SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Internal flow performance of fixed 14 deg ramp inlet from zero to 20 deg angle of attack at supersonic free stream
Variable density hypervelocity wind tunnel tests on effects of several ramp-fairing, umbilical, and pad configurations on aerodynamic heating to Apollo command module
Initial mercury-flow ramp rates for SNAP-8 power system by transient tests
Two inlet performance tests and one inlet/airframe drag test were conducted in 1969 at the NASA-Ames Research Center. The basic inlet system was two-dimensional, three ramp (overhead), external compression, with variable capture area. The data from these tests were analyzed to show the effects of selected design variables on the performance of this type of inlet system. The inlet design variables investigated include inlet bleed, bypass, operating mass flow ratio, inlet geometry, and variable capture area.
Digital "fader" or "ramp shaper" circuits replace linear filters in suppressing switching transients and instabilities within servocontrol systems. Circuits can be optimized to introduce no attenuation, transport delay, or phase lags in new output signal.
For efficiency and convenience the voltage applied to a Si solar cell is often fairly rapidly driven from zero to the open circuit value typically at a common rate of 1 V per millisecond. During this time the values of current are determined as a function of the instantaneous voltage thus producing an I-V characteristic. The present paper shows that the customary expressions for the current as a function of cell parameters still remain valid provided that the diffusion length in the expression for the dark current is changed from its steady state value L to the effective diffusion length L1 given by L1 = L(1 + qV/kT.tau) to the -1/2, where V is the ramp rate considered constant and tau is the lifetime of minority carriers. This result is true to a very good approximation provided that low level injection prevails.
Simple modification to bootstrap ramp generator gives more linear output over longer sweep times. New circuit adds just two resistors, one of which is adjustable. Modification cancels nonlinearities due to variations in load on charging capacitor and due to changes in charging current as the voltage across capacitor increases.
The effects of geometric design parameters on the internal performance of nonaxisymmetric single expansion-ramp nozzles were investigated at nozzle pressure ratios up to approximately 10. Forward-flight (cruise), vectored-thrust, and reversed-thrust nozzle operating modes were investigated.
A penetration apparatus, for very high temperature applications in which a base plug is inserted into an opening through a bulkhead is described. The base plug has a head shape and is seated against the highest temperature surface of the bulkhead, which may be the skin of the nose cone or other part of a space vehicle intended for nondestructive atmospheric reentry. From the second side of the bulkhead at which the less severe environment is extant, a bayonet plug is inserted into the base plug and engages an internal shoulder at about 90 deg rotation. The bayonet plug has an integral flanged portion and a pair of ramping washers which are located between the flange and the second bulkhead surface with a spacing washer as necessary.
The Langley 16 foot transonic tunnel was used to determine the aeropropulsive characteristics of twin single-expansion-ramp vectoring nozzles installed in a wing-body configuration with forward-swept wings. The configuration was tested with and without fixed canards. The test conditions included free-stream Mach numbers of 0.60, 0.90, and 1.20. The model angle of attack ranged from -2 deg to 14 deg; the nozzle pressure ratio ranged from 1.0 (jet off) to 9.0. The Reynolds number based on the wing mean aerodynamic chord varied from 3.0 x 10 to the 6th power to 4.8 x 10 to the 6th power, depending on Mach number. Aerodynamic characteristics were analyzed to determine the effects of thrust vectoring and the canard effects on the wing-afterbody-nozzle and the wing-afterbody portions of the model. Thrust vectoring had no effect on the angle of attack for the onset of flow separation on the wing but resulted in reduced drag at angle-of-attack values above that required for wing flow separation. The canard was found to have little effect on the thrust-induced lift resulting from vectoring, since canard effects occurred primarily on the wing.
A procedure that allows rapid preliminary evaluations of the vertical, short, and normal takeoff performance of supersonic cruise aircraft concepts was developed into a numerical computer program. The program is used to determine the effects on takeoff performance of various parameters, such as thrust-weight ratio, wing loading, thrust vector angle, and flap setting. Ramp-assisted takeoffs for overloaded configurations typical of a ground-attack mission are included. The effects of wind on the takeoff performance are also considered.
The analysis of a proposed new technique for capacitance type blade tip clearance measurement is presented. The capacitance between the blade tip and a mounted capacitance electrode within a guard ring forms one of the feedback elements of a high speed operational amplifier. The differential equation governing the operational amplifier circuit is formulated and solved for two types of inputs to the amplifier - a constant voltage and a ramp. The resultant solutions shows an output that contains a term that is proportional to the derivative of the product of the input voltage and the time constant of the feedback network. The blade tip clearance capacitance is obtained by subtracting the output of a balancing reference channel followed by integration. The proposed sampled data algorithm corrects the environmental effects and varying rotor speeds on-line, making the system suitable for turbine instrumentation. System requirements, block diagrams, and typical application are included.
The analysis of a proposed new technique for capacitance type blade tip clearance measurement is presented. The capacitance between the blade tip and a mounted capacitance electrode within a guard ring forms one of the feedback elements of a high speed operational amplifier. The differential equation governing the operational amplifier circuit is formulated and solved for two types of inputs to the amplifier - a constant voltage and a ramp. The resultant solution shows an output that contains a term that is proportional to the derivative of the product of the input voltage and the time constant of the feedback network. The blade tip clearance capacitance is obtained by subtracting the output of a balancing reference channel followed by integration. The proposed sampled data algorithm corrects for environmental effects and varying rotor speeds on-line, making the system suitable for turbine instrumentation. System requirements, block diagrams, and a typical application are included.
In conjunction with new experimental results at Mach 5, an examination has been made of published data on unsteadiness of shock-induced turbulent boundary-layer separation. The data are all wall pressure fluctuation measurements made under the unsteady separation shock and are from interactions induced by compression ramps, blunt and sharp fins, and circular cylinders. There is little evidence of a link between the separation shock zero-crossing frequency and characteristic frequency of the incoming boundary layer. The low shock frequencies and low shock speeds, and the trends with changes in model geometric parameters and incoming boundary layer, suggest that turbulent or global fluctuations at the upstream boundary of the separated flow drive the shock motion.
Separation control experiments were conducted in a 51-71-cm shear-flow control tunnel using a backward-facing ramp to investigate the performance of transverse and swept grooves for controlling a two-dimensional turbulent separated flow at low speeds and moderate Reynolds numbers. In the experiments, transverse grooves, located in the maximum +dP/dx region, with a height-to-width ratio greater than 2.5, reduced the reattachment distance by 20 percent over the baseline configuration. Unlike transverse and longitudinal grooves of equivalent size, the 45-degree swept-groove configurations tested enhanced separation.
An implicit, finite-difference, upwind, full Navier-Stokes solver was applied to supersonic/hypersonic flows over two-dimensional ramps and three-dimensional obstacle. Some of the computed results are presented. The numerical scheme used in the study is an implicit, spacially second order accurate, upwind, LU-ADI scheme based on Roe's approximate Reimann solver with MUSCL differencing of Van Leer. An algebraic grid generation scheme based on generalized interpolation scheme was used in generating the grids for the various 2-D and 3-D problems.
The single-expansion-ramp-nozzle (SERN) experiment underway at NASA Ames Research Center simulates the National Aerospace Plane propulsive jet-plume flow. Recently, limited experimental data has become available from an experiment with a generic nozzle/afterbody model in a hypersonic wind tunnel. The present paper presents full three-dimensional solutions obtained with the implicit Navier-Stokes solver, FL3D, for the baseline model and a version of the model with side extensions. Analysis of the computed flow clearly shows the complex 3-D nature of the flow, critical flow features, and the effect of side extensions on the plume flow development. Flow schematics appropriate for the conditions tested are presented for the baseline model and the model with side extensions. The computed results show excellent agreement with experimental shadowgraph and with surface pressure measurements. The computed and experimental surface oil-flows show the same features but may be improved by appropriate turbulence modeling.
An implicit, finite-difference, upwind, full Navier-Stokes solver was applied to supersonic/hypersonic flows over two-dimensional ramps and three-dimensional obstacle. Some of the computed results are presented. The numerical scheme used in the study is an implicit, spatially second order accurate, upwind, LU-ADI scheme based on Roe's approximate Reimann solver with MUSCL differencing of Van Leer. An algebraic grid generation scheme based on generalized interpolation scheme was used in generating the grids for the various 2-D and 3-D problems.