The scalings can be further improved to predict hard x-rays for a collection of OMEGA warm target implosions within experimental error bars. Furthermore, these scalings can be readily implemented into inertial confinement fusion design codes.
The overview of our project as well as most recent results have been presented at the NSARD review in April, and more recently during the WoNDRAM workshop. We have been dealing with recent personnel changes in the group. Miguel Bencomo, who has worked with us on this project as a postdoc at LLNL since 2019, will be terminating his appointment within the next two weeks to take a full-time appointment with Raytheon. We continue training our new team member Dan Hoff to take over data analysis from the last experiment we performed, as well as prepare for upcoming measurements. Additionally, we are working with a summer student, John Wilkinson, who is training to perform GEANT4 simulations of beta detector this summer.
Interactions of two plasmon decay (TPD) and side stimulated Raman scattering (SSRS) were studied using 3-D particle-in-cell simulations under ICF-relevant conditions for linearly and circularly polarized lasers. In the linear stage, SSRS took place under n e = 0.235n c and TPD dominated near the quarter-critical density surface and their growth rates agreed with theory. In the nonlinear stage, SSRS reduced TPD through pump depletion. Hot electrons were found to be first accelerated by the SSRS plasma waves and then by TPD plasma waves through a co-generation mechanism. Compared to the linearly polarized case with the same laser intensity, both SSRS and TPD were reduced due to the lower laser amplitude in the circularly-polarized case. As a result, a 30 percent decrease in hot electron flux was observed.
Originally this was planned as a 5 task, 3 year project, starting in May 2019. Task 1 Detecting oxidants and metal corrosion in molten chloride salt at 800°C. Task 2 Effectiveness of Zr getter using head gas sensors of inlet and outlet gases. Task 3 Cathodic protection of metal in molten salt at reducing potential. Task 4 Find reduction potential of metals in molten chloride salts & quantum modeling. Task 5 Develop corrosion test sections integrated into molten salt flow loop. After Q4, the project was scaled back and the reorganized SOPO was reduced to 3 tasks to be completed at the end of Q7 on 01/05/2021. The 3 SOPO tasks are: Task 1 Sense oxidants and the metal corrosion in molten Na-K-Mg-Cl salt at 800°C. Task 3 Cathodically protect H230 alloy in molten Na-K-Mg-Cl salt at 800C by making H230 alloy the cathode of a power supply with a chromium-rich-metal as the anode. Task 4 Find the reduction potential of Cr metal in molten Na-K-Mg-Cl salt at 800°C. The total timeline was reduced from 12 to 7 quarters with the end date being, January 5, 2021. This amounted to task 1,3 and 4 being done in Q5,6 and 7 of an extended year 1, ending on January 5, 2021. Task 1, 3 and 4 were completed. For task1) the increase of oxidants in molten salt is detected by two things: i) a positive shift of the electrode potential for a Haynes 230 alloy (H230) metal coupon versus a silver/silver-chloride reference electrode (SSE) and ii) an increase in the corrosion rate of a H230 electrode at 800C. For task 3) applying a cathodic potential (negative overpotential) to a H230 electrode versus SSE arrested the corrosion of the cathodically protected H230 compared to an unprotected “spectator H230 electrode” in the same molten chloride salt. Lastly, for task 4) the reduction potential of chrome and chrome rich, and nickel metal electrodes were measured. The most valuable outcome of this work is that a power supply can arrest metal corrosion for metal in molten chloride salt when the power supply applies a cathodic potential to bare metal, like H230, in molten chloride salts, like ternary Mg-K-Na-chloride salt. H230 is a high strength metal for containing molten chloride salt and ternary Mg-K-Na-chloride salt is used as heat transfer fluids in concentrating solar power plants. When to use cathodic protection for protecting metal in molten chloride salts? Two scenarios are envisioned: 1) for protecting high-valued components, like solar collectors and heat exchangers and 2) for protecting the bare surface in holidays (point defects) of corrosion inhibitors that are to intended to cover the entire surface of metal.
Shale is characterized by the predominant presence of nanometer-scale (1-100 nm) pores. The behavior of fluids in those pores directly controls shale gas storage and release in shale matrix and ultimately the wellbore production in unconventional reservoirs. Recently, it has been recognized that a fluid confined in nanopores can behave dramatically differently from the corresponding bulk phase due to nanopore confinement. CO 2 and H 2 O, either preexisting or introduced, are two major components that coexist with shale gas (predominately CH 4 ) during hydrofracturing and gas extraction. Note that liquid or supercritical CO 2 has been suggested as an alternative fluid for subsurface fracturing such that CO 2 enhanced gas recovery can also serve as a CO 2 sequestration process. Limited data indicate that CO 2 may preferentially adsorb in nanopores (particularly those in kerogen) and therefore displace CH 4 in shale. Similarly, the presence of water moisture seems able to displace or trap CH 4 in shale matrix. Therefore, fundamental understanding of CH 4 -CO 2 -H 2 O behavior and their interactions in shale nanopores is of great importance for gas production and the related CO 2 sequestration. This project focuses on the systematic study of CH 4 -CO 2 -H 2 O interactions in shale nanopores under high-pressure and high temperature reservoir conditions. The proposed work will help develop new stimulation strategies to enable efficient resource recovery from fewer and less environmentally impactful wells.
This report summarizes results from the project, “Development of Enabling Technologies for Chemical Looping Combustion and Chemical Looping with Oxygen Uncoupling,” which evaluated several aspects of dual fluidized bed chemical looping combustion and chemical looping with oxygen uncoupling (CLOU). The objective was to provide tools and enabling technologies to help advance fluidized bed chemical looping technology to pilot, demonstration and commercial scale. One focus area is oxygen carriers, which are key to chemical looping combustion. The copper oxygen carrier-coal ash system was systematically evaluated through a combination of thermodynamic modeling and lab-scale experiments, taking into consideration different oxygen carrier support materials and coal types. A method of mapping “safe” and “risk” zones for different combinations was established, and recommendations for target conditions are provided. In addition, a simple solution for limiting negative influence of some coal ashes, namely adding small amounts of calcium to the system, is proposed. In addition, a novel process for recovering and recycling copper from spent oxygen carriers is proposed. A new approach for design and operation of loop seals in a CLOU system was developed, and involves distinct gas injection points and a short horizontal section to help control the fate of the fluidizing gases. For the air-to-fuel reactor loop seal, the upstream side is fluidized with air, ideally input into the side rather than into the bottom, which prevents uncoupling (reduction) of the oxygen carrier before entering the fuel reactor. Also, alternative for separating oxygen carrier particles and gas in circulating fluidized bed-based chemical looping system is proposed. A new reduced reaction scheme for conversion of coal in copper-based CLOU was developed and implemented into CPFD Software’s Barracuda VR package. The resulting model provides higher fidelity than the baseline, especially when it comes to minor reactions that are part of the overall combustion environment. For in-reactor heat extraction, it was determined in this project that the best way to do that in a dual circulating fluidized-bed system is through heat exchange low in the air reactor. The air reactor is the hotter of the two and for a fast-fluidized circulating bed, the lower, more dense section has a higher heat transfer coefficient and offers more consistent particle-wall contact since it doesn’t have the splashing behavior the top of the bed does. It was determined that just the wall surface area in the lower quarter to third of the air reactor is sufficient to control temperatures in both reactors. Finally, consideration was given to a new concept for CLC, which involves a staged fuel reactor with a different type of oxygen carrier in each stage.
As part of Task 1, we have started by testing our modeling capabilities by reproducing isothermal DFIT simulations presented in the literature. To start, we have been working towards adjusting numerical parameters to reproduce DFIT tests with different fracture geometries. Then, we have focused modeling the DFIT conducted at well 58-32 (cycle 4 in zone 2). Specifically, we have carefully analyzed the influence of the aperture-contact stress relationship and investigated how two different laws affect model results.
As part of Task 1, we have started by testing our modeling capabilities by reproducing isothermal DFIT simulations presented in the literature. To start, we have been working towards adjusting numerical parameters to reproduce DFIT tests with different fracture geometries. Then, we have focused modeling the DFIT conducted at well 58-32 (cycle 4 in zone 2). Specifically, we have carefully analyzed the influence of the aperture-contact stress relationship and investigated how two different laws affect model results. We have also introduced thermal effects in the model and rerun the simulations to estimate the effect of cooling on the DFIT response. Due to the small amount of fluid injected during a DFIT, thermal effects seem to be moderate.
The objective of this project was to design and demonstrate a core-shell structured multifunctional catalyst to convert the light (dry) components of shale gas into liquid aromatic compounds (primarily benzene and toluene) in a single step. Operated in a modular oxidative aromatization system (OAS) under a cyclic redox scheme, the novel catalyst and process can significantly improve the value and transportability of distributed shale gas. Since the project started, each quarter addressed a different set of tasks related to the completion of the milestone detailed in the project award. The yearly summaries of these tasks are summarized below: Q1-Q4: • Conducted project planning and literature search. • Investigated a number of SHC redox catalysts using thermogravimetric analysis and fixed-bed reactor experiments. • Initiated process modeling towards generating two process models for the methane DHA base case and OAS process. • Developed DHA catalysts capable of producing >500 g/kg-cat-hr aromatics at 80% or greater aromatics selectivity at 700°C. Q5-Q8: • Developed alternative approaches with sequential bed configurations to enhance the aromatic yields based on OCM+DHA • Improved the zeolite synthesis efficiency by using the microwave-assisted technique and investigated the synthesis conditions on the zeolite yield, crystalline structure and morphology • Constructed a set of Aspen Plus process models with significant energy savings for OAS as compared to the base case non-oxidative DHA. • Adapted conventional hydrothermal method to be applicable to the microwave synthesizer unit for more efficient catalyst synthesis. • Studied the structure of the OCM catalyst and the dispersion of the carbonate in the redox reactions and in methane flow with Raman Spectroscopy. Q9-Q12: • Scaled up the catalyst synthesis with the microwave synthesis method. Based on its performance, procedural characterizations and catalytic performance testing were further conducted for the new microwave synthesized catalysts with the newly-developed product analysis procedure. • Developed the reaction system setup for the C2-DHA or OCM+DHA reaction product and achieved a better product collection-analysis method for the aromatic products with an improved carbon balance. The product from the OCM reaction exhibited complicated effects on the DHA catalyst. • Conducted additional OCM catalyst characterization using Near Ambient Pressure X-ray Photoelectron Spectroscopy and in situ Raman characterization • Validated the significant energy savings for OAS as compared to the base case non-oxidative DHA. Successfully set up the simulation model for the OCM+DHA+SHC reaction system based on the updated experimental results from NCSU. Q13-End of project: • Synthesized new zeolite catalysts by the microwave method, conducted characterizations (XRD, SEM, and TEM) and catalytic behavior testing. • Explored the “wet” C 2 H 6 and C 2 H 4 DHA reactions with using steam co-feed. A subsequent reduction as the regeneration step can regenerate the DHA catalyst and recover 99% activity of the fresh performance. • Achieved a 15.3% single-pass aromatic yield from methane by rationally combining the OCM and DHA at different temperatures. • Conducted a 105-hour stability test with an improved regeneration procedure, with an average aromatic yield of 13.8%. • Developed new catalyst and achieved a record-high 23.2% yield.