Search NASA⌕ Search

SEARCH · Search NASA

Results for “Radiation Tolerance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Grain boundary strain as a determinant of localized sink efficiency

The opportunity to achieve radiation tolerance in crystalline materials hinges on understanding the structure and response of grain boundary sinks to irradiation. A common descriptor of grain boundary efficiency as a defect sink is the denuded zone, which is a defect free zone adjacent to the grain boundary dictated by its ability to absorb radiation induced defects. This descriptor is often used at the mesoscale, which requires an averaging of absorption events. In this paper, we resolve the defect sink efficiency as a function of interfacial strain with respect to grain boundary character, and correlate high levels of grain boundary strain to an enhanced absorption efficiency. Here, we also introduce a key relationship between localized strain in proximity with the grain boundary sink and the variation absorption efficiency associated with these regions, revealing the pitfalls of averaging absorption events along a grain boundary, and presenting a path forward toward improved models for denuded zones and localized grain boundary absorption phenomena.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Unraveling the Early-Stage Ordering of Krypton Solid Bubbles in Molybdenum: A Multimodal Study

Self-organization of defects such as fission gas bubbles in materials can lead to high inventory capacity for fission gas storage and help mitigate swelling caused by fission gases in nuclear fuel materials under radiation in nuclear reactors. Here, we report the physical mechanism of self-organization of krypton (Kr) gas bubbles in molybdenum (Mo) under ion implantation. The ion fluence and temperature-dependent formation of Kr solid bubble superlattice (SBS) in Mo were investigated by using both synchrotron-based small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). Early stage self-organization of gas bubbles is observed at a fluence of 2.5 × 10 16 ions/cm 2 at temperatures of 300–400 °C. The bubble lattice constant increases with increasing implantation temperature from 300 to 400 °C. Both experiments and atomic kinetic Monte Carlo modeling indicate that the Kr solid bubbles are weakly ordered in comparison to previously studied helium (He) gas bubble superlattice (GBS) while the lattice constant are relatively smaller for Kr SBS compared to that of He GBS. The irradiation conditions suggest that spinodal decomposition, which is a form of phase separation, probably precedes gas bubble ordering in Mo. Altogether, our work sheds light on the formation mechanism of noble gas superlattice toward the development of radiation-tolerant materials which are important for the design of advanced nuclear reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hadron-Induced Radiation Damage in Fast Heavy Inorganic Scintillators

Fast and heavy inorganic scintillators with suitable radiation tolerance are required to face the challenges presented at future hadron colliders of high energy and intensity. Up to 5 GGy and 5 × 1018 neq/cm2 of one-MeV-equivalent neutron fluence is expected by the forward calorimeter at the Future Hadron Circular Collider. This paper reports the results of an investigation of proton- and neutron-induced radiation damage in various fast and heavy inorganic scintillators, such as LYSO:Ce crystals, LuAG:Ce ceramics, and BaF2 crystals. The experiments were carried out at the Blue Room with 800 MeV proton fluence up to 3.0 × 1015 p/cm2 and at the East Port with one MeV equivalent neutron fluence up to 9.2 × 1015 neq/cm2, respectively, at the Los Alamos Neutron Science Center. Experiments were also carried out at the CERN PS-IRRAD proton facility with 24 GeV proton fluence up to 8.2 × 1015 p/cm2. Research and development will continue to develop LuAG:Ce ceramics and BaF2:Y crystals with improved optical quality, F/T ratio, and radiation hardness.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Carbon nanotube (CNT) metal composites exhibit greatly reduced radiation damage

Radiation damage of structural materials leads to mechanical property degradation, eventually inducing failure. Secondary-phase dispersoids or other radiation defect sinks are often added to materials to boost their radiation resistance. We demonstrate that a metal composite made by adding 1D carbon nanotubes (CNTs) to aluminum (Al) exhibits superior radiation resistance. In situ ion irradiation with transmission electron microscopy (TEM) and atomistic simulations together reveal the mechanisms of rapid defect migration to CNTs, facilitating defect recombination and enhancing radiation tolerance. The origin of this effect is an evolving stress gradient in the Al matrix resulting from CNT transformation under irradiation, and the stability of resulting carbides. Extreme value statistics of large defect behavior in our simulations highlight the role of CNTs in reducing accumulated damage. Furthermore, this approach to controlling defect migration represents a promising opportunity to enhance the radiation resistance of nuclear materials without detrimental effects.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Characterization of the ATLAS Liquid Argon Front-End ASIC ALFE2 for the HL-LHC upgrade

In this study, ALFE2 is an ATLAS Liquid Argon Calorimeter (LAr) Front-End ASIC designed for the HL-LHC upgrade. ALFE2 comprises four channels of pre-amplifiers and CR-(RC) 2 shapers with adjustable input impedance. ALFE2 features two separate gain outputs to provide 16-bit dynamic-range coverage and an optimum resolution. ALFE2 is characterized using a Front-End Test Board (FETB) based on a Zynq UltraScale+ MPSoC and two octal-channel 16-bit high-speed ADCs. The test results indicate that ALFE2 fulfills or greatly exceeds all specifications on gain, noise, linearity, uniformity, and radiation tolerance.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

A prototype scintillator real‐time beam monitor for ultra‐high dose rate radiotherapy

Background: FLASH Radiotherapy (RT) is an emergent cancer RT modality where an entire therapeutic dose is delivered at more than 1000 times higher dose rate than conventional RT. For clinical trials to be conducted safely, a precise and fast beam monitor that can generate out-of-tolerance beam interrupts is required. This paper describes the overall concept and provides results from a prototype ultra-fast, scintillator-based beam monitor for both proton and electron beam FLASH applications. Purpose: A FLASH Beam Scintillator Monitor (FBSM) is being developed that employs a novel proprietary scintillator material. The FBSM has capabilities that conventional RT detector technologies are unable to simultaneously provide: (1) large area coverage; (2) a low mass profile; (3) a linear response over a broad dynamic range; (4) radiation hardness; (5) real-time analysis to provide an IEC-compliant fast beam-interrupt signal based on true two-dimensional beam imaging, radiation dosimetry and excellent spatial resolution. Methods: The FBSM uses a proprietary low mass, less than 0.5 mm water equivalent, non-hygroscopic, radiation tolerant scintillator material (designated HM: hybrid material) that is viewed by high frame rate CMOS cameras. Folded optics using mirrors enable a thin monitor profile of ∼10 cm. A field programmable gate array (FPGA) data acquisition system generates real-time analysis on a time scale appropriate to the FLASH RT beam modality: 100–1000 Hz for pulsed electrons and 10–20 kHz for quasi-continuous scanning proton pencil beams. An ion beam monitor served as the initial development platform for this work and was tested in low energy heavy-ion beams ( 86 Kr +26 and protons). A prototype FBSM was fabricated and then tested in various radiation beams that included FLASH level dose per pulse electron beams, and a hospital RT clinic with electron beams. Results: Results presented in this report include image quality, response linearity, radiation hardness, spatial resolution, and real-time data processing. Furthermore, the HM scintillator was found to be highly radiation damage resistant. It exhibited a small 0.025%/kGy signal decrease from a 216 kGy cumulative dose resulting from continuous exposure for 15 min at a FLASH compatible dose rate of 237 Gy/s. Measurements of the signal amplitude versus beam fluence demonstrate linear response of the FBSM at FLASH compatible dose rates of >40 Gy/s. Comparison with commercial Gafchromic film indicates that the FBSM produces a high resolution 2D beam image and can reproduce a nearly identical beam profile, including primary beam tails. The spatial resolution was measured at 35–40 µm. Tests of the firmware beta version show successful operation at 20 000 Hz frame rate or 50 µs/frame, where the real-time analysis of the beam parameters is achieved in less than 1 µs. Conclusions: The FBSM is designed to provide real-time beam profile monitoring over a large active area without significantly degrading the beam quality. A prototype device has been staged in particle beams at currents of single particles up to FLASH level dose rates, using both continuous ion beams and pulsed electron beams. Using a novel scintillator, beam profiling has been demonstrated for currents extending from single particles to 10 nA currents. Radiation damage is minimal and even under FLASH conditions would require ≥50 kGy of accumulated exposure in a single spot to result in a 1% decrease in signal output. Beam imaging is comparable to radiochromic films, and provides immediate images without hours of processing. Real-time data processing, taking less than 50 µs (combined data transfer and analysis times), has been implemented in firmware for 20 kHz frame rates for continuous proton beams.

2D beam imaging↗
DOE OSTI2021

Improvement of Front-Junction GaInP by Point-Defect Injection and Annealing

Traditional front junction GaInP solar cells are radiation tolerant and can have good diffusion length, but have limited voltage and thus efficiency. Here, we investigate the impact of annealing on GaInP device performance. First, Zn-doped GaInP/AlGaInP double heterojunction structures are studied in order to investigate the impact of annealing in a simple structure. While standard anneals lower diffusion length and lifetime, annealing after injecting point-defects improves material quality, presumably by eliminating sources of non-radiative recombination. Atomic ordering is reduced by the anneal, which raises the device bandgap and requires consideration. These results can be used to improve front junction device performance while controlling the bandgap. Then, GaInP front-junction devices are created using anneals with and without point-defect injection. Voc and EQE trends follow the diffusion length and lifetime trends from the DH structures. Baseline devices have Woc of 0.484 V, raising to 0.504 V after a high temperature anneal. However, injecting point defects prior to the anneal results in a front junction device with Woc of 0.405 V and a diffusion length greater than 8 micrometers. Optimized front-junction GaInP devices with an ARC have ~20% efficiency without a rear reflector.

anneal↗
DOE OSTI2021

Improvement of Front-Junction GaInP by Point-Defect Injection and Annealing: Preprint

Traditional front junction GaInP solar cells are radiation tolerant and can have good diffusion length, but have limited voltage and thus efficiency. Here, we investigate the impact of annealing on GaInP device performance. First, Zn-doped GaInP/AlGaInP double heterojunction structures are studied in order to investigate the impact of annealing in a simple structure. While standard anneals lower diffusion length and lifetime, annealing after injecting point-defects improves material quality, presumably by eliminating sources of non-radiative recombination. Atomic ordering is reduced by the anneal, which raises the device bandgap and requires consideration. These results can be used to improve front junction device performance while controlling the bandgap. Then, GaInP front-junction devices are created using anneals with and without point-defect injection. Voc and EQE trends follow the diffusion length and lifetime trends from the DH structures. Baseline devices have Woc of 0.484 V, raising to 0.504 V after a high temperature anneal. However, injecting point defects prior to the anneal results in a front junction device with Woc of 0.405 V and a diffusion length greater than 8 micrometers. Optimized front-junction GaInP devices with an ARC have ~20% efficiency without a rear reflector.

anneal↗
DOE OSTI2023

Proton radiation effects on electronic defect states in MOCVD-grown (010) β -Ga 2 O 3

The impact of 1.8 MeV proton irradiation on metalorganic chemical vapor deposition grown (010) β-Ga 2 O 3 Schottky diodes is presented. It is found that after a 10.8 × 10 13 cm –2 proton fluence the Schottky barrier height of (1.40 ± 0.05 eV) and the ideality factor of (1.05 ± 0.05 ) are unaffected. Capacitance–voltage extracted net ionized doping curves indicate a carrier removal rate of 268 ± 10 cm –1 . The defect states responsible for the observed carrier removal are studied through a combination of deep level transient and optical spectroscopies (DLTS/DLOS) as well as lighted capacitance–voltage (LCV) measurements. The dominating effect on the defect spectrum is due to the E c -2.0 eV defect state observed in DLOS and LCV. This state accounts for ~75 % of the total trap introduction rate and is the primary source of carrier removal from proton irradiation. Of the DLTS detected states, the E c -0.72 eV state dominated but had a comparably smaller contribution to the trap introduction. These two traps have previously been correlated with acceptor-like gallium vacancy-related defects. Several other trap states at E C -0.36, E C -0.63, and E C -1.09 eV were newly detected after proton irradiation, and two pre-existing states at E C -1.2 and E C -4.4 eV showed a slight increase in concentration after irradiation, together accounting for the remainder of trap introduction. However, a pre-existing trap at E c -0.40 eV was found to be insensitive to proton irradiation and, therefore, is likely of extrinsic origin. Furthermore, the comprehensive defect characterization of 1.8 MeV proton irradiation damage can aid the modeling and design for a range of radiation tolerant devices.

42 ENGINEERING↗
DOE OSTI2022

Phase instabilities in austenitic steels during particle bombardment at high and low dose rates

Disruption of phase stability by energetic particle bombardment is a major challenge in designing advanced radiation-tolerant alloys and ion beam processing of nanocomposites. Particularly, ballistic dissolution susceptibility of different solute nanocluster species in alloys is poorly understood. Here, low dose rate neutron irradiations were conducted on a Fe-Cr-Ni based austenitic steel in the BOR-60 reactor (9.4 × 10 -7 dpa/s, 318 °C) followed by accelerated dose rate ion irradiations at multiple temperatures ( 10 -3 dpa/s, 380 – 420 °C). Using atom probe tomography, the stability of radiation-enhanced Cu-rich and radiation-induced Ni-Si-Mn-rich nanoclusters was evaluated. During neutron irradiation, Cu-rich clusters nucleated with their core concentrations progressively increasing with dose, while Ni-Si-Mn-rich clusters formed and evolved into G-phase precipitates. Ion irradiations dramatically altered the nanoclusters. Cu-rich clusters were ballistically dissolved, but Ni-Si-Mn-rich clusters remained stable and coarsened with dose at 400 and 420 °C, highlighting that different nanocluster species in a single microstructure can have innately distinct ballistic dissolution susceptibilities. Solute-specific recoil rates were incorporated into the Heinig precipitate stability model, which shows that in addition to radiation-enhanced diffusion, recovery from ballistic dissolution depends on solute concentration gradient near cluster interfaces. Finally, the combined experimental-modeling study quantified the critical temperatures and damage rates where ballistic dissolution dominates for each cluster species.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Radiation-Induced Error Mitigation by Read-Retry Technique for MLC 3-D NAND Flash Memory

Here, we have evaluated the Read-Retry (RR) functionality of the 3-D NAND chip of multilevel-cell (MLC) configuration after total ionization dose (TID) exposure. The RR function is typically offered in the high-density state-of-the-art NAND memory chips to recover data once the default memory read method fails to correct data with error correction codes (ECCs). In this work, we have applied the RR method on the irradiated 3-D NAND chip that was exposed with a Co-60 gamma-ray source for TID up to 50 krad (Si). Based on our experimental evaluation results, we have proposed an algorithm to efficiently implement the RR method to extend the radiation tolerance of the NAND memory chip. Our experimental evaluation shows that the RR method coupled with ECC can ensure data integrity of MLC 3-D NAND for TID up to 50 krad (Si).

3-D NAND↗
DOE OSTI2021

Irradiation-induced amorphization of Fe-Y-based second phase particles in accident-tolerant FeCrAl alloys

Here, second phase intermetallic particles in an advanced accident-tolerant FeCrAl (Fe-13Cr-5Al-2Mo) alloy are formed in the α-Fe matrix during processing. These particles are prominently related to the added Y. Neutron irradiation to ~7 displacements per atom (dpa) with a dose rate of ~8.16 × 10 -7 dpa/s at 282 °C resulted in the amorphization of these precipitates which could degrade the mechanical properties of the FeCrAl alloys. Analytical electron microscopy and diffraction analysis combined with structural freedom analysis have been used to investigate the radiation resistance of the second phase particles. Radiation tolerance is closely linked to the particle Fe-Y content and can be tailored using the structure freedom value.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rad-hard readout system for Timepix3 Hybrid Pixel Detectors

The Beam Gas Ionisation (BGI) profile monitor, located in the Proton Synchrotron (PS) and Super Proton Synchrotron (SPS) at CERN, requires a radiation-tolerant readout system to transfer data from the challenging accelerator surroundings to the back-end for processing. The system needs to control and acquire data from four Timepix3 Hybrid Pixel Detectors (HPDs) located directly inside the beam pipe, a highly radioactive environment. It must ensure reliability given limited hardware access and preserve signal integrity for the high-speed data (32 channels at 320 MHz). However, due to the unavailability of a suitable rad-hard Timepix3 readout, the Beam Instrumentation PiXeL (BIPXL) readout system was designed to meet these requirements. This system employs radiation-hardened components such as the GBTx and the FEASTMP, both developed at CERN. It will be compatible with forthcoming hybrid pixel detector initiatives in similarly harsh radiation conditions.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

The Need for a Maximum Intensity Accident in ANS 8-Series Standards

The Y-12 National Security Complex has installed one Criticality Accident Alarm System (CAAS) under the ANS 8.3 framework as a safety significant system, and is in the process of designing, installing, and qualifying another. As a safety significant system, the Y-12 CAAS is required to demonstrate that it is able to perform its function and actuate an alarm when exposed to the radiation from both a Minimum Accident of Concern and a maximum intensity accident. The ANS 8-series standards do not present a maximum accident to be considered, nor do they specify radiation tolerance requirements for the CAAS equipment, leading CAAS vendors to potentially use other standards that provide inadequate criteria. In this paper, the historical basis and need for a maximum intensity accident in the ANS standards is discussed, the fission rate of a maximum intensity accident is proposed, and the effects of this accident on CAAS analysis and the vendor’s equipment qualification are discussed.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2020

Radiation effects in Mn+1AXn phases

M n+1 AX n phases exhibit unique laminated atomic structures that result in properties typical of both ceramics and metals. Due to their unusual characteristics, these materials have been proposed for use in a wide variety of industrial applications, including in nuclear reactors—both fission and fusion systems—where they will be exposed to extreme irradiation conditions and high temperatures. Recently, numerous studies have investigated radiation effects on the M n+1 AX n phases, revealing complex behavior—phase transformations, surface modification, and mechanical property changes—induced by ion or neutron irradiation over a range of temperatures. This review summarizes recent experimental and theoretical work on the response of the M n+1 AX n phases to irradiation and discusses the intrinsic controls on the radiation tolerance of these materials. Based on the review of the present body of work, a comprehensive understanding of the mechanisms of irradiation-induced structural modification and defect evolution in M n+1 AX n phases is developed, as well as proposed strategies for designing novel M n+1 AX n phases with enhanced performance under extreme irradiation conditions.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Development of interatomic potential and effect of ordering on defect properties in CrMnV

Developing materials that can withstand extreme environments, such as high radiation doses and elevated temperatures, is crucial for next-generation particle accelerators, including the 2.4 MW Long-Baseline Neutrino Facility. High-Entropy Alloys have emerged as promising candidates for beam window materials due to their superior mechanical strength, corrosion resistance, and radiation tolerance. In this study, we focus on the Cr–Mn–V alloy system, developing and employing machine-learning interatomic potentials (MLIPs) to investigate the formation of an ordered phase and its influence on defect properties. Using hybrid Monte Carlo-Molecular Dynamics simulations, we observe the formation of a B2-ordered phase at lower temperatures, consistent with Density Functional Theory (DFT) predictions. Ordered structures display a bimodal distribution of migration energies and reduced mean square displacement values, indicating suppressed vacancy diffusion. Our results also show that the migration energy barrier varies based on the atomic species, with Mn and V exhibiting the highest and lowest average barriers, respectively. These findings suggest that atomic ordering inhibits defect mobility, potentially enhancing the radiation resistance of CrMnV alloys. The validated MLIP provides a reliable framework for simulations that are faster than traditional DFT while maintaining the accuracy required to study defect and ordering properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A non-intrusive framework using acoustic signals and deep learning for boiling diagnostics in visual-limited environments

Accurate monitoring of boiling heat transfer is critical for safeguarding high-power systems operating in environments where conventional optical diagnostics are hindered by radiation fields or restricted visual accessibility. This study presents a non-intrusive framework that integrates hydroacoustic sensing with deep learning to infer near-wall boiling characteristics and enable predictive thermal assessment without visual access. In a prototypical subcooled flow-boiling facility representative of the Isotope Production Facility (IPF) at Los Alamos, hydrophones capture boiling-induced acoustic emissions that are transformed into background-removed Short-Time Fourier Transform (STFT) spectrograms. A convolutional neural network (CNN) then regresses heat flux, wall superheat, and key bubble parameters directly from these spectrograms. The CNN achieved predictive accuracy under nominal conditions and demonstrated robustness and generalization under acoustic noise for Signal-to-Noise Ratios (SNRs) down to approximately 0 dB. When integrated into an ANSYS CFX wall-boiling model, the acoustically inferred parameters reproduced boiling curve and critical heat flux (CHF) values consistent with image-based benchmarks. Furthermore, the model retained reliable performance under moderate variations in bulk temperature, flow rate, and hydrophone placement, confirming its generalizability across practical boundary conditions. These results demonstrate the feasibility of hydroacoustic-based deep learning as a viable path toward real-time, radiation-tolerant boiling diagnostics and predictive thermal safety assessment in inaccessible systems such as the IPF.

42 ENGINEERING↗