Search NASA⌕ Search

SEARCH · Search NASA

Results for “SCALE MODELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Aerodynamic performance of a scale-model, counter-rotating unducted fan

The aerodynamic performance of a scale model, counter-rotating unducted fan has been determined and the results are discussed. Experimental investigations were conducted using the scale model propulsor simulator and uniquely shaped fan blades. The blades, designed for a high disk loading at Mach 0.72 at 35,000 feet altitude maximum climb condition are aft-mounted on the simulator in a pusher configuration. Data are compared with analytical predictions at the design point and show good agreement.

Sullivan, Thomas J.↗
NASA NTRS1980

Scale model studies for establishing the flow patterns of a low-speed tunnel

Experiments were conducted in a model tunnel scaled down in a ratio of 1:24 from the full size prototype V/STOL tunnel at NASA Langley Research Center. The flow characteristics around the tunnel were studied and the location and causes of local flow separation and local recirculation were documented. The study of the interaction between the various components from which the tunnel is built, an experimental setup similar to the sequence of tunnel circuit components was constructed which enabled the various components to be tested either individually or in combination. The components were tested by the simple technique of blowing air through them, then measuring the velocity distribution at relevant sections.

Barna, P. S.↗
NASA NTRS1983

Pressure distributions obtained on a 0.04-scale and 0.02-scale model of the Space Shuttle Orbiter's forward fuselage in the Langley continuous flow hypersonic tunnel

Results from pressure distribution tests on 0.04-scale and 0.02-scale models of the forward fuselage of the Space Shuttle Orbiter are presented without analysis. The tests wre completed in the Langley Continuous Flow Hypersonic Tunnel (CFHT). The 0.04-scale model was tested at angles of attack from -5 deg to 45 deg and angles of sideslip from -3 deg to 3 deg. The 0.02-scale model was tested at angles of attack from -10 deg to 45 deg and angles of sideslip from -5 deg to 5 deg. The tests were conducted in support of the development of the Shuttle Entry Air Data System (SEADS). In addition to modeling the 20 SEADS pressure orifices, the wind-tunnel models were also instrumented with orifices to match Development Flight Instrumentation (DFI) port locations currently existing on the Space Shuttle Orbiter Columbia (OV-102). This DFI simulation has provided a means for comparisons between reentry flight pressure data and wind-tunnel data.

Bradley, P. F.↗
NASA NTRS2022

The Earth Model Column Collaboratory (EMC2) v1.1: An Open-Source Ground-Based Lidar and Radar Instrument Simulator and Subcolumn Generator for Large-Scale Models

Climate models are essential for our comprehensive understanding of Earth's atmosphere and can provide critical insights on future changes decades ahead. Because of these critical roles, today's climate models are continuously being developed and evaluated using constraining observations and measurements obtained by satellites, airborne, and ground-based instruments. Instrument simulators can provide a bridge between the measured or retrieved quantities and their sampling in models and field observations while considering instrument sensitivity limitations. Here we present the Earth Model Column Collaboratory (EMC2), an open-source ground-based lidar and radar instrument simulator and subcolumn generator, specifically designed for large-scale models, in particular climate models, but also applicable to high-resolution model output. EMC2 provides a flexible framework enabling direct comparison of model output with ground-based observations, including generation of subcolumns that may statistically represent finer model spatial resolutions. In addition, EMC2 emulates ground-based (and air- or space-borne) measurements while remaining faithful to large-scale models' physical assumptions implemented in their cloud or radiation schemes. The simulator uses either single particle or bulk particle size distribution lookup tables, depending on the selected scheme approach, to perform the forward calculations. To facilitate model evaluation, EMC2 also includes three hydrometeor classification methods, namely, radar- and sounding-based cloud and precipitation detection and classification, lidar-based phase classification, and a Cloud Feedback Model Intercomparison Project Observational Simulator Package (COSP) lidar simulator emulator. The software is written in Python, is easy to use, and can be straightforwardly customized for different models, radars, and lidars. Following the description of the logic, functionality, features, and software structure of EMC2, we present a case study of highly supercooled mixed-phase cloud based on measurements from the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) West Antarctic Radiation Experiment (AWARE). We compare observations with the application of EMC2 to outputs from four configurations of the NASA Goddard Institute for Space Studies (GISS) climate model (ModelE3) in single-column model (SCM) mode and from a large-eddy simulation (LES) model. We show that two of the four ModelE3 configurations can form and maintain highly supercooled precipitating cloud for several hours, consistent with observations and LES. While our focus is on one of these ModelE3 configurations, which performed slightly better in this case study, both of these configurations and the LES results post-processed with EMC2 generally provide reasonable agreement with observed lidar and radar variables. As briefly demonstrated here, EMC2 can provide a lightweight and flexible framework for comparing the results of both large-scale and high-resolution models directly with observations, with relatively little overhead and multiple options for achieving consistency with model microphysical or radiation scheme physics.

Earth Model Column Collaboratory↗
NASA NTRS1982

An investigation of scale model testing of VTOL aircraft in hover

Utilizing the unique opportunity created by full scale hover testing of the twin-jet Grumman Design 698 VTOL aircraft in the NASA-Ames Hover Facility, a series of experiments was conducted to evaluate the effectivness of scale model testing in predicting full scale behavior. Interference forces were found to be sensitive to aircraft lower surface geometry, but when the geometry was modeled accurately the small scale results matched full scale forces guite well. The interference forces were found to be insensitive to core nozzle temperature and fan nozzle pressure ratio. The results clearly demonstrate that small scale models can be reliably utilized for aircraft and technology development when the appropriate sensitivities are recognized.

Hill, W. G., Jr.↗
NASA NTRS1983

Pressure distributions obtained on a 0.04-scale and 0.02-scale model of the Space Shuttle Orbiter's forward fuselage in the Langley 20-inch Mach 6 air tunnel

Results from pressure distribution tests on 0.04-scale and 0.02-scale models of the forward fuselage of the Space Shuttle Orbier are presented without analysis. The tests were completed in the Langley 20-Inch Mach 6 Tunnel. The 0.04-scale model was tested at angles of attack from 0 to 35 and angles of sideslip from 0 to -4. The 0.02-scale model was tested at angles of attack from -10 to 45 and angles of sideslip from 0 to -4. The tests were conducted in support of the development of the Shuttle Entry Air Data System (SEADS). In addition to modeling the 20 SEADS pressure orifices, the wind-tunnel to models were also instrumented with orifices to match Development Flight Instrumentation (DFI) port locations currently existing on the Space Shuttle Orbiter Columbia (OV-102). This DFI simulation had provided a means for comparisons between reentry flight pressure data and wind-tunnel data.

Bradley, P. F.↗
NASA NTRS1975

Results of aerothermodynamic heating tests on a 0.013-scale model solid rocket booster in the NASA/LaRC unitary plan wind tunnel (SH12F)

A 0.013 scale model of the solid rocket booster (SRB) used to launch the space shuttle was tested at a Mach number of 3.7 and Reynolds numbers of 1,500,000 and 3,500,000 per foot. The objective of the test was to obtain aerodynamic heat transfer data on the surface of scaled models of the SRB at simulated full scale reentry flight conditions. Three separate models were utilized to measure film coefficients over an angle of attack range from 0 deg to 180 deg at 0 deg sideslip. All three models were representations of the MCR0200 baseline configuration and varied only by the way they were mounted in the tunnel. Model A, sting mounted thru the model base, was utilized for testing between 0 deg and 40 deg angle of attack. Model B was blade mounted from the top of the model and was tested between 60 deg and 120 deg angle of attack. Model C was sting mounted thru the model nose and utilized for testing between 140 deg and 180 deg angle of attack.

Brewer, E. B.↗
DOE OSTI2022

The Earth Model Column Collaboratory (EMC 2 ) v1.1: an open-source ground-based lidar and radar instrument simulator and subcolumn generator for large-scale models

Abstract. Climate models are essential for our comprehensive understanding of Earth's atmosphere and can provide critical insights on future changes decades ahead. Because of these critical roles, today's climate models are continuously being developed and evaluated using constraining observations and measurements obtained by satellites, airborne, and ground-based instruments. Instrument simulators can provide a bridge between the measured or retrieved quantities and their sampling in models and field observations while considering instrument sensitivity limitations. Here we present the Earth Model Column Collaboratory (EMC2), an open-source ground-based lidar and radar instrument simulator and subcolumn generator, specifically designed for large-scale models, in particular climate models, but also applicable to high-resolution model output. EMC2 provides a flexible framework enabling direct comparison of model output with ground-based observations, including generation of subcolumns that may statistically represent finer model spatial resolutions. In addition, EMC2 emulates ground-based (and air- or space-borne) measurements while remaining faithful to large-scale models' physical assumptions implemented in their cloud or radiation schemes. The simulator uses either single particle or bulk particle size distribution lookup tables, depending on the selected scheme approach, to perform the forward calculations. To facilitate model evaluation, EMC2 also includes three hydrometeor classification methods, namely, radar- and sounding-based cloud and precipitation detection and classification, lidar-based phase classification, and a Cloud Feedback Model Intercomparison Project Observational Simulator Package (COSP) lidar simulator emulator. The software is written in Python, is easy to use, and can be straightforwardly customized for different models, radars, and lidars. Following the description of the logic, functionality, features, and software structure of EMC2, we present a case study of highly supercooled mixed-phase cloud based on measurements from the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) West Antarctic Radiation Experiment (AWARE). We compare observations with the application of EMC2 to outputs from four configurations of the NASA Goddard Institute for Space Studies (GISS) climate model (ModelE3) in single-column model (SCM) mode and from a large-eddy simulation (LES) model. We show that two of the four ModelE3 configurations can form and maintain highly supercooled precipitating cloud for several hours, consistent with observations and LES. While our focus is on one of these ModelE3 configurations, which performed slightly better in this case study, both of these configurations and the LES results post-processed with EMC2 generally provide reasonable agreement with observed lidar and radar variables. As briefly demonstrated here, EMC2 can provide a lightweight and flexible framework for comparing the results of both large-scale and high-resolution models directly with observations, with relatively little overhead and multiple options for achieving consistency with model microphysical or radiation scheme physics.

58 GEOSCIENCES↗
NASA NTRS1949

Flight Investigation of 6.25-Inch-Diameter Deacon Rocket and 10-Inch-Scale Model Rocket

Flight tests were conducted at the NACA Pilotless Aircraft Research Station, Wallops Island, to determine the characteristics of the Allegany Ballistics Laboratory's 6.2inch-diameter Deacon and lO-inch-scale model solid-propellant rocket motors. The tests were performed to assist in the development of these rockets which were designed for, and urgently needed to propel supersonic research models and pilotless aircraft. The tests showed that the rocket motors functioned properly under various flight- acceleration loads over a range of pre-ignition grain temperatures. A maximum velocity of 4180 feet per second was obtained at an elapsed time of 2.9 seconds with the 6.25-inch Deacon rocket motor at a gross weight of l9O pounds. Free-flight data of drag coefficient for the Deacon configuration for a Mach number range of 1.1 to 3.6 have been obtained from flight tests of several pounds. Camera studies of the take-off and flights of the Deacon rocket shared no evidence of breakup of propellant grains. An analysis of the forces to which the Deacon rocket grain is subjected was made. The analysis shows that the grain loading is most severe near the beginning and near the end of the rocket action time. The 10-inch-scale model rocket motor is a scaled model of the l6-inch- diameter multi-perforated, cast-grain rocket motor. A maximum velocity of 1625 feet per second at a time of 1.075 seconds was obtained at a gross weight of 309 pounds.

Watson, R. S.↗
NASA NTRS2011

Ares I Scale Model Acoustic Test Above Deck Water Sound Suppression Results

The Ares I Scale Model Acoustic Test (ASMAT) program test matrix was designed to determine the acoustic reduction for the Liftoff acoustics (LOA) environment with an above deck water sound suppression system. The scale model test can be used to quantify the effectiveness of the water suppression system as well as optimize the systems necessary for the LOA noise reduction. Several water flow rates were tested to determine which rate provides the greatest acoustic reductions. Preliminary results are presented.

Counter, Douglas D.↗
NASA NTRS1980

Aerodynamic characteristics of three helicopter rotor airfoil sections at Reynolds number from model scale to full scale at Mach numbers from 0.35 to 0.90

An investigation was conducted in the Langely 6 by 28 inch transonic tunnel to determine the two dimensional aerodynamic characteristics of three helicopter rotor airfoils at Reynolds numbers from typical model scale to full scale at Mach numbers from about 0.35 to 0.90. The model scale Reynolds numbers ranged from about 700,00 to 1,500,000 and the full scale Reynolds numbers ranged from about 3,000,000 to 6,600,000. The airfoils tested were the NACA 0012 (0 deg Tab), the SC 1095 R8, and the SC 1095. Both the SC 1095 and the SC 1095 R8 airfoils had trailing edge tabs. The results of this investigation indicate that Reynolds number effects can be significant on the maximum normal force coefficient and all drag related parameters; namely, drag at zero normal force, maximum normal force drag ratio, and drag divergence Mach number. The increments in these parameters at a given Mach number owing to the model scale to full scale Reynolds number change are different for each of the airfoils.

Noonan, K. W.↗
NASA NTRS1984

A correlation of scale model and flight aeroacoustic data for the Space Shuttle vehicle

A correlation is presented between aeroacoustic data acquired in the early Space Shuttle flights and in the various scale model tests from which the Shuttle vibroacoustic design environments were derived. These are the external acoustic data on the vehicle elements at liftoff, during the transonic and maximum dynamic pressure period of ascent flight, and during spent SRB reentry. The maximum external acoustic environment on the Shuttle elements in a given 1/3-octave frequency band comes from one of these critical flight regimes. The data correlation is seen to be good, testifying to adequate scale model measurement and test techniques. Some of the more salient features of the scale model test programs are described.

Dougherty, N. S.↗
NASA NTRS2001

Modeling and Analysis of Structural Dynamics for a One-Tenth Scale Model NGST Sunshield

New modeling and analysis techniques have been developed for predicting the dynamic behavior of the Next Generation Space Telescope (NGST) sunshield. The sunshield consists of multiple layers of pretensioned, thin-film membranes supported by deployable booms. Modeling the structural dynamic behavior of the sunshield is a challenging aspect of the problem due to the effects of membrane wrinkling. A finite element model of the sunshield was developed using an approximate engineering approach, the cable network method, to account for membrane wrinkling effects. Ground testing of a one-tenth scale model of the NGST sunshield were carried out to provide data for validating the analytical model. A series of analyses were performed to predict the behavior of the sunshield under the ground test conditions. Modal analyses were performed to predict the frequencies and mode shapes of the test article and transient response analyses were completed to simulate impulse excitation tests. Comparison was made between analytical predictions and test measurements for the dynamic behavior of the sunshield. In general, the results show good agreement with the analytical model correctly predicting the approximate frequency and mode shapes for the significant structural modes.

Johnston, John↗
DOE OSTI2025

Meso-scale modeling of UO2 nuclear fuel to high burnup

To improve the economics of light water reactors for commercial nuclear energy generation, utility operators are seeking to obtain regulatory approval to run UO2 fuel to higher levels of burnup. One potential impediment to obtaining this approval is the phenomenon of fuel fragmentation, relocation, and dispersal (FFRD). FFRD can result when fuel experiences a rapid temperature transient, such as that occurring during a Loss Of Coolant Accident (LOCA). FFRD has historically been most associated with the rim region in UO2 fuel pellets, where the phenomenon of fragmentation is also referred to as pulverization due to the small size of the fragments. More recent evidence suggests that the so-called “dark zone” (due to its appearance in micrographs) that can be observed in the mid-radial regions of high burnup fuel is also susceptible to FFRD. Although empirical fuel performance models have been developed that can adequately predict pulverization in the rim region under typical LWR conditions, a scientific understanding of what underlies fuel restructuring and subsequent FFRD is lacking even in the rim region, and no models are currently available for the behavior the dark zone. To address these challenges, the U.S. Department of Energy’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program has employed a multi-scale modeling approach to improve scientific understanding and develop new fuel performance models. In this talk, I will focus on meso-scale efforts, which form a crucial link between atomic-scale and engineering-scale models. Phase-field modeling combined with cluster dynamics is used to predict the restructuring process in the rim region. Phase-field fracture modeling, informed by atomistic simulations, is used to predict the onset of pulverization in the rim region. Combining these techniques together allows the extent of rim pulverization to be predicted. The formation and evolution of the dark zone has also been simulated with the phase-field method, using an improved approach to vacancy source term parameterization. The work shows the important impact of microstructure on fuel performance.

fracture↗
DOE OSTI2021

Coupling particle scale model and SuperDEM–CFD for multiscale simulation of biomass pyrolysis in a packed bed pyrolyzer

An efficient biomass pyrolysis process requires a comprehensive understanding of the chemical and physical phenomena that occur at multi-length and time scales. In this study, a multiscale computational approach was developed and validated for biomass pyrolysis in a packed-bed reactor by integrating pyrolysis kinetics, a particle scale model, and SuperDEM-CFD in open-source code MFiX. A one-dimensional particle-scale model that discretizes the characteristic length of biomass particle into layers was developed to predict the intraparticle phenomena inside a single particle. The 1D model was validated by comparing it with a single biomass particle pyrolysis experiment. Here, a recently developed SuperDEM-CFD model was employed to simulate the non-spherical particle-particle contact and fluid-particle interaction. The coupled model was applied to simulate the pyrolysis of cubic biomass particles in a packed bed and validated by comparing with experimental data. Simulation with and without particle-scale model was compared, and the effect of the gas-solid heat transfer models was also investigated.

09 BIOMASS FUELS↗
DOE OSTI2020

Towards the Reconstruction of Integrated Genome-Scale Models of Metabolism and Gene Expression

The reconstruction of integrated genome-scale models of metabolism and gene expression has been a challenge for a while now. In fact, various methods that allow integrating reconstructions of Transcriptional Regulatory Networks, gene expression data or both into Genome-Scale Metabolic Models have been proposed. Several of these methods are surveyed in this article, which allowed identifying their strengths and weaknesses concerning the reconstruction of integrated models for multiple prokaryotic organisms. Additionally, the main resources of regulatory information were also surveyed, as the existence of novel sources of regulatory information and gene expression data may contribute for the improvement of methodologies referred herein.

Databases of regulatory information↗
DOE OSTI2019

Particle scale modeling of CuFeAlO 4 during reduction with CO in chemical looping applications

Particle scale models that couple reaction phenomena to changes in the solid-state chemistry of an oxygen carrier system are critical to the advancement of the chemical looping concept by allowing for a means to assess process scale up. This work presents an analysis of the reduction for a CuFeAlO 4 oxygen carrier with Carbon Monoxide (CO). The analysis was utilized to aid in the application of particle scale model representation of the carrier system. An experimentally driven study was conducted to provide an array of operational/parametric data sets for the analysis and their impact accessed. Quantification of the cubic spinel oxide phase and changes due to lattice oxygen depletion from reduction were explored to link the solid-state chemistry changes to the reaction progression. Reduction occurred in a multistep process as oxygen was depleted from the structure. Oxygen bound to Cu cations were the first to react with CO. As oxygen was depleted further phase re-orientation occurred resulting in an iron based aluminate (FeAl 2 O 4 ) with discrete metallic copper present. FeAl 2 O 4 was further depleted of oxygen to metallic Fe and alumina. The multistep process was emulated through the use of a multi-interface Grainy pellet model. To add to the utility of the model, the effects of product gas, CO 2 , on the reaction progression were incorporated into the description. In addition, the catalytic effects of the Boudouard reaction were examined and incorporated into the representation adding to the novelty of the work.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1993

A multiple-scale model for compressible turbulent flows

A multiple-scale model for compressible turbulent flows is proposed. It is assumed that turbulent eddy shocklets are formed primarily by the 'collisions' of large energetic eddies. The extra straining of the large eddy, due to their interactions with shocklets, enhances the energy cascade to smaller eddies. Model transport equations are developed for the turbulent kinetic energies and the energy transfer rates of the different scale. The turbulent eddy viscosity is determined by the total turbulent kinetic energy and the rate of energy transfer from the large scale to the small scale, which is different from the energy dissipation rate. The model coefficients in the modeled turbulent transport equations depend on the ratio of the turbulent kinetic energy of the large scale to that of the small scale, which renders the model more adaptive to the characteristics of individual flow. The model is tested against compressible free shear layers. The results agree satisfactorily with measurements.

Liou, William W.↗