Search NASA⌕ Search

SEARCH · Search NASA

Results for “SAR Systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Analysis and an image recovery algorithm for ultrasonic tomography system

The problem of an ultrasonic reflectivity tomography is similar to that of a spotlight-mode aircraft Synthetic Aperture Radar (SAR) system. The analysis for a circular path spotlight mode SAR in this paper leads to the insight of the system characteristics. It indicates that such a system when operated in a wide bandwidth is capable of achieving the ultimate resolution; one quarter of the wavelength of the carrier frequency. An efficient processing algorithm based on the exact two dimensional spectrum is presented. The results of simulation indicate that the impulse responses meet the predicted resolution performance. Compared to an algorithm previously developed for the ultrasonic reflectivity tomography, the throughput rate of this algorithm is about ten times higher.

Jin, Michael Y.↗

A system concept for wide swath constant incident angle coverage

The multiple beam SAR system concept is developed and shown to readily overcome the radar ambiguity constraints associated with orbital systems, thus permitting imagery over swaths much wider than 100 km. The antenna technique permits imagery at nearly constant incidence angles. When frequency scanning is used, the center angle may be programmed. The redundant use of the antenna aperture during reception results in lower transmitted power and in shorter antenna lengths in comparison with conventional designs.

Claassen, J. P.↗

Advanced synthetic aperture radar for remote sensing

A program initiated by NASA was formed to address some key earth resources synthetic aperture radar (SAR) needs. Major steps in the SAR system development are summarized, and the objective of the advanced SAR (ASAR) program is defined. The program rationale and specific objectives are discussed, including system calibration, wide-band technique evaluation, a system resolution of 10 m or better at 45 deg, and an airborne system to cover four bands within 1 to 10 GHz. The ASAR conceptual system design, consisting of a modulator, transmitter, antenna, receiver, calibrator, and data system modules is also presented, and ASAR capability expansions are discussed. The program, scheduled for 1983, will provide a data source which is not available to applications investigations at this time, and will produce design approaches that are flexible and multimission to the maximum extent for application to a Shuttle or a freeflyer system.

Krishen, K.↗

Pipelined digital SAR azimuth correlator using hybrid FFT-transversal filter

A synthetic aperture radar system (SAR) having a range correlator is provided with a hybrid azimuth correlator which utilizes a block-pipe-lined fast Fourier transform (FFT). The correlator has a predetermined FFT transform size with delay elements for delaying SAR range correlated data so as to embed in the Fourier transform operation a corner-turning function as the range correlated SAR data is converted from the time domain to a frequency domain. The azimuth correlator is comprised of a transversal filter to receive the SAR data in the frequency domain, a generator for range migration compensation and azimuth reference functions, and an azimuth reference multiplier for correlation of the SAR data. Following the transversal filter is a block-pipelined inverse FFT used to restore azimuth correlated data in the frequency domain to the time domain for imaging.

Wu, C.↗

Radar systems for the water resources mission, volume 2

The application of synthetic aperture radar (SAR) in monitoring and managing earth resources was examined. The function of spaceborne radar is to provide maps and map imagery to be used for earth resource and oceanographic applications. Spaceborne radar has the capability of mapping the entire United States regardless of inclement weather; however, the imagery must have a high degree of resolution to be meaningful. Attaining this resolution is possible with the SAR system. Imagery of the required quality must first meet mission parameters in the following areas: antenna patterns, azimuth and range ambiguities, coverage, and angle of incidence.

Moore, R. K.↗

A Dual Polarization, Active, Microstrip Antenna for an Orbital Imaging Radar System Operating at L-Band

A highly successful Earth orbiting synthetic antenna aperture radar (SAR) system, known as the SIR-C mission, was carried into orbit in 1994 on a U.S. Shuttle (Space Transportation System) mission. The radar system was mounted in the cargo bay with no need to fold, or in any other way reduce the size of the antennas for launch. Weight and size were not limited for the L-Band, C-Band, and X-Band radar systems of the SIR-C radar imaging mission; the set of antennas weighed 10,500 kg, the L-Band antenna having the major share of the weight. This paper treats designing an L-Band antenna functionally similar to that used for SIR-C, but at a fraction of the cost and at a weight in the order of 250 kg. Further, the antenna must be folded to fit into the small payload shroud of low cost booster rocket systems. Over 31 square meters of antenna area is required. This low weight, foldable, electronic scanning antenna is for the proposed LightSAR radar system which is to be placed in Earth orbit on a small, dedicated space craft at the lowest possible cost for an efficient L- Band radar imaging system. This LightSAR spacecraft radar is to be continuously available for at least five operational years, and have the ability to map or repeat-map any area on earth within a few days of any request. A microstrip patch array, with microstrip transmission lines heavily employed in the aperture and in the corporate feed network, was chosen as the low cost approach for this active dual-polarization, 80 MHz (6.4%) bandwidth antenna design.

Kelly, Kenneth C.↗

A Dual Polarization, Active, Microstrip Antenna for an Orbital Imaging Radar System Operating at L-Band

A highly successful Earth orbiting synthetic antenna aperture radar (SAR) system, known as the SIR-C mission, was carried into orbit in 1994 on a U.S. Shuttle (Space Transportation System) mission. The radar system was mounted in the cargo bay with no need to fold, or in any other way reduce the size of the antennas for launch. Weight and size were not limited for the L-Band, C-Band, and X-Band radar systems of the SIR-C radar imaging mission; the set of antennas weighed 10,500 kg, the L-Band antenna having the major share of the weight. This paper treats designing an L-Band antenna functionally similar to that used for SIR-C, but at a fraction of the cost and at a weight in the order of 250 kg. Further, the antenna must be folded to fit into the small payload shroud of low cost booster rocket systems. Over 31 square meters of antenna area is required. This low weight, foldable, electronic scanning antenna is for the proposed LightSAR radar system which is to be placed in Earth orbit on a small, dedicated space craft at the lowest possible cost for an efficient L-Band radar imaging system. This LightSAR spacecraft radar is to be continuously available for at least five operational years, and have the ability to map or repeat-map any area on earth within a few days of any request. A microstrip patch array, with microstrip transmission lines heavily employed in the aperture and in the corporate feed network, was chosen as the low cost approach for this active dual-polarization, 80 MHz (6.4%) bandwidth antenna design.

Kelly, Kenneth C.↗

FIREX mission requirements document for renewable resources

The initial experimental program and mission requirements for a satellite synthetic aperture radar (SAR) system FIREX (Free-Flying Imaging Radar Experiment) for renewable resources is described. The spacecraft SAR is a C-band and L-band VV polarized system operating at two angles of incidence which is designated as a research instrument for crop identification, crop canopy condition assessments, soil moisture condition estimation, forestry type and condition assessments, snow water equivalent and snow wetness assessments, wetland and coastal land type identification and mapping, flood extent mapping, and assessment of drainage characteristics of watersheds for water resources applications. Specific mission design issues such as the preferred incidence angles for vegetation canopy measurements and the utility of a dual frequency (L and C-band) or dual polarization system as compared to the baseline system are addressed.

Carsey, F.↗

Remote Sensing of Antarctic Sea Ice with Coordinated Aircraft and Satellite Data Acquisitions

Remote sensing of Antarctic sea ice is required to characterize properties of the vast sea ice cover to understand its long-term increase in contrast to the decrease of Arctic sea ice. For this objective, the OIB/TanDEM-X Coordinated Science Campaign (OTASC) was successfully conducted in 2017 to obtain contemporaneous and collocated remote sensing data from NASA's Operation IceBridge (OIB) and the German Aerospace Center (DLR) TanDEM-X Synthetic Aperture Radar (SAR) system at X-band together with Sentinel-1 and RADARSAT-2 SARs at C-band in conjunction with WorldView satellite spectral sensors, surface measurements, and field observations. The Weddell Sea and the Ross Sea were two primary regions while SAR data were also collected over six other regions in the Southern Ocean. Satellite SAR data included both polarimetric and interferometric capabilities to infer snow and sea ice information in three dimensions (3D), while OIB/P-3 aircraft data include snow radar together with altimeter data for snow and sea ice observations in 3D over the Weddell Sea. Across the Ross Sea, IcePOD and AntNZ/York-University flights were carried out together with satellite SAR data acquisitions.

OIB↗

A Proof for the Unbiased Nature of Range-Doppler Measurements in Coarse-Resolution Dechirp-on-Receive Feedback Synthetic Aperture Radar Navigation

In feedback synthetic aperture radar (SAR) navigation, observables extracted from SAR range-Doppler images correct position and velocity errors accumulated within an associated navigation system. Unlike most other sensors, which produce measurements without input from a navigation system, SARs require a prior estimate of the radar’s position and velocity to adjust the radar’s matched filter during range-Doppler image formation. Consequently, it is possible for position and velocity errors within a navigation system to manifest as additional errors (biases) in the range-Doppler measurement observables. Prior work has not tackled this possibility in the context of feedback SAR navigation with a dechirp-on-receive radar. This paper offers a proof demonstrating that range-Doppler observables extracted from coarse-resolution vertical SAR images formed with a dechirp-on-receive radar may be safely modeled as unbiased measurements of the radar’s true position and velocity despite the presence of moderate navigation errors.

dechirp-on-receive↗

Design of an Ultra-High Efficiency GaN High-Power Amplifier for SAR Remote Sensing

This work describes the development of a high-power amplifier for use with a remote sensing SAR system. The amplifier is intended to meet the requirements for the Sweep-SAR technique for use in the proposed DESDynI SAR instrument. In order to optimize the amplifier design, active load-pull technique is employed to provide harmonic tuning to provide efficiency improvements. In addition, some of the techniques to overcome the challenges of load-pulling high power devices are presented. The design amplifier was measured to have 49 dBm of output power with 75% PAE, which is suitable to meet the proposed system requirements.

active load-pull↗

A novel algorithm for sea surface height estimation using complex SAR data

A method of extracting sea height information from Synthetic Aperture Radar (SAR) complex data was studied. A fundamental SAR ocean imaging model for gravity waves showed that information about the long wave is present in the SAR complex data, especially its phase. Phase demodulation algorithm followed by linear regression and filtering was employed. Only the latter two steps incorporated a priori information that might be available. A relatively simplified simulation indicated that the finite bandwidth of the SAR system imposed the apparently most serious limitation. A preliminary application to SEASAT-SAR complex imagery was encouraging. Information about the long wave, if incorporated into a more sophisticated phase demodulation structure, i.e., at an earlier point in the algorithm, could conceivably mitigate this bandwidth limitation.

Harger, R. O.↗

Real time SAR processing

A simplified model for the SAR imaging problem is presented. The model is based on the geometry of the SAR system. Using this model an expression for the entire phase history of the received SAR signal is formulated. From the phase history, it is shown that the range and the azimuth coordinates for a point target image can be obtained by processing the phase information during the intrapulse and interpulse periods respectively. An architecture for a VLSI implementation for the SAR signal processor is presented which generates images in real time. The architecture uses a small number of chips, a new correlation processor, and an efficient azimuth correlation process.

Premkumar, A. B.↗

The Effects of Noise on Polarimetric SAR Data

Polarimetric SAR data can provide a great deal of information about the scattering behavior of the surface under observation. Polarimetric SAR systems often measure the scattering matrices of the areas under observation in linear polarizations (H and V). From the scattering matrix commonly used forms such as the covariance matrix and the Stokes matrix can be easily derived. Other measures derived from polarimetric SAR data include correlation coefficients between scattering matrix terms and the mode and variance of phase differences between scattering matrix terms. The effects of additive system noise on these measurements is not often considered in the literature on this subject. In this paper, the effects of additive system noise on measurements derived from polarimetric SAR data will be examined. It will be shown how first-order noise effects can be removed and how second-order noise effects can be reduced for some measurements...

Freeman, A.↗

Analog In-Memory Computing for the Synthetic Aperture Radar Polar Format Algorithm

As the utility of synthetic aperture radar (SAR) systems increases in autonomous vehicles, satellites, and other power- and space-constrained edge applications, there is a growing need for processors that can form SAR images at low power. In recent years, analog in-memory compute (AIMC) has shown immense promise for accelerating neural networks and other matrix-vector multiplication (MVM) heavy workloads at the edge. Here, in this work, we examine how the polar format algorithm (PFA), a popular SAR image formation algorithm, can be mapped to these AIMC systems. The PFA maps readily onto analog MVMs because it primarily consists of two linear operations: interpolation of frequency-domain data to a Cartesian grid, followed by a 2-D Fourier transform. This work presents two approaches to map the interpolation operation onto MVMs in analog hardware: a chirp transform and a modified form of sinc interpolation. These mappings introduce algorithmic errors, and their effect on the quality of SAR image formation is examined, both quantitatively and qualitatively. In addition, the impact of errors introduced by the analog hardware is explored to determine which approach is optimal under varying assumptions about the underlying analog memory devices and circuits.

Analog computing↗

Seasat land experiments

An overview of the Seasat land experiments is presented. The potential roles for active microwave imaging systems on board satellites were reviewed with particular emphasis on the Seasat Synthetic Aperture Radar (SAR). Recommendations were made concerning the type of experiments that could most profitably be conducted over land with the Seasat SAR system capabilities available.

Estes, J. E.↗

Radar Technology Development at NASA/JPL

Radar at JPL and worldwide is enjoying a period of unprecedented development. JPL's science-driven program focuses on exploiting commercially available components to build new technologies to meet NASA's science goals. Investments in onboard-processing, advanced digital systems, and efficient high-power devices, point to a new generation of high-performance scientific SAR systems in the US. Partnerships are a key strategy for US missions in the coming decade

radar↗

Ionospheric Specifications for SAR Interferometry (ISSI)

The ISSI software package is designed to image the ionosphere from space by calibrating and processing polarimetric synthetic aperture radar (PolSAR) data collected from low Earth orbit satellites. Signals transmitted and received by a PolSAR are subject to the Faraday rotation effect as they traverse the magnetized ionosphere. The ISSI algorithms combine the horizontally and vertically polarized (with respect to the radar system) SAR signals to estimate Faraday rotation and ionospheric total electron content (TEC) with spatial resolutions of sub-kilometers to kilometers, and to derive radar system calibration parameters. The ISSI software package has been designed and developed to integrate the algorithms, process PolSAR data, and image as well as visualize the ionospheric measurements. A number of tests have been conducted using ISSI with PolSAR data collected from various latitude regions using the phase array-type L-band synthetic aperture radar (PALSAR) onboard Japan Aerospace Exploration Agency's Advanced Land Observing Satellite mission, and also with Global Positioning System data. These tests have demonstrated and validated SAR-derived ionospheric images and data correction algorithms.

Pi, Xiaoqing↗