Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

A diffusion–deformation model with damage for polymer undergoing rapid decompression failure

Green hydrogen is emerging as one of the most promising alternatives to replace fossil fuels. While hydrogen gas has a good energy density by weight, its poor energy density by volume requires it to be stored under high pressure for commercial use. The hydrogen infrastructure developed to handle this high pressure hydrogen contains multiple components made of polymers as sealing agents. Although polymers do not react chemically with hydrogen gas, they undergo a mechanical failure when high pressure hydrogen gas is suddenly depressurized. This phenomenon known as 'rapid decompression failure' occurs due to the diffusion of hydrogen through polymer and getting trapped inside pre-existing cavities or voids. Here, in this paper, a continuum mechanics-based coupled diffusion-deformation-damage model was developed to predict the hydrogen distribution, stress distribution, and damage propagation inside the polymer while it undergoes rapid decompression failure. The polymer was modeled as a hyperelastic material because it represents the nonlinear material response observed in uniaxial tensile tests perfectly. The effects of hydrogen diffusivity, pre-existing cavity size, cavity location, applied hydrogen pressure, and depressurization rate on damage initiation were studied. It was found that the coefficient of diffusion plays an important role in damage initiation and damage was mostly concentrated in the inside areas rather than near the surface. Experiments were conducted with EPDM polymer which agreed well with the predicted trends using the given model. The effect of adding carbon black and silica filler particles and plasticizer to the pure EPDM polymer was also studied. It was found that damage during RDF decreases with the addition of fillers, but increases with the addition of the plasticizer. Finally, the damage evolution in the presence of two cavities was also studied, and was found that the interaction of stress fields around the cavities alters the damage occurring during RDF.

36 MATERIALS SCIENCE↗

The Problem of Torsion in Prismatic Members of Circular Segmental Cross Section

The problem is solved by approximation, by setting up a function complying with the differential equation of the stress function, and determining the coefficients appearing in it in such a way that the boundary condition is fulfilled as nearly as possible. For the semicircle, for which the solution is known, the method yields very accurate values; the approximated stress distribution is in good agreement with the accurately computed distribution. Stress and strain measurements indicate that the approximate solution is in sufficiently exact agreement with reality for segmental cross sections.

Weigand, A.↗

Measurement of probability distributions for internal stresses in dislocated crystals

Here, we analyse residual stress distributions obtained from various crystal systems using high resolution electron backscatter diffraction (EBSD) measurements. Histograms showing stress probability distributions exhibit tails extending to very high stress levels. We demonstrate that these extreme stress values are consistent with the functional form that should be expected for dislocated crystals. Analysis initially developed by Groma and co-workers for X-ray line profile analysis and based on the so-called “restricted second moment of the probability distribution” can be used to estimate the total dislocation density. The generality of the results are illustrated by application to three quite different systems, namely, face centred cubic Cu deformed in uniaxial tension, a body centred cubic steel deformed to larger strain by cold rolling, and hexagonal InAlN layers grown on misfitting sapphire and silicon carbide substrates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An improved three-point bending test method for the investigation of nanosecond laser dicing of ultrathin Si dies with Cu stabilization layer

Highlights: • A selective chemical etching method has been developed for removal of metallization layers on ultrathin Si dies for three-point bending test. • The complex elastoplastic stress distribution in the die is simplified to an elastic stress distribution. • The die sidewall fracture strength can be determined using the standard three-point bending tensile stress equation. • The characteristic fracture strengths of ultrathin Si dies were correlated to the laser-induced microstructures of the die sidewall. - Abstract: The sidewall fracture strength of ultrathin Si dies with frontside and backside metallization layers cannot be determined directly from three-point bending (3PB) test. The complex 3PB elastoplastic stress distribution makes it difficult to determine the die sidewall fracture strength by analytical method or finite element analysis due to various theoretical and practical constraints. In this work, a selective chemical etching method has been developed for complete removal of the frontside and backside metallization layers on the ultrathin die without affecting the critical microstructure and strength of the die sidewall induced by laser dicing. By removing all the metallization layers on the die, the complex 3PB elastoplastic stress distribution is simplified to an elastic stress distribution. This enables a straightforward calculation of the die sidewall fracture strength using the standard 3PB tensile stress equation for a homogeneous linear elastic material with a rectangular cross section. Two chemical etchants were evaluated and found to be suitable but FeCl{sub 3} is preferred because of the much faster etching time. With this improved 3PB test method, the effect of nanosecond laser dicing on ultrathin Si dies with backside Cu layer was investigated. The die frontside and backside characteristic fracture strengths of ultrathin Si dies with varying backside Cu thickness were determined and correlated to TEM analyses of the compositions and microstructures at the fracture origins.

36 MATERIALS SCIENCE↗

Numerical analysis of temperature and stress fields in hybrid indium antimonide arrays detector with laser irradiation

Thermal-stress effects are the major cause of failure in infrared focal-plane arrays detector, during laser irradiation. Based on the established three-dimensional structural model of hybrid indium antimonide infrared focal-plane arrays, the temperature and stress fields of hybrid indium antimonide detectors irradiated by 1.064-μm Gauss pulsed laser are studied, considering the temperature-dependent material parameters. The results indicate that the temperature increase and thermal stress effects are different, in each layer. Especially in indium antimonide chip, which is the uppermost layer of the indium antimonide detector that directly absorbs laser energy, the temperature shows not a smooth decrease as laser intensity from centre to outside, but a concentric-ringed ripple decrease with discontinuous high temperature extremum areas; which induces its own unique stress distributions: during the laser irradiation region, the thermal stress in areas above indium bumps is much lower than that in areas above underfill, but the stress distribution outside the laser irradiation region is exactly the opposite. The temperature and stress distribution in other materials are also different from that in indium antimonide chip. The main reason is that each material has different thermal properties, especially indium bump and underfill, which are alternative distribution in middle layers, have quite different thermal parameters. All these make the temperature and stress distribution in each layer having own characteristics. In addition, the change trend of the maximum temperature and stress in each layer in accordance with the laser pulse number are also studied. The maximum stress as well as temperature always occurs in the indium antimonide chip.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Theoretical and Experimental Evaluation of the Bond Strength Under Peeling Loads

Reliable applications of adhesively bonded joints require understanding of the stress distribution along the bond-line and the stresses that are responsible for the joint failure. To properly evaluate factors affecting peel strength, effects of defects such as voids on the stress distribution in the overlap region must be understood. In this work, the peel stress distribution in a single lap joint is derived using a strength of materials approach. The bonded joint is modeled as Euler-Bernoulli beams, bonded together with an adhesive. which is modeled as an elastic foundation which can resist both peel and shear stresses. It is found that for certain adhesive and adherend geometries and properties, a central void with the size up to 50 percent of the overlap length has negligible effect on the peak peel and shear stresses. To verify the solutions obtained from the model, the problem is solved again by using the finite element method and by treating the adherends and the adhesive as elastic materials. It is found that the model used in the analysis not only predicts the correct trend for the peel stress distribution but also gives rather surprisingly close results to that of the finite element analysis. It is also found that both shear and peel stresses can be responsible for the joint performance and when a void is introduced, both of these stresses can contribute to the joint failure as the void size increases. Acoustic emission (AE) activities of aluminum-adhesive-aluminum specimens with different void sizes were monitored. The AE ringdown counts and energy were very sensitive and decreased significantly with the void size. It was observed that the AE events were shifting towards the edge of the overlap where the maximum peeling and shearing stresses were occurring as the void size increased.

Nayeb-Hashemi, Hamid↗

Preliminary analysis of FCM fuel thermal-mechanical performance under normal and transient conditions

Fully ceramic microencapsulated (FCM) fuel is a candidate fuel form to replace commercial UO{sub 2} fuel rod in LWR to enhance fuel reliability under accident conditions. The FCM pellet consists of TRISO particles embedded inside the dense SiC matrix. This fuel design is more complex than conventional LWR fuel, which needs new fuel performance models or analysis tools to assist fuel design and concept evaluation. In this paper an attempt was made to develop a finite element method to analyze FCM fuel pellet thermal-mechanical performance. Three idealized cases of normal operation, power ramp, and LOCA were analyzed. The results showed that the temperature distribution and stress distribution of FCM pellet exhibited a strong non-uniformity. The irradiation strain and creep of buffer layer and PyC (pyrolytic carbon) layers had a strong effect on the mechanical performance of FCM pellet. The hoop stresses of SiC layers and SiC matrix increased significantly during the LOCA and varied with radial positions. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fractal distributions of stress and strength and variations of b-value

A two-dimensional planar fault zone on which the difference between stress and strength follows a fractal distribution is simulated to study the variation of the frequency-magnitude b-value under different distributions of heterogeneities and ambient stress levels. It is suggested that earthquakes occur in regions where this difference exceeds a specified value and that the size of these regions is a measure of the magnitude of the associated earthquake. A systematic variation in b-value is observed. It is found that the b-value has a positive correlation with the fractal dimension of the distribution and is inversely related to the ambient stress level. Observational data are compared with the simulation, showing that the observed b-value variation before and during earthquake sequences is a result of changes in both the ambient stress level and in the fractal dimension of the stress-strength distribution.

Huang, J.↗

A review of turbulence measurements in compressible flow

A survey of turbulence measurements in compressible flows is presented. The majority of turbulence measurements at super- and hypersonic speeds were made for the zero pressure gradient, turbulent boundary layer. It was found that the nondimensional turbulent stress terms for the zero pressure gradient flow appear to agree closely with equivalent incompressible measurements in the outer part of the boundary layer. The stress terms were nondimensionalized by the wall value of shear stress and plotted versus the distance from the wall, nondimensionalized by the boundary-layer thickness. Indirect evaluation of the total shear stress distribution from mean velocity measurements for both super- and hypersonic flows (zero pressure gradient, two-dimensional flows) indicate a near universal distribution. These total shear stress curves also agree very closely with measured incompressible shear stress distributions. Recent laser anemometer measurements of the turbulent Reynolds shear stress (puv), reported by Johnson and Rose for a Mach number 2.9 flow, are in reasonable agreement with the expected total shear stress curve over the outer 60% of the boundary layer.

Sandborn, V. A.↗

Quantum stress and torsion distributions in the deuteron

Stress distributions in the deuteron are related to form factors of the asymmetric energy-momentum tensor through three-dimensional Fourier transforms. There are eleven such form factors, which we calculate in an impulse approximation. We compare the obtained form factors to prior results for the six form factors that have been previously calculated. We then elaborate on the formalism for relating the form factors to internal distributions of mass, mass flux, momentum, stresses, and forces, and obtain results for all of these distributions. We obtain the principal stresses for the symmetric part of the stress tensor, and show that the antisymmetric part describes the reorientation of fermion spin by torsion stress when the nucleon moves between the S and D waves. Force distributions in the nucleons depend on the so-called nonconserved form factors through the Cauchy momentum equation, and are nonradial owing to the presence of tensor forces and spin-orbit coupling.

QCD phenomenology↗

Fatigue flaw growth behavior in stiffened and unstiffened panels loaded in biaxial tension

The effect was investigated of biaxial loading on the flaw growth rate of 2219-T87 aluminum alloy that would be typical of Space Shuttle cryogenic tankage design. The stress distribution and stress concentration factors for several integrally stiffened panels under various loading conditions were obtained. The flaw growth behavior of both stiffened and unstiffened panels under biaxial loading conditions was determined. The effect of a complex stress state was studied by introducing flaws in fillet areas of biaxially loaded stiffened panels.

Beck, E. J.↗

Longitudinal compressive failure modes in fiber composites End attachment effects on IITRI type test specimens

The end-attachment effects on longitudinal compressive strength of IITRI type specimen unidirectional fiber composites are formally assessed using finite-element analysis (FEA) in conjunction with composite mechanics. Sixteen different cases were analyzed to evaluate end-attachment effects (such as degree of misalignment, type of misalignment, progressive end-tab debonding, and specimen thickness) on stress distribution, peak stresses, buckling loads, and buckling mode shapes. The results obtained from the FEA and comparisons with fractured specimens show that eccentricities induce bending-type stresses which peak near the end-tabs and cause flexural type fracture. Also, guidelines are included for placing back-to-back strain gages to measure the presence/absence of possible end-attachment and eccentricity effects.

Chamis, C. C.↗

A hybrid-stress finite element for linear anisotropic elasticity

Standard assumed displacement finite elements with anisotropic material properties perform poorly in complex stress fields such as combined bending and shear and combined bending and torsion. A set of three dimensional hybrid-stress brick elements were developed with fully anisotropic material properties. Both eight-node and twenty-node bricks were developed based on the symmetry group theory of Punch and Atluri. An eight-node brick was also developed using complete polynomials and stress basis functions and reducing the order of the resulting stress parameter matrix by applying equilibrium constraints and stress compatibility constraints. Here the stress compatibility constraints must be formulated assuming anisotropic material properties. The performance of these elements was examined in numerical examples covering a broad range of stress distributions. The stress predictions show significant improvement over the assumed displacement elements but the calculation time is increased.

Fly, Gerald W.↗

Analysis of precracking parameters and fracture toughness for ceramic single-edge-precracked-beam specimens

The single-edge-precracked-beam (SEPB) method involves creation of a straight-through crack from an indentation crack. The straight-through crack is developed by applying a controlled bending load to a specimen via a precracking fixture. The fixture induces the following sequence: (1) stable growth of the indentation crack; (2) pop-in; and finally, (3) arrest-thereby forming a straight-through precrack. The effects of indentation load on precracking load as well as precrack size were studied for experimental variables such as specimen width, fixture span, and material. Finite element analysis was used to obtain the stress distribution and stress intensity factor, thus providing a quantitative prediction of the precracking load and precrack size for silicon nitride, alumina, silicon cabide, and two SiC whisker-reinforced silicon nitrides. Fracture toughness values obtained from the SEPB method were compared with those obtained from other methods.

Choi, Sung R.↗

Analysis of precracking parameters for ceramic single-edge-precracked-beam specimens

The single-edge-precracked-beam (SEPB) method involves creation of a straight-through crack from an indentation crack. The straight-through crack is developed by applying a controlled bending load to a specimen via a precracking fixture. The fixture induces the following sequence: (1) stable growth of the indentation crack; (2) pop-in; and finally, (3) arrest - thereby forming a straight-through precrack. The effects of indentation load on precracking load as well as precrack size were studied for experimental variables such as specimen width, fixture span, and material. Finite element analysis was used to obtain the stress distribution and stress intensity factor, thus providing a quantitative prediction of the precracking load and precrack size for silicon nitride, alumina, silicon carbide, and two SiC whisker-reinforced silicon nitrides. Fracture toughness values obtained from the SEPB method were compared with those obtained from other methods.

Choi, Sung R.↗

Gear crack propagation investigations

Analytical and experimental studies were performed to investigate the effect of gear rim thickness on crack propagation life. The FRANC (FRacture ANalysis Code) computer program was used to simulate crack propagation. The FRANC program used principles of linear elastic fracture mechanics, finite element modeling, and a unique re-meshing scheme to determine crack tip stress distributions, estimate stress intensity factors, and model crack propagation. Various fatigue crack growth models were used to estimate crack propagation life based on the calculated stress intensity factors. Experimental tests were performed in a gear fatigue rig to validate predicted crack propagation results. Test gears were installed with special crack propagation gages in the tooth fillet region to measure bending fatigue crack growth. Good correlation between predicted and measured crack growth was achieved when the fatigue crack closure concept was introduced into the analysis. As the gear rim thickness decreased, the compressive cyclic stress in the gear tooth fillet region increased. This retarded crack growth and increased the number of crack propagation cycles to failure.

Lewicki, David G.↗

Analysis Supporting MSFC Cryostat Testing Unit

This report summarizes the results obtained from an analysis of the NASA Marshall Spaceflight Center (MSFC) cryostat testing unit. A finite element model was generated to determine both temperature distribution and stress distribution in the cryostat testing unit for load conditions supplied by MSFC. This report contains the results of that analysis.

Foster, Winfred A., Jr.↗