SEARCH · Search NASA

Results for “REINFORCED PLASTIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Mechanical properties of a fiberglass prepreg system at cryogenic and other temperatures

The compressor driving the flow in the National Transonic Facility, which is nearing completion at the Langley Research Center, has 25 fiberglass blades. E-glass cloth with a pre-impregnated epoxy resin has been selected as the material for the fan blades because of its low cost, high damping, and fatigue resistance. A complete characterization is presented of this fan blade fiberglass system at temperatures of 367 K, room temperature, and 89 K. The characterization test results suggest that the material follows the general trends of metals and other glass-reinforced plastics at cryogenic temperatures. A slight diminution in strength was observed at the elevated temperature. The tests included the following: tensile, compression, fatigue, inplane shear, interlaminar shear, thermal expansion, creep, and thermal cycle.

Klich, P. J.↗

NASA NTRS1982

Photo-orthotropic elasticity - A new technique for stress analysis of composites

This paper deals with the application of photoelastic methods to glass fiber reinforced plastics. The basic principles governing the photoelastic response in birefringent orthotropic composites are briefly reviewed. Then, three important aspects of photo-orthotropic elasticity, namely, photoelastic calibration, separation of principal stresses, and application to problems of engineering importance, are considered in detail. A new calibration specimen is proposed for determining the three independent photoelastic constants: an orthotropic half-plane subjected to a concentrated edge load. From the isochromatic response, the three stress-fringe values can be obtained by a least-squares procedure based on the theoretical stress distribution. Next, four methods of separating the principal stresses in birefringent composite models are proposed: the method of drilling small holes at the points of interest, the method of oblique incidence, the method of combining the transmitted photoelastic response with the reflected photoelastic response, and the method of birefringence dispersion.

Prabhakaran, R.↗

NASA NTRS1984

Fabrication of Multi-Ply Birefringent Fibrous Composite Laminates

Fabrication method produces unidirectional, multi-ply, transparent birefringent fibrous composite laminates for use in macromechanical stress analysis conducted by means of anisotropic photoelasticity. New laminates glass-fiber-reinforced plastics for which matrix and fibers have same index of refraction. Method utilized in structural applications of composites.

Daniel, I.↗

NASA NTRS1982

Composite Material Application to Liquid Rocket Engines

The substitution of reinforced plastic composite (RPC) materials for metal was studied. The major objectives were to: (1) determine the extent to which composite materials can be beneficially used in liquid rocket engines; (2) identify additional technology requirements; and (3) determine those areas which have the greatest potential for return. Weight savings, fabrication costs, performance, life, and maintainability factors were considered. Two baseline designs, representative of Earth to orbit and orbit to orbit engine systems, were selected. Weight savings are found to be possible for selected components with the substitution of materials for metal. Various technology needs are identified before RPC material can be used in rocket engine applications.

Judd, D. C.↗

NASA NTRS1982

Strength criteria for composite materials (a literature survey)

Literature concerning strength (failure) criteria for composite materials is reviewed with emphasis on phenomenological failure criteria. These criteria are primarily intended to give a good estimation of the safety margin with respect to failure for arbitrary multiaxial stress states. The failure criteria do not indicate the types of fracture that will occur in the material. The collection of failure criteria is evaluated for applicability for the glass reinforced plastics used in mine detectors. Material tests necessary to determine the parameters in the failure criteria are discussed.

Roode, F.↗

NASA NTRS1983

A small and light weight heat exchanger for on-board helium refrigerator

A small and light weight heat exchanger used for small helium refrigerator has been developed by Sumitomo Heavy Industries, Ltd. This heat exchanger is a laminated metal heat exchanger which consists of perforated aluminum metal plates and glassfiber reinforced plastic separators. The size is from 100 mm to 28 mm in diameter and about 300 mm in length. The weight is from 2.5 kg to 0.6 kg. Also it can be used between room temperature and liquid helium temperature. The thermal efficiency obtained has been more than 96%. The heat exchanger has been practically used for on-board helium refrigerator in Japanese National Railways' superconducting magnetic levitated trains.

Koizumi, T.↗

NASA NTRS1984

Composites for Increased Wear Resistance: Current Achievements and Future Prospects

The various ways in which reductions in wear and/or friction can be achieved by the use of composite materials are reviewed. Reinforced plastics are emphasized and it is shown that fillers and fibers reduce wear via several mechanisms additional to their role of increasing overall mechanical strength, preferential transfer, counter face abrasion, preferential load support, or third-body formation on either the composite or its counterface. Examples are given from recent work on thin layer composites of the type widely used as dry bearings in aircraft flight control mechanisms. Developments in metal based composites and carbon-carbon composites for high energy brakes are discussed. The aspects which could benefit by increased fundamental understanding identified and the types of composites which appear to have greatest potential for further growth are indicated.

Lancaster, J. K.↗

NASA NTRS1984

Growian rotor blades: Production development, construction and test

Development and construction of three 50 m rotor blades for a 3 MW wind turbine are described. A hybrid concept was chosen, i.e., a load carrying inflexible steel spar and a glass fiber reinforced plastic skin. A test blade was constructed and static loading tests, dynamic vibration tests and fatigue tests on critical welds as well as at the connection between spar and blade skin were performed. All test results show good accordance with calculated values, and were taken into consideration during the construction of two rotor blades.

Thiele, H. M.↗

NASA NTRS1984

Hygrothermal effects on stresses and deformations in a bonded fiber-reinforced plastic/aluminum system

The hygrothermal effect on time dependent mechanical behavior of a model of nonsymmetrical bonded fiber-reinforced plastic (FRP)/aluminum system was investigated analytically. It was found that a linear viscoelastic closed form solution is sufficient for the prediction model deformations for short periods of time and small strains, while a numerical finite-element solution is preferable for determining adhesive stresses and deformational behavior of the model at any time. The thermoelastic numerical solution shows a certain decrease with time of adhesive stresses, which does not seem to affect significantly the global deformations of the model. On the other hand, it was found that the presence of moisture within the polymeric adhesive layer causes significant decrease in adhesive stresses, which affects deformational changes with time, far beyond the level predicted by the static solution.

Yaniv, G.↗

NASA NTRS1985

Determining Fiber Orientation in Graphite-Reinforced Composites

Orientation of fibers in graphite-fiber-reinforced plastics easily determined with new method. Materials scientists thus ensure that fibers, usually not visible after graphite/plastic composite has been cured, properly oriented in test specimens and test results accurately represent the characteristics of composite. Method based on fact that continuous graphite fibers embeded in cured polymer matrix actually parallel conductors. Thus, resistance measured across laminate is at minimum when probes of ohmmeter connected to opposite ends of fibers.

Daniels, J. G.↗

NASA NTRS1985

Electron emission and acoustic emission from the fracture of graphite/epoxy composites

In past studies it has been shown that the fracture of materials leads to the emission of a variety of species, including electrons, ions, neutral molecules, and photons, all encompassed by the term 'fractoemission' (FE). In this paper, electron emission (EE) from the fracture of single graphite fibers and neat epoxy resin is examined. Measurements of EE are also combined with the detection of acoustic emission (AE) during the testing of graphite-epoxy composite specimens with various fiber orientation. The characteristics of these signals are related to known failure mechanisms in fiber-reinforced plastics. This study suggests that by comparing data from AE and FE measurements, one can detect and distinguish the onset of internal and external failure in composites. EE measurements are also shown to be sensitive to the locus of fracture in a composite material.

Dickinson, J. T.↗

NASA NTRS1985

Viscoelastic behavior and life-time predictions

Fiber reinforced plastics were considered for many structural applications in automotive, aerospace and other industries. A major concern was and remains the failure modes associated with the polymer matrix which serves to bind the fibers together and transfer the load through connections, from fiber to fiber and ply to ply. An accelerated characterization procedure for prediction of delayed failures was developed. This method utilizes time-temperature-stress-moisture superposition principles in conjunction with laminated plate theory. Because failures are inherently nonlinear, the testing and analytic modeling for both moduli and strength is based upon nonlinear viscoelastic concepts.

Dillard, D. A.↗

NASA NTRS1986

Damping characteristics of damaged fiber composite components

Defects in fiber composite components produce changes with respect to the vibrational characteristics of the material. These changes can be recognized in the form of a frequency shift or an alteration of the damping process. The present investigation is concerned with questions regarding the possibility of a utilization of the changes in suitable defect-detecting inspection procedures. A description is given of a method for measuring the damping characteristics of a specimen. This method provides a spectrum of the damping coefficients of the sample as a basis for a comprehensive evaluation of the damping behavior. The correlation between defects and change in the damping characteristics is demonstrated with the aid of results obtained in measurements involving specimens of carbon-fiber composites and a component consisting of glass-fiber-reinforced plastics.

Eberle, K.↗

NASA NTRS1985

Durability predictions of adhesively bonded composite structures using accelerated characterization methods

The utilization of adhesive bonding for composite structures is briefly assessed. The need for a method to determine damage initiation and propagation for such joints is outlined. Methods currently in use to analyze both adhesive joints and fiber reinforced plastics is mentioned and it is indicated that all methods require the input of the mechanical properties of the polymeric adhesive and composite matrix material. The mechanical properties of polymers are indicated to be viscoelastic and sensitive to environmental effects. A method to analytically characterize environmentally dependent linear and nonlinear viscoelastic properties is given. It is indicated that the methodology can be used to extrapolate short term data to long term design lifetimes. That is, the method can be used for long term durability predictions. Experimental results for near adhesive resins, polymers used as composite matrices and unidirectional composite laminates is given. The data is fitted well with the analytical durability methodology. Finally, suggestions are outlined for the development of an analytical methodology for the durability predictions of adhesively bonded composite structures.

Brinson, H. F.↗

NASA NTRS1985

Viscoelastic behavior and lifetime (durability) predictions

A method for lifetime or durability predictions for laminated fiber reinforced plastics is given. The procedure is similar to but not the same as the well known time-temperature-superposition principle for polymers. The method is better described as an analytical adaptation of time-stress-super-position methods. The analytical constitutive modeling is based upon a nonlinear viscoelastic constitutive model developed by Schapery. Time dependent failure models are discussed and are related to the constitutive models. Finally, results of an incremental lamination analysis using the constitutive and failure model are compared to experimental results. Favorable results between theory and predictions are presented using data from creep tests of about two months duration.

Brinson, R. F.↗

NASA NTRS1986

Features and technologies of ERS-1 (ESA) and X-SAR antennas

Features and technologies of planar waveguide array antennas developed for spaceborne microwave sensors are described. Such antennas are made from carbon fiber reinforced plastic (CFRP) employing special manufacturing and metallization techniques to achieve satisfactory electrical properties. Mechanical design enables deployable antenna structures necessary for satellite applications (e.g., ESA ERS-1). The slotted waveguide concept provides high aperture efficiency, good beamshaping capabilities, and low losses. These CFRP waveguide antennas feature low mass, high accuracy and stiffness, and can be operated within wide temperature ranges.

Schuessler, R.↗

NASA NTRS1987

The surface properties of carbon fibers and their adhesion to organic polymers

The state of knowledge of the surface properties of carbon fibers is reviewed, with emphasis on fiber/matrix adhesion in carbon fiber reinforced plastics. Subjects treated include carbon fiber structure and chemistry, techniques for the study of the fiber surface, polymer/fiber bond strength and its measurement, variations in polymer properties in the interphase, and the influence of fiber matrix adhesion on composite mechanical properties. Critical issues are summarized and search recommendations are made.

Bascom, W. D.↗

NASA NTRS1988

Resources: NASA for entrepreneurs

The services of NASA's Technology Utilization Program are detailed and highlights of spinoff products in various stages of completion are described. Areas discussed include: Stirling engines for automotive applications, klystron tubes used to reduce power costs at UHF television stations, sports applications of riblet film (e.g., boat racing), reinforced plastic for high-temperature applications, coating technology appropriate for such applications similar to the renovation of the Statue of Liberty, and medical uses of fuel pump technology (e.g., heart pumps).

Jannazo, Mary Ann↗