Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sand heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Avalanches and the distribution of solar flares

The solar coronal magnetic field is proposed to be in a self-organized critical state, thus explaining the observed power-law dependence of solar-flare-occurrence rate on flare size which extends over more than five orders of magnitude in peak flux. The physical picture that arises is that solar flares are avalanches of many small reconnection events, analogous to avalanches of sand in the models published by Bak and colleagues in 1987 and 1988. Flares of all sizes are manifestations of the same physical processes, where the size of a given flare is determined by the number of elementary reconnection events. The relation between small-scale processes and the statistics of global-flare properties which follows from the self-organized magnetic-field configuration provides a way to learn about the physics of the unobservable small-scale reconnection processes. A simple lattice-reconnection model is presented which is consistent with the observed flare statistics. The implications for coronal heating are discussed and some observational tests of this picture are given.

Lu, Edward T.↗
NASA NTRS1975

Accelerations experienced during low-G flight of Black Brant VC (NAS 21.015) on 4 October 1974

This investigation was to determine whether a Black Brant VC (BBVC) sounding rocket equipped with the Goddard Space Flight Center (GSFC) rate control system (RCS) would produce g-levels which are satisfactory for space processing. Accelerations measured by the Marshall Space Flight Center (MSFC) low-g accelerometer system (LGAS) were compared with accelerations calculated from measured payload RCS gyro data during a low-g flight of BBVC NAS 21.015 at White Sands Missile Range, N.M., on October 4, 1974. Accelerations of up to 0.0002 g existed at the LGAS accelerometers from 70 through 420 sec (5.8 min), with the exception of a spike at 101 sec of 0.0004 g which occurred when the RCS was activated the second time. Accelerations of 0.0001 g existed from 140 through 400 sec (4.3 min). Accelerations of 0.0002 g along the roll axis up to 150 sec and of 0.0015 g in the lateral plane at about 135 sec are being investigated by GSFC. They may be associated with leaking thruster valves or a leak in one of the heat pipe experiments. The vehicle rate buildup each time after the RCS nulls out are also being investigated by GSFC. This rate caused most of the 0.0001 g acceleration experienced after 150 sec into the flight. Aerodynamic drag produced no significant accelerations after about 80 sec. The principal conclusion was that the BBVC with the GSFC RCS produces g-levels satisfactory for space processing.

Kissel, R.↗
NASA NTRSDate not supplied

Influence of Airfoil Angle of Attack on Ice Accretion Roughness

The influence of airfoil angle attack on roughness evolution and spatial variation was investigated in the Icing Research Tunnel (IRT) at the NASA Glenn Research Center. Two airfoil models were used for the study: a 53.34-cm (21-in.) NACA 0012 model and a 152.4-cm (60-in.) HAARP-II model. For the NACA 0012, the angle of attack was varied from 0° to 3°, and the ice accretion roughness was characterized while keeping the other icing parameters such as freestream velocity, freestream stagnation temperature, accumulation parameter, and median volumetric diameter (MVD) constant. For the HAARP-II, the angle of attack was varied from -1.9°, which is the non-lifting angle of attack for the airfoil, to 3°. A series of accumulation time progression cases for the HAARP-II at 2.3° angle of attack was also performed in Appendix C and Appendix O conditions and compared to the measurements presented by McClain et al. (2018) for the non-lifting angle of attack condition. The results demonstrate the strong influence of the changing local static pressure along the surface influencing the roughness characteristics. A correlation approach for the maximum equivalent sand-grain roughness along the surface of an airfoil is presented and considers the scaled accumulation time, the stagnation point freezing fraction, and the surface pressure relative to the static and stagnation pressures of the flow. Finally, an attempt to relate the maximum roughness quantities to local pressure coefficients and local icing quantities is presented and discussed.

Icing↗
NASA NTRS2007

Joint Test Report For Validation of Alternatives to Aliphatic Isocyanate Polyurethanes

National Aeronautics and Space Administration (NASA) and Air Force Space Command (AFSPC) have similar missions and therefore similar facilities and structures in similar environments. The standard practice for protecting metallic substrates in atmospheric environments is the application of an applied coating system. The most common topcoats used in coating systems are polyurethanes that contain isocyanates. Isocyanates are classified as potential human carcinogens and are known to cause cancer in animals. The primary objective of this effort was to demonstrate and validate alternatives to aliphatic isocyanate polyurethanes resulting in one or more isocyanate-free coatings qualified for use at AFSPC and NASA installations participating in this project. This joint Test Report (JTR) documents the results of the laboratory and field testing as well as any test modifications made during the execution of the testing. The technical stakeholders agreed upon test procedure modifications documented in this document. This JTR is made available as a reference for future pollution prevention endeavors by other NASA centers, the Department of Defense and commercial users to minimize duplication of effort. All coating system candidates were tested using approved NASA and AFSPC standard coating systems as experimental controls. This study looked at eight alternative coating systems and two control coating systems and was divided into Phase I Screening Tests, Phase II Tests, and Field Testing. The Phase I Screening Tests were preliminary tests performed on all the selected candidate coating systems. Candidate coating systems that did not meet the acceptance criteria of the screening tests were eliminated from further testing. Phase I Screening Tests included: Ease of Application, Surface Appearance, Dry-To-Touch (Sanding), Accelerated Storage Stability, Pot Life (Viscosity), Cure Time (Solvent Rubs), Cleanability, Knife Test, Tensile (pull-off) Adhesion, and X-Cut Adhesion by Wet Tape After a review of the Phase I test results, four of the alternative coating systems showed substandard performance in relation to the Control Systems and were eliminated from the Phase II testing. Due to the interest of stakeholders and time constraints, however, all eight alternatives were subjected to the following Phase II tests, along with field testing at Stennis Space Center (SSC), Mississippi: Hypergol Compatibility, Liquid Oxygen Compatibility, 18-Month Marine Exposure (Gloss Retention, Color Retention, Blistering, Visual Corrosion, Creepage from Scribe, Heat Adhesion), and Field Exposure (6- and 12-month Evaluation for Coating Condition, Color Retention, Gloss Retention). The remaining four alternative coating systems determined to be the best viable alternatives were carried on to Phase II testing that included: Removability, Repairability, Abrasion Resistance, Gravelometer, Fungus Resistance, Accelerated Weathering, Mandrel Bend Flexibility, and Cyclic Corrosion Resistance. Of the systems that continued to Phase II, three (3) alternative coating systems meet the performance requirements as identified by stakeholders. Two (2) other systems, that were not included in Phase II testing, performed well enough on the 18-Month Marine Exposure, the primary requirement for NASA technical standard NASA-STD-5008, Protective Coating of Carbon Steel, Stainless Steel, and Aluminum on Launch Structures, Facilities, and Ground Support Equipment, that they were also considered to be successful candidates. In total, five (5) alternative coating systems were approved for inclusion in the NASA-STD- 5008 Qualified Products List (QPL). The standard is intended to provide a common framework for consistent practices across NASA and is often used by other entities. The standard's QPL does not connote endorsement of the products by NASA, but lists those products that have been tested and meet the requirements as specified.

Lewis, Pattie↗
NASA NTRS2020

Black Carbon and Precipitation: an Energetics Perspective

Black carbon aerosols (BC) influence precipitation through a range of processes. The climate response to the presence of BC is however highly dependent on its vertical distribution. Here, we analyze the changes in the energy budget and precipitation impacts of adding a layer of BC at a range of altitudes in two independent global climate models. The models are run with atmosphere‐only and slab ocean model setup to analyze both fast and slow responses, respectively. Globally, precipitation changes are tightly coupled to the energy budget. We decompose the precipitation change into contributions from absorption of solar radiation, atmospheric longwave radiative cooling, and sensible heat flux at the surface. We find that for atmosphere‐only simulations, BC rapidly suppress precipitation, independent of altitude, mainly because of strong atmospheric absorption. This reduction is offset by increased atmospheric radiative longwave cooling and reduced sensible heat flux at the surface, but not of sufficient magnitude to prevent reduced precipitation. On longer timescales, when the surface temperature is allowed to respond, we find that the precipitation increase associated with surface warming can compensate for the initial reduction, particularly for BC in the lower atmosphere. Even though the underlying processes are strikingly similar in the two models, the resulting change in precipitation and temperature by BC differ quite substantially.

black carbon aerosols↗
NASA NTRS1999

Interaction of Space Suits with Windblown Soil: Preliminary Mars Wind Tunnel Results

Experiments in the Mars Wind Tunnel at NASA Ames Research Center show that under Mars conditions, spacesuit materials are highly susceptible to dust contamination when exposed to windblown soil. This effect was suspected from knowledge of the interaction of electrostatically adhesive dust with solid surfaces in general. However, it is important to evaluate the respective roles of materials, meteorological and radiation effects, and the character of the soil. The tunnel permits evaluation of dust contamination and sand abrasion of space suits by simulating both pressure and wind conditions on Mars. The long-term function of space suits on Mars will be primarily threatened by dust contamination. Lunar EVA activities caused heavy contamination of space suits, but the problem was never seriously manifest because of the brief utilization of the suits, and the suits were never reused. Electrostatically adhering dust grains have various detrimental effects: (1) penetration and subsequent wear of suit fabrics, (2) viewing obscuration through visors and scratching/pitting of visor surfaces, (3) penetration, wear, and subsequent seizing-up of mechanical suit joints, (4) changes in albedo and therefore of radiation properties of external heat-exchanger systems, (5) changes in electrical conductivity of suit surfaces which may affect tribocharging of suits and create spurious discharge effects detrimental to suit electronics/radio systems. Additional information is contained in the original.

Marshall, J.↗
NASA NTRS2021

Aerosol Absorption in Global Models From AeroCom Phase III

Aerosol-induced absorption of shortwave radiation can modify the climate through local atmospheric heating, which affects lapse rates, precipitation, and cloud formation. Presently, the total amount of aerosol absorption is poorly constrained, and the main absorbing aerosol species (black carbon (BC), organic aerosols (OA), and mineral dust) are diversely quantified in global climate models. As part of the third phase of the Aerosol Comparisons between Observations and Models (AeroCom) intercomparison initiative (AeroCom phase III), we here document the distribution and magnitude of aerosol absorption in current global aerosol models and quantify the sources of intermodel spread, highlighting the difficulties of attributing absorption to different species. In total, 15 models have provided total present-day absorption at 550 nm (using year 2010 emissions), 11 of which have provided absorption per absorbing species. The multi-model global annual mean total absorption aerosol optical depth (AAOD) is 0.0054 (0.0020 to 0.0098; 550 nm), with the range given as the minimum and maximum model values. This is 28 % higher compared to the 0.0042 (0.0021 to 0.0076) multi-model mean in AeroCom phase II (using year 2000 emissions), but the difference is within 1 standard deviation, which, in this study, is 0.0023 (0.0019 in Phase II). Of the summed component AAOD, 60 % (range 36 %–84 %) is estimated to be due to BC, 31 % (12 %–49 %) is due to dust, and 11 % (0 %–24 %) is due to OA; however, the components are not independent in terms of their absorbing efficiency. In models with internal mixtures of absorbing aerosols, a major challenge is the lack of a common and simple method to attribute absorption to the different absorbing species. Therefore, when possible, the models with internally mixed aerosols in the present study have performed simulations using the same method for estimating absorption due to BC, OA, and dust, namely by removing it and comparing runs with and without the absorbing species. We discuss the challenges of attributing absorption to different species; we compare burden, refractive indices, and density; and we contrast models with internal mixing to models with external mixing. The model mean BC mass absorption coefficient (MAC) value is 10.1 (3.1 to 17.7) m 2 g −1 (550 nm), and the model mean BC AAOD is 0.0030 (0.0007 to 0.0077). The difference in lifetime (and burden) in the models explains as much of the BC AAOD spread as the difference in BC MAC values. The difference in the spectral dependency between the models is striking. Several models have an absorption Ångstrøm exponent (AAE) close to 1, which likely is too low given current knowledge of spectral aerosol optical properties. Most models do not account for brown carbon and underestimate the spectral dependency for OA.

Aerosol absorption↗
NASA NTRS2017

High Temperature Degradation of Advanced Thermal and Environmental Barrier Coatings (TEBCs) by CaO-MgO-Al2O3-SiO2 (CMAS)

There is increasing interest in the degradation studies of thermal and environmental barrier coatings (TEBCs) of gas turbines by molten CaO-MgO-Al2O3-SiO2 (CMAS). CMAS minerals are usually referred as silica-containing sand dust and volcano ash materials that are carried by the intake air into gas turbines, e.g. aircraft engines. The low-melting deposits react at high temperatures (1000C) with the coating materials. This causes degradation and accelerated coating failure of the static and rotating components of the turbine engines. We discuss some preliminary results of the reactions between CMAS and Rare-Earth (RE Y, Yb, Dy, Gd, Nd and Sm) oxide stabilized ZrO2 or HfO2 systems, and the stability of the resulting oxides and silicates. Plasma sprayed hollow tube samples (outer diameter 4.7 mm, wall thickness 0.76 mm and 26 mm height) were half filled with CMAS powder, wrapped and sealed with platinum foil, and heat- treated at 1310 C for 5h. Samples were characterized by differential scanning calorimetry, X-ray diffraction and cross section electron microscopy analysis.

Thermal and environmental barrier coatings↗
NASA NTRS2002

Investigations of Control Surface Seals for Re-entry Vehicles

Re-entry vehicles generally require control surfaces (e.g., rudders, body flaps) to steer them during flight. Control surface seals are installed along hinge lines and where control surface edges move close to the vehicle body. These seals must operate at high temperatures and limit heat transfer to underlying structures to prevent them from overheating and causing possible loss of vehicle structural integrity. This paper presents results for thermal analyses and mechanical testing conducted on the baseline rudder/fin seal design for the X-38 re-entry vehicle. Exposure of the seals in a compressed state at the predicted peak seal temperature of 1900 F resulted in loss of seal resiliency. The vertical Inconel rudder/fin rub surface was re-designed to account for this loss of resiliency. Room temperature compression tests revealed that seal unit loads and contact pressures were below limits set to protect Shuttle thermal tiles on the horizontal sealing surface. The seals survived an ambient temperature 1000 cycle scrub test over sanded Shuttle tiles and were able to disengage and re-engage the tile edges during testing. Arc jet tests confirmed the need for seals in the rudder/fin gap location because a single seal caused a large temperature drop (delta T = 1710 F) in the gap.

Dunlap, Patrick H., Jr.↗
NASA NTRSDate not supplied

Preliminary Measurements on the BOLT Geometry in the Supersonic Low Disturbance Tunnel

Experiments were performed in the Mach 3.5 Supersonic Low Disturbance Tunnel on the BOundary-Layer Transition (BOLT) geometry. The goal of this campaign was to assess changes to the transition front by varying the freestream noise and the model surface quality. The model was printed of polycarbonate and is 30% scale of the flight geometry. It was tested under noisy and quiet conditions at different streamwise positions in the tunnel and was also tested before and after improvements were made to the model surface through sanding and gap reduction. Pitch and yaw angles were nominally zero. The model surface temperature was measured using infrared thermography and thermocouples as the unit Reynolds number was swept from 4.75 – 15.8 × 10 6 m −1 . Boundary-layer transition was observed near the midspan of the model for unit Reynolds numbers above 10×10 6 m −1 in quiet flow, while transition was already observed on the shoulders below 5×10 6 m −1 in noisy flow. The model surface enhancements improved the symmetry of the transition front for quiet flow but made only slight differences for noisy flow. In quiet flow, the impact of streamwise positioning on transition was more significant on the model shoulders compared to the central region. The difference in the shoulder heating was likely due to variation in noise radiated from the nozzle sidewalls. The total temperature and initial wall temperatures were near 300 K and 293 K, respectively, which generally resulted in negative convective heat-flux values into the model. Hot-wire anemometry was also utilized to characterize the freestream and to conduct a planar survey near the base of the model for the 7.92 × 10 6 m −1 quiet condition. The survey captured the thickening of the boundary layer at the centerline and the vortical nature of the flow outboard of it. Spectral analysis of the mass-flux fluctuations near the midspan demonstrates that the boundary layer is laminar and suggests that the thick boundary layer caused the relatively warm centerline observed in the infrared images.

boundary layer transition↗
NASA NTRS1985

Numerical simulation of compressible, turbulent, two-phase flow

A computer program for numerically simulating compressible, turbulent, two-phase flows is described and applied. Special attention is given to flows in which dust is ingested into the turbulent boundary layer behind shock waves moving over the earth's surface. it is assumed that the two phases are interpenetrating continua which are coupled by drag forces and heat transfer. The particle phase is assumed to be dilute, and turbulent effects are modeled by zero- and two-equation eddy viscosity models. An important feature of the turbulence modeling is the treatment of surface boundary conditions which control the ingestion of particles into the boundary layer by turbulent friction and diffusion. The numerical method uses second-order implicit upwind differencing of the inviscid terms of the equations and second-order central differencing of the viscous terms. A diagonal form of the implicit algorithm is used to improve efficiency, and the transformation to a curvilinear coordinate system is accomplished by the finite volume techniques. Applications to a series of representative flows include a two-phase nozzle flow, the steady flow of air over a sand bed, and the air flow behind a normal shock wave in uniform motion over a sand bed. Results of the latter two applications are compared with experimental results.

Coakley, t. J.↗
NASA NTRS1994

Light transmission and reflection in perennially ice-covered Lake Hoare, Antarctica

We have investigated the transmission and albedo of the perennial ice cover on Lake Hoare, Antarctica. Our database consists of year-round measurements of the photosynthetically active radiation (400-700 nm) under the ice, measurements of the spatial variation of the under-ice light in midsummer, and spectrally resolved measurements from 400 to 700 nm of the albedo and transmission of the ice cover in early (November) and in midsummer (January). Our results show that the transmission decreases in the first part of summer, dropping by a factor of approximately 4 from November to January. We suggest that this is due to heating in the upper layers of the ice cover and the formation of Tyndall figures. Later in the summer when a significant liquid water fraction occurs within the ice cover, the transmission increases. In the fall when the ice cover freezes solid the transmission drops markedly. The spectrally resolved measurements from 400 to 700 nm show that approximately 2-5% of the incident light in this spectral region penetrates the 3.5-m thick ice cover. We have analyzed the spectral data using a two-stream scattering solution to the radiative transfer equation with three vertical layers in the ice cover. A surficial glaze of scattering ice 1 cm thick overlies a layer of sandy, bubbly ice about a meter thick, and below this is a thick layer of sand-free ice with bubbles. We find that the ice cover is virtually opaque at wavelengths longer than 800 nm. The net transmission of solar energy is approximately 2%. Significant changes in the thickness of the ice cover have been reported at Lake Hoare. These are due primarily to changes in the thickness of the bottom layer only. Because this layer is relatively clear, the effect on the transmission through the ice cover from these changes is less than would be predicted assuming a homogeneous ice cover.

Mckay, C. P.↗
NASA NTRSDate not supplied

Preliminary Measurements on the BOLT Geometry in the Supersonic Low Disturbance Tunnel

Experiments were performed in the Mach 3.5 Supersonic Low Disturbance Tunnel on the BOundary-Layer Transition (BOLT) geometry. The goal of this campaign was to assess changes to the transition front by varying the freestream noise and the model surface quality. The model was printed of polycarbonate and is 30% scale of the flight geometry. It was tested under noisy and quiet conditions at different streamwise positions in the tunnel and was also tested before and after improvements were made to the model surface through sanding and gap reduction. Pitch and yaw angles were nominally zero. The model surface temperature was measured using infrared thermography and thermocouples as the unit Reynolds number was swept from 4.75 -- 15.8 x 10^6 m^{-1}. Boundary-layer transition was observed near the midspan of the model for unit Reynolds numbers above 10 x 10^6 m^{-1} in quiet flow, while transition was already observed on the shoulders below 5 x 10^6 m^{-1} in noisy flow. The model surface enhancements improved the symmetry of the transition front for quiet flow but made only slight differences for noisy flow. In quiet flow, the impact of streamwise positioning on transition was more significant on the model shoulders compared to the central region. The difference in the shoulder heating was likely due to variation in noise radiated from the nozzle sidewalls. The total temperature and initial wall temperatures were near 300 K and 293 K, respectively, which generally resulted in negative convective heat-flux values into the model. Hot-wire anemometry was also utilized to characterize the freestream and to conduct a planar survey near the base of the model for the 7.92 x 10^6 m^{-1} quiet condition. The survey captured the thickening of the boundary layer at the centerline and the vortical nature of the flow outboard of it. Spectral analysis of the mass-flux fluctuations near the midspan demonstrates that the boundary layer is laminar and suggests that the thick boundary layer caused the relatively warm centerline observed in the infrared images.

boundary layer transition↗
NASA NTRS2017

Thermochemistry of Calcium-Magnesium-Aluminum-Silicate (CMAS) and Components of Advanced Thermal and Environmental Barrier Coating Systems

There is increasing interest in the degradation mechanism studies of thermal and environmental barrier coatings (TEBCs) of gas turbines by molten CaO-MgO-Al(exp. 2)O(exp. 3)-SiO(exp. 2) CMAS). CMAS minerals are usually referred as silicon-containing sand dust and volcano ash materials that are carried by the intake air into gas turbines, e.g. in aircraft engines, and their deposits often react at high temperatures (greater than 1200 degrees C) with the engine turbine coating systems and components. The high temperature reactions causes degradation and accelerated failure of the static and rotating components of the turbine engines. We discuss some results of the reactions between the CMAS and Rare-Earth (RE = Y, Yb, Dy, Gd, Nd and Sm) - oxide stabilized ZrO(exp. 2) or HfO(exp. 2) systems, and the stability of the resulting oxides and silicates. Plasma sprayed hollow tube samples (outside diameter = 4.7 mm, wall thickness = 0.76 mm and = 26 mm height) were half filled with CMAS powder, wrapped and sealed with platinum foil, and heat treated at 1310 degrees C for 5h. Samples were characterized by differential scanning calorimetry (DSC), X-ray diffraction, and cross-section electron microscopy analysis and energy dispersive X-ray spectroscopy. It was found that CMAS penetrated the samples at the grain boundaries and dissolved the TEBC materials to form silicate phases containing the rare-earth elements. Furthermore, it was found that apatite crystalline phases were formed in the samples with total rare-earth content higher than 12 mol% in the reaction zone for the ZrO(exp. 2) system. In general, samples with the nominal compositions (30YSZ), HfO(exp. 2)-7Dy(exp. 2)O(exp. 2) and ZrO(exp. 2)-9.5Y(exp. 2)O(exp. 3)-2.25Gd(exp. 2)O(exp. 3)-2.25Yb(exp. 2)O(exp. 3) exhibited lower reactivity or more resistance to CMAS than the other coating compositions of this work.

degradation↗
NASA NTRS1992

Albedo patterns and gypsum generation in the central Namib Desert - Land, sea and air interactions on an arid West Coast

In the central Namib Desert, dune-free surfaces are separated abruptly from a sea of yellow and red sand dunes at the Kuiseb River canyon. The off-white hues of the dune-free area result from anomalously high surficial gypsum enrichment. Satellite imagery indicates that the gypsum surfaces are associated with lower surface maximum temperatures than those of the darker dune surfaces to the south. One of various sources of sulfate for the gypsum bodies is oceanic H2S, supplied to desert land-surfaces by regular fog incursions. Since fog events are widespread along the coast, the question of anomalous gypsum accumulations north of the dune sea arises. Satellite imagery, in conjunction with more detailed handheld photography from the space shuttle, indicates that the penetration of fog inland is significantly greater over the gypsum surfaces than it is over the dunes. It is postulated that the thermal gradient between these surfaces generates a heat low centered over the northern part of dune sea and that this enhances fog and H2S advection on its north side onto the nearby dune-free zone. In such a system, gypsum/caliche surfaces reinforce advection of fog over themselves in a positive feedback mode.

Wilkinson, M. J.↗
NASA NTRS2003

The Origin of Chondrites: Metal-Silicate Separation Experiments Under Microgravity Conditions, Experiment 2

Chondrites are categorized into different groups by several properties, including the metal-to-silicate ratio. Various processes have been suggested to produce distinct metal/silicate ratios, some based on sorting in the early solar nebular and others occurring after accretion on the parent body. Huang et al. suggested that a weak gravitational field accompanied by degassing, could result in metal/silicate separation on parent bodies. We suggest that asteroids were volatile-rich, at least early in their histories. Spectroscopic evidence from asteroid surfaces indicates that one-third of all asteroids maybe rich in clays and hydrated minerals, similar to carbonaceous chondrites. Internal and/or external heating could have caused volatiles to evaporate and pass through a surface dust layer. Spacecraft images of asteroids show they have a thick regoliths. Housen, and Asphaug and Nolan proposed that even a 10 km diameter asteroid could potentially have a significant regolith. Grain size and grain density sorting could occur in the unconsolidated layer by the process known as fluidization. This process occurs when an upward stream of gas is passed through a bed of particles which are lifted against a gravitational force. Fluidization is commonly used commercially to sort particulates. This type of behavior is based upon the bed, as a whole, and differs from aerodynamic sorting. Two sets of reduced gravity experiments were conducted during parabolic flights aboard NASA's KC-135 aircraft. The first experiment employed 310 tubes of 2.5 cm diameter, containing mixtures of sand and metal grains. A gas source was used to fluidize the mixture at reduced gravity conditions and mixtures were analyzed after the flight. However, this experiment did not allow a description of the fluidization as a function of gravity. A second experiment was conducted on the KC-135 aircraft in the summer of 2001, consisting of two Plexiglas cylinders containing a metal/silicate mixture, and video cameras to record the experiment on tape. Here we summarize this experiment and discusses the implications for metalsilicate separation on asteroid bodies.

Moore, S. R.↗
NASA NTRS1989

Summary of activities

Four space projects' activities are summarized. Design work on the Mars Penetrator Project, in cooperation with the NASA Ames Research Center, is being continued. Efforts are focused on the drilling mechanism which must penetrate the martian subsurface soil to collect and retrieve an uncontaminated sample. The new design consists of a rotary-percussive drill mechanism. This mechanism is optimum for dry drilling, necessary to avoid contamination of the soil sample, in many different soil types. The need for a small, relatively inexpensive device to study the chemical structure of this martian soil was also established. The egg design was chosen for its low cost compared to other systems and potential for a large number of eggs to be deployed on the martian surface. The design process included analysis of the dynamics of reentry, dissipation of heat during reentry, impact with the surface, access to undisturbed soil samples, and ability to gather samples from the soil at three depths. The egg consists of the reentry systems, soil probe lifting system, soil probe package, gas chromatograph, transmitter, and battery power supply. The egg must function only once, but is designed to withstand one martian year. The Mars Mole is designed as a rover-based device which penetrates the martian soil to a depth of up to 10 m, obtains a sample of soil, and returns it to the surface for analysis. The mole was designed to meet the following specifications: (1) weight less than 10 kg; (2) size less than 20 x 20 x 30 cm; (3) power less than 100 W; (4) ability to obtain a sample of at least 5 cc; (5) ability to penetrate fine, loose sand; and (6) need to obtain at least one sample. The space station umbilical connector project is a device which provides the translational motion of the connectors on the Space Station Freedom to allow engagement for power and data transfer. The design is capable of delivering a 20 lb force within the necessary tolerances and will operate reliably in the space environment.

Source record↗
NASA NTRS2006

Advanced Coating Removal Techniques

An important step in the repair and protection against corrosion damage is the safe removal of the oxidation and protective coatings without further damaging the integrity of the substrate. Two such methods that are proving to be safe and effective in this task are liquid nitrogen and laser removal operations. Laser technology used for the removal of protective coatings is currently being researched and implemented in various areas of the aerospace industry. Delivering thousands of focused energy pulses, the laser ablates the coating surface by heating and dissolving the material applied to the substrate. The metal substrate will reflect the laser and redirect the energy to any remaining protective coating, thus preventing any collateral damage the substrate may suffer throughout the process. Liquid nitrogen jets are comparable to blasting with an ultra high-pressure water jet but without the residual liquid that requires collection and removal .As the liquid nitrogen reaches the surface it is transformed into gaseous nitrogen and reenters the atmosphere without any contamination to surrounding hardware. These innovative technologies simplify corrosion repair by eliminating hazardous chemicals and repetitive manual labor from the coating removal process. One very significant advantage is the reduction of particulate contamination exposure to personnel. With the removal of coatings adjacent to sensitive flight hardware, a benefit of each technique for the space program is that no contamination such as beads, water, or sanding residue is left behind when the job is finished. One primary concern is the safe removal of coatings from thin aluminum honeycomb face sheet. NASA recently conducted thermal testing on liquid nitrogen systems and found that no damage occurred on 1/6", aluminum substrates. Wright Patterson Air Force Base in conjunction with Boeing and NASA is currently testing the laser remOval technique for process qualification. Other applications of liquid nitrogen operations include cutting of both soft and hard materials. While the laser will not cut materials, it can be used to roughen surfaces and to remove other materials from the substrate including oil, grease, and mold. The space program can benefit from several of these applications with the need for precise removal of coatings and other organic compounds in areas adjacent to sensitive space flight hardware. Significant advantages are evident when comparing liquid nitrogen and laser removal operations over current techniques of media blasting and sanding.

Seibert, Jon↗