Search NASA⌕ Search

SEARCH · Search NASA

Results for “Raman process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The Nonradiative Properties of Self–Trapped Holes in Ultra–Wide Bandgap Gallium Oxide Film

The photoluminescence (PL) of self-trapped holes (STH) in ultra-wide bandgap β-Ga 2 O 3 is commonly its most dominant light emission and is an inherent property. Thus, gaining knowledge of the crystal dynamics that impact the PL properties is vital to sensor and other technologies. The PL, Raman-phonons, and their interactions are studied at an extreme temperature range of 77–622 K. The PL is studied up to the bandgap value of ≈5 eV. It is found that the high-energy Raman modes provide a major route to the nonradiative process of the PL via STH–phonon interaction with an activation energy of 72 meV. This dynamic is modeled with the configurational coordinate scheme at the strong phonon coupling limit. The exceptionally broad Gaussian PL linewidth manifests this coupling. The weak temperature response of the PL energy peak position indicates that the STH has characteristics of a deep-level defect. This contrasts with the large redshift of ≈220 meV of the optical gap of the film, ascertained from transmission. Unlike the temperature response of the high-energy phonons, the behavior of the low-energy phonons is found to follow the Bose–Einstein population increase, indicating no strong interaction with the STH.

Raman↗
DOE OSTI2022

Isotopic Signatures of Lithium Carbonate and Lithium Hydroxide Monohydrate Measured Using Raman Spectroscopy

Lithium isotopic ratios have wide ranging applications as chemical signatures, including improved understanding of geochemical processes and battery development. Measurement of isotope ratios using optical spectroscopies would provide an alternative to traditional mass spectrometric methods, which are expensive and often limited to a chemical laboratory. In this work, Raman spectra of 7 Li 2 CO 3 , 6 Li 2 CO 3 , 7 LiOH*H 2 O and 6 LiOH*H 2 O have been measured to determine the effect of lithium isotope substitution on the Raman molecular vibrations. Thirteen peaks were observed in the spectrum of lithium carbonate, with discernable isotopic shifts occurring in eleven of the thirteen vibrations, two of which have not been previously reported in the literature. The spectrum of lithium hydroxide monohydrate contained nine peaks, with discernable isotopic shifts occurring in eight of the nine vibrations, four of which have not been previously reported in the literature. The Raman spectral data reported here for lithium carbonate and lithium hydroxide monohydrate are in agreement with the previously reported works in the literature, in which the Raman active modes of these molecules were first identified and assigned. However, due to the stability and resolution of the detection system used in this work, isotopic shifts with a magnitude less than one wavenumber have been identified. Principal Component Regression was used to evaluate the sensitivity to isotopic content of small Raman peak shifts in Li 2 CO 3 and indicates differences greater than 2 atom-% could be reliably determined. These measurements add to the body of work on lithium isotope Raman spectroscopy for these two compounds and increases the number of Raman bands which could be used for lithium isotope content analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Selective photo-excitation of molecules enabled by stimulated Raman pre-excitation

Double resonance excitation, where the energies of vibrational and electronic molecular transitions are combined in a single, sequential excitation process, was introduced in the 1970s but has only been recently applied to microscopy due to the immense progress in Raman spectroscopy. The value of the technique is in combining the chemical selectivity of IR or Raman excitation with the much larger cross-sections of electronic transitions. Recently, it has been shown to be particularly suited for the detection and identification of chromophores at low concentrations and in the presence of spectral crosstalk. However, despite its low quantum yield per pulse sequence, we believe the technique has potential for selective photochemical transformations. There are some cases (e.g., the selective excitation of optogenetic switches) where the low yield may be overcome by repeated excitations to build up biochemically relevant concentrations. Here we show that double resonance excitation using general, non-resonant Raman pre-excitation is a viable candidate for selectively promoting molecules to chemically active energy levels. Further, the use of non-resonant Raman pre-excitation is less constraining than resonant Raman (used in previous double resonance microscopy works) since the choice of Raman pump-Stokes frequencies may be rather freely chosen.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Small Molecule Inhibitor-Modulated Al 2 O 3 Atomic Layer Deposition on Monolayer MoS 2 for Controlled Nucleation

The integration of ultrathin dielectrics on two-dimensional (2D) semiconductors is essential for advancing beyond-Si electronics. However, the intrinsic inertness of van der Waals 2D basal planes remains a primary bottleneck to achieving uniform dielectric nucleation and growth. Here, in this study, we introduce a small molecule inhibitor (SMI)-modulated thermal atomic layer deposition (ALD) strategy, exemplified by aluminum oxide (Al 2 O 3 ) ALD on monolayer molybdenum disulfide (1L MoS 2 ) with acetic acid (HAc) SMI. The ABC-type sequence comprises HAc inhibitor (A), trimethylaluminum (TMA) precursor (B), and deionized H 2 O coreactant (C). In situ quartz crystal microbalance (QCM) studies reveal robust HAc adsorption on Al 2 O 3 and suppression of subsequent oxide growth on HAc-passivated surfaces. When applied to 1L MoS 2 , this inhibitory pathway enables HAc to selectively passivate nascent Al 2 O 3 nuclei formed on the MoS 2 surface, limiting their three-dimensional (3D) island coarsening and redirecting precursor adsorption toward the uncovered basal plane. Consequently, nearly continuous ultrathin (∼1.5 nm) Al 2 O 3 films are achieved on 1L MoS 2 with markedly improved uniformity compared to standard Al 2 O 3 ALD using TMA and H 2 O, as validated by atomic force microscopy (AFM), cross-sectional scanning transmission electron microscopy (STEM), and energy-dispersive X-ray spectroscopy (EDS). Density functional theory (DFT) calculations further provide atomistic insight into HAc-modulated Al 2 O 3 nucleation, corroborating the energetic preference of HAc for Al 2 O 3 over MoS 2 and attenuated TMA adsorption on HAc-passivated surfaces. Spatially resolved Raman spectroscopy also confirms that the HAc-modulated process preserves the structural integrity of 1L MoS 2 , with only minimal strain and doping perturbations observed after dielectric deposition. This SMI-modulated approach offers a broadly applicable framework for controlling ALD nucleation across various inhibitors, ALD chemistries, and 2D materials, opening opportunities for reliable dielectric integration in next-generation nanoelectronics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Recombination of Hydrogen in the Iodine Reactors

The H-Canyon facility is currently dissolving spent nuclear fuel, including Material Test Reactor (MTR) and High Flux Isotope Reactor (HFIR) fuel. Dissolution of aluminum spent nuclear fuel produces hydrogen and other NOx gases. A theory long held by H-Canyon Engineering and Facility Technical Advisors that the silver nitrate-coated berl saddles, present in the iodine reactor, used for off-gas treatment were acting as a catalytic hydrogen recombiner was captured during an external review of the Accelerated Basin Deinventory program. Results from a separate SRNL project using a Raman Spectrometer to monitor the offgas from the dissolution process indicated a lack of the expected hydrogen in the off-gas stream. To test this hypothesis, a laboratory scale iodine reactor was assembled and filled with silver nitrate-coated berl saddles. Testing with this laboratory scale reactor confirmed the recombination of hydrogen when a simulated dissolver off-gas was passed through the reactor containing silver nitrate-coated berl saddles at 173-188 °C. Control experiments performed with uncoated berl saddles resulted in no change to the hydrogen concentration after passing through the reactor. The residence time of the gas in the reactor was varied to determine if residence time had an impact on the amount of hydrogen recombination occurring. Results from these experiments indicated that at the shortest residence times tested (~5 seconds) recombination of the hydrogen still exceeded 90%; however, the percent recombination did increase at longer residence times, reaching 97.9% or greater for residence times over 10 seconds. Finally, testing performed with a simplified off-gas composition containing only hydrogen and air gave similar results, indicating that the presence of NO and N 2 O gases in the stream do not play a role in the recombination reaction.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Abstract for CRADA between NETL and Praxair Surface Technologies, Inc. (AGMT-1288)

The National Energy Technology Laboratory (NETL) and Praxair Surface Technologies (Participant) will collaborate in the design and manufacturing of new high-performance thermal barrier coatings (TBCs) for hydrogen gas turbine applications. High-throughput first-principles density functional theory (DFT) calculations will be performed to accelerate novel TBCs discovery with expanded phase field, increased temperature and erosion capabilities, low thermal conductivity, and significant toughness imparted by ferroelastic toughening for the non-transformable tetragonal oxide phase. Down-selected materials will be manufactured using solid state powder processing techniques. Testing will include isothermal aging followed by Raman and x-ray diffraction (XRD) phase analysis, indentation fracture toughness measurements, erosion testing, and thermal conductivity measurements. The collaboration will facilitate the deployment of hydrogen gas turbine technologies that are a key to the decarburization of power generation in the United States.

08 HYDROGEN↗
DOE OSTI2025

Probing Surface/Bulk Structural Chemistry of Key Components of Solid Oxide Electrochemical Cells with In Situ / Operando Raman Spectroscopy

The remarkable attributes of solid oxide electrochemical cell technology (e.g., energy efficiency, low cost, scalability, low emissions, and operational flexibility, etc.) drive the wider adoption of electrochemical conversion routes for sustainability. It is critical for the codevelopment of solid oxide cell materials and processes to establish the mechanistic understanding of the underlying chemical phenomena at the molecular level. Herein, we summarize the advancements in Raman spectroscopy that provide structural/molecular information on electrode/electrolyte materials typically used in solid oxide cells for energy conversion. In particular, we discuss the multifactorial environment induced chemical processes that govern the performance and longevity of solid oxide electrochemical devices. The in situ/operando Raman spectroscopic investigations on the electrode/electrolyte materials reported in the literature are summarized with the emphasis on identification of key material properties that control the functional aspects of the solid oxide cells. The molecular level understanding of the electrochemical processes will allow advancement of the rational design of electrochemical materials for process level deployment of solid oxide cell technology.

Electrodes↗
DOE OSTI2021

Steep sulfur gradient in CZTSSe solar cells by H 2 S-assisted rapid surface sulfurization

Sulfur/selenium grading is a widely used optimization strategy in kesterite thin-film solar cells to obtain a bandgap-graded absorber material and to optimize optical and electrical properties of the solar-cell device. In this work, we present a novel approach to introduce a [S]/([S] + [Se]) grading for Cu 2 ZnSn(S,Se) 4 solar cells. In contrast to commonly used methods with slow process dynamics, the presented approach aims to create a fast sulfurization reaction on the surface of pure selenide kesterite absorbers by using highly reactive H 2 S gas and high sulfurization temperatures in a rapid flash-type process. With a combination of X-ray photoelectron spectroscopy, X-ray emission spectroscopy, Raman spectroscopy, and Raman-shallow angle cross sections spectroscopy, we gain depth-varied information on the [S]/([S] + [Se]) ratio and discuss the impact of different process parameter variations on the material and device properties. The results demonstrate the potential of the developed process to generate a steep gradient of sulfur that is confined mainly to the surface region of the absorber film.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

In Situ High-Temperature Raman Spectroscopy of UCl 3 : A Combined Experimental and Theoretical Study

Uranium trichloride (UCl 3 ) has received growing interest for its use in uranium-fueled molten salt reactors and in the pyrochemical processing of used fuel. In this paper, we report for the first time the experimentally determined Raman spectra of UCl 3 , at both ambient condition and in situ high temperatures up to 871 K. The frequencies of five of the Raman-active vibrational modes (v i ) of UCl 3 exhibit a negative temperature derivative ((∂ν i /∂T) P ) with increasing temperature. Here, this red-shift behavior is likely due to the elongation of U–Cl bonds. The average isobaric mode Grüneisen parameter (γ iP = 0.91 ± 0.02) of UCl 3 was determined through use of the coefficient of thermal expansion published in Vogel et al. (2021) and the (∂ νi /∂T) P values determined in this study. These results are in general agreement with those calculated here by density functional theory (DFT+U). Finally, a comparison of the ambient band positions of UCl 3 to those of isostructural lanthanide (La–Eu) and actinide chlorides (Am–Cf) has been made.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Chemical characterization of microplastic particles formed in airborne waste discharged from sewer pipe repairs

Microplastic particles are of increasing environmental concern due to the widespread uncontrolled degradation of various commercial products made of plastic and their associated waste disposal. Recently, common technology used to repair sewer pipes was reported as one of the emission sources of airborne microplastics in urban areas. This research presents results of the multi-modal comprehensive chemical characterization of the microplastic particles related to waste discharged in the pipe repair process and compares particle composition with the components of uncured resin and cured plastic composite used in the process. Analysis of these materials employs complementary use of surface-enhanced Raman spectroscopy, scanning transmission X-ray spectro-microscopy, single particle mass spectrometry, and direct analysis in real-time high-resolution mass spectrometry. Further, it is shown that the composition of the relatively large (100 μm) microplastic particles resembles components of plastic material used in the process. In contrast, the composition of the smaller (micrometer and sub-micrometer) particles is significantly different, suggesting their formation from unintended polymerization of water-soluble components occurring in drying droplets of the air-discharged waste. In addition, resin material type influences the composition of released microplastic particles. Results are further discussed to guide the detection and advanced characterization of airborne microplastics in future field and laboratory studies pertaining to sewer pipe repair technology.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Raman Microscopy Investigation of GLP-1 Peptide Association with Supported Phospholipid Bilayers

A wide range of important biological processes occur at phospholipid membranes including cell signaling, where a peptide or small molecule targets a membrane-localized receptor protein. In this work, we report the adaptation of confocal-Raman microscopy to quantify populations of unlabeled glucagon-like peptide-1 (GLP-1), a membrane-active 30-residue incretin peptide, in supported phospholipid bilayers deposited on the interior surfaces of wide-pore porous silica particles. Quantification of lipid bilayer-associated peptide is achieved by measuring the Raman scattering intensity of the peptide relative to that of the supported-lipid bilayer, which serves as an internal standard. The dependence of the bilayer-associated GLP-1 population on the solution-concentration of GLP-1 produces an isotherm used to determine the equilibrium constant for peptide-bilayer association and the maximum peptide surface coverage. The maximum coverage of GLP-1 in the lipid bilayer was found to be only 1/5th of a full monolayer based on its hydrodynamic radius. The saturation coverage, therefore, is not limited by the size of GLP-1 but by the ability of the bilayer to accommodate the peptide at high concentrations within the bilayer. Raman spectra show that GLP-1 association with the supported bilayer is accompanied by structural changes consistent with the intercalation of the peptide into bilayer, where the observed increase in acyl-chain order would increase the lipid density and provide free volume needed to accommodate the peptide. Furthermore, these results were compared with previous measurements of the association of fluorescently-labeled GLP-1 with a planar-supported bilayer; the unlabeled peptide exhibits a 3-fold greater affinity for the lipid-bilayer on the porous-silica support suggesting that the fluorescent label alters GLP-1 lipid-bilayer association.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Multimodal Imaging of Autofluorescent Sites Reveals Varied Chemical Speciation in SSZ-13 Crystals

Here, a multimodal imaging study of chabazite is used to show the distribution of and discriminate between different emissive deposits arising as a result of the detemplation process. 3D confocal imaging, fluorescence lifetime imaging, spectral imaging, and Raman mapping are used to show three different types of emissive behaviours each characterised by different spatial distributions, trends in lifetime, spectral signals, and Raman signatures. A notable difference is seen in the morphology of agglomerated surface deposits and larger subsurface deposits, which experience lifetime augmentation due to spatial confinement. The distribution of organic residue throughout the crystal volume is comparable to XRF mapping that shows Si enrichment on the outer edges and higher Al content through the centre, demonstrating that a fluorescence-based technique can also be used to indirectly comment on the compositional chemistry of the inorganic framework.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Investigation of poly(phenylacetylene) derivatives for carbon precursor with high carbon yield and good solubility

This paper investigates a family of poly(phenylacetylene) derivatives with a p-electrons conjugated polymer backbone and side groups containing only sp 2 and sp carbons. The objective is to identify the suitable carbon precursor that is processible and can be transformed to carbonaceous material with high carbon yield by a simple (one-step) thermal transformation process (without any external reagent). Poly(phenylacetylene) with para-substituted acetylene group poly(PA-A) shows an exceptionally high C-yield (~90%) in one-step heating from ambient temperature to 1000 °C under N 2 atmosphere. Unfortunately, this poly(PA-A) polymer is quite sensitive to heat and light with very limited solubility. On the other hand, poly(phenylacetylene) with para-substituted phenylacetylene group, i.e. poly(PA-PA), offers a relatively high C-yield (~80%) and also good solubility in common organic solvents, such as toluene and tetrahydrofuran (THF). Several uniform dark-red poly(PA-PA) fibers with smooth surface and fiber diameter in the range of 3–6 μm were prepared from 30 wt% poly(PA-PA)/THF solution using electrospinning technique. Furthermore, the resulting precursor fibers were converted to the corresponding carbon structure in a one-step thermal heating process under N 2 atmosphere. Both X-ray and Raman spectra show the polymorphous carbon morphology with the graphene crystalline domains.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Flash Graphene from Plastic Waste

In this work, an approach to upcycling plastic waste (PW) products is presented. The method relies on flash Joule heating (FJH) to convert PW into flash graphene (FG). In addition to FG, the process results in the formation of carbon oligomers, hydrogen, and light hydrocarbons. In order to make high quality graphene, a sequential alternating current (AC) and direct current (DC) flash is used. Here, the FJH process requires no catalyst and works for PW mixtures, which makes the process suitable for handling landfill PW. The energy required to convert PW to FG is ~ 23 kJ/g or ~ $125 in electricity per ton of PW, potentially making this process economically attractive for scale-up. The FG was characterized by Raman spectroscopy and had a I 2D /I G peak ratio up to 6 with a low-intensity D band. Moreover, transmission electron microscopy and X-ray diffraction analysis show that the FG is turbostratic with an interlayer spacing of 3.45 Å. The large interlayer spacing will facilitate its dispersion in liquids and composites. Analysis of FG dispersions in 1% Pluronic aqueous solution shows that concentrations up to 1.2 mg/mL can be achieved. The carbon oligomers that distilled from the process were characterized by Fourier-transform infrared spectroscopy and have chemical structures similar to the starting PW. Initial analysis of gas phase products shows the formation of considerable amounts of hydrogen along with other light hydrocarbons. Since graphene is naturally occurring and it shows a low toxicity profile, this could be an environmentally beneficial method to upcycle PE.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Insights into the Electrochemical Oxidation and Reduction of Nickel Oxide Surfaces

Surface oxidation/reduction processes, driven by varying electrochemical potentials, can substantially impact catalyst effectiveness and, consequently, electrolyzer performance. Here, this study combines theoretical and experimental approaches to explore the surface redox behavior of nickel oxides, which are cost-effective and efficient catalysts for many electrochemical reactions. Surface Pourbaix diagrams for three different phases of nickel oxides, i.e., nickel hydroxide (Ni(OH) 2 ), nickel oxyhydroxide (NiOOH), and nickel dioxide (NiO 2 ), were constructed using density functional theory-based simulations. Various experimental methods, including cyclic voltammetry, in situ Raman spectroscopy, and electrochemical titration, were employed to probe the surface redox processes of nickel oxide thin films. Our findings indicate that the ABAB stacking sequence of Ni(OH) 2 lacks stability under oxidizing conditions to host the surface oxidation (deprotonation) events, while the AABBCC stacking sequence of NiOOH is energetically favorable due to the presence of interlayer hydrogen bonding. Rapid charge transfer facilitated by interlayer hydrogen bonding accounts for the higher reactivity of partially oxidized/reduced NiOOH (001) surfaces compared to Ni(OH) 2 (001) and NiO 2 (001) surfaces with the same stoichiometry, where interlayer hydrogen bonding is absent. Insights presented in this work can offer guidelines for optimizing operational conditions and tailoring the surface structures and oxidation states of nickel oxides to enhance performance in applications such as electrocatalysis and supercapacitors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Experimental and Theoretical Studies of the Surface Oxidation Process of Rare–Earth Tritellurides

Recent studies have established Van der Waals (vdW) layered and 2D rare-earth tritellurides (RTe 3 ) as superconductors and near room-temperature charge density wave (CDW) materials. Their environmental stability raises natural concern owing to aging/stability effects observed in other tellurium-based layered crystals. Here, the results establish the stability and environmental aging characteristics of these RTe 3 systems involving a variety of metals such as La, Nd, Sm, Gd, Dy, and Ho. The atomic force microscopy (AFM) and scanning electron microscopy (SEM) results show that all the RTe 3 sheets oxidize to form thin TeO x layers that are primarily confined to the surface, edges, and grain boundaries. Time-resolved in situ Raman spectroscopy measurements are used to understand the kinetics of the oxidization process for different lanthanide metal cations and establish their relative stability/resilience to oxidization. Overall results indicate that the vdW layers show higher air stability as the 4f electron number decreases going from Ho to La, resulting in the most stable LaTe 3 compared to the least stable HoTe 3 . Comprehensive quantum mechanical simulations reveal that environmental degradation originates from a strong oxidizing reaction with O 2 molecules, while humidity (H 2 O) plays a negligible role unless Te vacancies are present. Moreover, the simulations explain the effects of 4f electrons on the work function and Te vacancies formation, which directly impact the aging characteristics of RTe 3 layers. Interestingly, optical and electrical measurements show that the CDW response is still observed in aged RTe 3 layers owing to the presence of underlying pristine/nonoxidized RTe 3 layers, except CDW transition temperatures increase due to the thickness effect. Overall results offer the first in-depth environmental aging studies on these materials, which can be applied to engineer and design their chemical stability, surface properties, and overall CDW characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Spontaneous Raman–LIF–CO–OH measurements of species concentration in turbulent spray flames

This paper presents new measurements of species concentrations, temperature and mixture fraction in selected regions of a turbulent ethanol spray flame. The line-Raman–LIF–COsingle bondOH setup developed at the Sandia's Combustion Research Facility is utilised to probe regions of a spray flame where laser breakdown of liquid droplets is avoided and the remaining interferences can be corrected. The spray flame is stabilised on the piloted Sydney needle spray burner, where axial translation of the liquid injecting needle in the air-blast stream can transition the spray from dilute to dense. The solution to obtaining successful measurements is found to be multifaceted and includes: the appropriate selection of flame conditions; high sensitivity of the Raman detection system permitting reduced laser energies; development of a pre-processing algorithm to reject strong droplet interferences; and application of the hybrid matrix inversion method combined with wavelet denoising to account for interference corrections and noise at the very low signal levels obtained. Unique and necessary for the successful measurements reported in this paper, a pre-processing algorithm is outlined that removes data points corrupted with strong interferences from droplets. These interferences arise from a range of sources, but the most intense are due to the laser interaction with surrounding mist or liquid fragments, such that measurements near the jet centreline are corrupted and hence discarded. Reliable measurements of mixture fraction, temperature obtained from the sum of the species number densities, and species mole fractions are reported for regions in the flames sufficiently far from the centreline. The paper demonstrates the feasibility of the judicious use of Raman scattering in turbulent spray flames, the results of which will be extremely useful for validating numerical simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Impact of Surface Enhanced Raman Spectroscopy in Catalysis

Catalysis stands as an indispensable cornerstone of modern society, underpinning the production of over 80% of manufactured goods and driving over 90% of industrial chemical processes. As the demand for more efficient and sustainable processes grows, better catalysts are needed. Understanding the working principles of catalysts is key, and over the last 50 years, surface-enhanced Raman Spectroscopy (SERS) has become essential. Discovered in 1974, SERS has evolved into a mature and powerful analytical tool, transforming the way in which we detect molecules across disciplines. In catalysis, SERS has enabled insights into dynamic surface phenomena, facilitating the monitoring of the catalyst structure, adsorbate interactions, and reaction kinetics at very high spatial and temporal resolutions. This review explores the achievements as well as the future potential of SERS in the field of catalysis and energy conversion, thereby highlighting its role in advancing these critical areas of research.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗